0% found this document useful (0 votes)
40 views19 pages

10 FL 010

This technical bulletin addresses DTC P2135/P0638 and cold engine RPM fluctuations in specific Hyundai models, requiring throttle position sensor replacement and ECM software updates. It adds the Genesis Sedan to the applicability list and provides detailed instructions for performing the necessary repairs. The bulletin emphasizes the importance of selecting the latest ECM update events during the repair process.

Uploaded by

tanner.wix
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
40 views19 pages

10 FL 010

This technical bulletin addresses DTC P2135/P0638 and cold engine RPM fluctuations in specific Hyundai models, requiring throttle position sensor replacement and ECM software updates. It adds the Genesis Sedan to the applicability list and provides detailed instructions for performing the necessary repairs. The bulletin emphasizes the importance of selecting the latest ECM update events during the repair process.

Uploaded by

tanner.wix
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Technical Service Group

FUEL SYSTEM
Bulletin Number
10-FL-010
Subject Date
DTC P2135/P0638 OR COLD ENGINE RPM AUGUST, 2010
FLUCTUATION - TPS REPLACEMENT &
Model EN VERACRUZ, CM SANTA FE,
ECM UPDATE TG AZERA, EP ENTOURAGE,
NF SONATA, BH GENESIS

CIRCULATE TO: [ ] GENERAL MANAGER [X] PARTS MANAGER [X] TECHNICIAN


[X] SERVICE ADVISOR [X] SERVICE MANAGER [X] WARRANTY MGR [ ] SALES MANAGER

NOTE: This bulletin revises TSB 09-FL-003-2 to add the Genesis Sedan (BH)
model to the applicability list. It also provides instructions to select the
most recent available ECM Update Events #166-178 or any higher event
numbers if they become available in the future.

DESCRIPTION:
Symptom/Condition:
Some 2.7L, 3.3L or 3.8L engines in models identified in the applicability list may
experience one or more of the following conditions:
• DTC P2135: Throttle position sensors 1/2 voltage correlation
• DTC P0638: Throttle actuator control range/performance
• RPM fluctuation while engine is cold (DTC not set)
NOTE: Should either of the above DTC occur, the vehicle would have operated in
limited power “limp home” mode and stored the following DTC in the ECM:
• DTC P1295: ETC System Malfunction - Power Management
• DTC P2106: ETC System Malfunction - Forced Limited Power
APPLICABILITY:
• 2007-2009 EN Veracruz
• 2007-2009 CM Santa Fe
• 2006-2009 TG Azera
• 2007-2008 EP Entourage
• 2006-2009 NF Sonata with 3.3L Engine only
• 2009-2010 BH Genesis Sedan

Page 1 of 19
REPAIR ACTION:
• Replace the Throttle Position Sensor (TPS)
• Perform the ECM software update.
NOTE: Always perform a GDS ECM Update by Automatic Mode first as it performs
error checking to ensure the correct data is flashed into the vehicle. Always
select the latest available ECM Update event data at time of your update.
NOTE: Do not use ECM Update Manual Mode unless you experience a failure during
the reflash process. It is essential under manual mode that the correct ECM is
selected for the vehicle. If an incorrect ECM is selected, the car may not run.
Most vehicles do not have an immobilizer so one of the NON IMMO ECMs
should be selected for these vehicles.

PARTS REQUIRED:
Order the TPS part kit according to the applicable engine:

Page 2 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

ECM ROM ID INFORMATION:


