SAFETY DATA SHEET (SDS)

SDS in accordance with UN GHS Purple Book CAP–SDS–PP–302–HY3.8FY (Rev.02)

This SDS is effective as from 15 Sep 2021 and supersedes previous document published |Validity date: 15 Sep 2026

SECTION-1. IDENTIFICATION

Product/Material : Polypropylene Homopolymer Yarn Grade

Product grade : TRILENE HY3.8FY
Application : Woven bag, tarpaulin, geotextile, rope, drinking straw, carpet backing, etc
Manufacturer : PT CHANDRA ASRI PETROCHEMICAL Tbk (CAP)
Head Office : Wisma Barito Pacific, Tower A, 7th floor, Jl. Letjend S. Parman, Kav.62-63.
Jakarta 11410, Indonesia.
Plant : Jl Raya Anyer Km.123, Ciwandan, Cilegon 42447, Indonesia. Phone: 62-254-601501
Emergency contact (24 hrs) : [email protected], Phone: +62-254-601829; 254-601501 Ext 1232
Additional Information : Commercial Inquiry : [email protected] / [email protected]
Technical Inquiry : [email protected]

SECTION-2. HAZARD IDENTIFICATION

Hazardous Component : None

Hazard statements : Avoid contact with molten material
NFPA Hazard Rating : Health = 0 Flammability = 1 Reactivity = 0

SECTION-3. COMPOSITION / INFORMATION ON INGREDIENTS

Chemical Name / Family Name : Polypropylene / Polyolefin Chemical Formula: (C3H6)n

Common Name, Trade Name : PP Homopolymer CAS No : 9003-07-0

NO. COMPOSITION PERCENT

1 Polypropylene Homopolymer ≥ 99
2 Minor Additives <1

SECTION-4. FIRST-AID MEASURES

The Health effects below are based upon component health effects consistent with requirement under OSHA hazard
communication (29 CFR 1910.1200).
First-Aid Step
Inhalation : Product fines may cause mechanical irritation
Skin Contact : Product is unlikely to cause irritation at room temperature
Eye Contact : Product fines may cause mechanical irritation
Ingestion : Product is practically non-toxic
Sign and Symptoms : Irritation as noted above
Aggravated Medical Condition : Preexisting eye and respiratory disorder may be aggravated by exposure to product
Fines
SECTION-5. FIRE-FIGHTING MEASURES

Extinguishing Media : Use water fog, foam, dry chemical or CO 2.

Unusual Fire and Explosion : Treat as a solid that can burn, molded parts generally burn slowly with a low smoke

Safety Data Sheet – PP – 302 – HY3.8FY (Rev.02) Page 1 of 4

 Hazard density and flaming drips under certain conditions can burn with a high smoke
density
Fire Fighting Procedures and : Material will not burn unless preheated. Do not enter confined fire space without full
Precaution bunker gear (helmet with face shield, bunker coats, gloves and rubber boots)
including a positive pressure NIOSH approved self-contained breathing apparatus.
Cool fire exposed containers with water.
Protective Clothing for Fire : Hand gloves, goggles
Fighter

SECTION-6. ACCIDENTAL RELEASE MEASURES

Small Spill and Leak : Pellets on the floor could present a serious slipping problem. Exercise good
housekeeping to avoid this hazard. Sweep, shovel or vacuum material into clean
containers.
Large Spill and Leak : Use a shovel to put the material into a convenient waste disposal container do not
allow any potentially contaminated water with pellets to entry any waterway, sewer or
drain.

SECTION-7. HANDLING AND STORAGE

Personal Precautionary : Avoid contact with molten material

Measures

Handling : Maintain good housekeeping. Keep away from heat, sparks, open flame or any
ignition source. Use with adequate ventilation. After handling, always wash hands
thoroughly with soap and water. Spilled pellet may create a slipping hazard.
Electrostatic charge may build up during handling. Grounding of equipment is
recommended.
Storage : Store in a dry place with adequate ventilation and away from direct sunlight,
excessive heat and strong oxidizers. Keep packaging (container) closed to prevent
contamination

SECTION-8. EXPOSURE CONTROLS / PERSONAL PROTECTION

Control Parameters : Although general room ventilation should be adequate in most applications, local
exhaust ventilation is recommended for control of airborne dust, fumes and vapors,
particularly in confined areas.
Respiratory Protection : Use NIOSH approved respirator if unable to control airborne dust, fumes and vapors.
Eye Protection : Wear eye protection (safety glasses, goggles, face-shield) when processing.
Skin and Body Protection : Wear chemical-resistant gloves, heat protective gloves and protective clothing as
well as a face-shield
Other Personal Protection : Use safety non-slip shoes in area where spills or leaks occur.

