Delta Loop antenna

EADELTA11 Article no: 17826.11B

3,80m

Rev. v2.0 - 08MAR2022

SPECIFICATIONS EADELTA11
Frequency range: 14,0 ~ 54 MHz.
Gain: (dBi) 6,58 ~ 8,96 dBi
Elevation angle: 12 ~ 32 deg.
SWR: 1,1 : 1 ~ 4,5 : 1 (ATU needed)
Max. power: 1,0 kW
Height: 3,8 m / 12,46'
Width: 3,6 m / 11,80'
Rotation radius: 1,80 m / 5,90'
Wind resistance: >
160 km/h / >
100 mph
 ENGLISH
STEP #1
Assembly of the elements to the mast plate
Note: Only fully tighten the screws after Step #2 is accomplished

Screw M6 x 50
S912-9650

Telescopic
tube Plastic block
EADELTA11 EAHYP020

Mast plate
Nut M6 selflock
EA010081
S985-906

STEP #2
Mounting the balun
U-bolt M6
A-0891

Balun
11740.BALUN

Nut M6
S934-96
Spring washer M6
Feed plate S127-96
EA01ALI11
remove the nuts and washers from the balun
(11740.BALUN) mount the feed plates
(EA0ALI11) in the folowing order to the balun as
well as to the telescopic elements (EADELTA11)
Nut M4
DIN 934 1. washer M4 DIN 9021
2. feed plate (EA01ALI11)
Washer M4
3 washer M5 DIN 9021
DIN 9021 4. nut M5 DIN 934
2
 ENGLISH
STEP #3
Extension of the telescopic elements

Extend the tubes with the help of the marks, located 15 cm before the elemt ends. These marks show the extension
lenghts and also determine where the hose clamps have to be positioned. Repeat this step for all extendable
tubes of both elements.
16 mm Ø

13mm Ø

10mm Ø
HOSE CLAMP 12-22mm Ø HOSE CLAMP 10-16mm Ø HOSE CLAMP 8-12mm Ø
(P01000024) (P01000033) (P01000022)
16mm Ø

13mm Ø
20mm Ø

STEP #4
After the tubes are extended, mount the copper wire that closes the Delta. Fig. A is shows how the copper
wire is attached to the tube end 10mm. When the first wire end is placed and secured to the tube, you will
need to tighten the 2 tips of aluminum to attach the copper wire at each end. Fig. B shows how the final
assembly should look like.
Fig. A

Mark with
insulating tape
Fig. B

Mark with
insulating tape

Top section
10mm Tube

3
 ENGLISH

STEP #5
MAST TO BOOM PLATE ASSEMBLY

Nut M8
S934-98

MAST
washer M8
S127-98

Bracket
23035.50

U-bolt M8
A-0163

4
PACKING LIST
BAG #1
PART # PART IMAGE DESCRIPTION DIMENSIONS QUANTITY

A-0163 U-bolt M8 x 50 2

23035.50 bracket 50 mm 2

S127-98 WASHER DIN 127 M8 4

S934-98 NUT DIN 934 M8 4

A-0891 U-bolt M6 x 52 mm 1

S127-96 WASHER DIN 127 M6 2

S934-96 Nut DIN 934 M6 2

P1300001 Allen key 5mm 1

P1300003 Wrench M10 1

P1300005 Wrench M13 1

BAG #2
PART # PART IMAGE DESCRIPTION DIMENSIONS QUANTITY

P0100024 Hose clamp 12 - 22 2

P0100033 Hose clamp 10 - 16 2

P0100022 Hose clamp 8 - 12 2

23060.3 Wire clamp M3 2

5
PACKING LIST

BAG #3
PART # PART IMAGE DESCRIPTION DIMENSIONS QUANTITY

EAHYP020 Plastic block 20 mm Ø 4

S912-9650 Socket head screw DIN 912 M6 x50mm 8

S127-96 Spring washer DIN 127 M6 8

S985-906 NUT DIN 985 selflock M6 8

BAG #4
PART # PART IMAGE DESCRIPTION DIMENSIONS QUANTITY

11740.BALUN Balun 1

EA01ALI11
Feed plate 2

EAntenna Delta Loop

LOOSE PARTS
PART # PART IMAGE DESCRIPTION DIMENSIONS QUANTITY

EADELTA11 TELESCOPIC 4 TUBES SET Ø 20 - 10mm 2

EA010081 MAST PLATE 200 x 200 x 10 mm 1