NOTE: This TSB applies if your incident vehicle ROM ID is found in the PREVIOUS
column of the below ROM ID Table.
NOTE: The ROM ID in the NEW column was the latest available ROM ID at the date of
this TSB publication however, you may select a later event number if one is
shown in the ECM update list even if it describes another issue. This would
generate a more recent ROM ID than shown below but it also includes the
update from this TSB.
NOTE: K-Line and CAN are different scantool communication protocols. CAN is faster
for an ECM update than K-LIne.
CM Santa
CM SantaFeFe2.7L
2.7L with
with K-Line (2007MY)
K-Line(2007MY) - Upgrade
- Upgrade eventevent
#176 #176
MODEL ROM ID
Trans. ECM P/N
YEAR PREVIOUS NEW
CM7N27*S2M5642B*
CM7N27*S2M5652A*
CM7N27*S2M5652B*
CM7N27*S2M5652C*
CM7N27*S2M5653A*
39109-
M/T CM7N27*S2M5652D* CM7N27*S2M5685A*
3E370
CM7N27*S2M5653B*
CM7N27*S2M5660A*
CM7N27*S2M5671B*
CM6N27*S2M5672A*
CM7N27*S2M5683E*
CM7N27*S2WS642BB
CM7N27*S2WS652AA
CM7N27*S2WS652BA
2007MY CM7N27*S2WS652CA
CM7N27*S2WS653AA
A/T 39109-
CM7N27*S2WS652DA CM7N27*S2WS685AA
4WD 3E030
CM7N27*S2WS653BA
CM7N27*S2WS660AB
CM7N27*S2WS671BB
CM6N27*S2WS672AA
CM7N27*S2WS683EA
CM7N27*S2AS642BB
CM7N27*S2AS652AA
CM7N27*S2AS652BA
A/T 39109- CM7N27*S2AS652CA
CM7N27*S2WS685AA
2WD 3E330 CM7N27*S2AS653AA
CM7N27*S2AS652DA
CM7N27*S2AS653BA
CM7N27*S2AS683EA

Page 3 of 19
CM Santa
SantaFe
Fe2.7L
2.7Lwith
with CAN (2008 ~ 2009MY)
CAN(2008~2009MY) - Upgrade
– Upgrade event #177
event #177
MY/Trans. ROM ID
ECM P/N
PREVIOUS NEW
CM7N27*S2M57G3C*
CM7N27*S2M57J0A*
2008MY CM7N27*S2M57J1A*
39109-3E372 CM7N27*S2M57M6A*
M/T CM7N27*S2M57K6A*
CM7N27*S2M57K6B*
CM7N27*S2M57M0E*
CM8N27*S2M58JFA*
2009MY CM8N27*S2M58JGE*
39109-3E374 CM8N27*S2M58JWA*
M/T CM8N27*S2M58JHA*
CM8N27*S2M58JHB*
CM7N27*S2WS7G3CA
CM7N27*S2WS7J0AA
39109-3E032
2008MY CM7N27*S2WS7J1AA
CM7N27*S2WS7M6AA
A/T 4WD CM7N27*S2WS7M0EA
CM7N27*S2WS7K6BA
39109-3E033
CM7N27*S2WS7M0EA
CM8N27*S2W58JFAA
2009MY CM8N27*S2WS8JGEA
39109-3E034 CM8N27*S2WS8JWAA
A/T 4WD CM8N27*S2WS8JHAA
CM8N27*S2WS8JHBA

CM
CM Santa Fe3.3L
Santa Fe 3.3Lwith
withK-line(2007MY)
K-line (2007MY) - Upgrade
- Upgrade eventevent
#166 #166
MODEL ROM ID
ECM P/N
YEAR PREVIOUS NEW
CM6N33*S2AS642BB
CM6N33*S2AS652AA
CM6N33*S2AS653AA
CM6N33*S2AS652BA
CM6N33*S2AS653CA
CM6N33*S2AS653DA
CM6N33*S2AS653EC
39110 - 3C560 CM6N33*S2AS685AA
CM6N33*S2AS671AA
CM6N33*S2AS671BA
CM6N33*S2AS671DA
2007MY
CM6N33*S2AS671FA
CM6N33*S2AS671HA
CM6N33*S2AS683AA
CM6N33*S2AS684AA
CM6N33*S2AS671CA
CM6N33*S2AS671EA
CM6N33*S2AS671GA
39110 - 3C561 CM6N33*S2AS685BA
CM6N33*S2AS671JA
CM6N33*S2AS683BA
CM6N33*S2AS684BA

