GOVERNMENT OF MADHYA PRADESH

_____________________________ Department

Appendix 2.10
Tender Document

For Percentage Rate only in Works Departments and other

Departments similar to Works Departments
(Effective from 01/01/2014)

Office of the ______________________________

NIT Number and Date : __________________
Agreement Number and Date : __________________
Name of Work : __________________
: __________________
Name of the Contractor : __________________
Probable Amount of Contract
(Rs. In Figure) : __________________
(Rs. In Words) : __________________
__________________
Contract Amount
(Rs. In Figure) : __________________
(Rs. In Words) : __________________
__________________
Stipulated Period of Completion: __________________

Page 1 of 78
 Appendix 2.10
Tender Document
Table of Contents

Section Particulars Page

No
Section 1 NIT 3- 5

Instructions to Bidders (ITB) 6 - 12

Section 2 Bid Data Sheet 13 - 14

Annexure -A to M 15 - 37

Table of Clauses 38
Part - I General Conditions of 39 - 56
Contract (GCC)
Section 3 Contract Data 57 - 59

Annexure - N to W 60 - 75

Part - II Special Conditions of 76

Contract (SCC)
Section 4 Bill of Quantities (BOQ) 77

Section 5 Agreement Form 78

Page 2 of 78
 SECTION 1
Notice Inviting e-Tenders
Government of Madhya Pradesh
_____________________ Department
N.I.T. No __________________/e-tendering dated ___________

Online percentage rate bids for the following works are invited from registered
contractors and firms of repute fulfilling registration criteria:

S. No./Pkg/Code Work District(s) Probable Amount Completion

(Rs. in lakh) Period (months)

1. Interested bidders can view the NIT on website http://___________________.

2. The Bid Document can be purchased only online from __________ (time) _________
(date) to __________ (time) __________ (date).
3. Amendments to NIT, if any, would be published on website only, and not in newspaper.

Signature and Designation

Section 1 – NIT

Page 3 of 78
 Notice Inviting Tender
Government of Madhya Pradesh
_____________________ Department
Office of the _________________________
_________________________________________

N.I.T. No __________________/e-tender dated ___________

Online percentage rate bids for the following works are invited from registered
contractors and firms of repute fulfilling registration criteria:
S. No. Name District(s) Probable Earnest Cost of Bid Category Period of
/Pkg/ of Work Amount of Money Document of Completion
Code Contract Deposit (EMD) (In Rupees) Contractor (in Months)
(Rs. in lakh) (In Rupees)

1. All details relating to the Bid Document(s) can be viewed and downloaded free of
cost on the website.

2. Bid Document can be purchased after making online payment of portal fees
through Credit/Debit/Cash Card/internet banking.
3. At the time of submission of the Bid the eligible bidder shall be required to:
i) pay the cost of Bid Document;
ii) deposit the Earnest Money;
iii) Submit a check list; and
iv) Submit an affidavit.
Details can be seen in the Bid Data Sheet.
4. ELIGIBILITY FOR BIDDERS:

(a) At the time of submission of the Bid the bidder should have valid registration
with the Government of Madhya Pradesh, PWD in appropriate class. However,
such bidders who are not registered with the Government of Madhya Pradesh

Section 1 – NIT

Page 4 of 78
 and are eligible for registration can also submit their bids after having applied
for registration with appropriate authority.

(b) The bidder would be required to have valid registration at the time of signing of
the Contract.

(c) Failure to sign the contract by the selected bidder, for whatsoever reason, shall
result in forfeiture of the earnest money deposit.

5. Pre-qualification – Prequalification conditions, wherever applicable, are given in

the Bid Data Sheet.

6. Special Eligibility - Special Eligibility Conditions, if any, are given in the Bid Data
Sheet.
7. The Bid Document can be purchased only online from __________ (time) _________
(date) to __________ (time) __________ (date). Other key dates may be seen in
bid data sheet.

8. Amendments to NIT, if any, would be published on website only, and not

in newspaper.

(Signature and Designation)

Section 1 – NIT

Page 5 of 78
 SECTION 2
INSTRUCTIONS TO BIDDERS (ITB)
A. GENERAL
1. SCOPE OF BID

The detailed description of work, hereinafter referred as ‘work’, is given in the Bid
Data Sheet.
2. General Quality of Work:

The work shall have to be executed in accordance with the technical specifications
specified in the Bid Data sheet/ Contract Data, and shall have to meet high
standards of workmanship, safety and security of workmen and works.
3. PROCEDURE FOR PARTICIPATION IN E-TENDERING
The procedure for participation in e-tendering is given in the Bid Data Sheet.
4. ONE BID PER BIDDER

4.1 The bidder can be an individual entity or a joint venture (if permitted as per Bid
Data Sheet). In case the J.V. is permitted, the requirement of joint venture shall be
as per the Bid Data Sheet.

4.2 No bidder shall be entitled to submit more than one bid whether jointly or severally. If
he does so, all bids wherein the bidder has participated shall stand disqualified.

5. Cost of Bidding

The bidder shall bear all costs associated with the preparation and submission of
his bid, and no claim whatsoever for the same shall lie on the Government.
6. Site Visit and examination of works

The bidder is advised to visit and inspect the Site of Works and its surroundings and
obtain for itself on its own responsibility all information that may be necessary for
preparing the bid and entering into a contract for construction of the work. All
costs in this respect shall have to be borne by the bidder.
B. Bid Documents
7. CONTENT OF BID DOCUMENTS
The Bid Document comprises of the following documents:

1. NIT with all amendments.

Section 2 – Instruction to Bidders

Page 6 of 78
 2. Instructions to Bidders, Bid Data Sheet with all Annexures
3. Conditions of Contract:
i. Part I General Conditions of Contract and the Contract Data with all
Annexures; and
ii. Part II Special Conditions of Contract.
4. Specifications
5. Drawings
6. Priced Bill of Quantities
7. Technical and Financial Bid
8. Letter of Acceptance
9. Agreement, and
10. Any other document(s), as specified.
8. The bidder is expected to examine carefully all instructions, conditions of contract,
the contract data, forms, terms and specifications, bill of quantities, forms and
drawings in the Bid Document. Bidder shall be solely responsible for his failure to
do so.
9. Pre-Bid Meeting (where applicable)
Wherever the Bid Data Sheet provides for pre-bid meeting:

9.1 Details of venue, date and time would be mentioned in the Bid Data Sheet.
Any change in the schedule of pre-bid meeting would be communicated on
the website only, and intimation to bidders would not be given separately.

9.2 Any prospective bidder may raise his queries and/or seek clarifications in
writing before or during the pre-bid meeting. The purpose of such meeting
is to clarify issues and answer questions on any matter that may be raised at
that stage. The Employer may, at his option, give such clarifications as are
felt necessary.

9.3 Minutes of the pre-bid meeting including the gist of the questions raised
and the responses given together with any response prepared after the
meeting will be hosted on the website.

9.4 Pursuant to the pre-bid meeting if the Employer deems it necessary to

amend the Bid Document, it shall be done by issuing amendment to the
online NIT.

Section 2 – Instruction to Bidders

Page 7 of 78
10. Amendment of Bid Documents

10.1 Before the deadline for submission of bids, the Employer may amend or
modify the Bid Documents by publication of the same on the website.
10.2 All amendments shall form part of the Bid Document.

10.3 The Employer may, at its discretion, extend the last date for submission of
bids by publication of the same on the website.

C. Preparation of Bid
11. The bidders have to prepare their bids online, encrypt their Bid Data in the Bid
Forms and submit Bid Seals (Hashes) of all the envelopes and documents related to
the Bid required to be uploaded as per the time schedule mentioned in the key
dates of the Notice Inviting e-Tenders after signing of the same by the Digital
Signature of their authorized representative.
12. DOCUMENTS COMPRISING THE BID
The bid submitted online by the bidder shall be in the following parts:
Part 1 – This shall be known as Online Envelope A and would apply for all bids.
Online Envelop A shall contain the following as per details given in the Bid Data
Sheet:
i) Registration number or proof of application for registration and
organizational details in format given in the Bid Data Sheet.
ii) Payment of the cost of Bid Document;
iii) Earnest Money; and
iv) An affidavit duly notarized.
Part 2 – This shall be known as Online Envelope B and required to be submitted only
in works where pre-qualification conditions and/or special eligibility conditions are
stipulated in the Bid Data Sheet. Online Envelop B shall contain a self-certified sheet
duly supported by documents to demonstrate fulfillment of pre-qualification
conditions.

Part 3 – This shall be known as Online Envelope C and would apply to all bids.
Envelop C shall contain financial offer in the prescribed format enclosed with the
Bid Data Sheet.
13. Language
The bid as well as all correspondence and documents relating to the bid exchanged
by the Bidder and the Employer shall be in English or Hindi. Supporting documents
and printed literature that are part of the Bid may be in another language provided
they are accompanied by an accurate translation of the relevant passages in
English. In such case, for the purposes of interpretation of the bid, such translation
shall govern.

Section 2 – Instruction to Bidders

Page 8 of 78
14. TECHNICAL PROPOSAL

14.1 Only, in case of bids with pre-qualification conditions defined in the Bid Data
Sheet, the Technical Proposal shall comprise of formats and requirements
given in the Bid Data Sheet.

14.2 All the documents/ information enclosed with the Technical Proposal should
be self-attested and certified by the bidder. The Bidder shall be liable for
forfeiture of his earnest money deposit, if any document / information are
found false/ fake/ untrue before acceptance of bid. If it is found after
acceptance of the bid, the bid sanctioning authority may at his discretion
forfeit his performance security/ guarantee, security deposit, enlistment
deposit and take any other suitable action.
15. FINANCIAL BID

i. The bidder shall have to quote rates in format referred in Bid Data Sheet, in
overall percentage, and not item wise. If the bid is in absolute amount, overall
percentage would be arrived at in relation to the probable amount of contract
given in NIT. The overall percentage rate would apply for all items of work.
ii. Percentage shall be quoted in figures as well as in words. If any difference in
figures and words is found, lower of the two shall be taken as valid and correct.
iii. The bidder shall have to quote rates inclusive of all duties, taxes, royalties and
other levies; and the Employer shall not be liable for the same.
iv. The material along with the units and rates, which shall be issued, if any, by
the department to the contractor, is mentioned in the Bid Data Sheet.
16. PERIOD OF VALIDITY OF BIDS

The bids shall remain valid for a period specified in the Bid Data Sheet after the date
of “close for biding” as prescribed by the Employer. The validity of the bid can be
extended by mutual consent in writing.
17. EARNEST MONEY DEPOSIT (EMD)

17.1 The Bidder shall furnish, as part of the Bid, Earnest Money Deposit (EMD), in
the amount specified in the Bid Data Sheet.
17.2 The EMD shall be in the form of Fixed Deposit Receipt of a scheduled
commercial bank, issued in favour of the name given in the Bid Data Sheet.
The Fixed Deposit Receipt shall be valid for six months or more after the last
date of receipt of bids. However, other form(s) of EMD may be allowed by
the Employer by mentioning it in the Bid Data Sheet.

Section 2 – Instruction to Bidders

Page 9 of 78
 17.3 Bid not accompanied by EMD shall be liable for rejection as non-responsive.
17.4 EMD of bidders whose bids are not accepted will be returned within ten
working days of the decision on the bid.
17.5 EMD of the successful Bidder will be discharged when the Bidder has signed
the Agreement after furnishing the required Performance Security.
17.6 Failure to sign the contract by the selected bidder, within the specified
period, for whatsoever reason, shall result in forfeiture of the earnest
money deposit.
D. Submission of Bid

18. The bidder is required to submit online bid duly signed digitally, and Envelop ‘A’ in
physical form also at the place prescribed in the Bid Data Sheet.

E. Opening and Evaluation of Bid

19 PROCEDURE

19.1 Envelope ‘A’ shall be opened first online at the time and date notified and
its contents shall be checked. In cases where Envelop ‘A’ does not contain all
requisite documents, such bid shall be treated as non-responsive, and
Envelop B and/or C of such bid shall not be opened.

19.2 Wherever Envelop ‘B’ (Technical Bid) is required to be submitted, the same
shall be opened online at the time and date notified. The bidder shall have
freedom to witness opening of the Envelop ‘B’. Envelop ‘C’ (Financial Bid) of
bidders who are not qualified in Technical Bid (Envelop ‘B’) shall not be
opened.

19.3 Envelope ‘C’ (Financial Bid) shall be opened online at the time and date notified.
The bidder shall have freedom to witness opening of the Envelop ‘C’.

19.4 After opening Envelop ‘C’ all responsive bids shall be compared to
determine the lowest evaluated bid.

19.5 The Employer reserves the right to accept or reject any bid, and to annul the
bidding process and reject all the bids at any time prior to contract award,
without incurring any liability. In all such cases reasons shall be recorded.

19.6 The Employer reserves the right of accepting the bid for the whole work or
for a distinct part of it.

Section 2 – Instruction to Bidders

Page 10 of 78
20. Confidentiality

20.1 Information relating to examination, evaluation, comparison and

recommendation of contract award shall not be disclosed to bidders or any
other person not officially concerned with such process until final decision
on the bid.

20.2 Any attempt by a bidder to influence the Employer in the evaluation of the
bids or contract award decisions may result in the rejection of his bid.

F. Award of Contract
21. Award of Contract
The Employer shall notify the successful bidder by issuing a ‘Letter of Acceptance’
(LOA) that his bid has been accepted.
22. Performance Security

22.1 Prior to signing of the Contract the bidder to whom LOA has been issued
shall have to furnish performance security of the amount in the form and for
the duration, etc. as specified in the Bid Data Sheet.
22.2 Additional performance security, if applicable, is mentioned in the Bid Data
Sheet and shall be in the form and for the duration, etc. similar to
Performance Security.
23. Signing of Contract Agreement

23.1 The successful bidder shall have to furnish Performance Security and
Additional Performance Security, if any, and sign the contract agreement
within 15 days of issue of LOA.

23.2 The signing of contract agreement shall be reckoned as intimation to

commencement of work. No separate work order shall be issued by the
Employer to the contractor for commencement of work.

23.3 In the event of failure of the successful bidder to submit Performance

Security and Additional Performance Security, if any or sign the Contract
Agreement, his EMD shall stand forfeited without prejudice to the right of
the employer for taking any other action against the bidder.

Section 2 – Instruction to Bidders

Page 11 of 78
24. CORRUPT PRACTICES

The Employer requires that bidders observe the highest standard of ethics during the
procurement and execution of contracts. In pursuance of this policy, the Employer:

i. may reject the bid for award if it determines that the bidder recommended
for award has, directly or through an agent, engaged in corrupt, fraudulent,
collusive, or coercive practices in competing for the Contract; and

ii. may debar the bidder declaring ineligible, either indefinitely or for a stated
period of time, to participate in bids, if it at any time determines that the
bidder has, directly or through an agent, engaged in corrupt, fraudulent,
collusive, or coercive practices in competing for, or in executing, a contract.

For the purposes of this provision, the terms set forth above are defined as
follows:

a. “corrupt practice” means the offering, giving, receiving, or soliciting,

directly or indirectly, anything of value to influence improperly the
actions of another party;

b. “fraudulent practice” means any act or omission, including a

misrepresentation, that knowingly or recklessly misleads, or attempts to
mislead, a party to obtain a financial or other benefit or to avoid an
obligation;

c. “coercive practice” means impairing or harming, or threatening to

impair or harm, directly or indirectly, any party or the property of the
party to influence improperly the actions of a party;

d. “collusive practice” means an arrangement between two or more

parties designed to achieve an improper purpose, including influencing
improperly the actions of another party.
[End of ITB]

Section 2 – Instruction to Bidders

Page 12 of 78
 Bid Data Sheet

GENERAL
SR. No. PARTICULARS DATA
1 Office inviting tender
2 NIT No
3 Date of NIT
4 Bid document download available
from date & time
5 Website link http:// www……………..

