RRB ALP CBT 2 Fitter Question Paper MCQ

Contents
RRB ALP CBT 2 Fitter 21/01/2019 Shift 1 .......................................................................................................................... 2
RRB ALP CBT 2 (Fitter) 23/1/2019 Shift - 2..................................................................................................................... 11

RRB ALP CBT 2 Fitter 21/01/2019 Shift 1

1. What is the size of cross section of slip gauge?

a) 42 mm x 9 mm
b) 22 mm x 9 mm
c) 32 mm x 9 mm
d) 52 mm x 9 mm
Ans. C

2. Which of the following fitting items is used to block the end of a pipe?
a) Plug
b) Reducer
c) Union
d) Coupling
Ans. A

3. Which nut can be easily operated with thumb and finger?

a) Capstun nut
b) Dome nut
c) Wing nut
d) Lock nut
Ans. C

4. Which of the following file is commonly used for finishing inside the teeth of gear wheels?
a) Mill saw file
b) Riffle file
c) Barrette file
d) Cross file
Ans. C

5. Jigs are available for:

a) turning
b) drilling and boring
c) grinding
d) milling
Ans. B
6. Which type of belt is used when the distance between the shafts is too short (<1 meter distance between drives)?
a) V-belt
b) Ribbed belt
c) Link belt
d) Flat belt
Ans. A

7Which of the following is NOT a type of common threaded fastener?

a) Nail
b) Bolt
c) Screw
d) Nut
Ans. A

8. The main purpose of using go and no go gauge is to use it as ______?

a) Limit gauge
b) Radius gauge
c) Pitch gauge
d) Slip gauge
Answer – a

9. Which of the following marking media is used for filed or machine finished surfaces?
a) White leap powder mixed with turpentine
b) Chalk powder mixed with water
c) Chalk powder mixed with methylated spirit
d) Prussian blue oil paint
Ans. D

10. Sharing the sheet into two pieces or more is known as _______.
a) notching
b) parting
c) lancing
d) grooving
Ans. B

11. Which material is used to make center punch?

a) Cast iron
b) Zinc
c) high carbon steel
d) copper
Ans. C

12. The outer part of a holding jaw in a bench vice is made of which of the following materials?
a) Aluminium
b) Copper
c) Mild steel
d) Cast iron
Ans. D
13. The dimension of a nut is expressed in terms of:
a) pitch diameter of the bolt
b) core diameter of the bolt
c) nominal diameter of the bolt
d) head of the bolt
Ans. C

14. What is the percentage of tin in soft solder?

a) 30%
b) 63%
c) 42%
d) 50%
Ans. B

15. Which of the following types of gear sets is used to convert cyclic motion into linear motion and linear motion
into cyclic motion?
a) Bevel gear
b) Hypoid gear
c) Spiral beval gear
d) Rack and pinion
Ans. D

16. Tab washers are used:

a) for locking the nuts
b) to maintain bore diameter
c) for dimensional accuracy
d) for structural assemblies
Ans. A

17. Which of the following lapping abrasive is used for obtaining high quality finish?
a) Diamond
b) Emery cloth
c) Aluminium oxide
d) Coarse grain abrasive
Ans. C

18. Which of the following instruments is NOT used to measure angles?

a) Clinometers
b) Bevel protector
c) protector head
d) Optical flats
Ans. D

19. Zinc coated iron is known as:

a) Galvanised iron b) Black iron
c) Cast iron d) Stainless sheet
Ans. A
20. What is the included angle of a lathe dead center?
a) 600
b) 450
c) 900
d) 300
Ans. A

21. Which of the following is fitted on top of the compound rest of a lathe?
a) Chuck
b) Saddle
c) Cross slide
d) Top slide
Ans. D

22. Which of the following welding process uses carbon dioxide?

a) Gas Tungsten Arc welding
b) Shielded metal arc welding
c) Gas metal arc welding
d) Submerges arc welding
Ans. C

23. Which material is used to make power hacksaw blades?

a) High carbon steel
b) Mild steel
c) High speed steel
d) Medium carbon steel
Ans. C

24. The measuring faces of the slip gauges are finished by ______
a) Honing
b) Lapping
c) Reaming
d) Drilling
Ans. B

25. Conventionally, which type of surface is produced by turning operation in a lathe machine?
a) Cylindrical
b) Square
c) Plane
d) Irregular shape
Answer – a

