(5 TPMS

OPress and hold the left button " { " for three seconds to turn on/off
OThe monitor can automatically power off/on
OWhen the data is abnormal, the device will update the data in real time

1. Device Function
(1)Real-time monitoring of tire presure & tempeEture
(2)Supports solar charging and USB charging
(3)Numbers for tire pressure/temperature alarm en be set
(4)Air leakage alarm, high/low pressure alarm, high temperature alam
(s)Changeable tire position

2. Schematic
Tire pressure unit- , . -Tire temperature unit

Solar charging '. -rs

Ai.3E_E
<:

8.3 1[U/ii.!fi"4
l--ptrl
/P.

t dffit
EAr- -
i
--- Powerdisplay

qP
l|] ll :rP
fPB d"h tr4 ,# h l--"=el \g.-t_o<- Lg5.g
" 'Tire temperature data

Tire pressure data Tire position

3.Screen alarm analysis diagram

Sensor disconnection alam Alarm symbol High tire pressure alarm . Device battery low alarm

Air leaking alam / Low tire pressure alam High temperature alarm
4.Display parameter setting
maximum pressure .

-. milimum temperatuE
pre$ure unit
minimum p@ssure - "o-"4"8ffi8ry
P[ 8"H g "..""'sE'
"E - tempeEture unil

Enterthe setting mode: long press the "M" button for 3 seconds, the buzer "Bi" sounds to enter the setting
mode, and short pres the 'M' button to select the $tting equipment paEmete6, including the pressure unit
(Bar/PsiytempeEtuE unit ( 'C/"Fymaimm pNur€/minimum pressure/maimum temperature, adjust the
paBmeleE by short pressing '<' or ">', and then long press 'M" for 3 s@nds io sve and exit.
(1) PBssure unit setting: when'baifpsi'flashes, pre$ "< " or'>'to slectthe pressure unit, long press the'M'key
to save setting. (Ihe fac{ory defauft is "baf)
(2)TempeEture unit setting: When "C' or "'F ffashes, press '<' or " >" to select the tempeEture unit, and long press
the 'M" key to save the stting. (factory defuult is "C)

(3)Maximum pressure $tting: ln the "PH" setting state, the maximum pressure value flashes, press "{" or
">" to adjust the pressure value, and long press the 'M" key to save the setting. (Adjustable Enge: 0.6-6.0bar, factory
default setting is 3.sbar)

(4)Minimum pressure setting: ln the "PL" stting siate, the minimum pressure value flashes, press "< " or '>" to adjust
the pressure value, and long press the 'M" key to save the setting. (Adjustable range: 0.S5.9bar, factory default setting
is 'l.8bar)

(s)The best temperature setting: in the 'TH" setting siate, the maximum temperature value flashes, press "< " or " >" to
ad.just the temperature value, and long press lhe "M" key to save the setting. (Adjustable range: 50"C-go'Cbar, factory
default setting is 68'C)
5. Display and sensor pairing
(1) Enter the pairing mode: Press the " )" button 8 times continuously, the buzer "Bi" will enter
the pairing mode, the left front wheel flashes, and the display interface is as shown below.

flash --- @E
flash -- -.
H
(2) Pairing: After entering the pairing mode, short press " t'to select the tire to be paired. At this
time, inflate the tire or screw the sensor to the air nozzle. After the display receives the signal, 'Lf,'
will become data, indicating the tire The pairing is successful, press " >" to select the next tire to
be paired, and after all are paired, long press the "M" button to save the settings.

paired successfully .- ""'-'-"'F q

Llra *D,.d
,A
a[\...-4if
G Note: long press the
"< " key can not
uil
H save the settings

6.Swap sensor positions

(1) Enter the sensor position exchange mode: press the "M" key 10 times continuously, the buzzel
"Bi" will enter the tire eichange mode, and will "FL" flash, as shown in the figure below.
FL wheel flashes
FL wheel symbol
. -

trL ffitr- @
r--
t- FR wheel symbol

RL wheel symbol '--e8- FL H-- d' 6'' '

(2) Setting operation: After entering the setting page, short press "M" to select the first sensor to be
RR wheel symbol

exchanged; after the selection is successful, its symbol will flash, then press the " > " key to adjust
the second sensor to be exchanged, and then Press the "M" key to confirm the swap, and finally
press and hold the 'M" key to save the settings.

FLFF ffitrL r= Note: long press the

"< " key can not

*LFg-Hoo FF
save the settings

7. Equipment parameters
-;;EA-- Part :xtemal sensor lntemal sensor Display
Working frequency 433.9200MH2 t 0.1 Mhz

Operatinq Voltaqe 3V 3V 3.7V

Static<1uA Static<1uA Static<50u4
Working current
<1smA (15mA <5mA
surroundings temperature 20'c - +80'c -40'C - +120'C 40'c - +70'c
Monitoring temperature -40"C - +120'C
range pressure 0 - SBar
temperature !2"C
Precision
pressure t 0.'l Bar

S.Sensor installation External sensor installation

Built-in sensor installation Battery replace