COMPUTERIZED

VISION TESTER

M o d e l : C V- 7 2 0 0
Operation Manual
Please observe the following precautions when using this product:
·This is a precise instrument. Install and store it where the following normal life
conditions are kept:
temperature (10~40℃), humidity (30~85%) and atmospheric pressure
(70~106kPa).
·Don’t expose this instrument directly to the sun.
·This instrument must be installed in a level and stable place to operate
smoothly. Don’t put anything on this instrument.
·Before using this instrument, connect all the cords correctly.
·Use a power supply within the range of ±10% of the rated voltage (50/60 Hz).
·Turn off the power when this instrument is not used.

1. COMPONENT NAMES AND FUCTIONS

1.1 Main Body

1
 Figure 1
1) Examination window……….The patient’s eyes are observed through the
window, and display lenses are sent here.

2）Near vision illumination……Light up when near vision test, light off when far
vision test.

3）Corneal aligning windows……The position of patient’s cornea can be

observed through the window.

4）Forehead rest knob……………Adjust the forehead position.

5）Near-point rod holder………….The near-point rod is inserted and attached

here.

6）Near-point rod clamp screw…..Fix the near-point rod.

7）Level……………………………Indicated the level position.

8）Leveling knob………………….Levels the instrument body.

9）Forehead rest magnet………….Fix the face shield.

10）Forehead rest…………………The patient’s forehead rests here.

11）Cornea alignment scale………Measures the cornea vertex position.

2
1.2 Accessories

Figure 2
12）Face shield (2 pcs.)………..Attached to the instrument to put the patient’s
face in place.

13）Dust cover…………………Covers and protects the instrument body from

dust and dirt during storage.

14）Forehead rest (2 pcs.) ……. The patient’s forehead rests here. Detachable
by a touch, use one while the other is being
sterilized.

15）Near-point rod……………The card holder is attached at the near point

examination position.

16）Card holder…………………The near-point card is attached.

17）Instruction manual………… Describes instructions about handling the

instrument

18）Near-point card…………….. Contains the near-point chart.

3
1.3 Power Unit

Figure 3

The function of the sockets

ACP Used to connect to the extensive emitting unit.
RM Used to connect to the Auto refractometer
TL Used to connect to the Auto lensmeter
KB Used to connect to the dial controller.
CV Used to connect to the MAIN BODY.

WARNING
To avoid potential danger, do not remove the power unit.

2. PREPARATIONS
2.1 Assembly Of The Near Point Distance Meter

Insert the card holder in the top end of the near-point rod. The card holder is
designed to slide along the rod. As shown in the illustration, insert the
near-point card in the spring attached to the card holder.

4
 Card holder Near point distance meter

Near point card

Figure 4

Next, insert the near-point rod into the near-point rod mount and firmly fasten
with the set screw. When not in use, hold it upright as shown in the next
illustration.

Figure 5

To avoid injury due to contact, do not

bring the face close to the near-point rod.

2.2 Attaching The Face Shield And Forehead Rest

Attach the face shield, as shown in the illustration. The face shield is fixed by
properly mating it with the face shield magnet.

5
 Figure 6

To remove the forehead rest, see it from a side, turn it up and pull off.

To mount the forehead rest, reversely follow the remove procedure.

Figure 7

2.3 Level Adjustment

Before using, make sure the main body is level. If the bubble is not between
two lines, make it level by operating the leveling knob.

2.4 Corneal Aligning Device

The forehead rest move back and forth by turning the forehead rest knob.
With the patient’s forehead set to the forehead rest, look through the cornea
aligning window from about 25cm apart.

6
 Scale Patient's eye

Illumination

Collimator
Approx. 25cm

13.75mm position
Examiner's eye
12mm position

Figure 8
Look at the patient’s eye so that long lines of collimator and scale are aligned,
as shown in the illustration.
If the eye comes on the long line, the spherical power of eyeglass lens is
measured at 12mm from the cornea surface. Short lines are given at 2mm
intervals from the long line.
The dotted line is 13.75mm from the cornea surface. For example, if the
cornea surface is 4mm away (on the second short line from the long line), the
spherical power of eyeglass lens is measured at a position of 12+4=16mm. If
the eyeglass wearing distance and the measuring distance is different,
correction the Forehead rest knob as show in figure 1

2.5 Near Point Card

When the patient wears multi-focal lenses, the eyeglass spherical power is
measured at a near distance.
Bring down the near-point rod. If the near-point rod is almost level, the position
is the measuring position.
The scale of the near-point rod is graduated in cm and inch unit.
Value matching both end lines of the card holder indicate the distance between
the eye and the card.