SECTION 1 - NIT
CLAUSE
PARTICULARS DATA
REFERENC
E
2 Portal fees Rs.
3 Cost of bid document Rs.
Cost of bid document Payable at --------------------------------------------
--------------------------------------------
Cost of bid document In favor of --------------------------------------------
--------------------------------------------
4 Affidavit format Annexure B
5 Pre-qualifications required
If Yes, details Annexure C
6 Special Eligibility
If Yes, details Annexure D
7 Key dates Annexure A

SECTION 2 - ITB
CLAUSE
PARTICULARS DATA
REFERENCE
1 Name of ‘work’ …………………………………………………..
…………………………………………………..
…………………………………………………..
2 Specifications Annexure – E
3 Procedure for participation in e- Annexure – F
tendering
Whether Joint Venture is allowed NO
4
Pre bid meeting to be held
If Yes, Date, Time & Place Date :-----------
9
Time from:
Place:-----------

Section 2 – Bid Data Sheet

Page 13 of 78
 Bid Data Sheet
CLAUSE
PARTICULARS DATA
REFERENCE
Envelope-A containing : At the Office of the ------------------
i. Registration number or proof of --------------------------------------------
application for registration and --------------------------------------------
organizational details as per --------------------------------------------

12 Annexure H --------------------------------------------
ii. Cost of Bid Document --------------------------------------------
iii. EMD
iv. An affidavit duly notarized as
per Annexure - B Before --------------- (date)
should reach in physical form
14 Envelope-B Technical Proposal Annexure - I and
Annexure - I (Format I-1 to I-5)
Envelope-C Financial Bid Annexure - J
15 Materials to be issued by the Annexure - K
department
120 Days from the date of
16 Period of Validity of Bid submission of tender

Earnest Money Deposit Rs. …………………………………………….

Forms of Earnest Money Deposit i. FDR/ e-FDR
ii. Demand draft of scheduled
commercial bank
iii. Interest bearing securities of
17 post office.
EMD valid for a period of 180 Days
Executive Engineer
FDR must be drawn in favour of RES Division INDORE

21 Letter of Acceptance (LoA) Annexure L

Amount of Performance Security 5% of contract amount
Additional Performance Security, if any .……………………………..
Performance security in the format Annexure M
22 Executive Engineer RES Division
Performance security in favour of INDORE

12
Performance security valid up to Valid Contract period plus 3
months

Section 2 – Bid Data Sheet

Page 14 of 78
 Annexure – A
(See clause 1, 7 of Section 1 -NIT )

KEY DATES

S. Works Department Start Expiry Envelopes

Bidder's Stage
No Stage
Date Time Date Time
1 -

Purchase of Tender
– Online

2 -

Bid Submission
–Online

3 Mandatory submission - Envelope A

Open (Envelope- A)

4 Technical Proposal open Envelope B

( PQ Envelope- B)

5 Financial Bid open - Envelope C

(Envelope-C)

Original term deposit receipt of earnest money deposit, demand draft for the cost of bid
document and affidavit shall be submitted by the bidder so as to reach the office as
prescribed in Bid Data Sheet, at least one calendar day before specified start time and date
in key dates for opening of technical proposal as per Key dates in Bid Data Sheet.

Section 2 –Annexure - A

Page 15 of 78
 Annexure – B
(See clause 3 of Section 1 -NIT )

|| AFFIDAVIT ||
(To be Contained in Envelope A)
(On Non Judicial Stamp of Rs. 100)
I/we _______________________________________________________ who is/ are
_______________________ (status in the firm/ company) and competent for submission
of the affidavit on behalf of M/S ______________________ (contractor) do solemnly
affirm an oath and state that:
I/we am/are fully satisfied for the correctness of the certificates/records submitted
in support of the following information in bid documents which are being submitted in
response to notice inviting e-tender No. ______________ for
__________________________ (name of work) dated _______ issued by the
________________ (name of the department).
I/we am/ are fully responsible for the correctness of following self-certified
information/ documents and certificates:
1. That the self-certified information given in the bid document is fully true and
authentic.
2. That:
a. Term deposit receipt deposited as earnest money, demand draft for cost of bid
document and other relevant documents provided by the Bank are authentic.
b. Information regarding financial qualification and annual turnover is correct.
c. Information regarding various technical qualifications is correct.
3. No close relative of the undersigned and our firm/company is working in the
department.
OR
Following close relatives are working in the department:
Name _______________ Post ____________________ Present Posting ___________

Signature with Seal of the Deponent (bidder)

I/ We, _____________________ above deponent do hereby certify that the facts
mentioned in above paras 1 to 4 are correct to the best of my knowledge and belief.
Verified today _____________ (dated) at ______________ (place).

Signature with Seal of the Deponent (bidder)

Note: Affidavit duly notarized in original shall reach at least one calendar day before
opening of the bid.

Section 2 –Annexure - B

Page 16 of 78
 Annexure – D
(See clause 6 of Section 1 -NIT )
SPECIAL ELIGIBILITY CRITERIA

The bidder should have experience of:

A. Erection of Steel Gates - ----------

B. Construction of tunnel - ----------

Note: Above criteria are indicative, subject to suitable stipulations by the

departments and specific bid.

Section 2 –Annexure - D

Page 18 of 78
 Annexure -F
(See clause 3 of section 2-ITB)

Procedure for Participation in e-Tendering

1. Registration of Bidders on e-Tendering System:

All the PWD registered bidders are already registered on the new e-
procurement portal https://www.mpeproc.gov.in. The user id will be the
contractor ID provided to them from MP Online. The password for the new
portal has been sent to the bidders registered email ID. for more details may
th
contact M/s. _Tata Consultancy Services Corporate Block, 5 floor, DB City
BHOPAL-462011 email id: [email protected]. Helpdesk phone
numbers are available on website.

2. Digital Certificate:
The bids submitted online should be signed electronically with a Class III
Digital Certificate to establish the identity of the bidder submitting the bid
online. The bidders may obtain Class III Digital Certificate issued by an
approved Certifying Authority authorized by the Controller of Certifying
Authorities, Government of India. A Class III Digital Certificate is issued upon
receipt of mandatory identity proofs along with an application. Only upon the
receipt of the required documents, a Digital Certificate can be issued. For
details please visit cca.gov.in.

Note:
i. It may take upto 7 working days for issuance of Class III Digital
Certificate; hence the bidders are advised to obtain the certificate at
the earliest. Those bidders who already have valid Class III Digital
Certificate need not obtain another Digital Certificate for the same.
The bidders may obtain more information and the Application From
required to be submitted for the issuance of Digital Certificate from
CCA.GOV.IN

ii. Bids can be submitted till bid submission end date. Bidder will require
digital signature while bid submission.

Section 2 –Annexure - F

Page 23 of 78
 `
The digital certificate issued to the Authorized User of a Partnership firm /
Private Limited Company / Public Limited Company and used for online
biding will be considered as equivalent to a no-objection certificate / power of
attorney to that user.

In case of Partnership firm, majority of the partners have to authorize a

specific individual through Authority Letter signed by majority of the partners
of the firm.
in case of Private Limited Company, Public Limited Company, the Managing
Director has to authorize a specific individual through Authority Letter. Unless
the certificate is revoked, it will be assumed to represent adequate authority of
the specific individual to bid on behalf of the organization for online bids as per
information Technology Act 2000. This Authorized User will be required to
obtain a Digital Certificate. The Digital Signature executed through the use of
Digital Certificate of this Authorized User will be binding on the firm. It shall be
the responsibility of Management / Partners of the concerned firm to inform the
Certifying Authority, if the Authorized User changes, and apply for a fresh Digital
Certificate for the new Authorized User.

3. Set Up of Bidder’s Computer System:

In order for a bidder to operate on the e-tendering System, the Computer
System of the bidder is required to be set up for Operating System, Internet
Connectivity, Utilities, Fonts, etc. The details are available at
https://www.mpeproc.gov.in

4. Key Dates:
The bidders are strictly advised to follow the time schedule (Key Dates) of the
bid on their side for tasks and responsibilities to participate in the bid, as all the
stages of each bid are locked before the start time and date and after the end
time and date for the relevant stage of the bid as set by the Department.

Section 2 –Annexure - F

Page 24 of 78
5. Preparation and Submission of Bids

The bidders have to prepare their bids online, encrypt their bid Data in the
Bid forms and submit Bid of all the envelopes and documents related to the
Bid required to be uploaded as per the time schedule mentioned in the key
dates of the Notice inviting e-Tenders after signing of the same by the Digital
Signature of their authorized representative.

5. Purchase of Bid Document

For purchasing of the bid document bidders have to pay Service Charge online
ONLY which is Rs. [as per Bid Date Sheet]. Cost of bid document is separately
mentioned in the Detailed NIT. The Bid Document shall be available for
purchase to concerned eligible bidders immediately after online release of the
bids and upto scheduled time and date as set in the key dates.
The payment for the cost of bid document shall be made online through
Debit/Credit card , Net banking or NeFT Challan through the payment
gateway provided on the portal.

7 Withdrawal, Substitution and Modification Of Bids

Bidder can withdraw and modify the bid till Bid submission end date.

Section 2 –Annexure - F

Page 25 of 78
 Annexure – G
(See clause 4 of Section 2 -ITB)

JOINT VENTURE (J.V.)

If J.V. is allowed following conditions and requirements must be fulfilled –
1. Bids submitted by a joint venture of two or more firms as partners shall comply with the
following requirements :
a. one of the partners shall be nominated as being Lead Partner, and this authorization shall
be evidenced by submitting a power of attorney signed by legally authorized signatories of
all the partners;
b. the bid and, in case of a successful bid, the Agreement, shall be signed so as to be legally
binding on all partners;
c. the partner in charge shall be authorized to incur liabilities and receive instructions for and
on behalf of any and all partners of the joint venture and the entire execution of the
contract, including payment, shall be done exclusively with the partner in charge;
d. all partners of the joint venture shall be liable jointly and severally for the execution of the
contract in accordance with the contract terms, and a statement to this effect shall be
included in the authorization mentioned under [c] above, as well as in the bid and in the
Agreement [in case of a successful bid];
e. The joint venture agreement should indicate precisely the role of all members of JV in
respect of planning, design, construction equipment, key personnel, work execution, and
financing of the project. All members of JV should have active participation in execution
during the currency of the contract. This should not be varied/modified subsequently
without prior approval of the employer;
f. The joint venture agreement should be registered, so as to be legally valid and binding on
all partners; and
g. a copy of the Joint Venture Agreement entered into by the partners shall be submitted
with the bid.
2. The figures for each of the partners of a joint venture shall be added together to determine
the Bidder’s compliance with the minimum qualifying criteria required for the bid. All the
partners collectively must meet the criteria specified in full. Failure to comply with this
requirement will result in rejection of the joint venture’s bid.
3. The performance security of a Joint Venture shall be in the name of the partner
Lead Partner/joint venture.
4. Attach the power of attorney of the partners authorizing the Bid signatory(ies) on behalf of
the joint venture
5. Attach the agreement among all partners of the joint venture [and which is legally binding
on all partners], which shows the requirements as indicated in the Instructions to Bidders’.
6. Furnish details of participation proposed in the joint venture as below:
DETAILS OF PARTICIPATION IN THE JOINT VENTURE
PARTICIPATION DETAILS FIRM ‘A’ (Lead Partner) FIRM ‘B’ FIRM ‘C’
Financial
Name of the Banker(s)
Planning
Construction Equipment
Key Personnel
Execution of Work
(Give details on contribution of each)

Section 2 –Annexure - G

Page 26 of 78
 Annexure - H
(See clause 12 of Section 2 –ITB & clause 4 of GCC)
ORGANIZATIONAL DETAILS
(To be Contained in Envelope - A)
S.
Particulars Details
No.
Registration number issued by Centralized
1. Registration System of Govt. of M.P. or Proof of (If applicable, scanned copy of proof of
application for registration.
application for registration to be uploaded)
Registration No. _________ Date______
Valid Registration of bidder in appropriate class
2. (Scanned copy of Registration to be
through Centralized Registration of Govt. of MP
uploaded)
Name of Organization/ Individual/ Proprietary
3.
Firm/ Partnership Firm
Entity of Organization
Individual/ Proprietary Firm/ Partnership Firm
4. (Registered under Partnership Act)/ Limited
Company (Registered under the Companies
Act–1956)/ Corporation/ Joint Venture
5. Address of Communication
6. Telephone Number with STD Code
7. Fax Number with STD Code
8. Mobile Number
9. E-mail Address for all communications
Details of Authorized Representative
10. Name
11. Designation
12. Postal Address
13. Telephone Number with STD Code
14. Fax Number with STD Code
15. Mobile Number
16. E-mail Address

Note: In case of partnership firm and limited company certified copy of partnership deed/
Articles of Association and Memorandum of Association along with registration
certificate of the company shall have to be enclosed.
Signature of Bidder with Seal
Date: _____________

Section 2 –Annexure - H

Page 27 of 78
 Annexure – I
(See clause 14 of Section 2 -ITB)

Envelope – B, Technical Proposal

Technical Proposal shall comprise the following documents:

Sno Particulars Details to be submitted

1 Experience – Financial & Physical Annexure - I (Format: I-1)

2 Annual Turnover Annexure - I (Format: I-2)

List of technical personnel for the key

3 Annexure - I (Format: I-3)
positions

List of Key equipments/ machines for

4 Annexure - I (Format: I-4)
quality control labs

List of Key equipments/ machines for

5 Annexure - I (Format: I-5)
construction work

Note:
1. Technical Proposal should be uploaded duly page numbered and indexed.
2. Technical Proposal uploaded otherwise will not be considered.

Section 2 –Annexure - I

Page 28 of 78
 Annexure - I (Format: I-1)
(See clause 14 of Section 2 -ITB)
FINANCIAL & PHYSICAL EXPERIENCE DETAILS
A. Financial Requirement:
The bidder should have completed either of the below:
a) three similar works each costing not less than the amount equal to 20% of the
probable amount of contract during the last 3 financial years; or
b) two similar works each costing not less than the amount equal to 30% of the
probable amount of contract during the last 3 financial years; or
c) one similar work of aggregate cost not less than the amount equal to 50% of the
probable amount of contract in any one financial year during the last 3 financial
years;
To be filled in by the contractor:
i. Details of successfully completed similar works shall be furnished in the following format.
ii. Certificate duly signed by the employer shall also be enclosed for each completed similar
work.

Agreement Number Name of Work Date of Date of Amount of Employer's

& Year Work Order Completion Contract Name and
Address

Existing commitments – (Value of ‘C’ for Bid Capacity formula)

Agreement Name of Date of Date of Amount of Amount of Employer's
Number & Work Work Order Completion Contract balance work Name and
Year Address

B. Physical Requirement:
Execution of similar items of work in any one financial year during the last 3 financial
years should not be less than the minimum physical requirement fixed for the work.
SNo Particulars Actual Quantity Executed
(To be filled in by the contractor)
Year – 1 Year – 2 Year – 3
1 Physical qualification required Yes/ No
2 Earthwork
3 Concrete work

Note: 1. Certificate duly signed by the employer shall be enclosed for the actual quantity
executed in any one year during the last 3 financial years.
2. Similar works: The similarity shall be based on the physical size, complexity, methods
technology or other characteristics of main items of work viz. earth work, cement concrete,
Reinforced cement concrete, brick masonry, stone masonry etc.

Section 2 –Annexure - I (Format I-1)

Page 29 of 78
 Annexure - I (Format: I -2)
(See clause 14 of Section 2 -ITB)
ANNUAL TURN OVER

Requirement:
Average annual construction turnover on the construction works not less than 50% of
the probable amount of contract during the last 5 financial years;

To be filled in by the contractor:

Financial Year Payments received for contracts in progress or completed

Note:
i. Annual turnover of construction should be certified by the Chartered Accountant.
ii. Audited balance sheet including all related notes, and income statements for the above
financial years to be enclosed.

Bid Capacity

Applicants who meet the minimum qualifying criteria in the evaluation as

stated above are to be evaluated further for bid capacity as under:
Bid Capacity = (1.5 A X B) - C
Where

A = Maximum value of civil engineering works executed in any one year during the
last five year (10% weightage per year shall be given to bring the value
of work executed at present price level)
B= Proposed contract period in years.
C= Amount of work in hand at present.

Section 2 –Annexure I (Format I-2)

Page 30 of 78
 Annexure - I (Format: I -3)
(See clause 14 of Section 2 –ITB & Clause 6 of GCC)

List of Technical Personnel for the Key Positions

Minimum requirement Available with the bidder

Name of Personnel
Similar workexperience

Similar workexperience
Minimumrequirement

Total WorkExperience

Total WorkExperience
Qualification

Qualification
Key Position
Key Position
S. No.