26. Which of the following gauges is used to find the pitch of a thread?
a) Feeler gauge
b) Radius gauge
c) Screw pitch gauge
d) Plus gauge
Ans. C
27. What is the purpose of an idler gear used in gear trains?
a) To increase the contact area of pulley and belt
b) To obtain minimum centre distance between driving and driven shaft
c) To objtain maximum centre distance between driving and driven shaft
d) To have required direction of rotation
Ans. D

28. Plain ring gauges are used to check:

a) accuracy of external threads
b) accuracy of internal threads
c) inside diamete of work piece
d) outside diameter of work piece
Ans. D

29. Which one of the following is a multi-point cutting tool?

a) File
b) Hammer
c) Scrapper
d) chisel
Ans. A

30. Which material is used to make file?

a) Low carbon steel
b) High carbon steel
c) Aluminum
d) Cast iron
Ans. B

31. Which of the following gauges is used to check the diameter of a wire?
a) Plate gauge
b) Wire gauge
c) Radius gauge
d) Reeper gauge
Ans. B

32. The process of enlarging a hole size and enhancing its surface finish is known as ____.
a) boring
b) reaming
c) drilling
d) countersinking
Ans. A

33. The ‘ring oiling system’ is also known as:

a) splash feed system
b) Grease feed system
c) Lubricator system
d) Force feed system
Ans. A
34. What is the colour of oxygen gas cylinder?
a) Maroon
b) Blue
c) Green
d) Black
Ans. D

35. Which of the following compass is used to scribe a circle or an arc with a large diameter?
a) Trammel compass
b) Ordinary compass
c) Wing compass
d) Spring compass
Ans. A

36. What is the accuracy of Vernier height gauge?

a) 0.02 mm
b) 0.01 mm
c) 0.2 mm
d) 0.1 mm
Ans. A

37. Which type of thread is used in screw jack?

a) Buttress
b) Square
c) Knuckle
d) Acme
Ans. B

38. Which of the following process is used for super finishing of bores in ferrous metals?
a) Honing
b) Grinding
c) Filling
d) Drilling
Ans. A

39. Identify the standard format of pipe thread from the given options.
a) BSW
b) BSP
c) BSF
d) BA
Ans. B

40.The difference between the maximum limit of size and minimum limit of size in assembling a product is known as:
a) Basic size
b) Deviation
c) Zero line
d) Tolerance
Ans. D
41. ______ is a process of case hardening in which the outer layer is made hard by increasing amount of carbon.
a) Annealing
b) Normalizing
c) Carburizing
d) Tempering
Ans. C

42. The least count of a steel rule is _____.

a) 0.01 mm
b) 0.05 mm
c) 0.50 mm
d) 0.02 mm
Ans. C

43. Which of the following is not used to connect two shafts together in order to transmit power?
a) Bolts
b) Ball bearings
c) Couplings
d) Keys
Ans. B

44. The property of a metal to draw it into thin sheets is termed as ______.
a) Malleability
b) Britleness
c) Toghness
d) Hardness
Ans. A

45. The type of thread used in lead screw of a lathe is _____

a) Knuckle thread
b) Square thread
c) Worm thread
d) Buttress thread
Ans. B

46. What is the purpose of a non-return valve in a water pipe line?

a) It enables three-way flow
b) It enables one-way flow
c) It enables four-way flow
d) It enables two-way flow
Ans. B

47. Drill chucks are fitted on the drilling machine spindle by means of _____
a) Arbor
b) Drift
c) Knurld ring
d) Pinion & Key
Ans. A
48. Which hand tool is used to form internal thread in a hole?
a) Scrapper
b) Tap
c) Drill
d) Reamer
Ans. B

49. Which material is used to make races of ball bearings?

a) Brass
b) Chromium steel
c) Cast iron
d) Plastic
Ans. B

50. The surface connecting crest & root of a thread is termed as:
a) thread angle
b) Flank
c) Depth of thread
d) Pitch
Ans. B

51. Twist drills are made up which of the following materials?

a) High carbon steel
b) Titanium
c) Mild steel
d) Medium carbon steel
Ans. A

52. If you want to drill a hole in a switchboard, then you will use a ____.
a) pillar-drill machine
b) radial-drill machine
c) hand-drill machine
d) bench drill machine
Ans. C

53. Which among the following is the use of a GO gauge?

a) To check the size of a hole
b) To check surface finish
c) To ineasure thread angle
d) To measure thickness of a plate
Ans. A

