MATERIALS ENGINEER REFRESHER

EXAMINATION FOR MARCH 2020

PREPARED BY: MARK LOWILL BANAAG ALMEDA
Instruction: Answer the following in 2 hours only.
1. Rate of dilution for each layer of polymer-based 6. How many quality tests are required for
chemical soil additive for Item 206. Concrete Hollow Blocks (CHB) if the total quantity
A. 1:5 to 1:9 to be used in the project is 35,750 units?
B. 1:3 to 1:6 A. 36 QT
C. 1:5 to 1:7 B. 10 QT
D. 1:3 to 1:9 C. 8 QT
D. 4 QT
2. What is the ph Value of water allowed in concrete
mix? 7. A 3.35-meter width single lane pavement has a
A. 4.0 to 8.0 shoulder with of 3.0 meters on each side. The
B. 4.5 to 8.5 combined thickness of subbase and base course
C. 5.5 to 8.5 shall be 400mm. How many layers of Compaction
D. 4.0 to 8.5 of the subbase and base courses must be carried out
if the thickness of the subbase is 200mm?
3. What is the minimum dry compressive strength A. 2 layers over full width of 4.35m
of bituminous mixture? B. 2 layers over full width of 3.35m
C. 3 layers over full width of 4.35m
A. 3.5 MPa
D. 3 layers over full width of 3.35m
B. 4.5 MPa
C. 1.4 MPa
8. Which of the following Schedule No. of
D. 2.5 MPa
Galvanized Iron Pipes is the thickest?
4. If the sample splitter is not available for use in A. No. 10
reducing samples for testing, what is the alternative B. No. 10S
way of reducing sample for testing size for coarse C. No. 5
aggregates? D. No. 160
A. apply quartering method and get two
adjacent sides as samples 9. What is minimum thickness of aluminum
B. apply quartering method and get two sheeting used for warning, regulatory and
opposite sides as samples informatory signs?
C. Obtain sample at the mid, top, bottom. A. 3 mm
D. All of the above B. 5 mm
C. 10 mm
5. What is the compressive strength of the 6" dia. D. 2 mm
cylinder sample if it fails at 105,100 lbs.?
A. 3,720 psi 10. What sieve No. is the maximum particle passing
B. 3,710 psi for Sand used in Field Density Test?
C. 3, 730 psi A. Sieve No. 40
D. 3,725 psi B. Sieve No. 4
C. Sieve No. 10
D. Sieve No. 60

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 1
11. What is the rate of application for Bituminous 18. The Pattern of Reflectorized Rubble strips shall
Prime Coat? finish within _____ of any hazard it is associated
A. 1-2 l/sqm with.
B. 0.9 1.8 l/sqm A. 250m
C. 0.2-0.7 l/sqm B. 100m
D. 1.5-3.0 l/sqm C. 50m
D. 150m
12. This is the minimum thickness of stones to be
used for Stone Masonry. 19. The length and thickness of bituminous
A. 250mm pavement core is obtained from how many
B. 200mm measurements?
C. 150mm A. 4
D. 100mm B. 5
C. 9
13. What is the slump of workable concrete when D. 12
not vibrated?
A. 40-75mm 20. What is the maximum international roughness
B. 10-40mm Index (IRI) for both asphalt and concrete
C. 10-75mm pavements?
D. 45-75mm A. 1.5 m/km
B. 2.0 m/km
14. What is the Young's Modulus of Elasticity of C. 2.5 m/km
Carbon Fiber Sheet? D. 3.0 m/km
A. 230 kN/mm^2
B. 250 kN/mm^2 21. What is the rate of loading of compression
C. 200 kN/mm^2 machine during compression test of cylinder
D. 240 kN/mm^2 samples?
A. 20-50 psi/sec
15. Carbon Fiber Sheet Pull Off bond strength in B. 20-50 psi/min
dry and wet shall have minimum concrete failure of C. 125-175psi/min
____? D.125-175psi/sec
A. 0.5 MPa
B. 1.0 MPa 22. This is a test that determines an aggregate's
C. 1.5 MPa resistance to disintegration by weathering and
D. 2.0 MPa freeze-thaw cycle.
A. Soundness
16. What is the minimum vertical load that the B. Abrasion
reflective pavement studs shall support during C. Durability
testing? D. Decantation
A. 5 kN
B. 10 kN 23. What is the standard oven temperature for
C. 15 kN drying aggregate and soil samples?
D. 20 KN A. 110+-5°C
17. What is the ratio of Mortar used for Grouted B. 105+-5°C
Riprap? C. 115+-5°C
A. 1:1 D. 110+-10°C
B. 1:2
C. 1:3
D. 1.5:2.0