S. No.
Age

Age

Section 2 – Annexure I (Format I-3)

Page 31 of 78
 Annexure I (Format: I -4)
(See clause 14 of Section 2 -ITB)
List of Key Equipments/ Machines for Quality Control Labs

Minimum requirement Available with the bidder

Name of Name of
S. No. Equipment/ Quantity
Equi pment/ Qua ntity

Machinery Machinery

Section 2 – Annexure I (Format I-4)

Page 32 of 78
 Annexure - I (Format: I -5)
(See clause 14 of Section 2 -ITB)
List of Key Equipments/ Machines for Construction Work

Minimum requirement Available with the bidder

Name of Name of
S. No. Equipment/ Quantity Equipment/ Quantity
Machinery Machinery

Section 2 – Annexure I (Format I-5)

Page 33 of 78
 Annexure – J
(See clause 14 of Section 2 -ITB)
FINANCIAL BID
(To Be Contained in Envelope-C)
NAME OF WORK __________________________________________________________
________________________________________________________________________
I/We hereby bid for the execution of the above work within the time specified at the
rate (in figures) _______ (in words)___________ _________________________________
percent below/ above or at par based on the Bill of Quantities and item wise rates given
therein in all respects and in accordance with the specifications, designs, drawings and
instructions in writing in all respects in accordance with such conditions so far as
applicable. I/We have visited the site of work and am/ are fully aware of all the difficulties
and conditions likely to affect carrying out the work. I/We have fully acquainted
myself/ourselves about the conditions in regard to accessibility of site and quarries/kilns,
nature and the extent of ground, working conditions including stacking of materials,
installation of tools and plant conditions effecting accommodation and movement of
labour etc. required for the satisfactory execution of contract.
Should this bid be accepted, I/We hereby agree to abide by and fulfill all the terms
and provisions of the said conditions of contract annexed hereto so far as applicable, or in
default thereof to forfeit and pay to the Governor of Madhya Pradesh or his successors in
office the sums of money mentioned in the said conditions.
Note:

i. Only one rate of percentage above or below or at par based on the Bill of Quantities
and item wise rates given therein shall be quoted.
ii. Percentage shall be quoted in figures as well as in words. If any difference in figures
and words is found lower of the two shall be taken as valid and correct rate. If the
bidder is not ready to accept such valid and correct rate and declines to furnish
performance security and sign the agreement his earnest money deposit shall be
forfeited.
iii. In case the percentage "above" or "below" is not given by a bidder, his bid shall be
treated as non-responsive.
iv. All duties, taxes, and other levies payable by the bidder shall be included in the
percentage quoted by the bidder.

Signature of Bidder
Name of Bidder
The above bid is hereby accepted by me on behalf of the Governor of Madhya
Pradesh dated the _________ day of __________ 20__
____________
Signature of Officer by whom accepted

Section 2 –Annexure - J
Page 34 of 78
 Annexure – L
(See clause 21 of Section 2 -ITB)

LETTER OF ACCEPTANCE (LOA)

No. _______________ Dated: ___________
To,
M/s. ___________________________
(Name and address of the contractor)
Subject: _________________________________
(Name of the work as appearing in the bid for the work)

Dear Sir (s),

Your bid for the work mentioned above has been accepted on behalf of the Governor
of Madhya Pradesh at your bided percentage _____ below/ above or at par the Bill of
Quantities and item wise rates given therein.
You are requested to submit within 15 (Fifteen) days from the date of issue of this
letter:
a. The performance security/ performance guarantee of Rs. __________ (in figures)
(Rupees ____________________________________________ in words only).
The performance security shall be in the shape of term deposit receipt/ bank
guarantee of any nationalized / schedule commercial bank valid up to three
months after the expiry of defects liability period.
b. Sign the contract agreement.
Please note that the time allowed for carrying out the work as entered in the bid is
__________ months including/ excluding rainy season, shall be reckoned from the date of
signing the contract agreement.

Signing the contract agreement shall be reckoned as intimation to commencement

of work and no separate letter for commencement of work is required. Therefore, after
signing of the agreement, you are directed to contact the Engineer-in-charge for taking the
possession of site and necessary instructions to start the work.

Yours Faithfully

Executive Engineer

Section 2 –Annexure - L

Page 36 of 78
 Annexure – M
(See clause 22 of Section 2 -ITB)
PERFORMANCE SECURITY
To
_____________________[name of Employer]
_____________________
_____________________[address of Employer]
_____________________

WHEREAS ________________________[name and address of Contractor]

(Hereinafter called "the Contractor") has undertaken, in pursuance of Letter of Acceptance
No.__________ dated ____________ to execute _____________[name of Contract and brief
description of Works] (hereinafter called "the Contract").
AND WHEREAS it has been stipulated by you in the said Contract that the Contractor shall
furnish you with a Bank Guarantee by a recognized bank for the sum specified therein as security
for compliance with his obligation in accordance with the Contract;
AND WHEREAS we have agreed to give the Contractor such a Bank Guarantee:
NOW THEREFORE we hereby affirm that we are the Guarantor and responsible to you on
behalf of the Contractor, up to a total of ___________ [amount of guarantee]* ___________
___(in words), such sum being payable in the types and proportions of currencies in which the
Contract Price is payable, and we undertake to pay you, upon your first written demand and
without cavil or argument, any sum or sums within the limits of _________________[amount of
guarantee] as aforesaid without your needing to prove or to show grounds or reasons for your
demand for the sum specified therein.
We hereby waive the necessity of your demanding the said debt from the
contractor before presenting us with the demand.
We further agree that no change or addition to or other modification of the terms
of the Contract of the Works to be performed there under or of any of the Contract documents
which may be made between you and the Contractor shall in any way release us from any liability
under this guarantee, and we hereby waive notice of any such change, addition or modification.
This guarantee shall be valid until 3 (three) months from the date of expiry of the
Defect Liability Period.

Signature, Name and Seal of the guarantor __________________________________________

Name of Bank ________________________________________________________________
Address __________________________________________________________________
Phone No., Fax No., E-mail Address, of Signing Authority ________________________________
Date _______________________________________________________________________

* An amount shall be inserted by the Guarantor, representing the percentage the Contract
Price specified in the Contract including additional security for unbalanced Bids, if any and
denominated in Indian Rupees.

Section 2 –Annexure - M

Page 37 of 78
 SECTION 3
Conditions of Contract
Part – I General Conditions of Contract [GCC]
Table of Clauses of GCC
Clause Clause
No
Particulars No
Particulars
A. General 21 Payments for Variations and / or Extra
Quantities
1 Definitions 22 No compensation for alterations in or restriction
of work to be carried out.
2 Interpretations and Documents 23 No Interest Payable
3 Language and Law 24 Recovery from Contractors
4 Communications 25 Tax
5 Subcontracting 26 Check Measurements
6 Personnel 27 Termination by Engineer in Charge
7 Force Majeure 28 Payment upon Termination
8 Contractor's Risks 29 Performance Security
9 Liability For Accidents To Person 30 Security Deposit
10 Contractor to Construct the Works 31 Price Adjustment
11 Discoveries 32 Mobilization and Construction Machinery
Advance
12 Dispute Resolution System 33 Secured Advance
B. Time Control 34 Payments Certificates
13 Programme E. Finishing the Contract
14 Extension of Time 35 Completion Certificate
15 Compensation for Delay 36 Final Account
16 Contractor’s quoted percentage F. Other Conditions of Contract
C. Quality Control 37 Currencies
17 Tests 38 Labour
18 Correction of Defects noticed 39 Compliance with Labour Regulations
during the Defect Liability Period
D. Cost Control 40 Audit and Technical Examination
19 Variations - Change in original 41 Death or Permanent Invalidity of Contractor
Specifications, Designs, Drawings
etc.
20 Extra Items 42 Jurisdiction

Section 3 – GCC (Table of Clauses )

Page 38 of 78
 A. General
1. DEFINITIONS
1.1. Bill of Quantities: means the priced and completed Bill of Quantities forming part
of the Bid.
1.2. Chief Engineer: means Chief Engineer of the zone/ basin concerned.
1.3. Completion: means completion of the work as certified by the Engineer-in-Charge,
in accordance with provisions of agreement.
1.4. Contract: means the Contract between the Employer and the Contractor to
execute, complete and/or maintain the work. Agreement is synonym of Contract
and carries the same meaning wherever used.
1.5. Contract Data: means the documents and other information which comprise of the
Contract.
1.6. Contractor: means a person or legal entity whose bid to carry out the work has
been accepted by the Employer.
1.7. Contractor's bid: means the completed bid document submitted by the Contractor
to the Employer.
1.8. Contract amount: means the amount of contract worked out on the basis of
accepted bid.
1.9. Completion of work: means completion of the entire contracted work. Exhaustion
of quantity of any particular item mentioned in the bid document shall not imply
completion of work or any component thereof.
1.10. Day: means the calendar day.
1.11. Defect: means any part of the work not completed in accordance with the
specifications included in the contract.
1.12. Department: means Department of the State Government viz. Water Resources
Department, Public Works Department, Public Health Engineering Department,
Rural Engineering Service and any other organisation which adopts this document.
1.13. Drawings: means drawings including calculations and other information provided
or approved by the Engineer-in-Charge.
1.14. Employer: means the party as defined in the Contract Data, who employs the
Contractor to carry out the work. The Employer may delegate any or all functions
to a person or body nominated by him for specified functions. The word Employer /
Government / Department wherever used denote the Employer.
1.15. Engineer: means the person named in the Contract Data.
1.16. Engineer in charge: means the person named in the Contract Data.

1.17. Equipment: means the Contractor's machinery and vehicles brought temporarily to
the Site for execution of work.
1.18. Government: means Government of Madhya Pradesh.
1.19. In Writing: means communicated in written form and delivered against receipt.
1.20. Material: means all supplies, including consumables, used by the Contractor for
incorporation in the work.

Section 3 –Part - I General Condition of Contract

Page 39 of 78
1.21. Superintending Engineer: means Superintending Engineer-in-Charge of the Circle
concerned.
1.22. Stipulated period of completion: means the period in which the Contractor is
required to complete the work. The stipulated period is specified in the Contract
Data.
1.23. Specification: means the specification of the work included in the Contract and any
modification or addition made or approved by the Engineer-in-Charge.
1.24. Start Date: means the date of signing of agreement for the work.
1.25. Sub-Contractor: means a person or corporate body who has a Contract with the
Contractor, duly authorised to carry out a part of the construction work under the
Contract.
1.26. Temporary Work: means work designed, constructed, installed, and removed by
the Contractor that are needed for construction or installation of the work.
1.27. Tender/Bid, Tenderer/Bidder: are the synonyms and carry the same meaning
where ever used.
1.28. Variation: means any change in the work which is instructed or approved as
variation under this contract.
1.29. Work: The expression "work" or "works" where used in these conditions shall
unless there be something either in the subject or context repugnant to such
construction, be construed and taken to mean the work by virtue of contract,
contracted to be executed, whether temporary or permanent and whether original,
altered, substituted or additional.
2. INTERPRETATIONS AND DOCUMENTS
2.1 Interpretations
In the contract, except where the context requires otherwise:
a. words indicating one gender include all genders;
b. Words indicating the singular also include the plural and vice versa.
c. provisions including the word “agree”, “agreed” or “agreement” require the
agreement to be recorded in writing;
d. written” or “in writing” means hand-written, type-written, printed or
electronically made, and resulting in a permanent record;

2.2 Documents Forming Part of Contract:

1. NIT with all amendments.
2. Instructions to Bidders (ITB, Bid Data Sheet with all Annexures)
3. Conditions of Contract:
i. Part I General Conditions of Contract and the Contract
Data; with all Annexures
ii. Part II Special Conditions of Contract.
4. Specifications
5. Drawings
6. Bill of Quantities
7. Technical and Financial Bid
8. Agreement, and
9. Any other document(s), as specified.

Section 3 –Part - I General Condition of Contract

Page 40 of 78
3. Language and Law
The language of the Contract and the law governing the Contract are stated in the
Contract Data.

4. Communications
All certificates, notice or instruction to be given to the Contractor by
Employer/Engineer shall be sent to the address or contact details given by the
Contractor in [Annexure H of ITB]. The address and contact details for
communication with the Employer/Engineer shall be as per the details given in the
Contract Data. Communication between parties that are referred to in the
conditions shall be in writing. The notice sent by facsimile (fax) or other electronic
means (email) shall also be effective on confirmation of the transmission. The
notice sent by registered post or speed post shall be effective on delivery or at the
expiry of the normal delivery period as undertaken by the postal service. In case of
any change in address for communication, the same shall be immediately notified
to Engineer-in-Charge.

5. Subcontracting
Subcontracting shall be permitted for contracts of value more than amount
specified in the Contract Data with following conditions.
a. The Contractor may subcontract up to 25 percent of the contract price with the
approval of the Employer in writing, but will not assign the Contract.
Subcontracting shall not alter the Contractor's obligations.
b. Following shall not form part of subcontracting:
i. Hiring of labour through a labour contractor.
ii. The purchase of Materials to be incorporated in the works.
iii. Hiring of plant & machinery
c. The sub-contractor will have to be registered in the appropriate category in the
centralised registration system for contractors of the GoMP.

6. Personnel
6.1 The Contractor shall employ for the construction work and routine maintenance
the technical personnel as provided in the Annexure I-3 of Bid Data Sheet, if
applicable. If the Contractor fails to deploy required number of technical staff,
recovery as specified in the Contract Data will be made from the Contractor.
6.2 If the Engineer asks the Contractor to remove a person who is a member of the
Contractor's staff or work force, stating the reasons, the Contractor shall ensure
that the person leaves the Site within three days and has no further connection
with the Works in the Contract.

Section 3 –Part - I General Condition of Contract

Page 41 of 78
7. Force Majeure

7.1 The term “Force Majeure” means an exceptional event or circumstance:

(a) Which is beyond a Party’s control,
(b) Which such Party could not reasonably have provided against before entering
into the Contract,
(c) Which, having arisen, such Party could not reasonably have avoided or
overcome, and
(d) Which is not substantially attributable to the other Party.
Force Majeure may include, but is not limited to, exceptional events or
circumstances of the kind listed below, so long as conditions (a) to (d) above are
satisfied:
(i) War, hostilities (whether war be declared or not), invasion, act of foreign
enemies,
(ii) Rebellion, terrorism, sabotage by persons other than the Contractor’s
Personnel, revolution, insurrection, military or usurped power, or civil war,
(iii) Riot, commotion, disorder, strike or lockout by persons other than the
Contractor’s Personnel,
(iv) Munitions of war, explosive materials, ionising radiation or contamination
by radio-activity, except as may be attributable to the Contractor’s use of
such munitions, explosives, radiation or radio-activity, and
(v) Natural catastrophes such as earthquake, hurricane, typhoon or volcanic
activity.
7.2. In the event of either party being rendered unable by force majeure to perform any
duty or discharge any responsibility arising out of the contract, the relative obligation
of the party affected by such force majeure shall upon notification to the other party
be suspended for the period during which force majeure event lasts. The cost and loss
sustained by either party shall be borne by respective parties.
7.3 For the period of extension granted to the Contractor due to Force Majeure the price
adjustment clause shall apply but the penalty clause shall not apply. It is clarified that
this sub clause shall not give eligibility for price adjustment to contracts which are
otherwise not subject to the benefit of price adjustment clause.
7.4 The time for performance of the relative obligation suspended by the force
majeure shall stand extended by the period for which such cause lasts. Should the
delay caused by force majeure exceed twelve months, the parties to the contract
shall be at liberty to foreclose the contract after holding mutual discussions.

8. Contractor's Risks
8.1 All risks of loss or damage to physical property and of personal injury and death
which arise during and in consequence of the performance of the Contract are the
responsibility of the Contractor.

Section 3 –Part - I General Condition of Contract

Page 42 of 78
 8.2 All risks and consequences arising from the inaccuracies or falseness of the
documents, drawing, designs, other documents and/or information submitted by
the contractor shall be the responsibility of the Contractor alone, notwithstanding
the fact that the designs/ drawings or other documents have been approved by
the department.

9. Liability for Accidents to Person

The contractor shall be deemed to have indemnified and saved harmless the
Government against all action, suits, claims, demands, costs etc. arising in
connection with injuries suffered by any persons employed by the contractor or his
subcontractor for the works whether under the General law or under workman's
compensation Act, or any other statute in force at the time of dealing with the
question of the liability of employees for the injuries suffered by employees and to
have taken steps properly to ensure against any claim there under.