Page 4 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

CM
CM Santa Fe 3.3L
Santa Fe 3.3Lwith
withCAN(2008~2009MY)
CAN (2008 ~ 2009MY) - Upgrade
– Upgrade eventevent
#167 #167
MODEL ROM ID
ECM P/N
YEAR PREVIOUS NEW
CM7N33*S2AS7G3BA
CM7N33*S2AS7J0AA
39110 - 3C562 CM7N33*S2AS7J1AA CM7N33*S2AS7M6AA
CM7N33*S2AS7M0BA
CM7N33*S2AS7M1AA
CM7N33*S2AS7J0AP
2008MY
CM7N33*S2AS7J1AP
39110 - 3C563 CM7N33*S2AS7M6AP
CM7N33*S2AS7M0BP
CM7N33*S2AS7M1AP
CM7N33*S2AS7K6AP
39110 - 3C564 CM7N33*S2AS7M0CP CM7N33*S2AS7M6BP
CM7N33*S2AS7M1BP
CM8N33*S2AS8JFBP
CM8N33*S2AS8JHBP
2009MY 39110 - 3C565 CM8N33*S2AS8JHCP CM8N33*S2AS8JWBP
CM8N33*S2AS8JKBP
CM8N33*S2AS8JXAP

NF Sonata
Sonata3.3L
3.3Lwith
with K-line (2006 ~ 2007MY)
K-line(2006~2007MY) - Upgrade
- Upgrade event #168
event #168
MODEL ROM ID
ECM P/N
YEAR PREVIOUS NEW
NF5N33*S2AS5B0AA
NF5N33*S2AS5B0BB
NF5N33*S2AS5B3BB
NF5N33*S2AS5B3CB
NF5N33*S2AS5B3DB
2006MY 39110 - 3C760 NF6N33*S2AS685AA
NF5N33*S2AS5E1BC
NF5N33*S2AS5E1DD
NF5N33*S2AS5E2AA
NF6N33*S2AS683AA
NF6N33*S2AS684AA
NF6N33*S2AS642CB
NF6N33*S2AS653BA
NF6N33*S2AS653CC
2007MY 39110 - 3C761 NF6N33*S2AS671AA NF6N33*S2AS685BA
NF6N33*S2AS671BA
NF6N33*S2AS683AA
NF6N33*S2AS684AA

Page 5 of 19
NF Sonata 3.3L with CAN (2008~2010MY) - Upgrade event #169

ECM ROM ID
MODEL YEAR REMARKS
P/N PREVIOUS NEW
NF7N33*S2AS7F4BB NOTE: VIN writing
NF7N33*S2AS7F4CB needed for these 2 ROM

39110- NF7N33*S2AS7G3BA
NF7N33*S2AS7J0AA NF7N33*S2AS7M6AA
3C762
NF7N33*S2AS7J1AA
2008MY
NF7N33*S2AS7M0AA
NF7N33*S2AS7M2BA
NF7N33*S2AS7J1AP
39110-
NF7N33*S2AS7M0AP NF7N33*S2AS7M6AP
3C764
NF7N33*S2AS7M2BP

NF8N33*S2AS8J9AA
NF8N33*S2AS8JAAA
NF8N33*S2AS8JACA
39110-
2009MY NF8N33*S2AS8JADA NF8N33*S2AS8JWBA
3C765
NF8N33*S2AS8JFBA
NF8N33*S2AS8JHBA
NF8N33*S2AS8JKBA
39110- NF9N33*S2AS8JNAA
2010MY NF9N33*S2AS8JNCA
3C766 NF9N33*S2AS8JNBA