7
 40

45

Set the desired target on the near-point card attached to the card holder.
To set the target, turn the rotary part at the bottom part of the card. The target
appears in the sight window. Target number of the near-point card and
contents:
Sight window

1 40cm target VA20/50~20/20

2 Target for presbyopia
3 Target for horizontal line
4 Target for horizontal line (40cm
target VA20/20)
5 Target for presbyopia (thin
lines)
6 40cm target VA20/200~20/60
7 Target for astigmatism
Target number display
10 Presbyopia
Target name on patient side
8 40cm target VA20/20
9 Target for vertical line
10 67cm target VA20/200~20/20

3. Button function in control panel

8
Button area divided into three parts from the function in control panel: menu
and auxiliary function key area, testing key area, vision diagram key area.

Button in the menu and auxiliary function key area is as a key

combination, to implement the second function of some keys. Introduction to
LCD will be detailed in the next section

3.1 menu and auxiliary function key area

is for print. It is effective when the screen is measurement screen, print

content detail determined by print setting when environment variables.

* + ：when the screen is measurement interface, quickly reset the

operation board and machine status.

button：when the screen is testing screen, quickly display/hide vision chart

screen.

button：open/close keystone.

* + ：when the screen is testing interface, enter into the menu

screen.

button：combination key

9
3.2 Testing key area

： right eye selection

In the screen of testing, enter this button, open right eye, cover the left eye,
and set current driving board as the right eye testing mode.
In under-defined screen, enter this button, set current step as right eye mode

* + ：in the screen of testing screen, close/open right eye, will not
change the mode of testing eye.

：Left eye selection

In the screen of testing, enter this button, open left eye, cover the right eye,
and set current driving board as left eye testing mode.
In under-defined screen, enter this button, set current step as left eye mode.

* + ：in the screen of testing screen, close/open right eye, will not
change the mode of testing eye.

：binocular option button

In the screen of testing, enter this button, open two eyes, set current driving
board as binocular testing mode.
In under-defined screen, enter this button, change binocular /right and left eye
mode.

* + ：in the screen of testing screen, close/open two eyes at the

same time, will not change the mode of testing eye.

：increase the value of current testing value.

：decrease the value of current testing value.

：In the screen of testing, if not insert cross cylinder, it cover the left
eye automatically, and then insert right cross cylinder, set the dial of right eye
testing, and set cross cylinder as side [1] .

10
 In the screen of testing, if insert cross cylinder, then set cross cylinder as
side [1] .
In under-defined screen, set current auxiliary lens as cross cylinder, testing
eye mode is right left, and the testing parameter is axis.

：In the screen of testing, if not insert cross cylinder, it cover the right
eye automatically, and then insert right cross cylinder, set the current right eye
testing screen, and then set[1].
In the screen of testing, if insert cross cylinder, then set cross cylinder as[2].
In under-defined screen, set current auxiliary lens as cross cylinder, testing
eye mode is right left, and the testing parameter is axis.
[DIAL]：In the screen of testing, alter the value of current testing item.
Clockwise rotation: decrease the value of the current item.
Counterclockwise rotation: increase the value of the current item.
In under-defined screen, set as the alteration of the data.
[SET]：
In the screen of testing, if it is under the standard program or under-defined

program, it will executive the next step automatically;* + [SET]: back to

the previous step.
In under-defined screen saver the editing content, and then enter to the next
step to edit.

* +[SET]： save the editing content, and return to the previous step
program editor.

In the screen of testing screen,* +[SET]：enter into the calibration

program. After calibrated, restart the machine.

3.3 Vision diagram key area：

：to add the charts of red/green background.

11
 * + ：When external vision chart display is LCD, it can show the
reverse color.

：Enter/cancel single-line display mode.

* + ：Enter/cancel single-row display mode

：Enter/cancel single chart mode.

：
If the current vision figure in a single line/single display mode, it will show the
corresponding icon above the chart. If icon is on the first line of the current
vision chart, then switch to the previous chart in the same type, and keep the
eye cover mode the same.
If the current vision figure in a single row/ without eye cover/red/green mode,
the switch to the previous chart in the same type, and keep the eye cover
mode the same.

：
If the current vision figure in a single line/single display mode, it will show the
corresponding icon under the chart. If icon is on the bottom line of the current
vision chart, then switch to the next chart in the same type, and keep the eye
cover mode the same.
If the current vision figure in a single row/ without eye cover/red/green mode,
the switch to the next chart in the same type, and keep the eye cover mode the
same.

