ULTRA GRIP

PART A – BASE
SAFETY DATA SHEET

Page 1 – 3/13/2023
1. Product and Company Identification

Product Name ULTRA GRIP – PART A BASE (GALLON)

Company Name: SlipDoctors

2101 Midway Road, Suite 350
Carrollton, TX 75006

Phone Number: +972-999-9998

Emergency Contact: Emergencies Involving Spills, Leaks, Fires, Exposures, or Accidents

CHEMTREC: (800) 424-9300

2. Hazards Identification

Skin Corrosion/Irritation, Category 2

Skin Sensitization, Category 1
Serious Eye Damage/Eye Irritation, Category 2A
Aquatic Toxicity (Chronic), Category 2
Target Organ Systemic Toxicity (single exposure), Category 3
Flammable Liquids, Category 3

GHS Signal Word: Danger

GHS Hazard Phrases: H315 - Causes skin irritation.
H316 - Causes mild skin irritation.
H317 - May cause an allergic skin reaction.
H319 - Causes serious eye irritation.
H335 - May cause respiratory irritation.
H372 - Causes damage to organs through prolonged or repeated exposure.
H373 - May cause damage to organs through prolonged or repeated exposure.

H411 - Toxic to aquatic life with long lasting effects.

GHS Precaution Phrases: P260 - Do not breathe dust/fume/gas/mist/vapors/spray.
P264 - Wash hands thoroughly after handling.
P270 - Do not eat, drink or smoke when using this product.
P271 - Use only outdoors or in a well-ventilated area.
P272 - Contaminated work clothing should not be allowed out of the workplace.
P273 - Avoid release to the environment.
P280 - Wear protective gloves/protective clothing/eye protection/face protection.

GHS Response Phrases: P301+330+331 – IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Get medical aid.
P303+361+353 - IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse skin
with water/shower.
P304+340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Get medical attention.
P305+351+338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
P332+313 – If skin irritation occurs, get medical advice/attention.
P337+313 - If eye irritation persists, get medical advice/attention.
P370+378 - In case of fire, use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam.
GHS Storage and Disposal P403+235 – Store in cool/well-ventilated place. Store locked up.
Phrases: P501-Contact a licensed professional waste disposal service to dispose of this material.
SLIPDOCTORS ULTRA GRIP PART A – SAFETY DATA SHEET 03/13/2023 PAGE 2 OF 5

Potential Health Effects

(Acute and Chronic): Chronic inhalation may cause effects similar to those of acute inhalation.
Inhalation: Material is irritating to mucous membranes and upper respiratory tract. Harmful if inhaled. Inhalation
of high concentrations may cause central nervous system effects characterized by nausea, headache,
dizziness, unconsciousness and coma. Vapors may cause dizziness or suffocation.
Skin Contact: May be harmful if absorbed through the skin. Prolonged and/or repeated contact may cause irritation
and/or dermatitis.
Eye Contact: Causes eye irritation. Causes redness and pain.
Ingestion: May be harmful if swallowed. May be harmful if inhaled. May cause irritation of the digestive tract. May
cause gastrointestinal irritation with nausea, vomiting and diarrhea. May cause central nervous system
depression, characterized by excitement, followed by headache, dizziness, drowsiness, and nausea.
Advanced stages may cause collapse, unconsciousness, coma and possible death due to respiratory failure.
Aspiration of material into the lungs may cause chemical pneumonitis, which may be fatal.

3. Composition/Information on Ingredients

CAS # Hazardous Components (Chemical Name) Concentration

14808-60-7 Silicon Dioxide 30.0 - 40.0%

25068-38-6 Epoxy Resin 20.0 - 30.0%

1344-28-1 Aluminum Oxide 10.0 - 20.0%
13463-67-7 Titanium Dioxide 5.0 - 15.0%
107-98-2 2-Propanol, 1-Methoxy- 1.0 - 10.0%
1333-86-4 Black Pigment .01 - 1.0%

4. First Aid Measures

Emergency and First Aid Procedures:

In Case of Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxygen. Remove from exposure and move to fresh air
immediately. Get medical aid.
In case of Skin Contact: Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash
clothing before reuse. If skin irritation occurs, get medical advice/attention.
In Case of Eye Contact: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Get medical
aid immediately.
In Case of Ingestion: Never give anything by mouth to an unconscious person. Rinse mouth with water. Do NOT induce vomiting. Get
medical aid.
Note to Physician: Consult a physician. Show this safety data sheet to the doctor in attendance. Move out of dangerous area. Treat
symptomatically and supportively.