BH 3.8L with CAN - Upgrade event #178


ROM ID
IMMOBILIZER ECM P/N
PREVIOUS NEW

BH8N38*M2**8L2AE
39106-3C011 BH8N38*M2**8N2BE BH8N38*M2**8N2DE
With BH8N38*M2**8N2CE

39106-3C013 BH8N38*M2**8P1AE BH8N38*M2**8P1BE

BH8N38*M2**8L2A*
39106-3C010 BH8N38*M2**8N2B* BH8N38*M2**8N2D*
Without BH8N38*M2**8N2C*

39106-3C012 BH8N38*M2**8P1A* BH8N38*M2**8P1B*

Page 6 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

EP Entourage 3.8L with K-Line(2007MY) - Upgrade event #172


MODEL ROM ID
ECM P/N
YEAR PREVIOUS NEW
VQ5N38*S2AS5D1BA
VQ5N38*S2AS5D2AA
VQ5N38*S2AS5E1BB
VQ5N38*S2AS5E2AA
VQ5N38*S2AS5E3AA
39110-3C460 VQ5N38*S2AS660AB VQ5N38*S2AS685BA
VQ5N38*S2AS660BB
VQ5N38*S2AS671CB
VQ5N38*S2AS671DB
2007MY VQ5N38*S2AS683BB
VQ5N38*S2AS683CB
VQ6N38*S2AS653DB
VQ6N38*S2AS660AB
VQ6N38*S2AS671BA
VQ6N38*S2AS671DA
39110-3C465 VQ6N38*S2AS685BA
VQ6N38*S2AS671EA
VQ6N38*S2AS671FA
VQ6N38*S2AS683BB
VQ6N38*S2AS683CB

EP Entourage 3.8L with CAN(2008MY) – Upgrade event #173


MODEL ROM ID
ECM P/N
YEAR PREVIOUS NEW
VQ7N38*S2AS7G3BA
VQ7N38*S2AS7J0AA
39110-3C466 VQ7N38*S2AS7J1AA VQ7N38*S2AS7M6BA
VQ7N38*S2AS7M0AA
VQ7N38*S2AS7M0CA
VQ7N38*S2AS7G3BP
VQ7N38*S2AS7J0AP
VQ7N38*S2AS7J1AP
2008MY
39110-3C467 VQ7N38*S2AS7J2AP VQ7N38*S2AS7M6BP
VQ7N38*S2AS7J2BP
VQ7N38*S2AS7M0AP
VQ7N38*S2AS7M0CP
VQ7N38*S2AS7K6BP
VQ7N38*S2AS7K6CP
39110-3C468 VQ7N38*S2AS7M6BP
VQ7N38*S2AS7M0AP
VQ7N38*S2AS7M0CP