：
If the current vision figure in a single display mode, it will show the
corresponding icon left the chart. If icon is the first row first line of the current
vision chart, then switch to the previous chart in the same type, and keep the
eye cover mode the same.
If the current vision figure in a single line mode, position shift to the left row,
, and keep the eye cover mode the same.
If the current vision figure in a without eye cover/red/green cover mode, the
switch to the single-row mode.

* + ：Switch letter/animal/figure/gap circle chart

12
 ：
If the current vision figure in a single display mode, it will show the
corresponding icon right the chart. If ICONS is in the bottom right corner of the
current vision chart, then switch to the next chart in the same type, and keep
the eye cover mode the same.
If the current vision figure in a single row and eye cover mode, position
shift to the right and keep the eye cover mode the same.

If the current vision figure in a without eye cover/red/green cover mode, the
switch to the single-row mode.

* + ：Switch letter/animal/figure/gap circle chart

4. Touch screen and function introduction

4.1 Basic testing interface and function introduction

13
 Figure4.1 introduction of main testing interface block

1) Current data source display

Display the status of the current detection interface data sources.
2) PD value display and PD test button
Display the current PD value of the two eyes. If not under PD detection mode,
press this button, then enter into the PD detection mode; if the current is under
in PD detection mode, press this button, exit PD detection mode. Detailed
please find 4.2.1.
3) The distance adjust button
Display the current near-far status, click here to switch the near- far mode. If
the current is in a far vision mode, it display far vision, click to switch the near
vision mode; If it is under near vision mode, it display near vision, click to
switch far vision mode. Detailed please find 4.2.2.
4) Auxiliary data help information area
Display and switch auxiliary data, help information. Detailed please find 4.2.3.
5) Measure area
The main area of the basic testing interface. Detailed please finds 4.2.4.
6) Current chart
Display the current chart and the cover chart status, click the chart, and enter
into the option menu.
7) Auxiliary lends of the right and left eyes
Display the current auxiliary lens of right and left eye, click the button of left
auxiliary lens, choose left auxiliary lens menu. Click the button of right auxiliary
lens, choose right auxiliary lens menu.
8) Auxiliary function area
According to the current testing mode, display different auxiliary function
buttons. Detailed please find 4.2.5.
9) Load initialize program option button
Click this button, choose and hide the initialize program options.
10) Switch of Prism and VA
14
Switch the main test area, display VA + ADD and status of a prism
11) Option button of data source
Switch the mode of current date source, detailed please find 4.2.6.

4.2 Basic testing interface zone and function description

4.2.1 PD testing button and PD testing mode

The key to realize two functions: display the current eyes PD and enter, exit
pupil distance measurement mode. When entering the PD measurement mode,
the automatic test program is for binoculars PD mode.

Enter the PD measurement mode:

Under PD measurement mode, the main area will display PD testing project.
Blue highlight can input the value to change. Right and left eyes auxiliary
lenses will be automatically inserted the PD measure lenses, VD observation
lamp will automatically open .Auxiliary button area display the option of VD
observation lamp. It can turn the driving plate, or switch the button+, - to adjust
the PD.

15
 Figure 4.2 main test interface into PD measurement mode

Exit PD measurement mode

In PD measurement mode, click the PD test button, or click any button of the
S/ A/C on the main testing interface, it will exit PD measurement mode. PD
measuring lens automatically cut out, VD observation lamp also shut down
automatically.

4.2.2 Distance switch button

The key to realize two functions: switch distance measuring mode and
display the current far and near point detection.

Switch distance measuring mode:

Choose the far or near point detection. After the data is cleared, far point
measurement mode will be selected automatically.

Show the current way of testing:

16
 Near point measurement mode display：

Far point measurement mode display：

*If the current mode is far vision detection, switch to the near vision detection
mode, if not taken near vision detection before, it will automatically copy S +
ADD, C, A degree in far point vision to the S, C, A degree in near vision
detection mode; If the near point detection mode has been completed, will not
copy.
*If the current mode is far point detection, switch to the near vision detection
mode, if not adjusted PD value in the near vision detection mode, it will
calculate corresponding PD value with PD value according to the far vision
mode; If completed the PD adjustment in the near point detection, which it's
irrelevant.

4.2.3 Auxiliary data, help information display field

Data and the help buttons are use for switch the current display status. If
current display is auxiliary data, the data button is in press state, and the help
button is in pop-up state; If the current displays help information, and the data
button in pop-up state, help button in pressed state.