5. Fire Fighting Measures

Suitable Extinguishing Use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam. For large fires, apply water from far as
Media: possible. Use very large quantities (flooding) of water applied as a mist or spray; solid streams of water may be
ineffective. Cool all affected containers with flooding quantities of water.
Fire Fighting Use water spray to cool unopened containers. Protective Equipment: Wear self-contained breathing apparatus and
Instructions: protective clothing to prevent contact with skin and eyes. Specific Hazard(s): Flammable Liquid. Emits toxic fumes
under fire conditions. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or
combustion. Use water spray to keep fire-exposed containers cool. Flammable liquid and vapor. Vapors are heavier
than air and may travel to a source of ignition and flash back. Vapors can spread along the ground and collect in low
or confined areas.
Flammable Properties Vapor may travel considerable distance to source of ignition and flash back. Container explosion may occur under
and Hazards: fire conditions. Forms explosive mixtures in air.
SLIPDOCTORS ULTRA GRIP PART A – SAFETY DATA SHEET 03/13/2023 PAGE 3 OF 5

6. Accidental Release Measures

Steps to be Taken in Personal Precautions. Use personal protective equipment.

Case Material is
Spills/Leaks: Control runoff and isolate discharged material for proper disposal. Use water spray to cool and
Released or Spilled: disperse vapors.

7. Handling and Storage

Precautions to be Avoid contact with skin and eyes. Normal measures for preventive fire protection. Avoid inhalation of vapor or
Taken in Handling: mist. Keep away from sources of ignition - No smoking. Take measures to prevent the build-up of electrostatic
charge.
Precautions to be Containers which are opened must be carefully resealed and kept upright to prevent leakage. Keep away from heat,
Taken in Storage: sparks, and open flame.

8. Exposure Controls/Personal Protection

CAS # Partial Chemical Name OSHA TWA ACGIH TWA

14808-60-7 Silicon Dioxide PEL: 8825 ppm (%SiO2+5) TLV: 0.05 mg/m3 (R)
25068-38-6 Epoxy Resin N/E N/E
1344-28-1 Aluminum Oxide PEL: 15 (dust); 5 (resp.) mg/m3 TLV: 10 mg/m3 (E)
13463-67-7 Titanium Dioxide PEL: 26 (dust) mg/m3 N/E
107-98-5 2-Propanol, 1-Methoxy- PEL: 100 ppm TLV: 100 ppm
STEL: 150 ppm
1333-86-4 Black Pigment N/E N/E

Respiratory Equipment For higher level protection use type OV/AG/P99 (US) or type ABEK-P2 (EU EN 143) respirator cartridges. Use
(Specify Type): respirators and components tested and approved under appropriate government standards such as NIOSH (US)
or CEN (EU). Where risk assessment shows air-purifying respirators are appropriate use a full-face respirator
with multi- purpose combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering
controls.
Eye Protection: Safety glasses with side shield. For a higher degree of protection, wear chemical splash goggles.
Protective Gloves: Wear appropriate protective gloves to prevent skin exposure, such as butyl rubber or nitrile rubber.
Other Protective Wear appropriate protective clothing to prevent skin exposure.
Clothing:
Engineering Controls: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use
adequate general or local exhaust ventilation to keep airborne concentrations below the permissible exposure
limits.
Work, Hygienic, Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the
Maintenance Practices: end of workday. Wash thoroughly after handling Wash contaminated clothing before reuse.

9. Physical and Chemical Properties

Physical States: [ ] Gas [ X ] Liquid [ ] Solid

Flash Point: 88°F
Boiling Point: 243°F
Explosive Limits: LEL: 1.5 UEL: 13.74
Weight per Gallon: 16.20 + 1.0
Vapor Pressure (mm Hg): 11.8 @ 68°F
Vapor Density: Heavier than Air
Evaporation Rate: Slower than Ether
Percent Volatile: 8 (Vol)
SLIPDOCTORS ULTRA GRIP PART A – SAFETY DATA SHEET 03/13/2023 PAGE 4 OF 5

10. Stability and Reactivity

Stability: Unstable [ ] Stable [ X ]