10. Contractor to Construct the Works

10.1 The Contractor shall construct, install and maintain the Works in accordance
with the Specifications and Drawings as specified in the Contract Data.
10.2 In the case of any class of work for which there is no such specification as is
mentioned in Contract Data, such work shall be carried out in accordance with
the instructions and requirement of the Engineer-in-charge.
10.3 The contractor shall supply and take upon himself the entire responsibility of
the sufficiency of the scaffolding, timbering, machinery, tools and implements,
and generally of all means used for the fulfilment of this contract whether such
means may or may not be approved or recommended by the Engineer.

11. Discoveries
Anything of historical or other interest or of significant value unexpectedly
discovered on the Site shall be the property of the Employer. The Contractor shall
notify the Engineer of such discoveries and carry out the Engineer's instructions for
dealing with them.

12. Dispute Resolution System

12.1 No dispute can be raised except before the Competent Authority as defined in
Contract Data in writing giving full description and grounds of dispute. It is
clarified that merely recording protest while accepting measurement and/or
payment shall not be taken as raising a dispute.

Section 3 –Part - I General Condition of Contract

Page 43 of 78
 12.2 No dispute can be raised after 45 days of its first occurrence. Any dispute raised
after expiry of 45 days of its first occurrence shall not be entertained and the
Employer shall not be liable for claims arising out of such dispute.
12.3 The Competent Authority shall decide the matter within 45 days.
12.4 Appeal against the order of the Competent Authority can be preferred within 30
days to the Appellate Authority as defined in the Contract Data. The Appellate
Authority shall decide the dispute within 45 days.
12.5 Appeal against the order of the Appellate Authority can be preferred before the
Madhya Pradesh Arbitration Tribunal constituted under Madhya Pradesh
Madhyastham Adhikaran Adhiniyam, 1983.
12.6 The Contractor shall have to continue execution of the Works with due
diligence notwithstanding pendency of a dispute before any authority or forum.

B. Time Control
13. Programme
13.1 Within the time stated in the Contract Data, the Contractor shall submit to the
Engineer for approval a Programme showing the general methods,
arrangements, order and timing for all the activities for the construction of
works.
13.2 The program shall be supported with all the details regarding key personnel,
equipment and machinery proposed to be deployed on the works for its
execution. The contractor shall submit the list of equipment and machinery
being brought to site, the list of key personnel being deployed, the list of
machinery/equipment being placed in field laboratory and the location of field
laboratory along with the Programme.
13.3 An update of the Programme shall be a programme showing the actual progress
achieved on each activity and the effect of the progress achieved on the timing
of the remaining Works, including any changes to the sequence of the activities.
13.4 The Contractor shall submit to the Engineer for approval an updated
Programme at intervals no longer than the period stated in the Contract Data. If
the Contractor does not submit an updated Programme within this period, the
Engineer may withhold the amount stated in the Contract Data from the next
payment certificate and continue to withhold this amount until the next
payment after the date on which the overdue Programme has been submitted.
13.5 The Engineer's approval of the Programme shall not alter the Contractor's
obligations.

Section 3 –Part - I General Condition of Contract

Page 44 of 78
14. Extension of Time
14.1. If the Contractor desires an extension of time for completion of the work on the
ground of his having been unavoidably hindered in its execution or on any other
grounds, he shall apply, in writing, to the Engineer-in-charge, on account of
which he desires such extension. Engineer-in-Charge shall forward the
aforesaid application to the Competent Authority as prescribed.
14.2 The competent authority shall grant such extension at each such occasion
within a period of 30 days of receipt of application from contractor and shall not
wait for finality of work. Such extensions shall be granted in accordance with
provisions under clause- 15 of this agreement.
14.3 In case the work is already in progress, the Contractor shall proceed with the
execution of the works, including maintenance thereof, pending receipt of the
decision of the competent authority as aforesaid with all due diligence.

15. Compensation for delay

15.1 The time allowed for carrying out the work, as entered in the agreement, shall
be strictly observed by the Contractor.
15.2 The time allowed for execution of the contract shall commence from the date
of signing of the agreement. It is clarified that the need for issue of work order
is dispensed with.
15.3 In the event milestones are laid down in the Contract Data for execution of the
works, the contractor shall have to ensure strict adherence to the same.
15.4 Failure of the Contractor to adhere to the timelines and/or milestones shall
attract such liquidated damages as is laid down in the Contract Data.
15.5 In the event of delay in execution of the Works as per the timelines mentioned
in the Contract Data the Engineer-in-charge shall retain from the bills of the
Contractor amount equal to the liquidated damages leviable until the
Contractor makes such delays good. However, the Engineer-in-charge shall
accept bankable security in lieu of retaining such amount.
15.6 If the Contractor is given extension of time after liquidated damages have been
paid, the Engineer in Charge shall correct any over payment of liquidated
damages by the Contractor in the next payment certificate.
15.7 In the event the Contractor fails to make good the delay until completion of the
stipulated contract period (including extension of time) the sum so retained
shall be adjusted against the liquidated damages levied.
16. Contractor's quoted percentage
The Contractor’s quoted percentage rate referred to in the "Bid for works" will be
deducted/ added from/to the net amount of the bill after deducting the cost of
material supplied by the department.

Section 3 –Part - I General Condition of Contract

Page 45 of 78
 C. Quality Control
17. Tests
17.1 The Contractor shall be responsible for:
a. Carrying out the tests prescribed in specifications, and
b. For the correctness of the test results, whether preformed in his laboratory
or elsewhere.
17.2 The contractor shall have to establish field laboratory within the time specified
and having such equipments as are specified in the Contract Data.
17.3 Failure of the Contractor to establish laboratory shall attract such penalty as is
specified in the Contract Data.

18. Correction of Defects noticed during the Defect Liability Period

18.1 The Defect Liability Period of work in the contract shall be as per the Contract
Data.
18.2 The Contractor shall promptly rectify all defects pointed out by the Engineer
well before the end of the Defect Liability Period. The Defect Liability Period
shall automatically stand extended until the defect is rectified.
18.3 If the Contractor has not corrected a Defect pertaining to the Defect Liability
Period to the satisfaction of the Engineer, within the time specified by the
Engineer, the Engineer will assess the cost of having the Defect corrected, and
the cost of correction of the Defect shall be recovered from the Performance
Security or any amount due or that may become due to the contractor and
other available securities.
D. Cost Control

19. Variations - Change in original Specifications, Designs, and Drawings etc.

19.1 The Engineer-in-charge shall have power to make any alterations, omissions or
additions to or substitutions in the original specifications, drawings, designs and
instructions, that may appear to him to be necessary during the progress of the
work and the contractor shall carry out the work in accordance with any
instructions which may be given to him in writing signed by the Engineer-in-
charge, and such alterations, omission, additions or substitutions shall not
invalidate the contract and any altered, additional or substituted work, which
the contractor may be directed to do in the manner above specified, as part of
the work, shall be carried out by the contractor on the same conditions in all
respects on which he agrees to do the main work.

Section 3 –Part - I General Condition of Contract

Page 46 of 78
 19.2 The time for the completion of the work shall be adjusted in the proportion that
the altered, additional or substituted work bears to the original contract work
and the certificate of the Engineer-in-charge shall be conclusive as to such
proportion.

20. Extra items

20.1 All such items which are not included in the priced BOQ shall be treated as extra
items.

21. Payments for Variations and / or Extra Quantities

21.1 The rates for such additional (Extra quantity), altered or substituted work /
extra items under this clause shall be worked out in accordance with the
following provisions in their respective order:-

a. The contractor is bound to carry out the additional (Extra quantity), work at
the same rates as are specified in the contract for the work.

b. If the item is not in the priced BOQ and is included in the SOR of the
department, the rate shall be arrived at by applying the quoted tender
percentage on the SOR rate.

c. If the rates for the altered or substituted work are not provided in
applicable SOR - such rates will be derived from the rates for a similar class
(type) of work as is provided in the contract (priced BOQ) for the work.

d. If the rates for the altered, substituted work cannot be determined in the
manner specified in the sub clause (c) above - then the rates for such
composite work item shall be worked out on the basis of the concerned
Schedule of Rates minus/plus the percentage quoted by the contractor.

e. If the rates for a particular part or parts of the item is not in the Schedule of
Rates and the rates for the altered, or substituted work item cannot be
determined in the manner specified in sub clause (b) to (d) above, the rate
for such part or parts will be determined by the Competent Authority as
defined in the Contract Data on the basis of the rate analysis derived out of
prevailing market rates when the work was done.

Section 3 –Part - I General Condition of Contract

Page 47 of 78
 f. But under no circumstances, the contractor shall suspend the work on the
plea of non-acceptability of rates on items falling under sub clause (a) to (d).
In case the contractor does not accept the rate approved by the Engineer in
Charge for a particular item, the contractor shall continue to carry out the
item at the rates determined by the Competent Authority. The decision on
the final rates payable shall be arrived at through the dispute settlement
procedure.

22. No compensation for alterations in or restriction of work to be carried out.

22.1 If at any time after the commencement of the work, the Engineer-in-charge, for
any reason whatsoever, not require the whole or any part of the work as
specified in the bid to be carried out; the Engineer-in-charge shall give notice in
writing of the fact to the Contractor and withdraw that whole or any part of the
work.
22.2 The Contractor shall have no claim to any payments or compensation
whatsoever, on account of any profit or advantage which he might have derived
from the execution of work in full or on account of any loss incurred for idle
men and machinery due to any alteration or restriction of work for whatsoever
reason.
22.3 The Engineer-in-charge may supplement the work by engaging another agency
to execute such portion of the work, without prejudice to his rights.
23. No Interest Payable
No interest shall be payable to the Contractor on any payment due or awarded
by any authority.
24. Recovery from Contractors
Whenever any claim against the Contractor for the payment arises under the
contract, the Department may be entitled to recover such sum by:
(a) Appropriating, in part or whole of the Performance Security and Additional
Performance Security, if any; and/or Security Deposit and / or any sums payable
under the contract to the contractor.
(b) If the amount recovered in accordance with (a) above is not sufficient, the
balance sum may be recovered from any payment due to the contractor under
any other contract of the department, including the securities which become
due for release.
(c) The department shall, further have an additional right to effect recoveries as
arrears of land revenue under the M.P. Land Revenue Code.
25. Tax
25.1 The rates quoted by the Contractor shall be deemed to be inclusive of the
commercial tax and other levies, duties, cess, toll, taxes of Central and State
Governments, local bodies and authorities.

Section 3 –Part - I General Condition of Contract

Page 48 of 78
 25.2 The liability, if any, on account of quarry fees, royalties, octroi and any other
taxes and duties in respect of materials actually consumed on public work,
shall be borne by the Contractor.

25.3 Any changes in the taxes due to change in legislation or for any other reason
shall not be payable to the contractor.

26. Check Measurements

26.1 The department reserves to itself the right to prescribe a scale of check
measurement of work in general or specific scale for specific works or by other
special orders.
26.2 Checking of measurement by superior officer shall supersede measurements by
subordinate officer(s), and the former will become the basis of the payment.
26.3 Any over/excess payments detected, as a result of such check measurement or
otherwise at any stage up to the date of completion of the defect liability period
specified in this contract, shall be recoverable from the Contractor, as per
clause 24 above.

27. Termination by Engineer in Charge

27.1 If the Contractor fails to carry out any obligation under the Contract, the
Engineer in Charge may by notice require the Contractor to make good the
failure and to remedy it within a specified reasonable time.
27.2 The Engineer in Charge shall be entitled to terminate the Contract if the
Contractor
a) abandons the Works or otherwise plainly demonstrates the intention not to
continue performance of his obligations under the Contract;
b) the Contractor is declared as bankrupt or goes into liquidation other than
for approved reconstruction or amalgamation;
c) without reasonable excuse fails to comply with the notice to correct a
particular defect within a reasonable period of time;
d) the Contractor does not maintain a valid instrument of financial security as
prescribed;
e) the Contractor has delayed the completion of the Works by such duration
for which the maximum amount of liquidated damages is recoverable;
f) If the Contractor fails to deploy machinery and equipment or personnel or
set up a field laboratory as specified in the Contract Data;
g) If the contractor, in the judgment of the Engineer in charge has engaged in
corrupt or fraudulent practices in competing for or in executing the contract;
h) Any other fundamental breaches as specified in the Contract Data.

Section 3 –Part - I General Condition of Contract

Page 49 of 78
 27.3 In any of these events or circumstances, the Engineer in Charge may, upon
giving 14 days’ notice to the Contractor, terminate the Contract and expel the
Contractor from the Site. However, in the case of sub-paragraph (b) or (g) of
clause 27.2, the Engineer in Charge may terminate the Contract immediately.
27.4 Notwithstanding the above, the Engineer-in-Charge may terminate the Contract
for convenience by giving notice to the Contractor.

28. Payment upon Termination

28.1 If the contract is terminated under clause 27.3, the Engineer shall issue a
certificate for value of the work accepted on final measurements, less Advance
Payments and Penalty as indicated in the Contract Data. The amount so arrived
at shall be determined by the Engineer-in-Charge and shall be final and binding
on both the parties.
28.2 Payment on termination under clause 27. 4 above -
If the Contract is terminated under clause 27.4 above, the Engineer shall issue a
certificate for the value of the work done, the reasonable cost of removal of
Equipment, repatriation of the Contractor's personnel employed solely on the
Works, and the Contractor's costs of protecting and securing the Works and less
advance payments received up to the date of the certificate, less other
recoveries due in terms of the contract and less taxes due to be deducted at
source as per applicable law.
28.3 If the total amount due to the Employer exceeds any payment due to the
Contractor, the difference shall be recovered as per clause 24 above.

29. Performance Security

The Contractor shall have to submit performance security and additional
performance security, if any, as specified in the Bid Data Sheet at the time of
signing of the contract. The contractor shall have to ensure that such performance
security and additional performance security, if any, remains valid for the period as
specified in the Contract Data.

30. Security Deposit-

30.1 Security Deposit shall be deducted from each running bill at the rate as specified in
the Contract Data. The total amount of Security Deposit so deducted shall not
exceed the percentage of Contract Price specified in the Contract Data.
30.2 The security deposit may be replaced by equivalent amount of bank guarantee
or fixed deposit receipt assigned to the Employer, with validity up to 3 (three)
months beyond the completion of Defect Liability Period/ extended Defect
Liability Period.
30.3 The Security Deposit shall be refunded on completion of Defect Liability Period.

Section 3 –Part - I General Condition of Contract

Page 50 of 78
31. Price Adjustment
31.1 Applicability
1. Price adjustment shall be applicable only if provided for in the Contract Data.
2. The price adjustment clause shall apply only for the works executed from
the date of signing of the agreement until the end of the initial intended
completion date or extensions granted for reasons attributed to the
Employer by the Engineer.
3. The Contractor shall not be entitled to any benefit arising from the price
adjustment clause for extension in the contract period for reasons
attributed to the Contractor.
4. In the Force Majeure event the price escalation clause shall apply.

31.2 Procedure

1. Contract price shall be adjusted for increase or decrease in rates and price
of labour, materials, fuels and lubricants in accordance with following
principles and procedures and as per formula given in the contract data.

2. The price adjustable shall be determined during each quarter from the
formula given in the contract data.

3. Following expression and meaning are assigned to the work done during
each quarter:

R = Total value of work during the quarter. It would include the amount of secured
advance granted, if any, during the quarter, less the amount of secured advance
recovered, if any during the quarter, less value of material issued by the
department, if any, during the quarter.

4. Weightages of various components of the work shall be as per the Contract

Data.

31.3 To the extent that full compensation for any rise or fall in costs to the
contractor is not covered by the provisions of this or other clauses in the
contract, the unit rates and prices included in the contract shall be deemed to
include amounts to cover the contingency of such other rise or fall in costs.

31.4 The index relevant to any quarter, for which such compensation is paid, shall be
the arithmetical average of the indices relevant of the calendar month.
31.5 For the purpose of clarity it is pointed out that the price adjustment may be either
positive or negative, i.e. if the price adjustment is in favour of the Employer, the
same shall be recovered from the sums payable to the Contractor.