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 2
24. This is a high technology equipment containing
radioactive source that can read in- place density or 30. What is the frequency of core sampling on a
moisture content. completed bituminous pavement?
A. Pycnometer
B. Dynamic Cone Penetrometer A. Every 100 m per lane
C. Nuclear Density Gauge B. Every 200m per lane
D. Seismic Density Gage C. Every 500 m per lane
D. Every 1,000 m per lane
25. These materials are generated when asphalt
pavements are removed for reconstruction, 31. What is the sampling weight of Concrete Joint
resurfacing, or to obtain access to buried utilities. Sealant Cold type?
A. Reclaimed asphalt pavement (RAP)
B. Removed asphalt pavement (RAP) A. 3.785 L
C. Recovered asphalt pavement (RAP) B. 3.875 L
D. Recycled Asphalt Pavement (RAP) C. 3.587 L
D. 4. 875 L
26. What is the dimension tolerance of Gabions?
A. +-5% 32. What is the heating temperature during
B. +-3% application of Reflective Thermoplastic Stripping
C. +-10% Material?
D. +-8%
A. 211+-7°C
27. What is the minimum application thickness of B. 215+-7°C
non-shrink grout? C. 211+-10°C
A. 13mm D. 159°C
B. 25mm
C. 50mm 33. What is the sampling frequency for compressive
D. 10mm strength of shotcrete?

28. The concrete mixtures were not yet discharge A. 1 set per 25 m3 but not less than 1day
for 1 hour and 45 minutes, as ME, what are you B. I set per 50 m3 but not less than 1day
going to do? C. I set per 75 m3 but not less than 1 day
D. 1 set per 20 m3 but not less than 1 day
A. Add more water to the mixer and mix
properly until desired mix is obtained 34. Which of the following Gauge No. of Galvanized
B. Discard the mix Iron Sheets is the thickest?
C. Remix properly the mix
D. Discharge immediately. A. No. 18
B. No. 20
29. What is the proper way of transporting core C. No. 22
/concrete samples to the laboratory for testing? D. No. 30

A. Samples are in crate with saw dust and

rice straw or even sand the least
B. Samples are in crate, immovable
C. Samples are placed in sack
D. None of these

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 3
35. These types of paints are used mainly for 40. How many Grading Test tests must be
concrete and masonry surfaces. conducted for Item 300 with a volume of 6,000
cubic meters?
A. Latex Paint
B. Enamel Paint A. 20
C. Read Lead B. 30
D. Oxide Paint C. 40
D. 50
36. Dial and Armored Stem Thermometer should
be inserted in the mixture to a minimum depth of 41. What is the load to produce 0.30mm crack
_____? with the following given data: The following are
A. 3” the data from the Three- Edge Bearing Test of
B. 5” Reinforced Concrete Pipe:
C. 6” Laying Length 1.0m
D. 10” Thickness of the wall = 125 mm
Actual Internal Diameter = 950 mm
37. For Thickness determination using core Load produce 0.30mm crack = 4250 lbs
asphalt, how many measurements should be taken Ultimate Load 4500 lbs
on its quarter points on the periphery? A. 19.90 N/m/mm
B. 199.0 N/m/mm
A. 9 C. 29.90 N/m/mm
B. 4 D. 299.0 N/m/mm
C. 5
D. 8 42. Embankment material has Plastic Limit of 34
and Liquid Limit of 30, what is the Plasticity
38. If the dry stability is 1,300 psi, wet stability of Index?
1,250 psi and air voids of 3%, what is the index of A. 64
retained strength (IRS)? B. 4
C. 88%
A. 104.0% D. 113%
B. 96.25%
C. 3.85% 43. Compute Fineness Modulus:
D. 96.15%
Sieve Size Percent Passing
39. Calculate the moisture content given the 3.8” 100
following data: No. 4 95
Original Weight = 150 grams No. 8 87
Oven Dried Weight = 145.50 grams No. 16 56
No. 30 35
No. 50 45
A. 3.90%
No. 100 4
B. 3.09%
No. 200 2
C. 3.00%
D. 3.19%
A. 2.68
B. 2.78
C. 3.76
D. 4.22