54. When the size of a smallest hole is bigger than the size of the biggest shaft, then it is called as a/an ____
a) interference fit
b) progressive fit
c) clearance fit
d) transition fit
Ans. C
55. What is the purpose of a globe valve in a pipeline?
a) It provides strength to the joint
b) It avoids water from getting heated
c) It controls water flow
d) It avoid vacuum being formed
Ans. C

56. What is a metal’s ability to withstand wear, abrasion and penetration called?
a) Hardness
b) Toughness
c) Maleability
d) Brittleness
Ans. A

57. A feeler gauge is used for

a) Checking accuracy of holes
b) Checking gap between the mating parts
c) Checking radii of jobs
d) Adjusting the parts for play
Ans. B
RRB ALP CBT 2 (Fitter) 23/1/2019 Shift - 2
1. The process of beveling the end of an existing hole is called _____.
a) counter sinking
b) Spot facing
c) boring
d) counter boring
Ans. A

2. Which tool is used for forging compressive force application?

a) roller
b) Swage block
c) fullers
d) Hot chisel
Ans. A

3. A process, in which two surfaces are rubbed together with an abrasive between them, by hand movement or
using a machine is called ______
a) Lapping
b) Grinding
c) Honing
d) Finishing
Ans. A

4. The point angle of twist drill depends upon the _____.

a) cutting speed
b) material to be drilled
c) size of the drill
d) type of drilling machine
Ans. B

5. At which position of vernier height gauge, the scriber is on the same level (coplanar) as the base.
a) Vernier scale at 1/4th position
b) Vernier scale at 3/4th position
c) When Vernier scale reads zero
d) Vernier scale at middle position
Ans. C

6. After honing a stock, allowable tolerance varies from _____.

A) 0.0001 mm to 0.001 mm b) 0.005 mm to 0.5 mm
c) 0.5 mm to 1 mm d) 1 mm to 3 mm
Ans. B

7. Which type of boring machine is used for rapid and accurate work?
a) Horizontal boring machine b) Vertical boring machine
c) Jig boring machine d) Portable boring machine
Ans. C
8. Module of gear is the ratio between _____.
a) addendum and pitch circle diameter
b) addendum and dedendum
c) number of teeth and pitch circle diameter
d) pitch circle diameter and number of teeth
Ans. D

9. Which type of transformer is used in arc welding?

a) step up
b) Step down
c) Auto transformer
d) Torodial
Ans. B

10. Equipment downtime is decreased and the number of major repairs are reduced due to _____ maintenance.
a) reliability centered activities
b) value driven activities
c) preventive
d) predictive
Ans. C

11. Which of the following is not a friction clutch?

a) Cone clutch
b) Centrifugal clutch
c) Disc clutch
d) Fluid clutch
Ans. D

12. Case hardening is done on mild steel by ______ process.

a) nitriding
b) normailzing
c) hardening
d) annealing
Ans. A

13. For riveting aluminum sheets, the material of rivet should be _____
a) wrought iron
b) copper
c) brass
d) aluminum
Ans. D

14. Which is one-way valve among the given valves?

a) Ball valves
b) Check valves
c) Gage valves
d) Gate valves
Ans. B
15. With respect of tolerance, if the specification shown is 50.3 + 0.05 mm, means it is indicating ____.
a) Limiting dimension
b) Type of fit
c) Unilateral tolerance
d) Upper limiting tolerance
Ans. A

16. The measured size of the dimension of a component is called _____ size.
a) Basic
b) Allowed
c) nominal
d) actual
Ans. D

17. To assemble a finished machine component a _____ is used.

a) Hard face hammer
b) Sledge hammer
c) Mallet hammer
d) Claw hammer
Ans. C

18. The cone-shaped end of the drill bit used for cutting material is known as a ____
a) Point
b) Shank
c) Tang
d) Flute
Ans. A

19. The distance of a drill advances into the job per revolution is known as _____
a) RPM
b) Machine speed
c) Cutting speed
d) Feed
Ans. D

20. Which of the following couplings is better for transmitting high power at lower speed?
a) Flange coupling
b) Sleeve coupling
c) Split coupling
d) Universal coupling
Ans. A

21. In the honing process, _______

a) Surface finishing is obtained by rubbing with emery paper
b) material will be removed to correct size
c) no material will be removed to correct size
d) finishing of the material surface is done by abrasive rubbing
Ans. B
22. Which of the following comparators works on gears pinion, linkage, levers, springs etc?
a) Pneumatic comparator
b) Optical comparator
c) Mechanical comparator
d) Electrical comparator
Ans. C