Conditions to Avoid: Heat, flames, and sparks

Instability:
Incompatibility –
Bases, Strong oxidizing agents
Materials to Avoid
Hazardous
Decomposition Nature of decomposition products unknown.
Byproducts:
Possibility of Hazardous
Will occur [ ] Will not occur [ X ]
Reactions:
Conditions to Avoid –
No data available
Hazardous Reactions:

11. Toxicological Information

Toxicological Information: Germ cell mutagenicity. Reproductive toxicity – no data available

Germ cell mutagenicity. Reproductive toxicity – no data available
Specific target organ toxicity – repeated exposure (Globally Harmonized System)
Aspiration hazard. Inhalation: May cause damage to organs through prolonged or repeated exposure.
Epidemiology: Teratogenicity: No information available Reproductive Effects:
Carcinogenicity & Other This product contains more than 0.1% crystalline silica (CAS #14808-60-7) which has been classified by
Information: IARC a Class 1 carcinogen. Normal application procedures pose no hazard since the silica is set and
encapsulated, but grinding or sanding dried films may yield respirable silica dusts. Control exposures to
less than 0.1 mg per cubic meter of air using approved dust filter respirators. Skin contact: Prolonged or
repeated contact with product may cause slight skin irritation. Impervious gloves should be worn if
prolonged skin contact is likely.
ACGIH Carcinogens Quartz (CAS 14808-60-7) A2 Suspected human carcinogen
IARC Monographs, Overall
Evaluation of Quartz (CAS 14808-60-7) 1 Carcinogenic to humans
Carcinogenicity
US NTP Report on Quartz (CAS 14808-60-7) Known to be human carcinogen.
Carcinogens:
OSHA PEL: Exposure to airborne crystalline silica shall not exceed an 8 hour time weighted average limit
as stated in 29 CFR 1910.1000, Table-Z-1-A Air contaminants, specifically: Silica, Crystalline Quartz
(Respirable) 0.1 MG/M3. ACGIH TLV-TWA; 01 MG/M3. NIOSH Maximum permissible conc. 0.05 MG/M3,
10 hour workday, 40 hour week. This product contains the following substances known to the State of
California to cause cancer, birth defects, or other reproductive hazards: Benzene, Toluene, Crystalline
Silica.

12. Ecological Information

General Ecological Information: Toxic to aquatic life with long lasting effects.
Persistence and Degradability: No data available
Bio Accumulative Potential: No data available
Mobility in Soil: No data available

13. Disposal Considerations

Waste Disposal Method: Dispose of as unused product. This material may be burned in a chemical incinerator equipped
with an afterburner and scrubber. Observe all federal, state, and local environmental regulations.
Contact a licensed professional waste disposal service to dispose of this material.
 SLIPDOCTORS ULTRA GRIP PART A – SAFETY DATA SHEET 03/13/2023 PAGE 5 OF 5
14. Transport Information

LAND TRANSPORT (US DOT): 1 Gallon: Limited Quantity when shipped in the United States of America
DOT Proper Shipping Name: 5 Gallon Pail: UN1263, Paint Related Material, 3, PG III

MARINE TRANSPORT: UN1263, Paint Related Material, 3 PG III

IMDG Shipping: The marine pollutant mark is not required when transported in sizes of <5 L or <5 kg (per container)

AIR TRANSPORT (ICAO/IATA): UN1263, Paint Related Material, 3 PG III

IATA Shipping Name:

15. Regulatory Information

EPA SARA (Superfund Amendments and Reauthorization Act of 1986) Lists

CAS # Hazardous Components S. 302 (EHS) S. 304 RQ S. 313 (TRI)

(Chemical Name)

14808-60-7 Silicon Dioxide No No No

25068-38-6 Epoxy Resin No No No
1344-28-1 Aluminum oxide No No Yes
13463-67-7 Titanium dioxide No No No
107-98-2 2-Propanol, 1-Methoxy- No No No
1333-86-4 Black Pigment No No No

All components in this product are listed in the TSCA Inventory List.
V.O.C. .61 lbs (74 GMS/L)

16. Other Information

Revision Date: 3/13/2023

Additional Information About This Product:

Hazardous Material Information System III (U.S.A)

Health: 2
Flammability: 3
Reactivity: 0
Personal Protection: *

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant
hazards or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910.1200, the preparer may choose to provide them.
HMIS® ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings
Association (NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.