Page 7 of 19
EN Veracruz 3.8L with CAN - Upgrade event #174
ECM ROM ID
IMMOBILIZER REMARKS
P/N PREVIOUS NEW
Immobilizer
key teaching
EN6N38*M2**7E0E*
(except smart
EN6N38*M2**7F4A*
key) and VIN
EN6N38*M2**7F4C*
With 39106 - writing
EN6N38*M2**7F4E* EN7N38*M2**8JNA*
(2007MY) 3C410 procedures
required
EN7N38*M2**8JHA*
EN7N38*M2**8JHB* -
EN7N38*M2**8JHD*
EN6N38*S2**7E0E*
VIN writing
EN6N38*S2**7F4A*
procedure
EN6N38*S2**7F4C*
Without 39106 - required
EN6N38*S2**7F4E* EN7N38*S2**8JNA*
(2007MY) 3C460
EN7N38*S2**8JHA*
EN7N38*S2**8JHB* -
EN7N38*S2**8JHD*
EN7N38*M2**7G3B*
EN7N38*M2**7G3C*
EN7N38*M2**7J0A* EN8N38*M2**8JXA*
With 39106 - EN7N38*M2**7J1A*
(2008MY) 3C411 EN8N38*M2**8JVA*
EN8N38*M2**8JHA*
EN8N38*M2**8JHC* EN8N38*M2**8JWA*
EN8N38*M2**8JHJ*
EN7N38*S2**7G3B*
EN7N38*S2**7G3C*
EN8N38*S2**8JXA*
EN7N38*S2**7J0A*
Without 39106 -
EN7N38*S2**7J1A*
(08MY) 3C461
EN8N38*S2**8JHA*
08MY
EN8N38*S2**8JHC* EN8N38*S2**8JWA*
EN8N38*S2**8JHJ*
EN7N38*M2**7J1B*
EN7N38*M2**7J2B* EN8N38*M2**8JXB*
With 39106 - EN8N38*M2**8JVB*
(2008MY) 3C412 EN8N38*M2**8JHB*
EN8N38*M2**8JHD* EN8N38*M2**8JWB*
EN8N38*M2**8JHK*
EN7N38*S2**7J1B*
EN8N38*S2**8JXB*
EN7N38*S2**7J2B*
Without 39106 -
(2008MY) 3C462 EN8N38*S2**8JHB*
EN8N38*S2**8JHD* EN8N38*S2**8JWB*
EN8N38*S2**8JHK*

Page 8 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

EN Veracruz 3.8L with CAN - Upgrade event #174


ECM ROM ID
IMMOBILIZER REMARKS
P/N PREVIOUS NEW
EN8N38*M2**8JAA*
With 39106 -
EN8N38*M2**8JHB* EN8N38*M2**8JNA*
(2009MY) 3C414
EN8N38*M2**8JHL*
EN8N38*S2**8JAA*
Without 39106 -
EN8N38*S2**8JHB* EN8N38*S2**8JNA*
(2009MY) 3C464 09MY
EN8N38*S2**8JHL*
With 39106 -
EN8N38*M2**8JKD* EN8N38*M2**8JNB*
(2009MY) 3C415
Without 39106 -
EN8N38*S2**8JKD* EN8N38*S2**8JNB*
(2009MY) 3C465

SERVICE PROCEDURE:

TPSUPGRADE
ECM REPLACEMENT PROCEDURE
PROCEDURE

NOTE: The below procedure is performed on an AZERA (TG) 3.3L vehicle, but there is
no need to remove ETC assembly for TPS replacement on all affected vehicle
models.
1. Remove the engine cover, the air intake
hose and the air cleaner upper cover.

Page 9 of 19
2. Disconnect the TPS connector.

3. Remove the 3 TPS mounting bolts (T-20).

4. Replace the TPS, O-ring and 3 bolts with


the new ones.
NOTE: Only 3 of the 4 available mounting
holes are used.
CAUTION:
• Apply clean engine oil around a new
O-ring before installing a new TPS.
• Align the TPS terminals (below
picture) with the mating motor
terminals before installing a new TPS.

Page 10 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

ECM UPDATE PROCEDURE


ECM UPGRADE PROCEDURE

GDS SYSTEM AND ECM UPDATE PRECAUTIONS:

CAUTION: Please verify the following items before performing the ECM update:
• Make sure the vehicle's battery has reasonable charge. If the vehicle has been in
storage, run the engine to ensure an adequate battery charge state for reliable
update results. The ECM Update procedure contains a check to verify that
battery voltage is above 12 volts to allow the procedure to occur.
• The USB cable must be used for ECM Update between the GDS and VCI. The
procedure will not work in VCI wireless mode.
• Make sure the GDS laptop battery indicator in the lower right tray icons has 50%
or more charge (half bar on the battery symbol). Charge the laptop battery with
the AC adaptor cable if the charge is less than 50%.
• Turn off all lamps (do not leave head lamp switch in auto mode) and all
accessories (including heater, A/C, blower, radio, seat warmer, defroster, etc.) to
prevent battery discharge during the update.
• Perform update with the ignition switch in the ON position.
• Be careful not to disconnect any cables connected to the vehicle or scan tool
during the update.
• Do not start the engine during update.
• Do not turn off the ignition switch during update.

