Commisioning Error Codes BT300

Supplement

Sensors and Systems

for Combustion Engineering
 Table of Contents

Table of Contents

1 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.1 Validity of these Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 LIST OF FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3 ASSIGNMENT OF CONFIGURATION FAULT 107 . . . . . . . . . . . . . . . . . . 12

4 ASSIGNMENT OF INTERNAL FAULT 999. . . . . . . . . . . . . . . . . . . . . . . . . 13

5 ASSIGNMENT OF CO/O2 CONTROL FAULTS OR INFORMATION. . . . . 22

2
 1 General Information

1 General Information
1.1 Validity of these Instructions

This document is a supplement to the Operating Instructions for the LAMTEC BurnerTron-
icBT300 listed below.
It is only applicable together with the Operating Instructions for the affected device.
The specifications in this document refer to the software version BT300 v and higher and
UI300 v and higher. The following functionalitie ares not available with software versions <3.0.
• CO/O2 control
• Applications with frequency converter functions (VSM)

This document is applicable for the following devices:

BurnerTronic
– BT320
– BT330
– BT331
– BT340
– BT341

3
2 List of Fault Codes

2 List of Fault Codes

Fault TRD EN67 Description D1 D2
Code P301=0 P301=2
P328>0 P328>0
0 0 0 Unknown fault (internal error)

1 0 3 Flame fault

2 0 0 Parasitic light detected.

3 0 3 Flame blow-off during ignition

4 1 1 Flame blow-off during operation

5 0 3 Flame signal does not appear during the first safety time.

6 0 3 Flame signal extinguishes during stabilization time.

7 0 3 Flame signal extinguishes during first safety time.

8 0 0 Flame signal extinguishes during the second safety time.

9 0 0 Flame signal does not appear during the safety time.

10 0 0 Flame signal extinguishes during the safety time.

11 0 0 Monitoring for parasitic light does not last the required 5 sec-
onds.

13 1 0 Main flame appears during ignition.

103 0 0 Miscellaneous data invalid.

105 Optional 0 Curve data are invalid or not available. Curve set /
Fuel number

106 0 0 Difference in parameter value between HP and UP. Parameter

No.
Possible cause of error:
You have uploaded a normal data set (unprotected) and an
error occured during the data transfer. The dataset was not
save correctly.

4
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
107 0 0 Configuration is not valid.
See chapter 3 Assignment of Configuration fault 107.
120 1 1 Different operation modes on both controllers

121 0 0 Correction is out of range. Channel

141 0 0 Variation of speed feedback is to big. Channel

Parameter set is based on an old, invalid factory setting.
Update the factory setting of the BT300.
151 Optional 3 Recirculation damper is still OPEN 240 s after recirculation Channel
release is OFF.

170 0 0 Short circuit of LDR flame detector

191 1 1 First monitoring band exceeded for too long: channel Channel

201 1 1 First monitoring band fall short for too long: channel Channel

211 0 0 Second monitoringband exceeded for too long: channel Channel

221 0 0 Second monitoring band fall short for too long: channel Channel

231 Optional 3 Fuel/air ratio control is blocked: channel Channel

241 0 0 Actuator does not move, i.e. no position feedback. Channel Direction:
P2=
0 backward,
1 forward
If this indication is shown, the monitoring of fault 271 is
demaged.
251 0 0 Actuator cannot find reference position. Channel
Direction:
0 backward
1 forward
Check the flap’s smooth-running to reference position.
261 Optional 3 Actuator returns invalid position (difference to target position Channel
too large)

271 Optional 3 Actuator feedback remains constantly for too long, even Channel
when actuator has moved.

5
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
281 1 1 Feedback signal of at least 1 actuator is incorrect channel
To identify the actuator’s direction of rotation two pulse form
signals, offset 90 degrees, are returned by the actuator. If
fault 281 occurs, these signals are not identified correctly.
Cause of error:
– Back lash
– actuator 0,8 Nm:
external torque clockwise >0,2 Nm
– actuator 9 Nm:
external torque clockwise >1 Nm
291 Optional 3 Actuator does not reach the final position, because of mixed- Channel
up detection.
Actuators are mixed up while reconnecting. The test for rec-
ognising this fault is described in the manual of the BT300 –
print no. DLT1201.
At least one actuator does not reach it’s test position:
– 2 actuators are mixed up
– another problem inhibits the actuator to reach it’s testposi-
tion.
320 1 1 Open broken wire at firing rate input

321 1 1 Open broken wire at feedback channel: channel Channel

351 1 1 Invalid fuel change while burner is running

352 Optional 3 Invalid combination of fuel signals (no signals)

353 Optional 3 Invalid combination of fuel signals (several signals)

360 0 0 Air deficiency causes a fault shut-downf by O2 trim.