The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this information is to
draw attention to the health and safety aspects concerning the products supplied by SlipDoctors and to recommend precautionary measures
for the storage and handling of the products. No warranty or guarantee is given in respect of the properties of the products. No liability can
be accepted for any failure to observe the precautionary measures described in this data sheet or for any misuse of the products.
 ULTRA GRIP
PART B – LOW TEMP CURE
SAFETY DATA SHEET

Page 1 – 3/14/2023
1. Product and Company Identification

Product Name: ULTRA GRIP – PART B HARDENER LOW TEMP CURE (QUART)

Company Name: SlipDoctors

2101 Midway Road, Suite 350
Carrollton, TX 75006

Phone Number: +972-999-9998

Emergency Contact: Emergencies Involving Spills, Leaks, Fires, Exposures, or Accidents

CHEMTREC: (800) 424-9300

2. Hazards Identification

Skin Corrosion/Irritation, Category 1B

Skin Sensitization, Category 1
Serious Eye Damage/Eye Irritation, Category 1
Germ Cell Mutagenicity – Category 2
Acute Toxicity: Oral, Category 4
Aquatic Toxicity (Acute), Category 1
Aquatic Toxicity (Chronic), Category 1

GHS Signal Word Danger

GHS Hazard Phrases: H302 – Harmful if swallowed.
H314 - Causes severe skin burns and eye damage.
H361 – Suspected of damaging fertility or the unborn child.
H411 – Toxic to aquatic life with long lasting effects.
GHS Precaution Phrases: P202 – Do not handle until all safety precautions have been read and understood.
P260 - Do not breathe dust/fume/gas/mist/vapors/spray.
P264 - Wash hands thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P273 – Avoid release to the environment.
P280 - Wear protective gloves/protective clothing/eye protection/face protection.
P281 – Use personal protective equipment as required.
GHS Response Phrases: P301+330+331 – IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Get medical aid.
P303+361+353 - IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse skin
with water/shower.
P304+340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Get medical attention.
P305+351+338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing.
P332+313 - If skin irritation occurs, get medical advice/attention.
P337+313 - If eye irritation persists, get medical advice/attention.
P370+378 - In case of fire, use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam.
GHS Storage and P403+235 - Store in cool/well-ventilated place.
Disposal Phrases: Contact a licensed professional waste disposal service to dispose of this material.
Potential Health Effects: Chronic inhalation may cause effects similar to those of acute inhalation.
Inhalation: May be harmful if inhaled. Material is extremely destructive to the tissue of the mucous membranes and
SLIPDOCTORS ULTRA GRIP PART B-LOW TEMP – SAFETY DATA SHEET 03/14/2023 PAGE 2 OF 5

upper respiratory tract.

Skin Contact: May be harmful if absorbed through the skin. Causes skin burns.
Eye Contact: Causes eye burns.
Ingestion: May be harmful if swallowed.

3. Composition/Information on Ingredients

CAS # Hazardous Components (Chemical Name) Concentration

1477-55-0 Epoxy Amine Resin 60.0 - 70.0 %

84852-15-3 Phenol, 4-nonyl-, branched 25.0 - 35.0%

4. First Aid Measures

Emergency and First Aid Procedures:

In Case of Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxygen. Remove from exposure and
move to fresh air immediately. Get medical aid.
In case of Skin Contact: Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and
shoes. Wash clothing before reuse. If skin irritation occurs, get medical advice/attention.
In Case of Eye Contact: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower
eyelids. Get medical aid immediately.
In Case of Ingestion: Never give anything by mouth to an unconscious person. Rinse mouth with water. Do NOT
induce vomiting. Get medical aid.
Note to Physician: Consult a physician. Show this safety data sheet to the doctor in attendance. Move out of
dangerous area. Treat symptomatically and supportively.

5. Fire Fighting Measures

Suitable Extinguishing Use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam. For large fires, apply water from far as
Media: possible. Use very large quantities (flooding) of water applied as a mist or spray; solid streams of water may be
ineffective. Cool all affected containers with flooding quantities of water.
Fire Fighting Use water spray to cool unopened containers. Protective Equipment: Wear self-contained breathing apparatus and
Instructions: protective clothing to prevent contact with skin and eyes. Specific Hazard(s): Flammable Liquid. Emits toxic fumes
under fire conditions. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or
combustion. Use water spray to keep fire-exposed containers cool. Flammable liquid and vapor. Vapors are heavier
than air and may travel to a source of ignition and flash back. Vapors can spread along the ground and collect in low
or confined areas. This liquid floats on water and may travel to a source of ignition and spread fire. May accumulate
static electricity.
Flammable Properties Vapor may travel considerable distance to source of ignition and flash back. Container explosion may occur under
and Hazards: fire conditions. Forms explosive mixtures in air. Wear self- contained breathing apparatus for fire fighting if
necessary.