44. How many quality tests are required for each

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 4
type of paint if in a certain project, it requires 335 50. This test determines the right amount of
Gallons of paints, and which 160 gallons are Latex mixing water in compacting a soil fill to
paint, and the rest are enamel paint? obtain maximum density.
A. 2 Gal each
A. Consolidation
B. 3 Gal each
C. 4 Gal each
B. Compaction
D. 5 Gal each C. Dry Density
D. Atterberg Test
45. The application of coal tar asphalt sealer of a
surface treatment on an asphalt concrete pavement 51. What information is not provided on the
shall be from 21 to ____ degrees Celsius. sieving process?

A. 25 A. Soil Classification
B. 35 B. Distribution of Particle Size
C. 20
C. Shape of the Soil Grains
D. 40
D. Both A and B
46. What is standard height of Reflectorized
Thermoplastic Rubble Strips? 52. Unconfined compressive strength is used
for what type of soil?
A. 4-13 mm
B. 5-13 mm A. Sandy Soil
C. 3.2-4.8 mm B. Clayey Soil
D. 2.2-4.8 mm C. Silty Soil
D. Organic Soil
47. What is the roller speed when compacting the
newly laid bituminous mixture?
53. What is the minimum Plasticity Index for
A. 1-4 kph Aggregate Surface Course?
B. 5-10 kph
C. 6-7 kph A. 3
D. 8-10 kph B. 4
C. 5
48. What is the density of the rock fill for both D. 6
gabions and mattress?
54. How many layers will you compact and
A. 1,200 kg/m^3
what is the minimum compaction requirement
B. 1,300 kg/m^3
C. 1,400 kg/m^3
of embankment with a thickness of 1.2meters?
D. 1,500 kg/m^3
A. 6 layers with 95% compaction req.
49. What is the minimum cement content per cubic B. 8 layers with 95% compaction req.
meter of Shotcrete? C. 6 layers with 90% compaction req.
D. 8 layers with 90% compaction req.
A. 340
B. 350
C. 375
D. 325

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 5
55. What is the degree of compaction of soil if 59. This is an admixture that tends to reduce
the dry unit weight in the field is 1550 kg/m^3 incidence of thermal cracking and to maintain
and the laboratory dry maximum density is concrete workability during large pours or
1870 kg/m^3? long ready-mix hauls.

A. 82.99% A. Accelerator
B. 82.89% B. Superplasticizer
C. 120.65% C. Air-Entraining
D. 120.56% D. Retarders

56. What is the ratio of length to diameter of 60. The fiber shall also be hygroscopic with
the coconut coir fiber materials in fabrication moisture content of 10-12% at 65% humidity
of coconut geonets? and _____ at 95% relative humidity.