362 0 0 Fault shut-down due to a missing burner maintenance

363 1 1 Smallest valid O2 value deceeded.

371 0 0 Output for internal firing-rate is defective.

372 0 0 Difference of the burner firing-rate values between main pro-

cessor and watchdog processor is too large.

381 0 0 Deviation between main processor and watchdog controller Correction

is too large. channel

6
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
391 0 0 Curve set has changed during programming.

393 0 0 Emergency shut-down activated.

394 0 0 Burner ON/OFF signal from the user interface turned off
unexpectedly.

451 1 1 Being operating mode for ignition not all channels are in igni- Channel
tion position .

600 0 0 Program monitoring time (FAT) exceeded. indication

number

601 0 0 Failure during leakage test: gas pressure still active.

602 0 0 Failure during leakage test: no gas pressure detected.

603 0 0 Manual venting of the gas line required!

606 0 0 CPI/POC signal in unexpected state

607 1 1 Invalid drop of ignition position acknowledgement

608 1 *1) 1 *1) Invalid drop of the boiler safety interlock chain

609 1 *1) 1 *1) Invalid drop of the gas safety interlock chain

610 Optional 3 *1) Invalid drop of the oil safety interlock chain
*1)

611 Optional 3 Gas pressure too low.

613 0 0 Air pressure signal is missing.

617 1 1 Permanent pilot flame extinguishes during operation.

624 Optional 3 Oil pressure too low.

711 0 0 Invalid change of the operation mode

*1) The system will be restarted not before the condition of the fault is eliminated( i.e. the dropped safety inter-
lock chain (SIC) or the low voltage) .

7
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
713 0 0 Invalid signal combination at input terminals during operating
mode BURNER OFF

714 0 0 Invalid signal combination at input terminals during operating

mode BURNER READY

715 0 0 Invalid signal combination at input terminals during operating

mode PRE-VENTILATION

716 0 0 Invalid signal combination at input terminals during operating

mode IGNITION POSITION

717 0 0 Invalid signal combination at input terminals during operating

mode IGNITION

719 0 0 Fuel valves are open for too long without a flame.

720 0 0 Ignition transformer activated too long.

721 0 0 Ignition valve openes for too long.

722 0 0 Fuel valves open in maintenance mode.

723 0 0 Ignition process needs too much time.

724 0 0 Gas valve open with fuel oil.

725 0 0 Oil valves are open while gas is selected.

727 0 0 Main gas 1 opens unexpectedly.

728 0 0 All three gas valves open for too long.

729 0 0 Ignition process lasts for too long (without pilot burner).

730 0 0 Maintenance mode without pilot burner

731 0 0 Ignition valve opens without pilot burner.

732 0 0 Invalid signal combination at input terminals during opera-

tion.

8
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
734 0 0 Pre-ventilation period not respected.

739 0 0 Leakage test: Main gas valve 2 opens for too long.

740 0 0 Leakage test: Main gas valve 1 leaky.

741 0 0 Leakage test: Main gas valve 1 opens for too long.

742 0 0 Leakage test: Main gas valve 2 leaky.

743 0 0 Flame monitoring: Flame burns for too long after shutdown.

745 0 0 Program monitoring time exceeded.

746 0 0 Solenoid valve cannot be switched off.

747 0 0 Leakage test: Venting into the burner is not allowed.

751 Optional 3 The bus-card runs into time-out.

759 0 0 BT300 leavs SETTING mode automatically after 24 hours.

763 0 0 Different curve selection on main processor and watchdog

processor

764 1 1 CO-controller - internal curve set failure Curve set

800 0 0 Parameter defective. Parameter

No.

801 0 0 Channel control mode is inconsistent between main proces- Channel

sor and watchdog processor (fatal error, no automatic restart
possible).

802 1 1 Integration of a channel into the fuel/air ratio control takes Channel
too long (only one automatic restart possible).

803 0 0 Channel is out of 1st monitoring band for too long. Channel

804 0 0 Channel mode of the fuel/air ratio control does not match to Channel
the activation type.

9
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
805 0 0 Directly controlled channel runs to an invalid position, i.e. a Channel +
channel that is not deactivated or controlled by fuel/air ratio set point
control. position

806 0 0 Implausible channel setpoint of the main controller Channel +

set point
position +
actual value
+ program-
ming toler-
ance

807 1 1 Timeout of LSB message (message no. = parameter).