4.2.4 Inspection data display area

As the basic core area of the interface. There are two main status: display
prism test project status and VA + ADD testing project status.

Figure4.3 detecting data area of the prism project

1) Display area of the sphere of right eye and detection mode selection button
for sphere of right eye

17
2) Detection mode selection button of right and left sphere eye
3) Display area of the sphere of left eye and detection mode selection button
for sphere of left eye
4) Display area of the cylinder of right eye and detection mode selection button
for cylinder of right eye
5) Detection mode selection button of right and left cylinder eye
6) Display area of the cylinder of left eye and detection mode selection button
for cylinder of left eye
7) Display area of the right eye axis degree and detection mode selection
button of axis of right eye
8) Detection mode selection button of axis
9) Display area of the left eye axis degree and detection mode selection button
of axis of left eye.

10, 11, 12,13,14,15 is for repeated use area. Under the prism project displays
status, reuse of prism XY model and polar coordinates mode. XY model and
polar coordinates Mode switch
Through auxiliary function buttons.
10) Display area of the right eye prism degree and horizontal prism detecting
mode selection
/ value display area of polar coordinates Mode and detection mode selection
for right eyes
11) Horizontal prism detecting mode selection / detection mode selection in
polar coordinates mode for binoculus.
12) Display area of the left eye prism degree and horizontal prism detecting
mode selection
/ value display area of polar coordinates Mode and detection mode selection
for left eye
13) Display area of the right eye vertical prism degree and vertical prism
detecting mode selection

18
/ value display area of polar coordinates Mode and detection mode selection
for right eyes
14) Binoculus vertical prism degree detection mode selection
/ detecting mode selection of polar coordinates Mode
15) Display area of the left eye vertical prism degree and vertical prism
detecting mode selection
/ value display area of polar coordinates Mode and detection mode selection
for left eyes

Figure 4.4 ADD+VA detecting data area

16) Right eye ADD display area and ADD detecting mode selection
17) Binoculars ADD detecting mode selection
18) Left eye ADD display area and ADD detecting mode selection
*when enter in to ADD, the machine automatically Run automatically to the
near point detection mode, low beam lights opens.
*If current is ADD detecting project, click any button of S/C/A, it exit ADD
detecting mode, the machine automatically Run automatically to the far point
detection mode.
19) Right eye VA value display area and VA input mode selection
20) Binoculus VA detecting mode selection
21) Left eye VA value display area and VA input mode selection
22)
4.2.5 Auxiliary function button area

19
 Figure 4.5 auxiliary function buttons

Under the different detection mode, the auxiliary function button will display
different content and have different functions.
Sphere testing mode:
Function
display Operation content
button
F1 0.25D Set the sphere step as 0.25dptr。
F2 0.5D Set the sphere step as 0.5dptr。

F3 1D Set the sphere step as 1dptr。

F4 3D Set the sphere step as 3dptr。
F5 blank
Cylinder testing mode:
Function
display Operation content
button
F1 -/+ Change the cylinder -/+display mode

F2 blank
F3 blank
F4 blank
F5 blank

Cylinder axis testing mode:

Function
display Operation content
button
F1 0 Set the cylinder step as 0。

20
F2 45 Set the cylinder step as 45。

F3 90 Set the cylinder step 90。

F4 135 Set the cylinder step 135。

F5 A(1)or A（5） Change the cylinder step between 1。~5。

Prism testing mode:
（H,V,R）：
Function
display Operation content
button
F1 0.5 Set the prism step as 0.5Δ
F2 1 Set the prism step as 1Δ
change prism display between the x, y axis and
F3 XY/Rθ
polar coordinates axis

F4 clear Clear the specified prism value

F5 blank

Prism testing mode（θ）：

Function
display Operation content
button
F1 1 Set the prism step as 1。
F2 5 Set the prism step as 5。

change prism display between the x, y axis and

F3 XY/Rθ
polar coordinates axis
F4 clear Clear the specified prism value
F5 blank

4.2.6 Data source selection buttons

NC: the naked eye vision detection mode. In this mode, all the lenses value is
withdraw input VA values.
TL: call out the data of lens meter. You can choose the data import to CV, and
switch to the CV test mode.

21
RM: call out the data of auto refractometer. You can choose the data import to
CV, and switch to the CV test mode.
CV: call out CV data.
FC: final data. Copy the CV data to FC, according to the needs and experience,
adjust the final data.