6. Accidental Release Measures

Steps to be Taken in Personal Precautions. Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate
Case Material is ventilation. Evacuate personnel to safe areas. Environmental precautions: do not let product enter drains. Soak up
inert absorbent material and dispose of hazardous waste. Keep in suitable, closed containers for deposal.
Released or Spilled:

7. Handling and Storage

Precautions to be Avoid inhalation of vapor mist. Normal measures for preventive fire protection.
Taken in Handling:
Precautions to be Keep container tightly closed in a dry and well-ventilated place. Containers that are opened must be carefully
Taken in Storage: resealed and kept upright to prevent leakage.
SLIPDOCTORS ULTRA GRIP PART B-LOW TEMP – SAFETY DATA SHEET 03/14/2023 PAGE 3 OF 5

8. Exposure Controls/Personal Protection

CAS # Partial Chemical Name OSHA TWA ACGIH TWA

1477-55-0 Epoxy Amine Resin N/A N/A
84852-15-3 Phenol, 4-nonyl-, branched N/A N/A

Respiratory Equipment For nuisance exposures use type P95 (US) or type P1 (EU EN 143) particle respirator. For higher level protection
(Specify Type): use type OV/AG/P99 (US) or type ABEK-P2 (EU EN 143) respirator cartridges. Use respirators and components
tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Where risk
assessment shows air-purifying respirators are appropriate use a full-face respirator with multi- purpose
combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls.
Eye Protection: Safety glasses with side shield. For a higher degree of protection, wear chemical splash goggles.
Protective Gloves: Wear appropriate protective gloves to prevent skin exposure, such as butyl rubber or nitrile rubber. Wear
appropriate protective clothing to prevent skin exposure.
Other Protective Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.
Clothing:
Engineering Controls: Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible
exposure limits.
Work, Hygienic, Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the
Maintenance Practices: end of workday. Wash thoroughly after handling. Wash contaminated clothing before reuse.

9. Physical and Chemical Properties

Physical States: [ ] Gas [ X ] Liquid [ ] Solid

Flash Point: >250°F
Boiling Point: >245°F
Explosive Limits: LEL: N/A UEL: N/A
Weight Per Gallon: 8.34 + .3
Vapor Pressure (mm Hg): N/A
Vapor Density: N/A
Evaporation Rate: N/A
Percent Volatile: 0

10. Stability and Reactivity

Stability: Unstable [ ] Stable [ X ] No data available.

Conditions to Avoid: Heat, flames, and sparks

Instability:
Incompatibility – Materials to Avoid: Strong oxidizing agents, acids.
Hazardous Decomposition or Byproducts: Formed under fire conditions. Carbon oxides, nitrogen oxides (NOx)
Possibility of Hazardous Reactions: Will occur [ ] Will not occur [ X ]
Conditions to Avoid – Hazardous Reactions: No data available

11. Toxicological Information

Toxicological Information: No information found.

Irritation or Corrosion: Causes severe skin burns and eye damage.
Carcinogenicity/Other Information: IARC: No component of this product presents at levels greater than or possible or confirmed human
carcinogen by IARC. equal to 0.1% is identified as probable, possible or confirmed human carcinogen
by IARC. ACGIH: No component of this product present at levels greater than or equal to 0.1% is
identified as a carcinogen or potential carcinogen by ACGIH. NTP: No component of this product
present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by
NTP. OSHA: No component of this product present at levels greater than or equal to 0.1% is identified
as a carcinogen or potential carcinogen by OSHA.
SLIPDOCTORS ULTRA GRIP PART B-LOW TEMP – SAFETY DATA SHEET 03/14/2023 PAGE 4 OF 5

12. Ecological Information

Persistence and Degradability: No data available

Bio accumulative Potential: No data available
Toxic to aquatic life with long lasting effects.

13. Disposal Considerations

Dispose of as unused product. This material may be burned in a chemical incinerator equipped
Waste Disposal Method: with an afterburner and scrubber. Observe all federal, state, and local environmental
regulations. Contact a licensed professional waste disposal service to dispose of this material.