Section 3 –Part - I General Condition of Contract

Page 51 of 78
32. Mobilization and Construction Machinery Advance

32.1 Payment of advances shall be applicable if provided in the Contract Data.

32.2 If applicable, the Engineer in Charge shall make interest bearing advance
payment to the contractor of the amounts stated in the Contract Data, against
provision by the contractor of an unconditional Bank Guarantee in a form and
by a nationalized/ scheduled banks, in the name as stated in the Contract Data,
in amounts equal to the advance payment. The guarantee shall remain effective
until the advance payment has been repaid, but the amount of the guarantee
shall be progressively reduced by the amounts repaid by the contractor.
32.3 The rate of interest chargeable shall be as per Contract Data.
32.4 The construction machinery advance, if applicable, shall be limited to 80% of
the cost of construction machinery and admissible only for new construction
machinery.
32.5 The advance payment shall be recovered as stated in the Contract Data by
deducting proportionate amounts from payment otherwise due to the
Contractor. No account shall be taken of the advance payment or its recovery in
assessing valuations of work done, variations, price adjustments, compensation
events, or liquidated damages.

33. Secured Advance

33.1 Payment of Secured Advance shall be applicable if provided in the Contract Data.
33.2 If applicable, the Engineer shall make advance payment against materials
intended for but not yet incorporated in the Works and against provision by the
contractor of an unconditional Bank Guarantee in a form and by a nationalized/
scheduled bank, in the name as stated in the Contract Data, in amounts equal
to the advance payment. The guarantee shall remain effective until the advance
payment has been adjusted, but the amount of the guarantee shall be
progressively reduced by the amounts adjusted by the contractor.
33.3 The amount of secured advance and conditions to be fulfilled shall be as
stipulated in the Contract Data.
33.4 The Secured Advance paid shall be recovered as stated in the Contract Data.

34. Payment Certificates

The payment to the contractor will be as follows for construction work:
(a) The Contractor shall submit to the Engineer monthly statements of the value of
the work executed less the cumulative amount certified previously, supported
with detailed measurement of the items of work executed.
(b) The Engineer shall check the Contractor’s monthly statement and certify the
amount to be paid to the Contractor.

Section 3 –Part - I General Condition of Contract

Page 52 of 78
 (c) The value of work executed shall be determined, based on the measurements
approved by the Engineer/ Engineer-in-charge.

(d) The value of work executed shall comprise the value of the quantities of the
items in the Bill of Quantities completed.

(e) The value of work executed shall also include the valuation of Variations
and Compensation Events.

(f) All payments shall be adjusted for deductions for advance payment, security
deposit, other recoveries in terms of contract and taxes at source as applicable
under the law.

(g) The Engineer may exclude any item certified in a previous certificate or reduce
the proportion of any item previously certified in any certificate in the light of
later information.

(h) Payment of intermediate certificate shall be regarded as payments by way of

advance against the final payment and not as payments for work actually done
and completed.

(i) Intermediate payment shall not preclude the requiring of bad, unsound and
imperfect or unskilled work to be removed and taken away and reconstructed
or be considered as an admission of the due performance of the contractor any
part thereof, in any respect or the occurring of any claim.
(j) The payment of final bill shall be governed by the provisions of clause 36 of GCC.

E. Finishing the Contract

35. Completion Certificate

35.1 A Completion Certificate in the prescribed format in Contract Data shall be
issued by the Engineer-in-Charge after physical completion of the Work.
35.2 After final payment to the Contractor, a Final Completion Certificate in the
prescribed format in the Contract Data shall be issued by the Engineer-in-
Charge.

Section 3 –Part - I General Condition of Contract

Page 53 of 78
36. Final Account

36.1 The Contractor shall supply the Engineer with a detailed account of the total
amount that the Contractor considers payable for works under the Contract
within 21 days of issue of certificate of physical completion of works. The
Engineer shall issue a Defects Liability Certificate and certify any payment that is
due to the Contractor within 45 days of receiving the Contractor’s account if it is
correct and complete. If the account is not correct or complete, the Engineer
shall issue within 45 days a schedule that states the scope of the corrections or
additions that are necessary. If the Account is still unsatisfactory after it has
been resubmitted, the matter shall be referred to the Competent Authority as
defined in the Contract Data, who shall decide on the amount payable to the
Contractor after hearing the Contractor and the Engineer in Charge.

36.2 In case the account is not received within 21 days of issue of Certificate of
Completion as provided in clause 35.1 above, the Engineer shall proceed to
finalise the account and issue a payment certificate within 28 days.

F. Other Conditions of Contract

37. Currencies
All payments will be made in Indian Rupees.
38. Labour

38.1 The Contractor shall, unless otherwise provided in the Contract, make his own
arrangements for the engagement of all staff and labour, local or other, and for
their payment, housing, feeding and transport.

38.2 The Contractor shall, if required by the Engineer, deliver to the Engineer a
return in detail, in such form and at such intervals as the Engineer may
prescribe, showing the staff and the numbers of the several classes of labour
from time to time employed by the Contractor on the Site and such other
information as the Engineer may require.

Section 3 –Part - I General Condition of Contract

Page 54 of 78
39. Compliance with Labour Regulations
39.1. During continuance of the Contract, the Contractor and his sub-Contractors shall
abide at all times by all existing labour enactments and rules made there under,
regulations, notifications and bye laws of the State or Central Government or local
authority and any other labour law (including rules), regulations, bye laws that may
be passed or notification that may be issued under any labour law in future either
by the State or the Central Government or the local authority. Salient features of
some of the major labour laws that are applicable to construction industry are
given in the Contract Data. The Contractor shall keep the Employer indemnified in
case any action is taken against the Employer by the competent authority on
account of contravention of any of the provisions of any Act or rules made their
under, regulations or notifications including amendments. If the Employer is caused
to pay or reimburse, such amounts as may be necessary to cause or observe, or for
non-observance of the provisions stipulated in the
notifications/byelaws/Acts/Rules/ regulations including amendments, if any, on the
part of the Contractor, the Engineer/Employer shall have the right to deduct from
any money due to the Contractor including his amount of performance security.
The Employer/Engineer shall also have right to recover from the Contractor any
sum required or estimated to be required for making good the loss or damage
suffered by the Employer. The employees of the Contractor and the Sub-Contractor
in no case shall be treated as the employees of the Employer at any point of time.

40. Audit and Technical Examination

Government shall have the right to cause an audit and technical examination of the
works and the final bill of the contract including all supporting vouchers, abstract etc.
to be made after payment of the final bill and if as a result of such audit and technical
examination any sum is found to have been overpaid in respect of any work done by
the contractor under the contract or any work claimed by him to have been done
under the contract and found not to, have been executed, the Contractor shall be
liable to refund the amount of overpayment and it shall be lawful for Government to
recover the same from him in the manner prescribed in clause 24 above and if it is
found that the Contractor was paid less than what was due to him, under the
contract in respect of any work executed by him under it, the amount of such under
payment shall be duly paid by Government to the Contractor.

Section 3 –Part - I General Condition of Contract

Page 55 of 78
41. Death or Permanent Invalidity of Contractor
If the Contractor is an individual or a proprietary concern, partnership concern, dies
during the currency of the contract or becomes permanently incapacitated, where
the surviving partners are only minors, the contract shall be closed without levying
any damages/ compensation as provided for in clause 28.2 of the contract
agreement. However, if the competent authority is satisfied about the competence
of the survivors, then the competent authority shall enter into a fresh agreement for
the remaining work strictly on the same terms and conditions under which the
contract was awarded.

42. Jurisdiction
This contract has been entered into the State of Madhya Pradesh and its validity,
construction, interpretation and legal effect shall be subjected to the courts at the
place where this agreement is entered into. No other jurisdiction shall be applicable.
[End of GCC]

Section 3 –Part - I General Condition of Contract

Page 56 of 78
 ANNEXURE – N
(See clause 10 of Section 3 – GCC )

Drawings
List of drawings –

Section 3 – Annexure N

Page 60 of 78
 ANNEXURE – P
(See clause 15 of Section 3 -GCC )

Compensation for Delay

If the contractor fails to achieve the milestones, and the delay in execution of work
is attributable to the contractor, the Employer shall retain an amount from the
sums payable and due to the contractor as per following scale -

i. Slippage up to 25% in financial target during the milestone under consideration

— 2.5% of the work remained unexecuted in the related time span.

ii. Slippage exceeding 25% but Up to 50% in financial target during the
milestone under consideration
- 5% of the work remained unexecuted in the related time span..

iii. Slippage exceeding 50% but Up to 75% in financial target during the
milestone under consideration
-7.5% of the work remained unexecuted in the related time span..

iv. Slippage exceeding 75% in financial target during the milestone

under consideration
-10% of the work remained unexecuted in the related time span.

Note: For arriving at the dates of completion of time span related to different milestones,
delays which are not attributable to the Contractor shall be considered. The slippage
on any milestone is if made good in subsequent milestones or at the time of stipulated
period of completion, the amount retained as above shall be refunded. In case the
work is not completed within the stipulated period of completion along with all such
extensions which are granted to the Contractor for either Employer’s default or Force
Majeure, the compensation shall be levied on the contractor at the rate of 0.05% per
day of delay limited to a maximum of 10% of contract price.

The decision of Superintending Engineer shall be final and binding upon both
the parties.

Section 3 – Annexure P

Page 62 of 78
 ANNEXURE - R
(See clause 31 of Section 3 -GCC )
Price Adjustment

The formulas for adjustment of price are as follow:

R = Value of work as defined in Clause 31.2(3) of General Conditions of Contract

Weightages* of component in the work

Percentage of
S.No Component
component in the work
1 Cement - Pc
2 Steel - Ps
3 Bitumen - Pb
4 POL - Pf

* Weightages of various components of the work shall be as determined by

the competent technical sanction authority.

Adjustment for cement component

(ii) Price adjustment for increase or decrease in the cost of

cement procured by the contractor shall be paid in
accordance with the following formula:
VC= 0.85 x PC/100 x R x (C1-C0)/C0
Vc= increase or decrease in the cost of work during the month under
Consideration due to changes in rates for cement.
Co= The all India wholesale price index for Grey cement on the date of opening of
Bids as published by the Ministry of Industrial Development, Government of
India, New Delhi. (www.eaindustry.nic.in)
C1= The all India average wholesale price index for Grey cement for the month
under consideration as published by Ministry of Industrial Development,
Government of India, New Delhi.(www.eaindustry.nic.in)
Pc= Percentage of cement component of the work

Note : For the application of this clause, index of Grey Cement has been chosen to
represent Cement group.

Adjustment of steel component

(iii) Price adjustment for increase or decrease in the cost of steel procured by
the Contractor shall be paid in accordance with the following formula:

Section 3 – Annexure R

Page 64 of 78
 Vs= 0.85 x PS x /100 x R x (S1-S0)/S0
Vs= Increase or decrease in the cost of work during the month under consideration
due to changes in the rates for steel.
S0= The all India wholesale price index for steel (Bars and Rods) on the date of
opening of Bids as published by the Ministry of Industrial Development,
Government of India, New Delhi. (www.eaindustry.nic.in)
Si = The all India average wholesale price index for steel (Bars and Rods) for the
month under consideration as published by Ministry of Industrial
Development, New Delhi. (www.eaindustry.nic.in)
Ps= Percentage of steel component of the work.

Note : For the application of this clause, index of Bars and Rods has been chosen to
represent steel group.
Adjustment of bitumen component

(iv) Price adjustment for increase or decrease is the cost of bitumen shall be paid
in accordance with the following formula:
Vb= 0.85x Pb / 100xRx( Bi – Bo) / Bo
Vb= Increase or decrease in the cost of work during the month under
consideration due to changes in rates for bitumen.
Bo = The official retail price of bitumen at the IOC depot at nearest
center on the date of opening of Bids.
Bi = The official retail price of bitumen of IOC depot at nearest center for
th
the 15 day of the month under consideration.
Pb = Percentage of bitumen component of the work.

Adjustment of POL (fuel and lubricant) component

( V) Price adjustment for increase or decrease in cost of POL ( fuel and lubricant )
shall be paid in accordance with the following formula:

Vf= 0.85 x Pf / 100 x R x ( Fi – Fo) / Fo

Vf = Increase or decrease in the cost of work during the month under

consideration due to changes in rates for fuel and lubricants.
Fo = The official retail price of High Speed Diesel (HSD) at the existing
consumer pumps of IOC at nearest center on the date of opening of
Bids.
Fi = The official retail price of HSD at the existing consumer pumps of IOC at
th
nearest center for the 15 day of month of the under consideration.
Pf = Percentage of fuel and lubricants component of the work.

Note : For the application of this clause, the price of High Speed Diesel has been
chosen to represent fuel and lubricants group.

Section 3 – Annexure R

Page 65 of 78
 Annexure – S
(See clause 32 of Section 3 -GCC )

Bank Guarantee Form for Mobilization and Construction Machinery Advance

To
_____________________[name of Employer]
_____________________[address of Employer]
_____________________[name of Contractor]
In accordance with the provisions of the General Conditions of Contract, clause 31
("Mobilization and Construction Machinery Advance") of the above-mentioned Contract
__________________[name and address of Contractor] (hereinafter called "the
Contractor") shall deposit with ______________ [name of Employer] a bank guarantee to
guarantee his proper and faithful performance under the said Clause of the Contract in an
amount of ___________________[amount of Guarantee]* ____________________[in
words].
We, the _______________[bank of financial institution], as instructed by the
Contractor, agree unconditionally and irrevocably to guarantee as primary obligator and
not as surety merely, the payment to _________________[name of Employer] on his first
demand without whatsoever right of obligation on our part and without his first claim to
the Contractor, in the amount not exceeding ____________[amount of guarantee]*
___________________________[in words].
We further agree that no change or addition to or other modification of the terms of
the Contractor or Works to be performed thereunder or of any of the Contract documents
which may be made between __________________[name of Employer] and the
Contractor, shall in any way release us from any liability under this guarantee, and we
hereby waive notice of any such change, addition or modification.
This guarantee shall remain valid and in full effect from the date of the advance
payment under the Contract until _________________ [name of Employer] receives full
repayment of the same amount from the Contractor.
Yours truly, Signature
and Seal : ____________________________
Name of Bank/Financial Institution: ________________
Address : _____________________________________
Date : ____________
_______________________________________________________________
* An amount shall be inserted by the Bank or Financial Institution representing
the amount of the Advance Payment, and denominated in Indian Rupees.

Section 3 – Annexure S

Page 66 of 78
 Annexure – T
(See clause 33 of Section 3 -GCC )

Bank Guarantee Form for Secured Advance

INDENTURE FOR SECURED ADVANCES

This indenture made the ___________ day of __________ 20___ BETWEEN

____________ (hereinafter called the contractor which expression shall where the context
so admits or implies be deemed to include his executors, administrators and assigns) or
the one part and the Employer of the other part.

Whereas by an agreement dated ______________ (hereinafter called the

said agreement) the contractor has agreed.

AND WHEREAS the contractor has applied to the Employer that he may be
allowed advanced on the security of materials absolutely belonging to him and brought by
him to the site of the works the subject of the said agreement for use in the construction
of such of the works as he has undertaken to executive at rates fixed for the finished work
(inclusive of the cost of materials and labour and other charges)

AND WHEREAS the Employer has agreed to advance to the Contractor the sum
of Rupees _________________________ on the security of materials the quantities and other
particulars of which are detailed in Accounts of Secured Advance attached to the Running
Account Bill for the said works signed by the Contractor on _________ and the Employer has
reserved to himself the option of making any further advance or advances on the security of
other materials brought by the Contractor to the site of the said works.

Now THIS INDENTURE WITNESSETH that in pursuance of the said agreement

and in consideration of the sum of Rupees ___________ on or before the execution of
these presents paid to the Contractor by the Employer (the receipt where of the
Contractor doth hereby acknowledge) and of such further advances (if any) as may be
made to him as a for said the Contractor doth hereby covenant and agree with the
President and declare as follows:
That the said sum of Rupees ________________ so advanced by the Employer to

Section 3 – Annexure T

Page 67 of 78
(1) the Contractor as aforesaid and all or any further sum of sums advanced as
aforesaid shall be employed by the Contractor in or towards expending the
execution of the said works and for no other purpose whatsoever.