4.3 Sub Interface function introduction

It includes testing auxiliary sub interface and set sub interface.
Inspection auxiliary sub interface mainly through call out from basic detecting
surface. Mainly includes: EXE21 select sub interface, auxiliary lens selector
interface, visual figure interface, classification vision chart selection interface.
Set interface into the main menu interface need to under the basic testing
interface, after entering, with a specifically key to call out. Mainly includes: the
main menu interface, environment variable Settings interface and time
Settings interface, un-defined program Settings interface.

4.3.1 Visual figure interface selection

Into the vision char interface has two ways: under the basic testing
interface, click the current vision chart display area; in an under-defined
program Settings interface, click the vision chart display area.

Figure 4.6 vision chart selection sub interface

1) Far point icon. Click the below key, external projection device will display
the corresponding visual chart, and set the registered auxiliary lens. In the
non- preview mode, will be automatically returned to the basic test or a
un-defined program editing interface; In preview mode, at position 4, show
the detailed content of vision chart.

22
2) Confirm the back key in Preview mode. Display In preview state, click the
button, switch the currently selected vision chart 4, and back to the basic
test interface or un-defined program editing interface.
3) Does not change the selected current vision chart, back to the basic test
interface or un-defined program editing interface.
4) Display details of the currently selected vision chart.
5) Change the preview/non- preview state
6) close and open external display/projection device.
7) Near point additional lenses testing. Press the icon button; automatically
enter to the near point, near point crossed cylindrical lens inserted into the
front of the eyes.
8) Near point vision test chart. Press the icon button; automatically enter to
the near point mode.
* Under the vision chart selection interface, if the current external projector is
LCD, press [SET] key to enter LCD's Settings menu, press [SET] key
repeatedly to switch SET , through the direction keys to change the current
Settings.

4.3.2 Auxiliary lens selector sub-interface

There are two ways for Auxiliary lens selection export the data: under the basic
testing interface, click on the left/right eye auxiliary lens display area; in an
un-defined program editing interface, click on the left/right eye auxiliary lens
display area.

See lens in details PLS find appendix 1.

Figure4.7 far point right eye auxiliary lens selecting interface

23
 Figure4.8 far point left eye auxiliary lens selecting interface

Figure 4.9 Near point right eye auxiliary lens selecting interface

Figure 4.10 Near point left eye auxiliary lens selecting interface

24
 Click the lens key, will change the current lens inserted in the CV - 7200
auxiliary lens state. And back to the basic test interface or un-defined program
editing interface. Click back button, will not make any change to return to the
previous interface.

4.3.3 EXE select sub-surface

Under the basic testing interface, export the program selection menu, click

,callout EXE21 program select sub-interface.

Figure 4.11 EXE21 program select sub-interface

Click the required procedures, directly back to the main testing interface,
callout the preset test Settings.

4.3.4 Classification vision chart rapid selecting interface

The sub-interface will automatically list and select the same type chart
according to the current selected chart.

Under the main test interface, press button on the panel, callout the
Classification vision chart and rapidly choose preset sub-interface, then click
again, withdraw the Classification vision chart and rapidly choose preset
sub-interface.

25
Figure 4.12 Classification vision chart and rapidly choose preset sub-interface and

current diagram(Chart projector version)

Click the Classification vision chart, is the same as click the far point vision
chart under the sub-surface directly back to the main testing interface, callout
the preset test Settings.

4.3.5 Main menu interface

Under the basic test interface, press + button on the panel，callout

the main menu interface.

Figure 4.13 main menu interface

26
button Operation content
Environment setup Enter to the Environment variable
interface to set
Time setup Enter to time set interface to set

Program setup Enter to preset program editing

selected interface to set
SHIFT+SET Enter to touch screen to calibrate
back Back to main test interface

4.3.6 Environment variable set up interface

Under the main menu interface, click on the "environment Settings" button,
enter the environment variable Settings interface.

Figure 14 Environment variable set up interface

1. Set the options bar. Choose and set the detailed environment variable
value, will display different projects according to the choice 2.
2. Set the options selection area. Select environment variable values need to
change, and shows the specific options in the right setting options bar.
3. Variable value explanation area. Briefly explain the content of the

27
environment variable .
*if there is change to the "external projection device selection", when you back
to previsou menu ,will show button of save restart or give up save.