SECTION-9. PHYSICAL AND CHEMICAL PROPERTIES

Appearance and Odor : 3mm ø Solid, Whitish in color and essentially odorless pellet
Organoleptic : Tasteless
Melting Point / freezing Point : 157 – 170OC / Not applicable
Initial Boiling Point : Not applicable
Flash Point : Not applicable, Combustible solid
Evaporation Rate (n-Butyl : Not applicable
Acetate = 1)
Specific Gravity (H2O=1) : <1.0
Safety Data Sheet – PP – 302 – HY3.8FY (Rev.02) Page 2 of 4
 Solubility (in water) : Insoluble
Viscosity : Solid, not applicable
Melt Index230oC/2.16kg : 3.8 gr/10min
Density : 0.903 gr/cm3

SECTION-10. STABILITY AND REACTIVITY

Stability : Stable under normal operating conditions of storage, handling and use.
Hazardous Reaction : Not likely to occur under normal operating conditions of storage, handling and use
Conditions to Avoid : Strong oxidizing agents. Temperature over 300OC, sparks and open flame.
Hazardous Decomposition : Thermal decomposition products are highly dependent on the combustion
Products conditions. A complex mixture of airborne solid. Liquid particulates and gases will
evolve when this material undergoes pyrolysis or combustion. Carbon monoxide and
unidentified organic compounds may be formed upon combustion

SECTION-11. TOXICOLOGICAL INFORMATION

Symptoms related to : Material is considered essentially inert, non-toxic and practically not harmful as well
toxicological characteristic as not hazardous substances under RoHS regulation. Exposures to high levels of
dust or heated fumes may cause irritation.
Carcinogenicity : Material is not carcinogenic as listed by OSHA, NTP or IARC

SECTION-12. ECOLOGICAL INFORMATION

Ecotoxicity : Material is not expected to be harmful to aquatic organisms

Environmental Fate : Material is not volatile, insoluble in water, and resistant to biodegradation
Mobility : The product has low soil mobility. This material floats on water.

SECTION-13. DISPOSAL CONSIDERATIONS

Waste Disposal : Place in an appropriate disposal facility in compliance with local regulations

SECTION-14. TRANSPORT INFORMATION

Transportation Classification : Not controlled under DOT (USA), TDG (Canada), ADR (Europe), IMDG and IATA

SECTION-15. REGULATORY INFORMATION

The components of this product are listed on the EPA/TSCA inventory of chemical substances.

HCS Classification : This product is not a "Hazardous Chemical" as defined by the OSHA Hazard
Communication

SECTION-16. OTHER INFORMATION

Abbreviations that may have been used in this document:

ACGIH : AMERICAN CONFERENCE of GOVERNMENTAL INDUSTRIAL HYGIENISTS
DOT : DEPARTMENT OF TRANSPORTATION
NIOSH : NATIONAL INSTITUTE for OCCUPATIONAL SAFETY & HEALTH
OSHA : OCCUPATIONAL SAFETY & HEALTH ADMINISTRATION
RoHS : RESTRICTION of HAZARDOUS SUBSTANCES
NTP : NATIONAL TOXICOLOGY PROGRAM
IART : INTERNATIONAL ASSOCIATION OF RESPIRATORY THERAPISTS
HCS : HAZARD COMMUNICATION STANDARD
LDK : LEMBAR DATA KESELAMATAN
Safety Data Sheet – PP – 302 – HY3.8FY (Rev.02) Page 3 of 4
 EEC : EUROPE ECONOMIC COMMITTEE

This Safety Data Sheet contains the following historical of revisions :

Rev No Issued Date Revision Change Description
00 09 Jan 2015 Original Document
01 25 Jan 2019 SECTION-02 1. Pictogram was modified
2. NFPA was modified
SECTION-05 Protective clothing for fire fighter was modified
02 15 Sep 2021 SECTION-01 Additional information was modified

THE INFORMATION EXPRESSED HEREIN IS THOSE OF QUALIFIED CURRENT KNOWLEDGE AND EXPERIENCE
AND THAT THE INFORMATION IS SUFFICIENT OF ALL CASES. USERS SHOULD CONSIDER THE DATA AS A
SUPPLEMENT TO OTHER INFORMATION AND SHOULD MAKE INDEPENDENT DETERMINATION OF ITS
SUITABILITY, THEIR EMPLOYEES AND CUSTOMERS AND OF THE ENVIRONMENTAL PROTECTION TO ASSURE
PROPER USE AND DISPOSAL OF THE MATERIAL. RESPONSIBILITY FOR USAGE, STORAGE, HANDLING AND
DISPOSAL OF THE PRODUCTS DESCRIBED HEREIN, WHETHER ALONE, OR IN COMBINATION WITH ANY OTHER
SUBSTANCE, IS THAT OF THE PURCHASER AND/OR END-USER. CAP MAKES NO WARRANTY, EXPRESSED OR
IMPLIED REGARDING THE ACCURACY OF THESE DATA OR THE RESULT TO BE OBTAINED FROM THE USE
THEREOF. CAP ASSUMES NO RESPONSIBILITY FOR INJURY FROM THE USE OF THE PRODUCT DESCRIBED
HEREIN.

Safety Data Sheet – PP – 302 – HY3.8FY (Rev.02) Page 4 of 4