Page 11 of 19
INTERNET UPDATE OF GDS SOFTWARE VERSION:
NOTE: This GDS update may be necesary to ensure your GDS has the latest
possible ECM Updates.
1. Close the GDS program and restart it with internet connected to the GDS.
2. Wait for the following GDS Update Program to launch within approximately a
minute. It will inform you if there is an update as shown below.
3. If update is available press OK and follow instructions to update the GDS software
version followed by the VCI firmware level if it also exists.
NOTE: You must have VCI connected to GDS by USB cable to update the VCI.

4. Perform Download followed by Update Start and then Exit when completed..

Page 12 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

GDS AUTO MODE ECM UPDATE PROCEDURE:


1. Turn the vehicle’s ignition key to the ON position.
2. Select ECU Upgrade on the initial GDS home page screen. If you are not at the
home page double click at GDS at top left of the screen to go back to home page.
3. GDS will automatically determine the vehicle information based on the VIN it reads
from the vehicle’s ECM, then select Engine Control as system and OK.
4. Select Auto Mode then ENGINE then OK so the ROM ID will be read:

5. After reading the ROM ID if there is an available update it will display a screen with
the available updates for the vehicle. Select the latest available (highest
number) update event even if it describes another issue. After clicking the
Upgrade button then click OK.
GDS Data Event # Update Event Description
166* CM 3.3 ECM UPDATE - K LINE (07MY)
167* CM 3.3 ECM UPDATE - CAN (08-09MY)
168* NF 3.3 ECM UPDATE – K LINE (06~07MY)
169* NF 3.3 ECM UPDATE – CAN (08~09MY)
170* TG 3.8 ECM UPDATE – K-LINE (07MY)
171* TG 3.8 ECM UPDATE – CAN (08-09MY)
172* EP 3.8 ECM UPDATE – K-LINE (07MY)
173* EP 3.8 ECM UPDATE – CAN (08MY
174* EN 3.8 ECM UPDATE
175* CM 2.7 ECM UPDATE - K LINE (07MY)
176* CM 2.7 ECM UPDATE - K LINE (07MY)
177* CM 2.7 ECM UPDATE - CAN (08-09MY)
178* BH 3.8 ECM UPDATE

NOTE: *Event#166-178 as shown in the table above were latest events at time
this TSB was issued. However be sure to select the highest number
event available in the list even if it describes another issue. It will ensure
the vehicle receives latest possible available ECM data including the fix
for this TSB.

Page 13 of 19
6. This screen is example only. Your screen will show the current ROM ID and latest
ROM ID for update based on the event that you select. Choose the latest
available (highest number) event as explained in the prior note.

Always choose highest event


number from this event list
to get latest ECM data.

NOTE: An error message may appear instead of the above if the ECM Update
had already been completed or is not available for your vehicle.
7. After selecting the Upgrade button the vehicle battery voltage is checked to make
sure it is at least 12 volts required to ensure reliable update results. Select OK if
the results indicate voltage is above 12 volts.
CAUTION: If voltage is below 12 volts, then select Cancel and run the engine at idle
for at least 10 minutes to ensure an adequate battery charge state for
reliable update results.
8. Updating will occur until 100% is reached on the bar graph, then the confirmation
screen will be displayed. Turn the ignition key OFF for 10 seconds, place it back in
the ON position and then select OK.
9. Select OK on the final screen, which indicates update is complete.

Page 14 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

10. For EN Veracruz after update is


completed, perform the VIN writing
procedure or immobilizer key teaching
procedure on the affected vehicles where it
is referenced in the "ECM ROM ID
INFORMATION " table earlier in this TSB.