4.3.7 time set interface

Under the main menu interface, click on the "time setting" button, enter the
time setting interface. Time shows according to the system 24 hours a day.
Year, month, day, hours, minutes, seconds respectively set through
corresponding key .Click on the corresponding button, will pop up input digital
interface. After Setted, press "save" button, save the current time Settings and
return to the main menu interface, if click "exit" button, will not keep the current
time Settings

Figure 4.15 time set interface

4.3.8 Preset program selected interface

Under the main menu, click on the "program Settings" button, enter the
preset program selected interface. Total five defined programs as well as a
standard program option. Click on any one of the button, enter into the
program step interface.

4.3.9 Program list interface

Brief display the every step content , click on the corresponding steps, directly
into the corresponding steps to edit interface. Choose defined program and
standard program, different operating option.

28
 Figure 4.16 defined Program step list interface

Figure 4.17 standard Program step list interface

Standard program steps list display has no "remove" button. "program 1", "
program2”, "program 3", "program 4", " program5” ,the corresponding standard
program steps is copied to the corresponding defined program, and switch the
interface to the defined program step list interface.

29
4.3.10 defined program editing interface

In the program step list interface, click on any step, will enter into a defined
program editing interface

Figure 4.18 defined program editing interface

button Operation content

1 Set to change data source
2 Set to change detecting eyes
3 Set to change the detecting items
4 Set to change if join cross cylinder lens
5 Set to change auxiliary fog value
6 Not save the current modification, back to step list
interface
7 save the current modification, back to step list interface
8 Delete the current step, show next content

9 Save the current content, as a new step to insert the next

step
10 Show the current modification, and turn to the next

30
 content
11 save the current modification, back to the previous step
12 Display the current selected left eye auxiliary lenses, call
out the auxiliary lens selection interface

13 Display the current selected right eye auxiliary lenses,

call out the auxiliary lens selection interface
14 Display the current selected vision chart, call out the
vision chart selecting sub-interface

5．Device operation

5.1 Preparation
5.2 Mode selection
Environment variable Settings the interface, select the start mode setting

Figure5.1 start mode setting

The factory setting default as the standard program. Program 1 to

program5 as user-defined program. If you select "no", it will enter into the
manual setting test project and order by optometrist after open the machine.
If under the process of detection, need to temporary load preset program,

31
it through the button in the main testing interface in LCD panel, then
choose the required program. After entering any program, every click [SET],
the program will be automatically performing the next step. Press [SHIFT] +
[SET], can back to the previous step program.
We suggest optometrist can set program in advance according to the different
types of customers, are stored in "program 1" to "5" program separately. It only
need to callout the corresponding program, it can greatly improve efficiency.
About programming content, will be introduced in 5.8

We will exemplify the operation process when open the machine and
Choose start mode of "no".
A customer buy glasses, always complain of poor vision.
Check firstly his eyeglasses value with lens meter
R：-1.00DS/-0.50DC X 90°
L：-1.25DS/0-0.50DC X 180°
PD=65mm
Corrected vision is only around 0.7, but we can find the basic reason may be
because of the original degree is not enough to cause vision to reduce, now is
required a better glasses prescription.

5.3 Test with fog

5.3.1、set degree + 3.00 D by hand to Right eye sphere value . Because the
customer the right eye degree is -1.00 D, plus + 3.00 D, become + 2.00 D.
5.3.2、the value should be less than 0.1 at this time, project a vision icon by
hand, then gradually adjust the degree, to reduce as per - 0.25 D, from +2.00D
to + 1.75 D, then to + 1.50 D, until his sight value is about 0.5.
5.3.3、call out radiation vision chart:

32
 Figure5.2 radiation vision chart
Ask customer "is there the mostly clear line can you see?"
If the customer answers "look all the same", that means no astigmatism, finish
the measurement.
If the customer answer seems one line is particularly clear , then use
30 °multiply that small size number which of the clearest line, this value
negative correction.
For example:if the third line is the most clear to see,so it is 3X30°=90°
Adjust astigmatism axis, and then adjust the astigmatism value, from 0.00 to
-0.25, then to -0.50, until all the line is the same clear.
5.3.4、as - 0.25 D a unit to adjust the sphere value.以-0.25D
The customer is short sighted, sphere is -1.75 D, after roughly check, his
degree values as shown below figure:

Figure 5.3 testing chart of the customer

33
5.4 accurate astigmatism axis position and degree

5.4.1. Select manually the point chart as following, crossed cylinders

automatically used to the right; or call out the crossed cylinders from the

auxiliary lens with single line chart, or enter or button directly to

inset to crossed cylinders. Jump automatically to A, First take accurate
measurement of astigmatism axis.