(2) That the materials details in the said Account of Secured Advances which have been
offered to and accepted by the Employer as security are absolutely the Contractor's
own propriety and free from encumbrances of any kind and the contractor will not
make any application for or receive a further advance on the security of materials
which are not absolutely his own property and free from encumbrances of any kind
and the Contractor indemnified the Employer against all claims to any materials in
respect of which an advance has be made to him as aforesaid.
(3) That the materials detailed in the said account of Secured Advances and all other
materials on the security of which any further advance or advances may hereafter
be made as aforesaid (hereafter called the said materials) shall be used by the
Contractor solely in the execution of the said works in accordance with the
directions of the Engineer.
(4) That the Contractor shall make at his own cost all necessary and adequate
arrangements for the proper watch, safe custody and protection against all risks of
the said materials and that until used in construction as aforesaid the said materials
shall remain at the site of the said works in the Contractor's custody and on his
own responsibility and shall at all times be open to inspection by the Engineer or
any officer authorized by him. In the event of the said materials or any part thereof
being stolen, destroyed or damaged or becoming deteriorated in a greater degree
than is due to reasonable use and wear thereof the Contractor will forthwith
replace the same with other materials of like quality or repair and make good the
same required by the Engineer.
(5) That the said materials shall not be removed from the site of the said works except
with the written permission of the Engineer or an officer authorized by him on that
behalf.

Section 3 – Annexure T

Page 68 of 78
(6) That the advances shall be repayable in full when or before the Contract receives
payment from the Employer of the price payable to him for the said works under
the terms and provisions of the said agreement. Provided that if any intermediate
payments are made to the Contractor on account of work done than on the
occasion of each such payment the Employer will be at liberty to make a recovery
from the Contractor's bill for such payment by deducting there from the value of
the said materials than actually used in the construction and in respect of which
recovery has not been made previously, the value for this purpose being
determined in respect of each description of materials at the rates at which the
amounts of the advances made under these presents were calculated.

(7) That if the Contractor shall at any time make any default in the performance or
observance in any respect of any of the terms and provisions of the said agreement
or of these presents the total amount of the advance or advances that may still be
owing of the Employer shall immediately on the happening of such default be re-
payable by the Contractor to be the Employer together with interest thereon at
twelve percent per annum from the date or respective dates of such advance or
advances to the date of repayment and with all costs, charges, damages and
expenses incurred by the Employer in or for the recovery thereof or the
enforcement of this security or otherwise by reason of the default of the
Contractor and the Contractor hereby covenants and agrees with the Employer to
reply and pay the same respectively to him accordingly.

(8) That the Contractor hereby charges all the said materials with the repayment to
the Employer of the said sum of Rupees____________________________ and any
further sum of sums advanced as aforesaid and all costs, charges, damages and
expenses payable under these presents PROVIDED ALWAYS and it is hereby agreed
and declared that notwithstanding anything in the said agreement and without
prejudice to the power contained therein if and whenever the covenant for
payment and repayment here-in-before contained shall become enforceable and
the money owing shall not be paid in accordance there with the Employer may at
any time thereafter adopt all or any of the following courses as he may deem best:

Section 3 – Annexure T

Page 69 of 78
 (a) Seize and utilise the said materials or any part thereof in the completion of the
said works on behalf of the contractor in accordance with the provision in that
behalf contained in the said agreement debiting the contractor with the actual
cost of effecting such completion and the amount due to the contractor with
the value of work done as if he had carried it out in accordance with the said
agreement and at the rates thereby provided. If the balance is against the
contractor, he is to pay same to the Employer on demand.

(b) Remove and sell by public auction the seized materials or any part thereof and
out of the moneys arising from the sale retain all the sums aforesaid repayable
or payable to the Employer under these presents and pay over the surplus (if
any) to the Contractor.

(C) Deduct all or any part of the moneys owing out of the security deposit or any
sum due to the Contractor under the said agreement.

(9) That except in the event of such default on the part of the contractor as aforesaid
interest on the said advance shall not be payable.

(10) That in the event of any conflict between the provisions of these presents and the
said agreement the provisions of these presents shall prevail and in the event of
any dispute or difference arising over the construction or effect of these presents
the settlement of which has not been here-in-before expressly provided for the
same shall be referred to the Employer whose decision shall be final and the
provision of the Indian Arbitration Act for the time being in force shall apply to any
such reference.

Section 3 – Annexure T

Page 70 of 78
 Annexure – U
(See clause 35 of Section 3 -GCC )

Physical Completion Certificate

Name of Work:
……………………………………………….…………………………………………………………………………………
………………………….……………………………………………….……………………………………………….………
………………………………………………………………………….………………………………………………………..

Agreement No. ……………………..……………..…………. Date …………………..……………..

Amount of Contract Rs ……………………………………….…….

Name of Agency : ……………………………………………………………………………….…

Used MB No. ------------------------------------

Last measurement recorded

a. Page No. & MB No. ________________________________
b. Date _______________________________________________

Certified that the above mentioned work was physically completed on ……………….
(date) and taken over on ……………….. (date) and that I have satisfied myself to best of
my ability that the work has been done properly.

Date of issue

Executive Engineer
….....................................
……………………………..

Section 3 – Annexure U

Page 71 of 78
 Annexure – V
(See clause 35 of Section 3 -GCC )

Final Completion Certificate

Name of Work:
……………………………………………….…………………………………………………………………………………
………………………….……………………………………………….……………………………………………….………
………………………………………………………………………….………………………………………………………..

Agreement no. ………………………………………….………. Date ……………………………………

Name of Agency : ………………………………………………………………………………………………

Used MB No. ----------------------------------------

Last measurement recorded

a. Page No. & MB No. ________________________________
b. Date _______________________________________________

Certified that the above mentioned work was physically completed on ……………….
(date) and taken over on ……………….. (date).
Agreemented amount Rs. …………………..
Final Amount paid to contractor Rs. ----------------------

Incumbency of officers for the work

I have satisfied myself to best of my ability that the work has been done properly.

Date of issue

Executive Engineer
….....................................
……………………………..

Section 3 – Annexure V

Page 72 of 78
 Annexure – W
(See clause 39 of Section 3 -GCC )

Salient Features of Some Major Labour Laws Applicable

a) Workmen Compensation Act 1923: - The Act provides for compensation in case of
injury by accident arising out of and during the course of employment.

b) Payment of Gratuity Act 1972: - Gratuity is payable to an employee under the Act
on satisfaction of certain conditions on separation if an employee has completed
the prescribed minimum years (say, five years) of service or more or on death the
rate of prescribed minimum days’(say, 15 days) wages for every completed year of
service. The Act is applicable to all establishments employing the prescribed
minimum number (say, 10) or more employees.

c) Employees P.F. and Miscellaneous Provision Act 1952: The Act Provides for
monthly contributions by the Employer plus workers at the rate prescribed (say,
10% or 8.33%). The benefits payable under the Act are:
i. Pension or family pension on retirement or death as the case may be.
ii. Deposit linked insurance on the death in harness of the worker.
iii. Payment of P.F. accumulation on retirement/death etc.

d) Maternity Benefit Act 1951: - The Act provides for leave and some other benefits
to women employees in case of confinement or miscarriage etc.

e) Contract Labour (Regulation & Abolition) Act 1970: - The Act provides for certain
welfare measures to be provided by the Contractor to contract labour and in case
the Contractor fails to provide, the same are required to be provided, by the
Principal Employer by Law. The principal Employer is required to take Certificate of
Registration and the Contractor is required to take license from the designated
Officer. The Act is applicable to the establishments or Contractor of Principal
Employer if they employ prescribed minimum (say 20) or more contract labour.

f) Minimum Wages Act 1948: - The Employer is to pay not less than the Minimum
Wages fixed by appropriate Government as per provisions of the Act if the
employment is a scheduled employment. Construction of buildings, roads, runways
is scheduled employment.

g) Payment of Wages Act 1936: - It lays down as to by what date the wages are to be
paid, when it will be paid and what deductions can be made from the wages of the
workers.

h) Equal Remuneration Act 1979: - The Act provides for payment of equal wages for work
of equal nature to male and female workers and for not making discrimination against
female employees in the matters of transfers, training and promotions etc.

Section 3 – Annexure W

Page 73 of 78
i) Payment of Bonus Act 1965: - The Act is applicable to all establishments employing
prescribed minimum (say, 20) or more workmen. The Act provides for payments of
annual bonus within the prescribed range of percentage of wages to employees
drawing up to the prescribed amount of wages, calculated in the prescribed
manner. The Act does not apply to certain establishments. The newly set-up
establishments are exempted for five years in certain circumstances. States may
have different number of employment size.

j) Industrial Disputes Act 1947: - The Act lays down the machinery and procedure for
resolution of industrial disputes, in what situations a strike or lock-out becomes
illegal and what are the requirements for laying off or retrenching the employees
or closing down the establishment.

k) Industrial Employment (Standing Orders) Act 1946: - It is applicable to all

establishments employing prescribed minimum (say, 100, or 50). The Act provides
for laying down rules governing the conditions of employment by the Employer on
matters provided in the Act and gets these certified by the designated Authority.

l) Trade Unions Act 1926: - The Act lays down the procedure for registration of trade
unions of workmen and Employers. The Trade Unions registered under the Act
have been given certain immunities from civil and criminal liabilities.

m) Child Labour (Prohibition & Regulation) Act 1986: - The Act prohibits employment of
children below 14 years of age in certain occupations and processes and provides for
regulations of employment of children in all other occupations and processes.
Employment of child labour is prohibited in building and construction industry.

n) Inter-State Migrant Workmen’s (Regulation of Employment & Conditions of

Service) Act 1979: - The Act is applicable to an establishment which employs
prescribed minimum (say, five) or more inter-state migrant workmen through an
intermediary (who has recruited workmen in one state for employment in the
establishment situated in another state). The Inter-State migrant workmen, in an
establishment to which this Act becomes applicable, are required to be provided
certain facilities such as Housing, Medical-Aid, Travelling expenses from home up
to the establishment and back etc.

Section 3 – Annexure W

Page 74 of 78
o) The Building and Other Construction workers (Regulation of Employment and
Conditions of Service) Act 1996 and the Cess Act of 1996: - All the establishments
who carry on any building or other construction work and employs the prescribed
minimum (say, 10) or more workers are covered under this Act. All such
establishments are required to pay cess at the rate not exceeding 2% of the cost of
construction as may be modified by the Government. The Employer of the
establishment is required to provide safety measures at the building or
construction work and other welfare measures, such as canteens, first-aid facilities,
ambulance, housing accommodations for workers near the work place etc. The
Employer to whom the Act applies has to obtain a registration certificate from the
Registering Officer appointed by the Government.

p) Factories Act 1948: - The Act lays down the procedure for approval of plans before
setting up a factory, health and safety provisions, welfare provisions, working
hours, annual earned leave and rendering information regarding accidents or
dangerous occurrences to designated authorities. It is applicable to premises
employing the prescribed minimum (say, 10) persons or more with aid of power or
another prescribed minimum (say, 20) or more persons without the aid of power
engaged in manufacturing process.

Section 3 – Annexure W

Page 75 of 78
 SECTION 3
Conditions of Contract
Part – II Special Conditions of Contract [SCC]

Section 3 –Part -II Special Condition of Contract (SCC)

Page 76 of 78
 SECTION 4
BILL OF QUANTITIES (BOQ)
General Description of work:………………………………………………………………………………………………
…………………………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………………………
Probable Amount of Contract:
(Rs. In Figure) -------------------------------------------------------------------------------------------------
(Rs. In Words) -------------------------------------------------------------------------------------------------
S. Particulars of Item of Quantity Unit Rate Amount Amount Remarks
No. Work (in figure) (in words)
I II III IV V VI VII VIII
1.
2.

3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Total Amount (Rs. In Figure)

Total Amount (Rs. In Words) ____________________________________________

Executive Engineer
….....................................
……………………………..

Section 4 – Bill of Quantities (BOQ)

Page 77 of 78
 SECTION 5
AGREEMENT FORM
AGREEMENT
This agreement, made on the _________________ day of ________________
between ___________________ (name and address of Employer) (hereinafter called " the
Employer) and____________________________________ (name and address of contractor)
hereinafter called "the Contractor" of the other part.
Whereas the Employer is desirous that the Contractor execute
________________________________________________________________ (name and
identification number of Contract) (hereinafter called "the Works") and the Employer has accepted
the Bid by the Contractor for the execution and completion of such Works and the remedying of
any defects therein, at a cost of Rs._________
______________________________________________________________
NOW THIS AGREEMENT WITNESSED as follows:
1. In this Agreement, words and expression shall have the same meanings as are respectively
assigned to them in the conditions of contract hereinafter referred to and they shall be
deemed to form and be read and construed as part of this Agreement.
2. In consideration of the payments to be made by the Employer to the Contractor as
hereinafter mentioned, the Contractor hereby covenants with the Employer to execute and
complete the Works and remedy any defects therein in conformity in all aspects with the
provisions of the contract.
3. The Employer hereby covenants to pay the Contractor in consideration of the execution
and completion of the Works and the remedying the defects wherein Contract Price or
such other sum as may become payable under the provisions of the Contract at the times
and in the manner prescribed by the Contract.
4. The following documents shall be deemed to form and be ready and construed as part of
this Agreement viz.
i. Letter of Acceptance
ii. Contractor's Bid
iii. Condition of Contract: General and Special
iv. Contract Data
v. Bid Data
vi. Drawings
vii. Bill of Quantities and
viii. Any other documents listed in the Contract Data as forming part of the Contract.
In witnessed whereof the parties there to have caused this Agreement to be executed the
day and year first before written.
The Common Seal of ____________________________________________ was hereunto
affixed in the presence of:
Signed, Sealed and Delivered by the said ____________________________
_________________________________________________________________ in the presence of:

Binding Signature of Employer _________________________________________

Binding Signature of Contractor _________________________________________

Section 5 – Agreement Form

Page 78 of 78
 orutf,q rgs sTfu{idr
Tffiq qiBr+t tqr, qEqrtqr
"fr" ftfrl, trftq ng, ftfeq1q6 rrqq, .iTqrd
[email protected] I 0755 -2551398

3133 / zz /fr-10lqTqid / zozs fiqd, fuqio 03 / os / zozz

1.

ftqq: aio. trrr fuilT gmr qffi Fifuil qq{ \r+futr z.ro ii risiltn erao (d+a
srrft-q( qrf d ftd) t

€-nf orqim$-q qd fr. zsaz/zz/ft-to/arqft/zs, fiwa, fu{io 28.04.2023

frru{rn wfif,{q qft fuql qrat B,-
e-Effid qa fr

1. @]*{e srfl€fu d F{g m. rc o) Fqr5_qn qil qd :-

Contract Data
GCC Particulars Data
Clause
18 Defect liability period and 60 Months after physical completion
maintenance of work

2. oFot go.t o1 ffi gfu

"No security deposit/ retention shall be retained
from the payments for routine maintenance of the works" @i ffifuf, fuql
qff,r t I

3. .b-R-.b-l 30.2 ii The security deposit may be replaced by equivalent amount of bank
guarantee (duly verified) or fixed deposit receipt from Scheduled Commercial Bank
assigned to the Employer (duly verified), with validity up to 3 (three) months beyond
the completion of Defect Liability Period/ extended Defect Liability Period. t|.6t
qdr
4. dR-6r 30.3 o) fr=dfud fo-qr qror t t

5. o.R-or rF.. 30.6 of fr-s srdr €ftd qrt tqd q s-dfuf, sq

"2.5oh of contract
amount" d "Z.SV" of contract amount at the time of agreement" qa,f qfd t

Security Deposit retained ll2 after physical completion of the work

from the bills to be of second year after physical
114^ after end
refunded to the contractor completion of work (after inspection of
maintenance)

C:\Users\ACER\Domloads\Gen Letter 2022 (3) doox

 (c) Il4ft after end of third year after physical
completion of work (after inspection of
maintenance)

sffi riqilqq q-r srrftq-d sso- o-rqT d fuS t I qft qr ftfuEr utr;{ o-r
trwr€'nr
lpL)
rgs 3Tfu{iilr
qrftq qiBrot tcxr,
frqrg (q.s.)
g.m-+io
qfrftIfr:-
3l3q /zz/fr-10lil-qit /zozs dqrn, R-qi6 bS /os/zozs

t. fto sarqo, qmftq -i* fr, f+c frrnq

2. ft-q Hfuq, qm+q qffi, riqrtra gq qffiq tfo-rs fuilT
r

3. qErdsro-n, qwtreq -ilfuw t

4. 3ilN gq qfuq, q.q. errsq, riqrrd gq qFft"T fuo-rs frqq76-* engm,

q.q. I

s. 3Tq{ 5Uq {{fuq, q.q. qrNrq, fuf, f,flilT I

6. qFdq, rT.q. qlrsq, qqrTf, W qffiq fdfi-rs fuqFr I

7. qfuq, q.q. qTfsq, fu

ffiTr fu,nq f

8. 3Tl-{ffi, {luIF[ {{qFI {{+IRT. q.q. I

s. TTs GTFriaT, ci6 ffiur

ft+Tf.r/cif, wn€a qiM fuqn/q-d i{{ilEr;t
f4qm7u.u rrfrur ss6 fuorfl qrFowr I

10. GTfier"I ri*, il-frq qlfu+t +fl, qusET qE-dg{ qft fr{ srrq-d qd fr. 565
fufi-o. 03.05.2023 d ti{,f tt rA++ref gq Gr€{fi-- o-ffi ig nFo I

rr. od{-{, fudr qrfkT, q.q. I

12.9G[ ol-Sq-d-{ Grffi, fudT riqr+a vrrfsT, q.q. I

of Gtr{ qaqT.f ifuo r

qffi'r qttrfrt trfl,

,Tlqrf, (q.q.)