A. 25 A. 22-55%
B. 35 B. 32-55%
C. 30 C. 22-65%
D. 20 D. 32-65%

57. What is the maximum mass percent of 61. If the mean density of the control strip is
wear for Aggregate Surface Course? less than _____ of the density of laboratory
compacted specimen, take another control
A. 35 strip.
B. 45
C. 25 A. 98%
D. 30 B. 97%
C. 100%
58. A core was taken from a concrete pavement D. 95%
with a thickness of 30.9cm. What is the
corrected thickness to be used to get the 62. What do you call the selection by standard
average thickness if the design height is 30cm. method of a representative portion of a
material for ascertaining its characteristics?
A. 30.0 cm
B. 30.9cm A. sampling
C. 30.5cm B. testing
D. 29.10cm C. verification
D. validation

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 6
63. What kind of soil is used to perform 67. When hauled by Agitating Trucks, time
Consolidation Test? elapsed from the time water added to the mix
until the concrete is deposited in place shall not
A. Disturbed exceed?
B. Undisturbed
C. Silt & Clay A. 60 minutes
D. Colloids B. 45 Minutes
C. 75 Minutes
64. The rock asphalt as furnished shall contain D. 90 minutes
between ______ of Bitumen.
68. What is the ideal fineness modulus of well
A. 4-7% graded natural sand?
B. 3-12%
C. 5-8% A. 3.0
D. 8-13% B 2.25
C. 2.50
65. What is the recommended length of road D. 2.75
section where Reflectorized Rubble strips are
to be installed? 69. What is the standard unit weight per
meter of 32mm steel bars?
A. 10-20m
B. 20-30m A. 6.314 kg/m
C. 15-25m B. 4.834 kg/m
D. 15-30m C. 3.854 kg/n
D. 5.926 kg/m
66. What will you do when the aggregate
sample material such as base course passed the 70. When hauled by Non-Agitating Trucks,
requirements of quality tests except for time elapsed from the time water added to the
Grading? mix until the concrete is deposited in place
shall not exceed?
A. Obtain another set from a different source A. 60 minutes
B. Reject the material and the source B. 45 Minutes
C. Just accept the material and lessen the C. 75 Minutes
payment for the item D. 90 minutes
D. Process again the aggregate material by
blending 71. What is the maximum tolerance on the
mass of one piece of steel bar?

A. +-4.0%
B. +-5.0%
C. +-6.0%
D. +-10.0%

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 7
72. How high above the ground should the 77. What is the compressive strength of the 6"
chevron signs be installed in urban areas? diameter cylinder sample if it fails 450
kilonewton?
A. 2.20 m
B. 2.50 m A. 3,560 psi
C. 3.50 m B. 3,590 psi
D. 1.50 m C. 3,580 psi
D. 3,550 psi

73. What is the minimum flexural strength of 78. This is the wearing away of the concrete
beam sample when tested by Mid-Point pavement surface caused by the dislodging of
Method? aggregates particles and loss of binder.

A. 3.5 MPa A. Scaling

B. 4.5 MPa B. Shoving
C. 3.8 MPa C. Raveling
D. 4.8 MPa D. Rutting

74. What is the device that measures the 79. This test determines the crushing of
relative hardness of asphalt? strength of aggregates to ensure that coarse
aggregates will not degrade to smaller ones.
A. Pyrometer
B. Pycnometer A. Grading
C. Penetrometer B. Decantation
D. Viscometer C. Abrasion
D. CBR
75. What is the minimum uniform density of
crushed slag used for PCCP in kilogram/cubic 80. How many bags of cement per cubic meter
meter? of Class Seal Concrete?

A. 960 A. 9.1
B. 1,210 B. 11
C. 2,120 C. 9.5
D. 1,120 D. 8

76. If there are 555 pieces of reinforced pipe 81. What is the mixing time for concrete when
culverts, how many samples shall be taken for mixed in a central mixing plant?
testing? A. Less than 50 sec nor more than 90 sec
B. Less than 40 sec nor more than 90 sec
A. 6 C. Less than 50 sec nor more than 80 sec
B. 11 D. Less than 40 sec nor more than 80 sec
C. 13
D. 12