11. Check for and erase DTC found in each system of ENGINE, A/T, ABS/ECS, and
EPS as a result of temporary loss of CAN communication during the ECM Update.
12. Start the engine to confirm proper operation of the vehicle.

GDS MANUAL MODE ECM UPDATE PROCEDURE:


NOTE: Manual Mode ECM Update is intended to be used only if Auto Mode ECM
Update had failed after the progress bar began during the update.
IMPORTANT: You must reset the ECM by disconnecting the ECM connectors for
10 minutes and then reconnecting them before trying the Manual
Mode ECM Update.
1. Turn the vehicle’s ignition key to the ON position.
2. Within the ECU Upgrade screen, select ENGINE, Manual Mode, and then select
the appropriate event number from the table provided in Auto mode.
3. Select the appropriate control unit part number with reference to the ROM ID
Information Table and then perform Upgrade.

Page 15 of 19
NOTE: This screen is example only. Be careful to select the correct ECM part number
using ROM ID table to help. If in doubt remove ECM to read the part number.
It is critical in manual mode to select the correct system and password.

4. Enter the Event password from the table below and then select OK.
CM SANTA FE 2.7/3.3 ECM UPDATE - K LINE
MENU PASSWORD
CM 2.7 5MT NON IMMO: 39109-3E370 3370
CM 2.7 AT NON IMMO: 39109-3E030/330 3330
CM 3.3 NON IMMO: 39110-3C560 3560
CM 3.3 NON IMMO: 39110-3C561 3561
CM SANTA FE 2.7 ECM UPDATE - CAN
MENU PASSWORD
CM 2.7 5MT NON IMMO: 39109-3E372 (08MY) 3372
CM 2.7 5MT NON IMMO: 39109-3E374 (09MY) 3374
CM 2.7 AT NON IMMO: 39109-3E032/033 (08MY) 3033
CM 2.7 AT NON IMMO: 39109-3E034 (09MY) 3034
CM SANTA FE 3.3 ECM UPDATE - CAN
MENU PASSWORD
CM 3.3 NON IMMO: 39110-3C562 (08MY) 3562
CM 3.3 NON IMMO: 39110-3C563 (08MY) 3563
CM 3.3 NON IMMO: 39110-3C564 (08MY) 3564
CM 3.3 NON IMMO: 39110-3C565 (09MY) 3565

Page 16 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

ENVERACRUZ
EN VERACRUZ 3.83.8
ECMECM UPDATE
UPDATE
MENU PASSWORD
EN 3.8 07MY IMMO: 39106-3C410 3410
EN 3.8 07MY NON IMMO: 39106-3C460 3460
EN 3.8 08MY IMMO: 39106-3C411 3411
EN 3.8 08MY NON IMMO: 39106-3C461 3461
EN 3.8 08MY IMMO: 39106-3C412 3412
EN 3.8 08MY NON IMMO: 39106-3C462 3462
EN 3.8 09MY IMMO: 39106-3C414 3414
EN 3.8 09MY NON IMMO: 39106-3C464 3464

BH Genesis
BH GENESIS 3.83.8
ECMECM UPDATE
UPDATE:
MENU PASSWORD
BH 3.8: 39106 - 3C011 3011
BH 3.8: 39106 - 3C010 3010

NF
NF SONATA
3.3 P2135 3.3
ECM P2135 ECM
UPDATE UPDATE - (06~07MY)
– (06~07MY)
MENU PASSWORD
NF 3.3 NON IMMO: 39110-3C760/61 3761
NF
NF SONATA 3.3 ECM
3.3 ECM UPDATE UPDATE - (08~09MY)
– (08~09MY)
MENU PASSWORD
NF 3.3 08MY NON IMMO : 39110-3C762 3762
NF 3.3 08MY(PA) NON IMMO : 39110-3C764 3764
NF 3.3 09MY NON IMMO : 39110-3C765 3765