Possible cause of error :
– connection between VMS/LCM GND and protective
conductor PE
– acknowledgment of speed change too fast / fault of VMS
889 0 0 The gap between two remote fault releases is too short.
EN 14459 allows only 4 remote fault resets every15 min.
Fault elease is monitored by remote control software,
LAMTEC SYSTEM BUS and field bus. Exceeding the num-
ber of fault releases causes the fault shot-down H889 and
further remote fault releases are ignored. After a delay time
another remote fault release is possible.
The fault shut-down H889 also occures, if fault release is
sent without any reason.
A reset by terminal is always possible.
921 0 0 Relay driver self-test: Output oil valve defect.

922 0 0 Relay driver self-test: Output ignition transformer defect.

923 0 0 Relay driver self-test: Output gas valve 1 defect.

924 0 0 Relay driver self-test: Output gas valve 2 defect.

925 0 0 Relay driver self-test: Output ignition transformer defect.

928 0 0 Relay driver self-test: Output terminal 41 for oil pump defec-
tive.

929 0 0 Relay driver self-test: Output fan defect.

985 0 0 VSM diagnosis error

Possible cause of error:
BurnerTronic expects a VSM module but the exchange of
diagnosis data with the module fails.

10
2 List of Fault Codes

Fault TRD EN67 Description D1 D2

Code P301=0 P301=2
P328>0 P328>0
986 0 0 Dynamic range test recognizes an invalid feedback. Channel Actual value

987 0 0 Change-over during staged operation takes too much time.

988 0 0 Fuel selection relay in the DFM is defective or inconsistent

feedback from DFM.

989 0 0 Plausibility test of actuator feedback in programmed curve

failed.

990 Optional 3 Power failure

*1)

996 0 0 Secure parameter writing could not be finished. Device is

blocked.

999 Please note the diagnostic codes D1 and D2 and send them
to [email protected] and replace the device.
See chapter 4 Assignment of internal fault 999.

*1) The system will be restarted not before the condition of the fault is eliminated( i.e. the dropped safety inter-
lock chain (SIC) or the low voltage) .

11
3 Assignment of Configuration fault 107

3 Assignment of Configuration fault 107

D1 Description
1 Too many channels activated.
2 No channel at all configured.
3 Permanent ignition burner configured (parameter 302, 303), but no ignition flame monitoring device present
(parameter 800).
6 Prepurge suppression via external signal not implemented.
7 Fuel change via OFF and an unlimited post ventilation configured.
8 Prepurge time is smaller than minimal prepurge time.
9 For stages oil mode at least one of the actuators must be set to air duct.
13 Australian flame monitoring (2 main flame scanner) configured, but no ignition flame monitoring device.
18 Standby operation at BT300 not allowed.
19 Invalid fuel change selected.
20 BT300 only with separate ignition point.
21 "Ignition with fan ON", only useful with pure oil devices.
23 3-staged operation only works without ignition burner.
24 Permanent operation not allowed.
25 Fuel change not allowed.
26 Too many channels.
27 Staged oil burners need an air channel.
28 There is an invalid function configured for a channel.
30 Multiple terminals defined for one signal, terminal configuration invalid.
31 No output terminal for fan or transformer available.
32 Necessary outputs for operation with oil not available (oil pump or oil valve).
33 Necessary outputs for operation with gas not available (gas valve).
34 An output terminal is needed for the ignition valve, but is not available in the actual terminal configuration.
40 No input terminal for the air pressure monitor available.
41 No input terminal for the oil safety chain available (oil pressure min will not be monitored directly, because it can be
included in the safety chain).
42 No input terminal for the gas safety chain or minimum gas pressure available.
43 The feedback line for the fuel selection is not mapped, but is required.

12
4 Assignment of internal fault 999

4 Assignment of internal fault 999

D1 D2 Description
10 return value of m_PwrOn_uiInitAPI() m_PwrOn_uiInitAPI() failed.
20 0 CRC32 check of ROM failed.
21 0 Cyclic CRC32 check of ROM during runtime failed.
22 Erroneous State State machine for CRC32 check during runtime ran into an invalid state.
40 0 m_PwrOn_bLoadEEPROM() failed.
92 Vorgabe ATTENTION, wrong number in the wrong module, is reported from
hchactab, if the control tables are not correct.