C:\Users\ACER\Domloads\Gen Let(er 2022 6\ docx

 orqff,q rgs sTfuddr
ilfrq qiBrfr1 +{r, qsqtra-qr
"fr" frT, ffiq aa, futqrqa .ltrq, $ilq|-d
[email protected] I 0755 - 2551i98

mqin e?69 / zz /fr-10 /qfqifr / zozs q\qw, kq@ Lg / qq / zozs

qfr

d6 ffiq arr wfr frfuET qq-t q+fu-tr z.ro ii riYiq{ qcro I

orqffiq q-{ m. arc/zz/fr-to/wqtd/ zotg, qtq-.{, furlo. oo.o2.2o1s

sqRt-fi qqtrd qa d qTs?H t do MrT ftrrnr 6r urt ftfuo qq-a

vfRtrcr z.ro ii G{tcrrrrfi qqiltrq F{i gq ilftoT ilffi ql-dr gr*t d-ffi-i{e gt{l
GrTriBd d qfi qrft s 2.oo dfcr € Grfuo of fthEleil & ftfrET qq-{ giifVErq 2.ro
qft fuqT rrirT QIT I

ilqrr qtffi tqr arr slqQEir q-'f d ft\ wt o1 qd q-ft fr-fuET3ri

-Fq gm frfuqT qqt q'iBffi z.to of o-R-or 29. Performance Security \q 30. Securitl'
Deposit f,erl Bid Data Sheet d Cluur. Reference 22 t ftqqrtR qeisr-'T lbq ulct t\,-
30. Security Deposit
30.1 The Employer shall retain security deposit of five percent and Performance Security'
of two and a half percent of the amount from each payment due to the Contractor until
completion of the whole of the construction Work. No security deposit/retention shall
be retained from the payments for Routine Maintenance of rvorks. ln case, thc
Contractor furnishes bank guarantee for the amount equal to Performance Security, of
two and half percent retained from each payment due to the Contractor. the samc
amount shall be repaid to the Contractor subject to condition that the validiti ol'bank
guarantee is as per provision of Clause 30.2 of GCC.
30.2 The security deposit may be replaced by equivalent amount of bank guarantee or flxed
deposit receipt assigned to the Employer, with validity up to 3 (three) months beyond
the completion of Defect Liability Period/ extended Defect Liability Period.
30.3 The Security Deposit shall be refunded on completion of Defect Liability Period.
30.4 On the salisfactory completion of the whole of the construction work, hall'the total
arnount retained as security deposit is repaid to the Contractor. one-fourth of the total
amount retained as security deposit is repaid to the Contractor at the end of 2nu year
after completion of the constluction work and balance of the amoLlnt retained as
security deposit is repaid to the Contractor at the end of 3'd year after completion o1'
the construction work subject to condition that the Engineer has certified that all
defects notified by the Ilngineer to the Contlactor before thc end of period prcscribccl
for repayment have been corrected'
30.5 The additional Performance Security for unbalanced bids as detailed in Clause 29 of
the Conditions of Contract is lepaid to the Contractor when the construction work is
complete.
30.6 The Performance Security equal to five percent of the Contract Price as detailed in
Clause 29 of Conditions of Contract is repaid to the Contractor when the period of
five years fixed for Routine Maintenance is over and the Engineer has certified that
the Contractor has satisfactorily carried out the Routine Maintenance of the works.

If the Routine Maintenance part of the contract is not carried out by the Contractor as
per this Contract, action under Clause 18 and 27 will be taken, and the Employer will be free
to get the routine Maintenance work carried out lrom another source and the amount required
for this work will be recovered from the amount of Performance Security available with tlie
Employer andlor from any amounts of the Contractor whatever is due along with additional
20Yo amotnt as penalty.

Bid Data Sheet

Clause Particulars Data
Reference
22 Amount of Performance Security 2.5Yo of contract amount

qftq q srrft{-d q.f d fuq wfr q,t qd qrft fth-Ercil fu sm

srr:
rtrra dq 6}q-r | 0q o-rd @1 fthEleii d ftd Td q q<ft q-{ sl-{t qffi frfuET
qqr fr 6p1vtsn t

g.mq1- &?f\/ 22 /fu-to /awrfi / zozz

qfrfrfi:-
l. fro saqo, qmfi=q q* fr, fud fu+rFl I

2. fuq qh--q, qmfi=q riffi, qqq-a gq qffirr fufiT-fl fuqm t

3. q-6rdqro-[i qtqqerT -dtfuw,

4. 3Tq{ 5Cq q-Fdq, q.s. slmfi, qqr+a \ti fr--41-s fr'-l.T/fumT-s 3n$KI'
q.q. I

s. 3Tq{ 5C"q HFdq, q.q. s[flq, ft-d frqFl I

6. qFdq. q.q. g[l-sq, qzTlqa Tq ql-ntr fuo-rfl fu+ilrl-l

1, qna, s.q. slNFT, e)_o Flqtul fu+il-{ |

8. 3ilgK, {rs{q €qTrI qrrKl, q.q.

qIM
I

s. rg* GTft{idr, d}o Fqfur frailrT/do Rr{ea fuilT /qd H{ITtf'l

6*n-17t.u. qrftut Esfr' fufiT-fl qrffi-iq t

t0. gq efi=rrf,r, qrftur qlffi +qT, ffiq olqfd-q, .nqF, E-qti gq qqdgq, q.q I

ll. fuf,r srfRT, q.q.

@-fr{d{, I

12.5cq @-rsq[-d-{ 3lffi, fuf,r qq|{d srrtrI, q.q. I

of Giq qqlTef iR-o t

E \nr^-^;\n-- I -f.-' l^aa i^^'

 fir{qrilf, {fi
EFrqtfrq,
qrfrur qiFdt tqr,
SEtr Timar fdk
zoz, ffie rEa, o*+dte qftTt,
Email:[email protected]
iqtr
,dJ. Ph:- q73t-2364452
m. \A'r )tlorzBf+a rur,qr.fi.
r zozs
?"qr{, fq-dr6' zt/o2/Zo2s
02 2
aqqhr b u-qqrd ffI 3rlr t ilrmur qiff6l
tU fi;fi-+5d S-dcffq-d e{rtren 3ia-d-d Rfufr Ehrt C. qtr{d
€_qr gHrrr
Fqt * fuf6d Batur o'rqf
qitl.8r €-fl ARr der)fud qq{ fu t d} Rsrwr q-6fr qrfiur t
lttB"E z.ro 3l-{sR rca+ dsntr{, EqiR-d frA (Key Date)
armur qifd'6l*qI Cnr art qs.:r).sm. fraio u.oc.zozz $ sqrEen-fr 3r{€R dqr
3rffifr (Effdr tr-gfr arft
ili 6I frai6 ilfi:dlnfud) lzi f+gil-flur 614 E Fi-6 fufq fufirrr fi<tfraio.e1.e1.2e2a
Efu-a rq fi *{-d mrd dt JIA drid Afuqr $rili-d *'nnm qr
6r drfi tt $riFd Ef+qr erra + mfu
www.m Ita de r! n w M ar so-S
t E-a-+,r fu{rlT Bang+n t,-
Bfr{r
fuEF tssr E-6rw 3IAITd Fffqr miII-
aF.
mr{ ar are ar4iI
tr{ qD-g
(PAc)
rtFr r$I .6I cfr 3na;M
ira Rrftr i F++rd 61 6-e
t5.
,) F t ttt rk)
1
3
*) ..i)
4 5 6 7
l. 2025_RES_ $i4a-qrer srdra Fdq a$ gn-drfr 8 9

405131 fuq-Er fat

qrfrsr oz kf,r
.dt F-dtt 9.27 18540 2000 6 sr6 9elq

2 2025_RES_
ffi rr+a B-alur gra-fia rra
qqr+d 3rrtFr< gg-{
405132 $-<t{ ,Jr$ur a<'h' 9.27 18540 2000 6 frr6 ceFr
or Bm p<tr
si4a-q6 r+a ffior q't{r +r-dtfr
3 2025_RES_
s-a&srurrff dsrq-d rsesr $At{
/t05133
rlr$sr oz ft-dr FdtT
tdt{ 9.27 18540 2000 616 cqq

2025_RES_
3ii4a-{r$ r+a Erqtor ii6r +o,
4
405135
trqrfl ara d"rq-d i?tsmr Fit{ r;d{ 9.27 18540 2000 6 416 csrq
Trfrur oz Bdr 5-<t{
Ji4a-qr$ gr+a ffiq Era ffr
2025_RES_
5
t105136 t-€t Ei.F rrra tiqr+a Ei+, 5atr 5dl{ 9.27 18540 2000 6 7116 C9FI
qrfrsr oz E-dr
f<t{
6. 2025_RES_ JrirraETSI rca F-atsr aiqft-ql m..
405137 oz, sitr Bm Fqt{ sit{ 9.27 18540 2000 6 416 CEFI

7. 2025_RES_ :+iera-q6 r+a fuur Edftqrqta

tlos138 m. or, sitr Bfrr I<t{ €ia-{ 9.27 18540 2000 6 416 9'2III

8 202s_RES_ 3rirrqr$ r+a F-ai"r fd5{r, sit{

t105139
B-dr Fdt{ sar 9.27 18540 2000 6 Ji16 cP{q

9. 2025_RES_ r+a fuvr

s{irra-qrgt arcr+{r, sit{
405140 Bdr $Ak €it{ 9.27 18540 2000 616 gefi
 r0. 2025_RES_ siiaa-qrS q?rd F-atq ilq-ard$,
405141 siti Bdr 5-<t{ €it{ 9.27 18540 2000 6 dr6 IIEFI

ll 2025_RES_ 3frrfir$ r+a Falur Enta m. or,

405L42 sit{ Bdr $Ak €'it{ 9.27 18540 2000 6 416 carq
12. 2025_RE5_ siqrqr$ r+a E-aiur o-drft-qr,
It05143 Tit{ Bdr fdi'{ si+{ 9.27 18540 2000 6 {16 ceIII
r 3. 2025_RES_ $iqa-4r$ r+a fu,"r Erdftqr, flit{ qia-{
405744 Bdr il<t{ 9.?7 18540 2000 6 {16 cem
14. 2025_RES_ 3{iardq6 r+a Mq ftrdtqr,
it05145 sit{fudr dt{ €itr 9.27 18540 2000 6 416 cqq
t5. 2025_RES_ 3rimrqr& r+a ffiq ro.trwia,
405145 sift B-m 5-<t{ {it{ 9.27 18540 2000 6 Jn6 CEIT

15. 2025_RES_ r+a E-aiur qratq siildr,

3{iaa-qrfr
N5L47 sit{ B-dr a<t{ €it{ 9.27 18540 2000 6 A16 csFI
17 2025_RES_ Sira-qrS srtEr ffiq .Frcmrr
405148 Hit{ E-dr S-{t{ HiAT 9.27 18540 2000 5 ,n6 celll
18. 2025_RES_ 3{iq-d-dT'S rqd Mor orsr, ritr
ro5150 sia-{ 9.27 18540
B-dr Fd{ 2000 6 frr6 9EFI

r9. 2025_RES_ sririlEr& r+a fuq rrola m. oi

t105151
sifi CaT ffi €itr 9.27 18540 2000 6 416 CEFI

20. 2025_RES_ sia-{dT-e r+a Aat"r nqlo m. oa

405152 flitr B-dr Fdk Hia{ 9.27 18540 2000 6 frr6 qem

21. 2025_RES_ 3{irrd-qdr rca E-atur 3l-t- ilt}qr;

rrc5153 sit{ Bdr gak €itr 9.27 18540 2000 6 qr6 ceH
22. 2025_RES_ srirrd-qr€f sFEr Mq Mqr
405154 orqer, sitr B-dr gatr sid-r 9.27 18540 2000 6 JI|F ceFI

23. 2025_RES_ gir+qre qtt;r ftEtur qeBqT

tlos155 cora, sitr Bdr -dlr ffitr 9.27 18540 2000 6 {16 qeIII
girrdEr$ r+a ffisr csrar.
24. 202s_RES_ sitr
405156 Bdr f<tr si+{ 9.27 18540 2000 6 416 cerq

25. 202s_RES_ siq-a-qre r+a fraiq ilffi$ ilrt{-

t105157 r, uitr g6y 61* sia-{ 9.27 18540 2000 616 ceFt

26 2025_RES_ 3rimrure r+a Mur gtr<g*r, ritr

rl05t58 B-dT f<t{ €tt{ 9.27 18540 2000 6 ;n6 cellr
27. 2025_RES_ $irta-qd r+a B-siur {o-c-dr
S+d,
trc5$9 qit{ B-dr $At{ sia-{ 9.27 18540 2000 6 416 ceIII

?8. 2025_RES_ 3riqa-qrfi r+a ffiur 3iarlrflI iF.

405160 or, sitr Bfrr Fqt{ siti 9.27 18540 2000 6 {16 cefi
29 2025_RES_ $izr+qre r+a ffiq crqrs& m
tt05151 or, uitr B-ar 5<tr €it{ 9.27 1.8540 2000 6 416 cellr

30. 2025_RES_ sia-.rqr$ r+a M'q ddfu<r,

qia-{
tt05152 sit{ Bdr fik 9.27 18540 2000 6 frr6 ceIII
 I 3?.
2025_RE5_
rl()5163

2025 RES
405LU
$irla_qr$ er+{ Batsr
,a-( Trmsr or Bm 5dtr
frqer 4-ftr{

3{irErdre rE;T A-aiur r{t{I 6.. ol,

rr( ,rrmq or Bdr {<t{
3{i?Er4lfi 9]-d;I Baisl fo4-g6T a,
a-(

a-(
9.27

9.27
18540

18540
2000

2000
6

6
A16

416
CEFI

qEFI

33 2025_RES_
/o5165 a.( qr$q Ol Bd{r f<t{
4-( 9.27 18540 2000 6 A16 CSFI

34 2025_RES_ Jiqarqr* qe.d B-aiur 6dt(I atEdr

t105166 6-4rs ts, a-( rlrmur or For gatt a-( 9.27 18540 2000 6 A16 IIgI5

35. 2025_RES_ 3ri4aara eftra F-d.q ada amrq,

405167 Bdr.Af{
,Irfrsr or 4-( 9.27 18540 2000 6 JI16 csFr
ririlqr$ mrd F-diur atqaT{r,
2025_RE5_
36. qrs dqI{d iisrt 4-( mfrq ol e-E 9.27
405168 18540 2000 6 416 CEFI
Bdr i<t{
3{irra_ql& sEra F-atsr r{fucr F}fir,
37 2025_RE5_
,Jrfr dql{d s-afr'+r 16 arfrq or f(
405159 9.27 18540 2000 616 carq
E-dr Fdf{
38. 2025_RES_ 3{ira-dTgt ,*ra H-aiur tu-cd, a(
405L70 qrfrq ol fudr s;dk F6 9.27 18540 2000 6 A16 ceFI