14. Transport Information

LAND TRANSPORT (US DOT): Limited Quantity - Used for 1 gallon and quart containers when shipped in the United States of America
DOT Proper Shipping Name: UN3066, Paint Related Material, 8, PG III (sizes larger than 1 gallon)

IMDG Shipping Name: UN3066, Paint Related Material, 8, PG III

The marine pollutant mark is not required when transported in sizes of <5 L or < 5 kg (per container)

AIR TRANSPORT (ICAO/IATA): UN3066, Paint Related Material, 8, PG III

IATA Shipping Name:

15. Regulatory Information

EPA SARA (Superfund Amendments and Reauthorization Act of 1986) Lists

CAS # Hazardous Components S. 302 (EHS) S. 304 RQ S. 313 (TRI)

(Chemical Name)

1477-55-0 Epoxy Amine Resin No No No

84852-15-3 Phenol, 4-nonyl-, branched No No No
All components in this product are listed in the TSCA Inventory List.

V.O.C. (mixed): .61 LBS/GL (74 GMS/L)

 SLIPDOCTORS ULTRA GRIP PART B-LOW TEMP – SAFETY DATA SHEET 03/14/2023 PAGE 5 OF 5

16. Other Information

Revision Date: 3/14/2023

Additional Information About this Product:

Hazardous Material Information System III (U.S.A)

Health: 3
Flammability: 1
Reactivity: 0
Personal Protection: *

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards
or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910. 1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association
(NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.

The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this information is to draw
attention to the health and safety aspects concerning the products supplied by SlipDoctors and to recommend precautionary measures for the
storage and handling of the products. No warranty or guarantee is given in respect of the properties of the products. No liability can be
accepted for any failure to observe the precautionary measures described in this data sheet or for any misuse of the products.
SLIPDOCTORS ULTRA GRIP PART B LOW TEMP CURE – SAFETY DATA SHEET 03/14/2023 PAGE 6 OF 5
 ULTRA GRIP
PART B – REGULAR CURE
SAFETY DATA SHEET

Page 1 – 3/16/2023
Product Name: ULTRA GRIP – PART B HARDENER REGULAR CURE (QUART)

Company Name: SlipDoctors

2101 Midway Road, Suite 350
Carrollton, TX 75006

Phone Number: +972-999-9998

Emergency Contact: Emergencies Involving Spills, Leaks, Fires, Exposures, or Accidents

CHEMTREC: (800) 424-9300

2. Hazards Identification
Skin Corrosion/Irritation, Category 1B
Skin Sensitization, Category 1
Serious Eye Damage/Eye Irritation, Category 1
Germ Cell Mutagenicity – Category 2
Acute Toxicity: Oral, Category 4
Aquatic Toxicity (Acute), Category 1
Aquatic Toxicity (Chronic), Category 1

GHS Signal Word Danger

GHS Hazard Phrases: H302 – Harmful if swallowed.
H314 - Causes severe skin burns and eye damage.
H361 – Suspected of damaging fertility or the unborn child.
H411 – Toxic to aquatic life with long lasting effects.
GHS Precaution Phrases: P202 – Do not handle until all safety precautions have been read and understood.
P260 - Do not breathe dust/fume/gas/mist/vapors/spray.
P264 - Wash hands thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P273 – Avoid release to the environment.
P280 - Wear protective gloves/protective clothing/eye protection/face protection.
P281 – Use personal protective equipment as required.
GHS Response Phrases: P301+330+331 – IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Get medical aid.
P303+361+353 - IF ON SKIN (or hair): Remove/take off immediately all contaminated clothing. Rinse skin with
water/shower.
P304+340 - IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
Get medical attention.
P305+351+338 - IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present
and easy to do. Continue rinsing.
P332+313 – If skin irritation occurs, get medical advice/attention.
P337+313 - If eye irritation persists, get medical advice/attention.
P370+378 - In case of fire, use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam.
GHS Storage and P403+235 - Store in cool/well-ventilated place.
Disposal Phrases: Contact a licensed professional waste disposal service to dispose of this material.
Potential Health Effects: Chronic inhalation may cause effects similar to those of acute inhalation.
Inhalation: May be harmful if inhaled. Material is extremely destructive to the tissue of the mucous membranes and upper
SLIPDOCTORS ULTRA GRIP PART B-REGULAR – SAFETY DATA SHEET 03/16/2023 PAGE 2 OF 5

respiratory tract.
Skin Contact: May be harmful if absorbed through the skin. Causes skin burns.
Eye Contact: Causes eye burns.
Ingestion: May be harmful if swallowed.