200 0 Last destination element is no member of sER.sP

201 0 Last destination element is no member of sER.sM
202 0 Last destination element is no member of sER.sC
203 0 Last destination element is no member of sER.sH
204 0 Destination is no member of sER.sX
210 sEECtrl.sChk.uiReadStartAddr Refresh cycle timeout expired
211 sEECtrl.sChk.uiReadStartAddr Uncorrectable error in EEPROM block
212 sEECtrl.eSeq_State Invalid state
215 uiEEFaultAddr Uncorrectable error in Parameter Set
216 uiEEFaultAddr Uncorrectable error in Miscell-Data
217 uiEEFaultAddr Uncorrectable error in Curve Set
220 0 pucDst == NULL
222 uiEEStartAddr Invalid EEPROM address
240 uiEEStartAddr Write beyond end of safety area!
241 uiEEStartAddr Start address in safety area is no multiple of 3
242 uiEEStartAddr Write beyond end of non-safety area!
243 uiEEStartAddr Start address is in reserved area!
244 ulReqFIFOSpace Not enough FIFO space
250 (ulong32)pucDst Readback error while refreshing - possibly defective RAM cell

300 0 Timout sICom.uiRxLiveTimer expired

301 0 Timout sICom.uiTxLiveTimer expired
350 0 Timeout sICom.uixLiveTimer expired
360 0 Timeout waiting for acknowledgement of DUAL_BEF_CHECK_PARAM
361 0 FIFO full!
380 uiBPP_HPPunktNr Error when calling uiPutPunkt()
381 0 Command leakage test occured while BM_FAT_KALTCHECK
382 0 Timeout during cyclical parameter comparison
383 uiBCP_AnzParam[0] DUAL_BEF_CHANGE_PARAM1: invalid value in the receive buffer
384 uiBCP_AnzParam[1] DUAL_BEF_CHANGE_PARAM2: invalid value in the receive buffer
385 sRx.Buffer.ui[ucRxOK-1][uiSTART- Cyclic parameter verification: different parameters between HP and UP!
BEF+47]
386 uiParaIdx PowerOn parameter verification: different parameters between HP and UP!
410 sIO.sIn.ulInputsN Detected positive half-wave on terminal input!
411 input status received from UP Different input status between controllers

13
4 Assignment of internal fault 999

D1 D2 Description
412 0 The readback input of the fuel selection relais contacts in the dual fuel is
invalid. DFM probably defect.
420 uil Input status of digital input on HP and UP is inconsistent (>20ms)
430 ucPin2Test Pin short circuit test detected an error! Currently tested pin not configurated
as output or is stuck at 1
431 ucPin2Test Pin short circuit test detected an error! Short-circuit between pins, pull-up of
input stage defective or pin is externally stuck at 0
440 0 sIO.sIn.uiTestSignalTimeout expired
450 0 Main power relay (K2) does not switch correctly to off when out of power.
451 ucRelay Relay does not switch correctly, when relay power is enabled (for details
see enum teRelais)

0 Relay PWR
1 Relay oilpump
2 Relay bowler
3 Relay V1
4 Relay V2
5 Relay V3
6 Relay ignition trafnsrormer
7 Relay alarm
8 Relay DFM
460 uiFaultParam Failure of relais power switching or readback of relay coils of K1 or K2Par-
am2: Bit 0 is set if readback line of K1 is erroneous, Bit 1 is set if readback
line of K2 is erroneous

0 Relay PWR
1 Relay oilpump
2 Relay bowler
3 Relay V1
4 Relay V2
5 Relay V3
6 Relay ignition trafnsrormer
7 Relay alarm
8 Relay DFM
461 uiFaultParam Readback status of relay K1 or K2 differs from desired switching status,
relay propably defect. Param2:Bit 0: nominal state of K1Bit 1: nominal state
of K2Bit 8: state of readback line of K1Bit 9: state of readback line of K2

500 0 Timeout while waiting for end of write cycle

501 0 SLA+W has been transmitted; NO ACK has been received
502 0 SLA+R has been transmitted; NO ACK has been received
503 0 Data byte has been transmitted; NO ACK has been received
504 0 BUS error due to an illegal START or STOP condition
505 0 Arbitration lost in SLA+R/W or Data bytes
510 ulI2CStat Unknown/invalid state!