39. 2025_RES_ Jiqa-iTS sEra fuq ot(ftqr 02,

4-(
40517t

202s_RES_
4-( ,Irtrur 02 B-dr f;qt{
gier+qre fl'.ra F-dtqr it{-dtfl ,rrff
9.27 18540 2000 6 {16
l*"
40
trcs173
dvr+6 q56on, a-( ,Jrfrur 02 a-( 9.27 18540 2000 6 frr6 gerq
Bdr $-<t{
3ri?ra-ql& r+a E-at"r {rrrdrqrm
41. 2025_RES_
qrfr dqr+d aFF:u6nE, rq arfrur oz EB
445L74 9.27 18540 2000 6 7116 ceH
Bdr F<t{
:iizr+qr€f r+a B-aiq otcr 6i6fuqr
42. 202s_RES_
rrrfr dqr{d 6i6,ft-cl a.( qrfrur oz a-(
405L76 9.27 18540 2000 6 416 cqq
ft-dr F<t{
3dra-qr€t mra fusr grfrgu ara
43. 2025_RES_
dqrqa rqrq. a-( ,Jrmsr ot fraT a-( 9.27 18540 2000 6 ar6 geIII
405177
Fd{
gizr+qr€I r+a B-atq cnFEr qtrfi
44 2025_RES_
riqrq-d 4r{&, a-( ,Jrmq or Bar 4-( 9.27 18540 2000 6 416 gEFI
4o/5L78
v-<t{
sr{qrfuo rca fuor afr 3il5ar
2025_RES_
45. F6rfrsn E6 at. 5r, lrl3 q;qelrrTl ildT 4. O5 8r00 2000 4 A16 kdq
405180
EFfr f<t{ Bfr)
(Eqrq-o'
qB?rfrfr +-f,rs s-q (3rfrfrfr 6fi)
45. 2025_RES
405181
Mur qnsfrq anzft-o qa €itr 't3.42 2 5E40 2000 6 A16 ft-dq
qqn
qt{'- ({rRr drq f) 425.35
F
 r- BftSI d.irf Rfuil {Kevpatesl}
r. f
eerqR q-fr q-6Rra 6rkdi6. to/o3/2ozs
2. Afuqr qtr{ 6-q 6.-ri or qFtsr
Fai6, rc/$/zozs Efi{r to;3o .r$
3. Ffuqr (t trqd +-ri or qrfrT
kaio' rc/o3/2o2s q_rrq ro:30 rS
4. Afuqr q-t q'q-d 6ri 61 3ifrfl
Eai+, zl/o3/zo?s sfiq t8:oo iri
s Bfufi il+AifiI fus ga-+ +r kaio zs/o3/zozs Efiq t2:3o rd
6. Efu{r futrq 3nw,nqd6r f{s g-f} }.qasrf, o,r4qrffT ?ifi rlrmq qiltrfl
t_qr isnq
f<t{ grrr Bqtkd frf,i+ +,t rffi ar&tr
2- frfa qr 3fra drtd fus r4r ori src a{rf,ts qre ffi ili (rtn}cil:_ 3rM
frEr$r-A
(l) frfud fttr{d trrrrq rrr qr ri;ftra nfifrs{q fiI {S{ 3Tqfrs qrrdr:rfrorS
(2) eFrsr rr{ TrR} 5q} roo/-6r ts qa +- 6{ 3rrf,t5 -rar grfu fg

* fui Ero-Ero errer-q{ M tr trq ffit rqi+m 614

)(ennexure-a)
(3) 3IIa drF ilrrr 3rflEn rlfq} or{qrfid ?iil,{Efiur qiff6; t-qr 113nr pqk fi qET C.tq 6}1 3tis
ffi rama rtRr l6rfi qftRfi d ara +fi 6r ar&t
(4) +d enrg fi qF tti 3rra.6-{ g6-dr rarut qr 3rqf,Is oral sM
tt
r

(s) fr.us.E. d*{d q-,rrq q* srqdts orar nffi tr

(6) s@a war 6fs 6I qfr 3rrdts orar erM tr
frrrq,-c
afufi*n anr Efua .*;il F6 3i-d dd-d Frffrd soe.xrsformat f €r rqa 6rfr Fbftr
3- Hffqrqrr t'q ri,-
r. Efua qqr 2.1o.Fr dro q-dr fr r*qqa or iir ers Bfu<ror$ +i grsrc fr oTA fo.
t t 3ifrfl E_drs
6I q-trfrr a of aqr 3{Tfr fug cffiafts u-qa ott aqstfe d ffi q-6R trr JgEqr 6
fun fusn4
rdrfis a-€t tr ro-6 sfi Ar+46R h qr6e q{ Er+o u-qa 6.i fi Ffu f
sk T€t a qrtfrr
z Efuqron gr$-s{ifr r.F mr{ B ;ft-lt+,qa or :r+ato-a or *tr *_tqqr f sqrtrd
ncfi 6r{ 6-{ar
3{ffi tr qimffi q.i grfa 6r 3'{*6-d orqtoq,sr{qra-a ?ifr {raq qifrft n-4r ri{r4 fitr * s6.e
tl
s. Btffl qq-r ffic https://www.motenders.sov.inw ffi sJrrdra 6T ftg{ srqJfel Fq lEi
ilqr Ffiqr dr q?F'-dr tl
4. qAo, Afu<r b srq AfuqroR tnf 3iadFd fus ilffr 6-G q-rq Ef{Er fr eiBor_z d dfud (6r}s
gtr.rqr6 sq t 3rq6tE orar srfu t r

s. F-qtET fi{ ,iiirfi sra fu+rorzur+orfr orqtilq, 6r4qrd-d ri*, ,rrfrur citrdl t-sr {rr,r $<t{ *
ordnr$-a rrq f i@ dr s-6-S t I
s. EfocrdFrt s) dla-6 ftdr+-fr) Fq t Eht$ $ (Rrtr 6r+aq d aqr n6t ori tr T-rs rmra-o
3iErdrtr .pdf rrr .rar (srt 3r{FK) €t rqa ori tr
z. Ef+cr+'r fi am snrerfa 3rq-dls f6't zrt sre (Frtr (Ffuqr rd * rEvnl (Frnq s€t qri ad
qr a ffirq 3frw ffi orqt*q, or{qrfid ?in, zrrsq qitrfr t-{r, drm F<t{ zoz ttdrfs a.ra
$dt{ f Btrttud Eaio q}d sritr
 e. Efo<lrER Aff<r qfr€qt * snrr d-A fi $ ordqrd-d ?ii, {rfrur qifi_fir
$_qr {ir{rrr g-<t{ * +iu-6 6-1
6r{ n*rd 61 6r+ q-6R * aftTUr ,,rqeo-6'Fq t +r *i ilfi faiur 614 f 5qmrr 6ra Erfr fuur
{r,-rtr fir 5rrildrdr/qft-drFa fi dciq d eft rfr-eiT"fr r+do-a
g. Ffa-qrorr o,l rga-*r n ol *n d Ef+cm,-. h h_i *qqoq ilmr
soo rFT ErFr Fq{r{sr 6r+fq * {r iFir
ro. qot EfOar e-Frq 3@rykdt6 :. lti q-r-c nffia, 61a1
ft $Zx.tr #o mt ort+ ,
1r. ..r*nr nfrr ($rd.nF) 6r{q*d ii*, z,rsq qirra
*+ rifirrr. sdh *. qw f tq 6tfr irq, fos ilfi
o,{i h Edio' t t+ a5 fi srqfr a-o dq Ftdr qGq r
rz. Efa-qronzo-$ Enr q-do, 6r{ fi fun gq-6_Bro
Afrql fua trqd 6-rfi Ftrfil
rs. qt 6it &-qrr qdF'fr trFIfi m-d f qr&+r irrrqr
*c,Fdl1 d d ffi E_d Ero (r-6.& 614 h h_E
31il4-
3ffir Bfco u-qa a€l.6r artir raen q.d rm q-qd AfrEr{ f{F
ot A srtti
ra. FfusrdFrr fo'ifr efi fusrq fr *+, fr€s r€t qrtrtr qE
d_dr tsr qrqr qrar t d, d_.ifua
Efa-qr+nz&-Cr 6r Hfu<rzraev {rarr 6.r lAqr ara-rn
f

rs. ra +ifta <-e il. srd?td .ftfod a-qt drrr$-{

d-dr orF}r e_o frsn4 EEr Bqifr_d Tt w ro_qt or
{rrfla fiE=qr irar 3rffi 6lmt E-q;-q 6r Fft f *-dr{ F"i 5Rqrfr
dnrl
16. or{ 6-{i fi Etna ffi cfi ,iA-+' St or
de-dr ra-rqrfua d<ifu6 36qR 6r dfqT,
rz. ft*q et{ fufirg urfu+-p17aa67 ontr d m1 Fzrd qrfra
t. 6r ya-rqrtrE &.arr or ftrnr
u. ar$.fr.ur$.S3r6. frfr|s +o, fi frfud (tnstrument) ara n€t fu qrtir
1e' e.*;s6q o.i arqfrfue * sq f urra fr+ar5vr-r s qfrqrf, Eu'€
arqfufua h. sq * 3Biq + {4
fo* 6 ogUormffiFf+e do, * aql (,s.*.3rR. ;n or{qrfrd ri*, zrrfrq Jqr $fir,I f_<tr fi
qqr * iq r),rg<-;rr fi.rrq ,rar o.rfr Ftfit "fi6,
20. gFe, FIg :ik arao s{ra zierorq EI{r q-trf-d q-* 6) qrF.fr.3rR a?i :r+ gmt qrE f arq afi dr
e_.
,T, Ptu"
6 kq zC rcdtud ftflrts 3rq-mE a-€t +ri qr +iqtud *{o e* **" *.o
or fr ar&tr "qo
zr' Et+a {ff-d *''fa a sr{rt-a o-d or wt nfuon sn-a JrR*rt b vrs g{B-a
Gmr or4 d. loo at
q-6R 6r AFiE ili rn $q-fl ffiA sfi qftRffi
* {.a gfG tq r& rhftl
zz. Bfua s{;F fi (16'sar6 fr Ffosror 6i gr{tiE orar
fbn:rsqr Ff+a ffi e-a, FffrE arfi
ar&fir sqil 3rffi 6l J{fuo.R Ftrn 1o, d.ifud Ffuqrorr fir (,s..tBrr rrssra or,or{
gr+iaq
fi ga, Bfoa
ott
zs. Hfuff+R 6Kr sr*iq +-ri *
qqra ls Efs fi efrd{ 6,14 Hir{ T€t fuqr srm
t,d r*{.-d Bfoqr sa,
fr{R F} *ffi
ilr ftra $ffi
+t sfu6'r o).n fu ara-qmn dRT E.,rr rftl ('s.€HE ire[ qrwrcf*
fudfta fi rtfcI {rqsrd +-{ ga, Afuqr 3nd"ur fi offir 6r orizfrr
z+. f
Hfuqrmr 6t Hfudr rdfu'd or{ fr g-arEqra-o sq q-rrtr -e g} t Mq
6r{ Ffqrqe d qot
o-rar gM dlrnt
zs. frat"r 6rd f a-fqr Tfi 6'r sts to-s 3rerEr fia6 gwrdr 6r l-a +r €r so-q o.rar sBar{ Ftrrrr
26. raq5'i{6, h errrila *'wq oF-s ,itur {qqr or :rarqft trrrTol rEr trqd 6.(ar
dm gEqqr fr{qr{{R
ra+o' t{o' t iqqt4 6I ,rg srral or rrrrofr 6-itil 16-qI ar}rn1 q14 f u-ga 5H Erfr {rfJi qir
sqql,r ri?fud ffi tE (S g'{sr nq}4anf,r qtq,or 6.{rn dr} h 5q{id ffqr drit
zz. &'cR 6) fufir4 am Btrlft-a ffiffiira qzi qFii{rild fr A't rri srErrra h ripr ffiq 614
ffid
orarflffi Ftrrr
zs. til-Er o.t ffiq t ftifud frq-drr4-6 (qms6q1 nn.s.S. ffia or 3l-{dr{4 .F-r{ qts{ fi {d
wg-dm$*ffizrzqifttfuo 6i-e{ t 6cilrr:r,6r+aq or{qrila ?i*, rrr$sr qiB-fi t-qI dsnr a<t{
of u-qa orar 6trnr aiidq f aJffi tnr {@ tfr-qR 6t orar ftmr
2e. ffi pra qr F-ariur €rFJn 6r grairz&:o 6r ffi ftfoqrmr 6I Ftrfir
 t
30 ,'{,hr{s,* tfi-fi Efi-e 6p666 sftqs z q(
f
6r ,.4fu srq-Frq q{ dq*q 6r{ 6-{rqr dri4r
trr fufr C gran Efu 6ss1-6 6.{A
11l* Sq,r$ {rft $ dqnq or{ o.rqr arirnr
sr' Bfo. q.'{ d FFd qrffa ,'{s* &E'* ;
614 ,u A ,r$ srqrqfu + e-6 {rqrs,3il*}
f
qm furttta ffifd Efd rg+n lri dr{ dqd.
or4 orar rhrrorfr-rFn
32' tr{. 3rm-{iar,4r$ur qiP*Er s-4r,,Izqrqr
r

il
eiqi{ qr m-. aszotzztfu-ro zar.ci.t. s qrd
Edi6
zg.lt.zozz 3r{grt ffiur ord qr ra qfura S.trs.&.
&cR w iirr+ort
arq Fo-oruror t,il qq-5. t tq 6tn a.{11 srr5r
abnr
sa' rfr'('s'E. fi f f
ar*'r a*r {*,ra o.i cfdq f srrq-Frrq q{ B*d fqil qri qrd ,q-r.
iE
or qrila
fu-qT araT 3IM €trn derr riiifud &qR
h tqo t ,.esr. or Aqfir-{€R +-et*rz5rrara fu_q1
s+ Er€r6R 6) {6 qt'rrff rqld 6-r{r "67n,
il4, Bfuqr qqr 2.10 b. rqs sr, ure r5en Era-qmn rrc
iF<qv4 marr nqa 4€i' 6Ti q{ so,ooo/- qFer6,
6r€ ffi Tqrfud a6. 6'.{i q{ so,ooo/- $qi
qfr4r6 !d ilfi-fa 3r4-d 6r
Tfi ilfle q{ 2s,ooo/-.qE qfr.4T6 u-*r 61 *r+qrfi 6r
ar&frr {6 mqrff
fi ..{s* 3rtf*d rrtr d * bhc* 6r ,.{ilsr fuq'gd .Fr, ..,,a?r r'r (rno) aF tn{,
ote w ?
ga, Ffuqr 3IEiB-d fr qrtrfr,ffir
Rs. qo_s
-*cft
&,_qR a Fbfir
as. qA AfuEroR crr srr{r grqfu f
6rt Wt aO fa.qr orar d Ef+o sq{ ttBw z.ro 6r
t iiBor rs
rg€R $+{Ds 6r otffi fi
ar&rfir
ee. EfucI t
ddfud hrfi g *-lro,a w ue-a wm
or ffiq 3ifrq ati ara ilrnr
sz. EffEr fr f4ifr m s-6n 6r t'eftra qr qfisf,a qfi
ttdr rsor t il rfln 3ilffirtr w Eqr artqr
ffit qe-ar sflrrrn rt{ * fu artnr
c-6rRrd rfi
ra. frgR-opr 6r{ B ECd 6r sfrffd dfiqa q-ag q*
rtar nE-qr{ tr
eg. q*fia * tw nizr+qr€l r-q-d 6rd 6r rmiaa qrq
F}ar q-{arfod Fr

f,ifi )
or{crild ri*,
,Jrfrur qitc-6t C-dr

adt{ {ts{r4 f<tr

g8T. F,'
qFfrfo,-
zdorzBf+ozqr.qi .t. t zo z s 5<t{" trdio /oz/zoz5

1. fuorg $19o,, dsrq-d a?i qrfrq fu+rs fuenrr, h;a{rqd r+a, ftid-q a-o siqrf,l
2. qtra a-6rdqmr, awqhr rqrfuq{ qeEr fr.fr.-+t
3. q-{q $m-{idr, rrr$q qiBdl 0-qr, orqtEq dTff a-s fuors r+a ntr Fm a.q. etqrflr
4. Uq sBziar,ar$ur qiftfi t-qr gat{ qffi{ orcl& $Etrr
5. o-ner, R-or f<trr
6. fl$Erur ?ii, rrrfrq qiB-& +qr 5<tr au-ro orqt@ Fekr
7. gw ordvma Jn6ft,R-dr dqr+d iatl
8. a.q. rnrdrq thqr ('Sfrqcn,32 gs{ a-rr,fuqf,rfi,fi.v+.$.w. rtvrat
9. qilfrr q.fr qr qwt F{t

[p-
?i*,
qimq qiB-Er t-4r

.dt{ ds{rr $-<t{