3. Composition/Information on Ingredients

CAS # Hazardous Components (Chemical Name) Concentration

Proprietary Epoxy Amine Resin 55.0 - 65.0 %

84852-15-3 Phenol, 4-nonyl-, branched 35.0 - 45.0%

4. First Aid Measures

Emergency and First Aid Procedures:

In Case of Inhalation: If inhaled, remove to fresh air. If breathing is difficult, give oxygen. Remove from exposure and
move to fresh air immediately. Get medical aid.
In case of Skin Contact: Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and
shoes. Wash clothing before reuse. If skin irritation occurs, get medical advice/attention.
In Case of Eye Contact: Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower
eyelids. Get medical aid immediately.
In Case of Ingestion: Never give anything by mouth to an unconscious person. Rinse mouth with water. Do NOT
induce vomiting. Get medical aid.
Note to Physician: Consult a physician. Show this safety data sheet to the doctor in attendance. Move out of
dangerous area. Treat symptomatically and supportively.

5. Fire Fighting Measures

Suitable Extinguishing Use water spray, dry chemical, carbon dioxide, or alcohol-resistant foam. For large fires, apply water from far as
Media: possible. Use very large quantities (flooding) of water applied as a mist or spray; solid streams of water may be
ineffective. Cool all affected containers with flooding quantities of water.
Fire Fighting Use water spray to cool unopened containers. Protective Equipment: Wear self-contained breathing apparatus and
Instructions: protective clothing to prevent contact with skin and eyes. Specific Hazard(s): Flammable Liquid. Emits toxic fumes
under fire conditions. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or
combustion. Use water spray to keep fire-exposed containers cool. Flammable liquid and vapor. Vapors are heavier
than air and may travel to a source of ignition and flash back. Vapors can spread along the ground and collect in low
or confined areas. This liquid floats on water and may travel to a source of ignition and spread fire. May accumulate
static electricity.
Flammable Properties Vapor may travel considerable distance to source of ignition and flash back. Container explosion may occur under
and Hazards: fire conditions. Forms explosive mixtures in air. Wear self- contained breathing apparatus for fire fighting if
necessary.

6. Accidental Release Measures

Steps to be Taken in Personal Precautions. Use personal protective equipment. Avoid breathing vapors, mist or gas. Ensure adequate
Case Material is ventilation. Evacuate personnel to safe areas. Environmental precautions: do not let product enter drains. Soak up
inert absorbent material and dispose of hazardous waste. Keep in suitable, closed containers for deposal.
Released or Spilled:

7. Handling and Storage

Precautions to be Avoid inhalation of vapor mist. Normal measures for preventive fire protection.
Taken in Handling:
Precautions to be Keep container tightly closed in a dry and well-ventilated place. Containers that are opened must be carefully
Taken in Storage: resealed and kept upright to prevent leakage.
SLIPDOCTORS ULTRA GRIP PART B-REGULAR – SAFETY DATA SHEET 03/16/2023 PAGE 3 OF 5

8. Exposure Controls/Personal Protection

CAS # Partial Chemical Name OSHA TWA ACGIH TWA

Proprietary Epoxy Amine Resin N/A N/A
84852-15-3 Phenol, 4-nonyl-, branched N/A N/A

Respiratory Equipment For nuisance exposures use type P95 (US) or type P1 (EU EN 143) particle respirator. For higher level protection
(Specify Type): use type OV/AG/P99 (US) or type ABEK-P2 (EU EN 143) respirator cartridges. Use respirators and components
tested and approved under appropriate government standards such as NIOSH (US) or CEN (EU). Where risk
assessment shows air-purifying respirators are appropriate use a full-face respirator with multi- purpose
combination (US) or type ABEK (EN 14387) respirator cartridges as a backup to engineering controls.
Eye Protection: Safety glasses with side shield. For a higher degree of protection, wear chemical splash goggles.
Protective Gloves: Wear appropriate protective gloves to prevent skin exposure, such as butyl rubber or nitrile rubber. Wear
appropriate protective clothing to prevent skin exposure.
Other Protective Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.
Clothing:
Engineering Controls: Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible
exposure limits.
Work, Hygienic, Handle in accordance with good industrial hygiene and safety practice. Wash hands before breaks and at the
Maintenance Practices: end of workday. Wash thoroughly after handling. Wash contaminated clothing before reuse.