600 sSRCtrl.uiOffset Correction of defective triple in Safety RAM structure failed

610 (ulong32)pucDst Invalid destination address
620 (ulong32)puiDst Invalid destination address
630 (ulong32)pulDst Invalid destination address

700 0 CPU self-test failed

14
4 Assignment of internal fault 999

D1 D2 Description
701 sSelftest.sMngr.eState state-event-machine failed with AC_ERR
710 sSelftest.sWD.eErrorState Watchdog self-test failed
711 sSelftest.sWD.eState Invalid default case
720 Selftest.sVM.ucTest2Perform Invalid default case
721 Selftest.sVM.eErrorState Supply voltage monitor self-test failed
722 Selftest.sVM.eState Invalid default case
730 sSelftest.sRR.eErrorState Relay release circuit self-test failed
731 sSelftest.sRR.eState Invalid default case
740 sSelftest.sRPW.eErrorState Relay PWR release circuit self-test failed
741 sSelftest.sRPW.eState Invalid default case
750 0: USR-Stack, 1: IRQ-Stack Stack overflow detected
751 0 Stackaddress is NULL-Pointer
752 0 Stackaddress is NULL-Pointer

800 sWDog.ulReleasePtrn1 Trigger release patterns are invalid!

810 eFeedIndex Invalid Feed Index
820 eTriggerCtrl Invalid Trigger Mode
830 0 No valid watchdog trigger received (frequency or duty cycle invalid).

900 uiErrorCode Fault from LPC_API error handler

920 0 Invalid entry in iStoerResRam
930 uiMaskedFaultCode uiMaskedFaultCode out of range!

1200 0 Flame signal doesn't disappear during self-test.

1210 sIFD.eTestState Invalid default case
1220 sIFD.uiClock UP is missing test impulses.
1221 sIFD.uiClock Test signal duration too short
1222 sIFD.uiClock Test signal duration too short

1240 0 Detected short circuit of LDR

1250 uiADValue Circuit selftest failed, A/D value out of expected range.
1260 sLDR.eTestState Invalid default case
1270 sLDR.uiClock Test interval too long
1271 sLDR.uiClock HP released test pin too late.
1272 sLDR.uiClock HP released test pin too early.

1290 uiMyFlames XOR uiPartnerFlames Flame signals on both controllers are inconsistent
(bit 0: main flame, bit 1: ignition flame).

1300 0 Pointer to transmit buffer is NULL

1400 psActuator->ucSANumber H_SA_INTERFACE_INVALID_ACTUATOR_TYPE

1401 psActuator->ucSANumber H_SA_INTERFACE_INVALID_DIRECTION
1405 0 H_SA_INTERFACE_WRONG_RAMP_CALCULATION
1406 0 ulGradientMax <= ulGradientDesired

15
4 Assignment of internal fault 999

D1 D2 Description
1410 0 H_SA_INTERFACE_WRONG_RAMP_CALCULATION
1411 0 H_SA_INTERFACE_ERROR_TIMING
1415 psActuator->ucSANumber psActuator->ucSANumber Invalid!
1416 psActuator->ucSANumber psActuator->ucSANumber Invalid!
1420 psActuator->ucSANumber H_SA_INTERFACE_WRONG_RAMP_CALCULATION
1430 psActuator->ucSANumber H_SA_FEEDBACK_WRONG_FEEDBACK
1435 psActuator->ucSANumber H_SA_PLAUSIB_ACTUATOR_OUT_OF_RANGE
1436 psActuator->ucSANumber H_SA_PLAUSIB_SECTION_COUNT_OUT_OF_RANGE
1440 psActuator->ucSANumber H_SA_REFERENCE_SEARCH_NO_REFERENCE_FOUND
1450 psActuator->ucSANumber H_SA_STEPCALC_CALL_COUNT_OVERFLOW
1451 psActuator->ucSANumber H_SA_STEPCALC_SECTIONCOUNT_OUT_OF_RANGE
1452 psActuator->ucSANumber H_SA_STEPCALC_INVALID_DIRECTION
1453 psActuator->ucSANumber H_SA_STEPCALC_SECTIONCOUNT_OUT_OF_RANGE
1454 psActuator->ucSANumber H_SA_STEPCALC_INVALID_DIRECTION
1455 psActuator->ucSANumber H_SA_STEPCALC_WRONG_STATUS
1460 0 U_SA_INTERFACE_INVALID_ACTUATOR_TYPE
1461 0 U_SA_INTERFACE_INVALID_DIRECTION
1470 psActuator->ucSANumber U_SA_FEEDBACK_INVALID_DIRECTION
1471 psActuator->ucSANumber U_SA_FEEDBACK_INVALID_DIRECTION
1472 psActuator->ucSANumber U_SA_FEEDBACK_WRONG_FEEDBACK
1480 psActuator->ucSANumber U_SA_REFERENCE_SEARCH_INVALID_ACTUATOR_TYPE
1490 psActuator->ucSANumber psActuator->ucSANumber invalid!

