Scribd
Upload
24 views2 pages

Aw 01

The Coating Inspection Report for the Anchor Winch project by Fiumetech Mechanics Pvt Ltd details the surface preparation and paint application processes, noting that the initial coat was in good condition across 85% of the areas inspected. The report includes specific ambient conditions during the application, including temperature and humidity levels, and confirms compliance with acceptance criteria. The painting system used was a maintenance coating with specified primers and topcoats from the Jotun brand.

Uploaded by

pathantoufik160
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
24 views2 pages

Aw 01

The Coating Inspection Report for the Anchor Winch project by Fiumetech Mechanics Pvt Ltd details the surface preparation and paint application processes, noting that the initial coat was in good condition across 85% of the areas inspected. The report includes specific ambient conditions during the application, including temperature and humidity levels, and confirms compliance with acceptance criteria. The painting system used was a maintenance coating with specified primers and topcoats from the Jotun brand.

Uploaded by

pathantoufik160
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Fiumetech Mechanics Private Limited

Coating Inspection Report

Project Name : Anchor winch Report No:FMPL/P/AW01

Client : S M TOOLS Location : PANVEL FACTORY

Contractor : Fiumetech Mechanics Pvt Ltd.

Details of surface Details of paint application Ambient conditions


preparation
Initial 1st coat 2nd coat 3rd coat 4th coat Date Time Ts(°F) Twb(°F)

2/17/2025 10:00 AM 104 76

Initial coat found in good


Surface preparation grade SSPC SP 01

JOTUN HARDTOP XP
condition 85% areas

JOTAMASTIC 87 AL

(Brand : JOTUN)
(Brand : JOTUN)
2/17/2025 1:00 PM 97 78

Surface profile achieved NA 2/18/2025 1:30 PM 96 78

NA

NA
detergent wash followed by
Abrassive type/Solution
Cleaning thinner 2/18/2025 2:00 PM 92 80

Size of abrasive/Thinner NC Cleaning thinner Acceptance: Relative humidity below 65% and dew point >3
Painting system : Maintenance Coating Conductivity : 16 ms/cm2
Primer : Polyamine cured epoxy mastic 318 486 549 - -
coating. Total DFT (µ)
Intermediate 01 : NA Method of Painting : Conventional Air pot spray, Brush used for stripe coat in edges and s
Intermediate 02 : NA 318 168 63 - - Area Discription : Chain guard cover, Break Liner support pad(4 Nos.), Hydraulic cylinder(
Topcoat : Polyurethane Coating DFT ACTUAL (µ) wheels(4 Nos), Connectors.
9002 GREY RAL 9002 - -
RAL CODE/ COLOUR

Y Y Y - -
Aproved (Y/N)
Remarks : NA - not applicable, Jotun thinner no 17 is used for thinning as per paint manufacturer recomentation.

Name : Execution QC Inspector : PRANAV K V QC Manager : VISHNU NAIR

Date & Signature :

QAC-F-10 Coating Inspection Report


Date : 19-02-2024

nditions

Tdb(°F) RH(%) DP(°F)

91 49 69

87 44 72

92 53 73

91 62 76

w 65% and dew point >3°C than Ts.

for stripe coat in edges and smaller areas.


(4 Nos.), Hydraulic cylinder(2 Nos.), Cover plates, steer

You might also like