2016 > D 1.
7 TCI-U2 > Transmission > D7UF1 > P06B011 Odd Sensor Supply Short to Ground English
>
General Information
Please rate this document after reviewing at the bottom of this page.
GENERAL DESCRIPTION
DCT system is installed 2 Clutchs. The Clutch1 is in charge of 1st, 3rd, 5th,7th gear shift, and The clutch2 is in charge of 2nd, 4th,
6th, Reverse gear shift. The Shift Motor select suitable gear according to Driving condition.
* Thanks for your cooperation for the more quality. Please surely rate this document before
closing.
2016 > D 1.7 TCI-U2 > Transmission > D7UF1 > P06B011 Odd Sensor Supply Short to Ground English
>
Component Location
Please rate this document after reviewing at the bottom of this page.
COMPONENT LOCATION
1. Clutch actuator
2. Shift actuator
3. Select solenoid
* Thanks for your cooperation for the more quality. Please surely rate this document before
English
closing.
2016 > D 1.7 TCI-U2 > Transmission > D7UF1 > P06B011 Odd Sensor Supply Short to Ground English
> DTC
Information
Please rate this document after reviewing at the bottom of this page.
DTC DESCRIPTION
TCM set this code When supply voltage for Odd system(speed sensor1, position1, gear shift1 hall sensor, clutch1 hall sensor) is
below than available range.
DTC DETECTING CONDITION
Item Detecting Condition Possible Cause
DTC Strategy Check the voltage
Enable Condition Battery voltage is above 9V
1. Gate Select Actuator Fault
Threshold Value Sensor supply Voltage less than 7 V
2. Sensor circuit open/short
Detecting Time 4 second
Fail Safe Drive at Even gear
* Thanks for your cooperation for the more quality. Please surely rate this document before
closing.
2016 > D 1.7 TCI-U2 > Transmission > D7UF1 > P06B011 Odd Sensor Supply Short to Ground > DTC
English
Inspection
Please rate this document after reviewing at the bottom of this page.
MONITOR DTC STATUS
1. Connect GDS to Data Link Connector(DLC).
2. Ignition "ON"
3. Monitor "Diagnostic Trouble Codes(DTC)" with GDS.
4. Is DTC status displayed as Present?
▶ Go to "Monitor GDS Data" procedure.
▶ Go to "Verification of Vehicle Repair" procedure.
MONITOR GDS DATA
1. Ignition "OFF"
2. Connect GDS to Data Link Connector(DLC).
3. Engine "ON"
4. Operate vehicle or system in accordance with Enable Condition in DTC Detecting Condition.
5. Monitor selected parameters shown below in "Current Data" with GDS.
Specification : Refer to Figure below
English
Fig.1) Engine "ON" & P gear.
6. Is measured value within specification?
▶ Fault might be intermittent and caused either by poor contact in connectors or wiring harness, or it
has been repaired and control module memory is not cleared yet. Thoroughly check terminal of
battery, all connectors (and connections) for looseness, bending, corrosion, contamination,
deterioration, and/or damage.
▶ Repair or replace as necessary and then go to "Verification of Vehicle Repair" procedure.
▶ Go to "Terminal and Connector Inspection" procedure.
* Thanks for your cooperation for the more quality. Please surely rate this document before closing.
2016 > D 1.7 TCI-U2 > Transmission > D7UF1 > P06B011 Odd Sensor Supply Short to Ground English
> Wiring
Inspection
Please rate this document after reviewing at the bottom of this page.
TERMINAL AND CONNECTOR INSPECTION
1. Many malfunctions in the electrical system are caused by poor harness and terminals.
Faults can also be caused by interference from other electrical systems, and mechanical or chemical damage.
2. Thoroughly check all connectors (and connections) for looseness, bending, corrosion, contamination, deterioration,
and/or damage.
3. Has a problem been found?
▶ Repair as necessary and then go to "Verification of Vehicle Repair" procedure.
▶ Go to "Select 1 Position Sensor Power Circuit Inspection" procedure.
SELECT 1 POSITION SENSOR POWER CIRCUIT INSPECTION
1. Ignition "OFF"
2. Refer to "Shop Manual" and disconnect Gate Select Actuator connector.
3. Ignition "ON"
4. Measure voltage between Pin No. 3 (power) terminal of Gate Select Actuator harness conenctor and chassis ground.
Specification : Appox. 8.8 V
5. Is measured value within specification?
▶ Go to "Input speed sensor Power Circuit Inspection" procedure.
▶ Repair open or short in power circuit between Gate Select Actuator and TCM and then go to
"Verification of vehicle Repair" procedure.
INPUT SPEED SENSOR POWER CIRCUIT INSPECTION
1. Ignition "OFF"
2. Refer to "Shop Manual" and disconnect input speed sensor connector.
3. Ignition "ON"
4. Measure voltage between Pin No. 1 (Power) terminal of input speed sensor harness connector and chassis ground.
Specification : Approx. 8.8 V
5. Is measured value within specification?
▶ Go to "Clutch Motor Hall Sensor Power Circuit Inspection" procedure.
▶ Repair open or short in power circuit between input speed sensor and TCM and then go to
"Verification of vehicle Repair" procedure.
CLUTCH MOTOR HALL SENSOR POWER CIRCUIT INSPECTION English
1. Ignition "OFF"
2. Refer to "Shop Manual" and disconnect Clutch Actuator connector.
3. Ignition "ON"
4. Measure voltage between Pin No. 2 (power) terminal of Clutch Actuator harness conenctor and chassis ground.
Specification : Approx. 8.8 V
5. Is measured value within specification?
▶ Go to "Shift Motor Hall Sensor Power Circuit Inspection" procedure.
▶ Repair open or short in power circuit between Clutch Actuator and TCM and then go to
"Verification of vehicle Repair" procedure.
SHIFT MOTOR HALL SENSOR POWER CIRCUIT INSPECTION
1. Ignition "OFF"
2. Refer to "Shop Manual" and disconnect Gear Shift Actuator connector.
3. Ignition "ON"
4. Measure voltage between Pin No. 3 (power) terminal of Gear Shift Actuator harness conenctor and chassis ground.
Specification : Approx. 8.8 V
5. Is measured value within specification?
▶ Go to "Verification of Vehicle Repair" procedure.
▶ Repair open or short in power circuit between Clutch Actuator and TCM and then go to
"Verification of vehicle Repair" procedure.
* Thanks for your cooperation for the more quality. Please surely rate this document before
closing.