1500 0 Timeout while sending ICOM command

1501 0 Timeout while waiting for ACK of ICOM command
1502 0 Timeout while waiting for end of actuator initilization
1503 0 Timeout while waiting for end of actuator initilization
1504 0 Timeout while waiting for end of actuator initilization
1505 Actuator Number HP: Invalid configuration. Parameter for Actuator Type should never be
different from 1 or 2.
2000 Unknown event, for the event handling mechanism
2001 Too many events for even queue

2100 Invalid buffer input

2101 EEProm probably defective

2200 Invalid Index for SQBLData00

2201 Invalid Index for SQBLData01
2202 Invalid Index for SQBLData02
2203 Invalid Index for SQBLData03
2204 Invalid Index for SQBLData04
2205 Invalid Index for SQBLData05
2206 Invalid Index for SQBLDataKurven
2207 Invalid Index for SQBLDataPara
2208 Invalid Index for SQBLData15

16
4 Assignment of internal fault 999

D1 D2 Description
2209 Data request for data block, but no transmission.

2300 Invalid state

2301 Invalid state
2302 Deleting curve, end of EI
2303 Invalid state
2304 Invalid state
2305 Invalid parameter number (does not exist).
2306 Invalid state (cold check)
2307 Cold check
2308 Cold check
2309 Cold check
2310 Invalid state
2350 - Cold check
2354

2400 Attempt to write to a modbus register

2401 Modbus register described

2500 Parameter with access level > 4

2600 Does not find the operating mode

2601 Transfer forbidden

2700 Deleting curve, left EI

2800 The air pressure was not droped but the burner still starts.
2801 It was opened more than one valve in the cold check.
2802 Maintenance mode on the main controller is active, but there is no mainte-
nance mode parameterized.
2803 Maintenance mode active but it is still ignite.
2804 Burner starts, while the supervisor controller is blocked.
2805 Burner starts, while no reference test was made.
2806 Vom HP gesendete Stufe für stufigen Betrieb scheint unplausibel.

2900 Program load by the timer to high

3000 All errors, for which no error number was registered

3100 Error message of a password module

3101 Error message of the password module

3200 Internal overflow, intermediate result does not fit in the variable.
3201 Overflow of the end result

17
4 Assignment of internal fault 999

D1 D2 Description
3230 UP Version differs from HP version

3250 Invalid parameter for staged burner-firing-rate controller

3300 Sequence control BrennUm default case entered

3301 Sequence control leakage test default case entered
3302 Sequence control FAT default case
3303 Sequence control post ventilation default case
3304 Sequence control pre ventilation default case entered
3305 Sequence control Ingnition default case entered
4000 0 No curve point to the load of the ignition point.
4001 0 ucPIdx_R >= ucPunktAnzahl

4100 sRampe.ucState Invalid value of sRampe.ucState

4200 ucVBMode Invalid value of ucVBMode

4302 0 No active air channel is defined (parameterization error).

4400 ucSteuerArtEx Invalid value of ucSteuerArtEx

4401 0 Timeout while waiting for ???
4402 ucSteuerArtEx Invalid value of ucSteuerArtEx
4403 ucKanStat (ucKanStat & Def_VKM2_MSK) != Def_VKM2_DVAL
4404 0 Timeout while waiting for ???
4405 ucKanStat Disabled channel is moving!
4406 ucRzStState[ucKnr] Invalid value of ucRzStState[ucKnr]
4407 ucVBStat Invalid value of ucVBStatn

4500 0 sRampe.uiLaufzeit == 0!
4501 ucKnr IfKM_VB() returned 0

4600 ucVorgabe Invalid value of ucVorgabe

4601 (sRampe.uc2VBKMsk | Bei VSM_NOVB dürfen kein VB-Kanäle aktiv sein.
sRampe.ucVBKMsk)
4602 sRampT.ucNState Unknown default state
4603 sRampe.ucState Invalid value of sRampe.ucState

4700 0 Ramp time expired!