Page 17 of 19
TGAZERA
TG AZERA3.83.8
ECMECM UPDATE
UPDATE - K-LINE
– K-LINE
MENU PASSWORD
TG 3.8 39110-3C210/11 3211
TG
TGAZERA
AZERA 3.8 ECM
ECMUPDATE
UPDATE– -CAN
CAN
MENU PASSWORD
TG 3.3 07MY IMMO: 39110-3C310 3310
TG 3.3 07MY NON IMMO: 39110-3C360 3360
TG 3.3 08MY IMMO: 39110-3C311/12 3312
TG 3.3 08MY NON IMMO: 39110-3C361/62 3362
TG 3.3 09MY IMMO: 39110-3C313 3313
TG 3.3 09MY NON IMMO: 39110-3C363 3363
TG 3.8 08MY IMMO: 39110-3C212 3212
TG 3.8 08MY IMMO: 39110-3C213(P)/ 14 3214
TG 3.8 09MY IMMO: 39110-3C215 3215

EP
EPENTOURAGE 3.8 ECM
3.8 ECM UPDATE UPDATE - K-LINE
– K-LINE
MENU PASSWORD
EP 3.8 NON IMMO: 39110-3C460 3460
EP 3.8 NON IMMO: 39110-3C465 3465
EP
EPENTOURAGE 3.8 –ECM
3.8 ECM UPDATE CANUPDATE - CAN
MENU PASSWORD
EP 3.8 NON IMMO: 39110-3C466 3466
EP 3.8 NON IMMO: 39110-3C467 3467
EP 3.8 NON IMMO: 39110-3C468 3468
EP 3.8 NON IMMO: 39110-3C469 3469

5. If voltage is below 12 volts, then select Cancel and run the engine at idle for at least
10 minutes to ensure an adequate battery charge state for reliable update results.
6. Updating will occur until 100% is reached on the bar graph, then the confirmation
screen will be displayed. Turn the ignition key OFF for 10 seconds, place it back in
the ON position and then select OK.
7. Select OK on the final screen, which indicates update is complete.
8. Check if any incidental Diagnostic Trouble Codes (DTC) have been created by the
update and clear the DTC (s) present.
9. Start the engine to confirm proper operation of the vehicle.

Page 18 of 19
Technical Service Group
FUEL SYSTEM
Bulletin Number
10-FL-010

WARRANTY INFORMATION:
CAUSAL
OPCODE MODEL OPNAME OPTIME NATURE CAUS E
P/N
TPS REPLACE
08-09MY 35107-
& ECM UP DATE 0.5M/H
CM 2.7L 3E100FFF
(CAN)
35107F00
TPS REPLACE
08-09MY 35107-
& ECM UP DATE 0.5M/H
NF 3.3L 3C100FFF
(CAN)

07-09MY TPS REPLACE


35107-
EN 3.8L & ECM UP DATE 0.6M/H
3C100FFF
(CAN)

35107F01

08-09MY
TPS REPLACE
CM 3.3L, 35107-
& ECM UP DATE 0.6M/H
EP 3.8L, 3C100FFF
(CAN)
TG 3.3/3.8L

TPS REPLACE
07MY 35107-
& ECM UP DATE 0.7M/H
CM 2.7L 3E100FFF
(K-LINE)
35107F02
TPS REPLACE
06-07MY 35107- N69 C40
& ECM UP DATE 0.7M/H
NF 3.3L 3C100FFF
(K-LINE)

TPS REPLACE
07MY 35107-
& ECM UP DATE 0.8M/H
CM 3.3L 3C100FFF
(K-LINE)

35107F03
06-07MY
TPS REPLACE
EP 3.8L, 35107-
& ECM UP DATE 0.8M/H
TG 3.3/3.8L 3C100FFF
(K-LINE)

35107-
35102F04 TPS REPLACE 0.3M/H
3C100FFF
09-10MY
BH

39106-
39110F2F ECM UP DATE 0.3M/H
3C010

Page 19 of 19

You might also like