Figure 5.4 point chart

5.4.2. Accurate astigmatism axis. enter or to switch the two sides of

crossed cylinders, ask the customer which side is more clearer, if under

mode is more clearer, need to click the front button，if under

mode is more clearer, need to click the front ，device will automatically

adjust the astigmatism axis. then enter and buttons to repeat the
steps before, until the 2 side is the similar clear, can know the accurate
astigmatism axis value.

5.4.3.accurate astigmatism value：after accurate the astigmatism axis,

enter to accurate the astigmatism value（keep crossed cylinders

status）.enter or to switch the two side of crossed cylinders,ask the

customer which side is more clearer, if under mode is more clearer, need

to click the front ，if under mode is more clearer, need to click the front

button ，device will automatically adjust the astigmatism value. Then enter

and buttons to repeat the steps before, until the 2 side is the similar

34
clear, can know the accurate astigmatism value.
Under the condition of Adjust astigmatism value, device can automatically link
with sphere, it means: cylindrical lens change the 0.50 DC .sphere
automatically change + / - 0.25 DS.
The result：-0.50DC×100°

5.4.4 After accurate astigmatism axis and value, enter any chart button

or crossed cylinders will automatically remove.

5.5 Accurate sphere measurement to avoid any deviation

(Test with red and green, if red/green test is not applicable to a customer, can
determine whether there is bias according to the vision situation directly)

Chart red/green ，ask the customer the letter in red/green which is

more clear ,if customer says green, it means accurate too much, need to add

sphere value of+0.25D.or enter green button，device will automatically

increase the value. then ask the customer again, if he answers red is clearer, it

means accurate not enough, add -0.25D，or enter red button，device will
automatically deduce the value。That means the actual value is between
-1.50Dand -1.75D，According to the requirement and need of the customer to
choose high or low. Screen displays at this time:

Figure5.5 Precise sphere measurement interface

35
 conclusion：right eye： -1.50DS/-0.50DC×100°
next to test left eye。Close the right eye，not close the left eye。Step is 步 the
same as right eye, the result of left eye： -2.00DS/-0.50DC×170°
In order to give customers a better eyesight condition, we need to do
binoculus balance test.

5.6 Binoculus balance test.

(Test with polarization separation chart, also can according the sigle line chart
coordinate prism to do balance test)

5.6.1 The binocular projection screen, as below shown in the figure

Figure 5.6 binoculus balance test.

5.6.2 Customers see the top line of picture with right eye, bottom with left eye .
If from top to bottom row is the same clear or fuzzy, it means that the
binocular balance. If not like this, increase sphere+ 0.25D to the eye
which is more clearer, supposed left eye increase +0.25D，it becomes
-1.75DS
Next choose the binocular mode, to do binocular fog，increase sphere
+ 1.00to each eye on the basic of the tested value with drive plate.
So now the value of the lens should be
Right eye： -0.50DS/-0.50DC×100°
Left eye： -0.75DS/-0.50DC×170°
5.6.3 Increase -0.25D for each eye each time，until reach the accurate value.
5.6.4 Cancel binocular cover, it shows at last：

36
 Figure 5.7 result of binoculars balance test

Right eye： -1.50DS/-0.50DC×100°

Left eye： -1.75DS/-0.50DC×170°

5.7 Heterophoria measurement

First test horizontal heterophoria, select binocular mode, use the right eye lens
selecting button and add the red Maddox to the right eye.
Projection point icon, customers will see red vertical lines from right eye (figure
26a), a lighting point from left eye (figure 26b). Two eyes blending images as
shown in figure 26c or 26d. If as shown in 26d, then there is no or a blend low
strabismus, no need to adjust a prism. if as shown in 26 c, use left eye prism
button BI or BO around the mobile lighting, remind customer, when he saw the
picture as shown in figure 26d, hit to stop, test for several times and get the
average.

37
 Figure 5.8 Heterophoria measurement chart
Next to test the vertical heterophoria measurement. Select binocular mode,
use the left eye lens selecting button and add the red Maddox to the left eye.
Cancel the left eye cover.
Customer will see a horizontal red line with left eye, a lighting point from right
eye. Use right prism button to BU or BD to move up/down the lighting points.
Remind customer, when he saw the horizontal line and lighting point ,hit to
stop, test for several times and get the average.
Until now, comes the result.
If heterophoria degree is too big, need to correct with the glasses lens, in this
case the customer is not very serious, so don't need to correct.
The final result is:
Left eye： -1.50DS/-0.50DC×100°
Right eye： -1.75DS/-0.50DC×170°