4701 Transferred channel number out of the permitted range
4702 Transferred channel number out of the permitted range
4703 Transferred channel number out of the permitted range
4704 Transferred channel number out of the permitted range
4705 ucKnr Transferred channel number out of the permitted range
4706 ucKnr Transferred channel number out of the permitted range
4707 ucKnr Transferred channel number out of the permitted range

18
4 Assignment of internal fault 999

D1 D2 Description
4708 ucKnr Transferred channel number out of the permitted range
4709 ucKnr Transferred channel number out of the permitted range
4710 ucKnr Transferred channel number out of the permitted range
4711 ucKnr Transferred channel number out of the permitted range
4712 ucKnr Transferred channel number out of the permitted range
4713 ucKnr Transferred channel number out of the permitted range
4714 ucKnr Transferred channel number out of the permitted range
4715 ucKnr Transferred channel number out of the permitted range
4716 ucKnr Transferred channel number out of the permitted range
4717 ucKnr Transferred channel number out of the permitted range

4800 uiActTmr ucErg > 0!

4801 ucSgIdx Parameter modification Knf_uiActuatorDirX while fuel/air ratio control is
active or outside the operation modes “Burner Off” or “Fault”.
4802 0 Zulässiger Kanal-Fahrbereich zu gering für Durchführung Max-Speed-Mes-
sung

4900 ucKnr Division by 0

5000 enInterneLastSeq Invalid value of enInterneLastSeq
5001 0 Ambiguous DPS+ / DPS- for load stage selection
5002 0 Curve error: Curve for n-staged oil or channel speed for actuators was not
determined.
5003 0 Invalid parameter in function call
5004 0 Timers for the control of the stage switching time do not fit together: Switch-
ing time of internal load < supervised time for set load.
5005 0 Invalid stage curve with internal load set by the stage controller
5007 0 Invalid load value while adjusting the staged oil curve
5008 0 Invalid stage-activation control mode
6000 ucSteuerArtEx Unknown Mode of Channel-Control
6001 ucBetrMoNr Overadressing of Array was detected

6100 ucKnr Unknown Mode of Channel-Control

6200 0 Avoid an endless loop

6201 0 Avoid an endless loop
6203 0 SSR.sS0.ucAkt SSR.sS0.uiKanalenb changed without
AufrufKurve2Workram
6204 0 No completely valid point found but curve not empty.
6205 Ermittelte Punkteanzahl Number of points don’t match Ram-curve (fatal error with task).
6206 Punktindex Wirkkurve Writing firing-rate failed (Ram-error)
6207 Punktindex Originalkurve Firing-rate point in original curve invalid
6208 Punktindex Originalkurve Invalid point index
6209 0 Point-approximation not possible, no prior point.
6210 0 Point-approximation not possible, no following point.
6211 0 Point-approximation failed, invalid according point.
6212 Punktindex Wirkkurve Writing setpoint failed (Ram-error)

19
4 Assignment of internal fault 999

D1 D2 Description
6213 Punktindex Originalkurve Invalid point-index
6214 0 Point-approximation not possible, no prior point.
6215 0 Point-approximation not possible, no following point.
6216 0 Point-approximation failed, invalid according point.
6217 Punktindex Wirkkurve Rück-Sollwert-Schreiben gescheitert (Ram-Defekt).
6218 Punktindex Originalkurve Invalid point-index
6219 0 Point-approximation failed, invalid according point.
6220 Punktindex Wirkkurve Evaluated-Correction-Setpoint-Writing failed (Ram-error).
6221 Punktindex Originalkurve Invalid point-index
6222 0 Writing failed: Ram-error
6223 0 Writing failed: Ram-error
6224 Fehleranzahl Too many differences between curves
(sliding counter, substract 1 per cycle)
6225 Statenummer Undefined state of statemachine

6300 ucSMState Detect undefined state of statemachine

6400 Channel Nr. Division by 0

6500 Channel Nr. Fault channel index
6501 Channel Nr. Fault channel index
6502 Channel Nr. Fault channel index
6504 Channel Nr. Fault channel index
6505 Channel Nr. Fault channel index
6506 Channel Nr. Fault channel index
6507 Channel Nr. Fault channel index
6508 Channel Nr. Fault channel index
6509 Channel Nr. Fault channel index

7040 0 No O2-control-operating mode parameter

7045 sO2DataSR.ucO2Mode O2-operating mode with unknown resource O2-control output
7060 Infodata Illegal curve set or count numbers O2-Optimisation curve
7061 ucldx+1 Illegal curve point O2-Optimisation curve
7062 eWrErr Writing fault of SysEE_eWrite_sER
7063 ucKSNr+1 Illegal curve set number
7064 eWrErr Writing fault of SysEE_eWrite_sER
7065 sO2DataSR.ucKKSState Unknown state on state machine SRSaveKK_SM
7066 SRSaveKK_SM Illegal numbers of curve points
7080 ucParaIdx Request unknown O2-parameter
7140 sO2DataNSR.ucLMDSState Unknown state on state machine SRSaveKK_SM
7041 sO2DataNSR.ucLMDSState Unknown state on state machine SRSaveKK_SM
7160 ucHisSM_S Unknown state on state machine O2HistorieSM
7180 ucPktNr Illegal count number or count
7400 ucPktNr Illegal count number or count
7500 ucldx2 Unknown index
7520 ucBufNr Call iaverage value with undefined buffer index