23. Which of the following materials is not used for a bearing?

a) Chrome steel
b) Stainless steel
c) Bronze
d) Wood
Ans. D

24. When two mating parts are sometimes, an interference fit and sometimes a clearance fit is known as
a) Interference fit
b) Clearance fit
c) Transition fit
d) Running fit
Ans. A

25. Time dependent recoverable deformation under load is called ______ deformation.
a) elastic
b) inelastic
c) plastic
d) visco-elastic
Ans. B

26. On which part of the veriner height gauge, are the main scale divisions graduated?
a) Scriber
b) Beam
c) Fine adjustment nut
d) Base
Ans. B

27. Indexing fixture is used in ______

a) Countersink boring on a drilling machine
b) Gear cutting operation on a milling machine
c) Surface finishing on a milling machine
d) Turning operation on a lathe
Ans. B

28. Which angle can be checked by using a try square?

Ans. 900

29. Which of the following operations cannot be performed on lathe machine?

a) Taper turning b) Slotting c) Drilling d) Turning
Ans. B
30. Which attachment is used to cut internal or external tapers on a turret lathe?
a) Taper turning attachment
b) Morse taper attachment
c) Offsetting tailstock attachment
d) Sliding attachment
Ans. D

31. Which of the following gauge is used for calibrating the micrometers, sine bars and calipers?
a) Feeler gauge
b) Ring gauge
c) Go and NO go gauge
d) Slip gauge
Ans. D

32. ______ is a cooling medium applies for normalizing process.

a) Water
b) Under sand
c) Air
d) Oil
Ans. C

33. Which of the following gears have straight as well as spiral teeth?
a) Bevel gear
b) Spear gear
c) Hypoid gear
d) Helical gear
Ans. D

34. When a double nut tightens in the opposite direction to lock the nut it is known as ___
a) Left hand nut
b) Split nut
c) Right hand nut
d) Check nut
Ans. B

35. Which of the following notches is used when making a job with a 900 bend?
a) Slant notch
b) V notch
c) Wired notch
d) Square notch
Ans. B

36. Which of the following materials have not malleable property?

a) Iron
b) Graphite
c) Silver
d) Aluminum
Ans. B
37. Which of the following types of pulley is used in-group drives?
a) Jockey pulley
b) Split pulley
c) Fast and loose pulley
d) Solid pulley
Ans. C

38. _____ drill machine is used to make a hole in a switch board.

a) Bench
b) Column
c) Hand
d) Pillar
Ans. C

39. Which of the following bearings is suitable for high speed?

a) Tapered roller bearing
b) Needle roller bearing
c) Ball bearing
d) Cylindrical roller bearing
Ans. C

40. A small gear meshed with a cylindrical gear with infinity as pitch circle radius is known as ____
a) rack and pinion
b) bevel gear
c) worm and worm wheel
d) spur gear drive
Ans. A

41. What is forging?

a) A die casting process
b) A machining process
c) Furnacing and hammering it
d) A tool
Ans. C

42. Lead is equal to double the pitch value then this type of thread is called as _____.
a) Single start thread
b) Multi start thread
c) Double start thread
d) Triple start thread
Ans. C

43. Brass is an alloy of ___

a) copper and zinc
b) copper and tin
c) lead and tin
d) copper and silver
Ans. A
44. The minimum material condition of an internal feature is called
a) lower limit
b) tolerance
c) allowance
d) upper limit
Ans. D

Fitter Previous Year MCQ Book in Just Rs.19/- [1200+ Important Questions]

ITI Employability skills MCQ Book in Just Rs.15/- Hindi/English (New Syllabus)

ITI Engineering Drawing Best MCQ Book in Just Rs.12/- [500 Question]

HEETSON

Telegram https://t.me/Heetson_Official

WhatsApp Channel

@heetsoniti

Question Paper Links

RRB ALP CBT 2 Fitter 21/01/2019 Shift 1

RRB ALP CBT 2 (Fitter) 21/01/2019 Shift 2

RRB ALP CBT 2 (Fitter) 21/01/2019 Shift - 3

RRB ALP CBT 2 (Fitter) 23/01/2019 Shift - 2

RRB ALP CBT 2 (Fitter) 23/01/2019 Shift - 3