5.8 design user-defined optometry program

According to 6.3.10 instruction, enter into user-defined optometry program
interface. Here do not introduce the interface and button function again, please
refer 6.3.10. Now use an example to introduce last optometry case:
For example, during the accurate test process, it will use cross-Cylinder,
we can suppose like as below:

First, choose the chart, and press the drive plate button, switch to

“Cylinder”. Because it need use cross-Cylinder, so press , use

38
 and or press the scieropia degree button to add Cloud value. Finally,
you will get the interface as below:

Figure 5.9 The optometry program setting interface of last case

During the Use of Maddox to test heterophoria, you can set as this.
Firstly, choose pointolite, and then press “lens”, the display will show
the auxiliary lens interface.

Picture 5.10 The sketch map of choosing horizontal Maddox

39
 Press , it will automatically return to program design interface.
Setting testing item as “horizontal prism”, and Measured eye as “binoculus”.
And final display will as below picture:

Picture 5.11 The program defined interface of heterophoria test.

For the same reason, optometrist can set every optometry step in the program.
If next time you need use the program, you can choose the corresponding
program from the main testing interface.
During the program setting process, after each optometry step, press [SET]
button, the machine will automatically go to next program (press
[SHIFT]+[SET], it can return to last optometry step). Setting project chart or
choose auxiliary lens can improve
Optometry efficiency

6. Self-inspection and maintain.

6.1 Trouble shooting

When machine CV7200 doesn’t work, please try to eliminate the troubles
according to the next chat.

40
 symptom processing methods
When switch on, the phoropter Make sure the power plug is on the
do not have any response. socket
Make sure the Ophthalmic Unit is switch
on.
Console display disappear The Console enter Screen saver mode.
suddenly Touch the screen or press any button on
the control panel, it will come back to
normal display mode.

Console penal button do not It might work abnormally, pleas turn off
work the power and restart the machine.
Press the print button but without Please change the printer paper.
responce. Make sure the printer paper is installed
properly.
Touch screen click response Please do the calibration for Touch
position deviation
screen
If you can not eliminate troubles with above ways, please contact with the
distributor.

6.2 Change the printer paper.

When the red line appears on the printer paper, it shows the console does not
have enough printers inside. Now you need to replace the printer paper.
Please do not print under no printer paper situation, it will damage the print
head.
Do not tear the printer paper violently; it will cause the printer work abnormally
or even break down the printer.

41
6.2.1Press the switch on the printer cover(as left picture) to open the printer
cover.

6.2.2 Take the remaining paper out.

6.2.3 As the right picture show, put the new paper into the printer
6.2.4 Put paper through the print mouth, then close the cover
(Make sure the printer cover is closed, or the auto cutter will not work)

6.3 Clean the inspection window

When fingerprint, oil of eyelashes or dust are sticky on the inspection

window, accuracy of result will be influenced. Make sure that the inspection
window is clean before inspection. If there has stain, please using soft and
clean cloth to clean it.
If there is water vapor condensation, please unload the mask, then unload
the protection glass, clean it carefully. When unloading the protecting glass u
have to use special screwdriver to unfix four screws.

6.4 change fuse-link

turn off the electric power, pull the power line, then pull out the
power outlet. At the same time, be care for the type of electric

Warning power, means pressure and current should be suitable。Type of

fuse-link is F1AL250V.

42
7．Specifications

Sphere -19.00~+16.75D（0.25D/0.50D/1.00D/3.00D steps）

Cylinder -6.00D~+6.00D 0.25D steps
Axis angle 0~180°（1°/5°steps）
Pupil Distant range 52~80mm Close range 48~76mm
distance 0.5/1mm steps
Rotary 0~20△（0.1△/0.5△/1△ steps）
Prism
Cross ±0.25D
Cylinder
Lens
Retinoscope +1.50D(67cm)，+2.00D(50cm)
PH, Binoculus （￠=1.0mm）
RMV/RMH
RL(Right eye)、GL（Left eye）
Auxiliary Polaroid（Right eye 135°/45°），（Left eye 45°/135°）
Lens Prism（Right 3△BU ，6△BU）， （Left 3△BD, 10△BI）
Cross Cylinder Lens(±0.50D Axis=90°)
PD Lens
Phoropter 365mm×280mm×110mm 3.8kg
size
Keyboard 230mm×195mm×190mm 1.2kg
size
Power Box 236mm×126mm×115mm 2.1kg
Power AC220V 50Hz or AC110V 60Hz，90W
supply

43