20
4 Assignment of internal fault 999

D1 D2 Description
7525 eWrErr EEProm Schreiben Sys_eWrite_sER() failed
7526 eWrErr EEProm Schreiben Sys_eWrite_sER() failed
7527 eWrErr EEProm Schreiben Sys_eWrite_sER() failed
7528 ucCOStoreState Unknown state on state machine StoreCOKurve_SM
7900 ucBufNr Call iaverage value with undefined buffer index

21
5 Assignment of CO/O2 control faults or information

5 Assignment of CO/O2 control faults or information

NOTICE!
Depending on the parameter settings,O2 control is deactivated or fault switching of the burner
is triggered.
Factory setting: P 142 = 0 (CO/O2 control is inactive, burner is not switched off)

O2 fault example:

O2 measured value during pre-ventilation is

too high(24 %)

Fig. 5-1 Display of an O2 monitoring fault

No. UI300 fault Fault description

display
0001 O2 fault od O2 measured value during pre-ventilation is too low.
0002 O2 fault od O2 measured value during pre-ventilation is too high.
0003 O2 fault od O2 measured value after ignition is too high.
0004 O2 fault ot/od No probe dynamics - O2 regulation is deactivated
0006 O2 fault ot/od O2 measured value is above the upper band.
0008 O2 fault O2 measured value is below the lower band.
0009 O2 fault Half air shortage reached.
0011 O2 fault O2 measured value fault on LSB.
0012 O2 fault O2 setpoint curve is incorrect.
0013 O2 fault ot Air shortage: O2 control has been deactivated.
0018 O2 fault od O2 setpoint curve is incorrect.
0020 O2 fault O2 controller fault
0060 O2 fault ot The watchdog processor has detected a fault. O2 control has
been switched off after timeout.
0073 O2 fault Unknown CO/O2 operating status
0074 O2 fault Invalid O2 operating mode

ot = temporary fault
od = permanent fault

22
5 Assignment of CO/O2 control faults or information

CO fault example:

The plausibility check of the sensor voltage

of the COe measuring cell with O2 trim has
been activated.

Fig. 5-2 Display of a CO monitoring fault

When the following monitoring routines are activated, CO control is deactivated. Depending
on the settings made, optimisation is completely deactivated (factory setting) or switched to
O2 trim on the fly.

No. Error/Info Fault description

0040 CO-Fehler ot No edge information available on LAMTEC SYSTEM BUS.
0041 CO-Fehler ot CO sensor voltage outside the monitoring range.
0042 CO-Fehler ot Offset voltage of the COe measuring cell outside the monitor-
ing range.
0043 CO-Fehler ot Internal resistance of the COe measuring cell outside the mon-
od itoring range.
0044 CO-Fehler od Probe temperature of the COe measuring cell outside the
monitoring range.
0045 CO-Fehler ot Probe dynamic too low.
od
0047 CO-Fehler ot Watchdog processor swithces OFF the CO control.
0049 CO-Fehler ot O2 monitoring switches OFF CO control.
0050 CO-Fehler ot The effective probe voltage UCOe is incorrect..
0052 CO-Fehler ot CO edge signal is not plausible.
0053 CO-Fehler ot CO edge signal is not plausible.
0054 CO-Fehler ot CO edsge is overshoot for too long after ignition.
0055 CO-Fehler ot O edsge is overshoot for too long after ignition.
ot = temporary fault
od = permanent fault

23
 Copyright© 2011 LAMTEC
DLT1205-14-aEN-004

The information in this publication is subject to technical changes.

LAMTEC Meß- und Regeltechnik LAMTEC Leipzig GmbH & Co. KG Presented by:
für Feuerungen GmbH & Co. KG

Wiesenstraße 6 Portitzer Straße 69

D-69190 Walldorf D-04425 Taucha
Phone: +49 (0) 6227 / 6052-0 Phone: +49 (0) 34298 / 4875-0
Fax: +49 (0) 6227 / 6052-57 Fax: +49 (0) 34298 / 4875-99
e-mail:[email protected] Print no. DLT1205-14-aEN-004
www.lamtec.de Printed in Germany