9. Physical and Chemical Properties

Physical States: [ ] Gas [ X ] Liquid [ ] Solid

Flash Point: >260°F
Boiling Point: >245°F
Explosive Limits: LEL: N/A UEL: N/A
Weight Per Gallon: 8.25 + .3
Vapor Pressure (mm Hg): N/A
Vapor Density: N/A
Evaporation Rate: N/A
Percent Volatile: 0

10. Stability and Reactivity

Stability: Unstable [ ] Stable [ X ] No data available.

Conditions to Avoid: Heat, flames, and sparks

Instability:
Incompatibility – Materials to Avoid: Strong oxidizing agents, acids.
Hazardous Decomposition or Byproducts: Formed under fire conditions. Carbon oxides, nitrogen oxides (NOx)
Possibility of Hazardous Reactions: Will occur [ ] Will not occur [ X ]
Conditions to Avoid – Hazardous Reactions: No data available

11. Toxicological Information

Toxicological Information: No information found.

Irritation or Corrosion: Causes severe skin burns and eye damage.
Carcinogenicity/Other Information: IARC: No component of this product presents at levels greater than or possible or confirmed human
carcinogen by IARC. equal to 0.1% is identified as probable, possible or confirmed human carcinogen
by IARC. ACGIH: No component of this product present at levels greater than or equal to 0.1% is
identified as a carcinogen or potential carcinogen by ACGIH. NTP: No component of this product
present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by
NTP. OSHA: No component of this product present at levels greater than or equal to 0.1% is identified
as a carcinogen or potential carcinogen by OSHA.
SLIPDOCTORS ULTRA GRIP PART B-REGULAR – SAFETY DATA SHEET 03/16/2023 PAGE 4 OF 5

12. Ecological Information

Persistence and Degradability: No data available

Bio accumulative Potential: No data available
Toxic to aquatic life with long lasting effects.

13. Disposal Considerations

Dispose of as unused product. This material may be burned in a chemical incinerator equipped
Waste Disposal Method: with an afterburner and scrubber. Observe all federal, state, and local environmental
regulations. Contact a licensed professional waste disposal service to dispose of this material.

14. Transport Information

LAND TRANSPORT (US DOT): Limited Quantity - Used for 1 gallon and quart containers when shipped in the United States of America
DOT Proper Shipping Name: UN3066, Paint Related Material, 8, PG III (sizes larger than 1 gallon)

IMDG Shipping Name: UN3066, Paint Related Material, 8, PG III

The marine pollutant mark is not required when transported in sizes of <5 L or < 5 kg (per container)

AIR TRANSPORT (ICAO/IATA): UN3066, Paint Related Material, 8, PG III

IATA Shipping Name:

15. Regulatory Information

EPA SARA (Superfund Amendments and Reauthorization Act of 1986) Lists

CAS # Hazardous Components S. 302 (EHS) S. 304 RQ S. 313 (TRI)

(Chemical Name)

Proprietary Epoxy Amine Resin No No No

84852-15-3 Phenol, 4-nonyl-, branched No No No
All components in this product are listed in the TSCA Inventory List.

V.O.C. (mixed): .61 LBS/GL (74 GMS/L)

SLIPDOCTORS ULTRA GRIP PART B-REGULAR – SAFETY DATA SHEET 03/16/2023 PAGE 5 OF 5

16. Other Information

Revision Date: 3/16/2023

Additional Information About this Product:

Hazardous Material Information System III (U.S.A)

Health: 3
Flammability: 1
Reactivity: 0
Personal Protection: *

Caution: HMIS® ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards
or risks Although HMIS® ratings are not required on MSDSs under 29 CFR 1910. 1200, the preparer may choose to provide them. HMIS®
ratings are to be used with a fully implemented HMIS® program. HMIS® is a registered mark of the National Paint & Coatings Association
(NPCA). HMIS® materials may be purchased exclusively from J. J. Keller (800) 327-6868.

The information contained in this data sheet is based on present scientific and technical knowledge. The purpose of this information is to
draw attention to the health and safety aspects concerning the products supplied by SlipDoctors. and to recommend precautionary
measures for the storage and handling of the products. No warranty or guarantee is given in respect of the properties of the products. No
liability can be accepted for any failure to observe the precautionary measures described in this data sheet or for any misuse of the
products.
SLIPDOCTORS ULTRA GRIP PART B-REGULAR – SAFETY DATA SHEET 03/16/2023 PAGE 6 OF 5