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 8
82. When transporting mixed concrete, the 86. For the installation of sheet pile, the joint
time elapsed from the time water added to the between the piles shall be practically _____
mix until the concrete is deposited in place within the piles are in place?
shall not exceed?
A. 60 minutes by Non-agitating trucks A. Welded
B. 45 minutes by agitating trucks B. Watertight
C. 45 minutes by Non-agitating trucks C. Galvanized
D. 90 minutes by Non-Agitating trucks D. Dirt Free

83. Fibers used in the manufacture of 87. Concrete in the area represented by the
geotextiles and the threads used in joining cores will be considered adequate in their
geotextiles by sewing shall consist of long- average strength is equal to:
chain synthetic polymers composed of at least
_____ percent by mass polyolefins, polyesters A. At least 85% and no single core is
or polyamides. less than 85% of the f'c
B. At least 75% and no single core is
A. 50% less than 75% of the f'c
B. 75% C. At least 85% and no single core is
C. 85% less than 75% of the f'c
D. 90% D. At least 75% and no single core is
84. The workability of the bituminous mixture less than 85% of the f'c
is very dependent on its _____.
88. The allowable temperature of asphalt mix
A. Compaction effort prior to spreading.
B. temperature of the mixture
C. shape and size of aggregates A. 105
D. Asphalt Content B. 107
C. 135
85. What is the maximum dimension of the D. 180
concrete slab used for Item 510 - Concrete
Slope Protection? 89. A road section with a length of 30km was
scheduled to paint thermoplastic pavement
A. 3mx3m marking on October 2015, this section is
B. 2mx2m located on a low speed, low volume road. When
C. 4mx4m shall be the next schedule of application of
D. 5mx5m thermoplastic marking?

A. October 2016
B. October 2017
C. October 2018
D. October 2019

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 9
90. The repeated operation of fine grading and 95. What is sieve no. that separates between
compacting the full width of the roadway to coarse and fine aggregates of Item 300,
undertaking any overlaying structural layer is Aggregate Surface Course?
____.

A. Subgrade Preparation A. No. 10

B. Embankment B. No. 8
C. Surface Course Preparation C. No. 4
D. Base Preparation D. No. 16

91. In laying stone components of Grouted 96. What is the minimum pull-offs per system
Riprap, each stone should be? or span of Carbon Fiber Sheets?

A. Laid with its longest axis

perpendicular to the slope A. 1
B. Laid with its longest axis parallel to B. 2
the slope C. 3
C. Pitch to line along the beds and joints D. 4
D. Laid with its face parallel to the face
of the walls 97. What is minimum sampling requirement
for Mineral Filler?
92. These are localized pavement surface areas
with slightly lower elevations than the A. 1.5 kg
surrounding pavement and are very noticeable B. 2.0 kg
after a rain when they fill with water. C. 2.5 kg
D. 3.0 kg
A. Depression
B. Pot Holes 98. How many CBR tests must be conducted
C. Scaling for Item 200 with a volume of 6, 000 cubic
D. Upheaval meters?
93. These are localized upward movement in a
pavement due to swelling of the subgrade. A. 2
B. 3
A. Depression C. 4
B. Pot Holes D. 5
C. Scaling
D. Upheaval 99. The total number of reflectorized
thermoplastic rubble strips of a certain project
94. In concrete surface it is defined as the loss is 134 bags; how many kilograms of samples
of surface mortar and mortar surrounding should be taken for testing?
the aggregate particles.
A. Depression A. 20
B. Pot Holes B. 2
C. Scaling C. 10
D. Upheaval D. 14

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 10
 BULK ORDERS FROM:

1. DPWH CDEO 2ND DEO

100. Reflective sheeting for Chevron Signs 2. DPWH MASBATE DEO
shall perform effectively for a minimum of 3. DPWH Regional Office XII
____ years from date of fabrication and retain 4. Stellavia Development Corporation
at least _____ of its original brightness. 5. Triplelee Development Corporation
6. Mechconic Corp
A. 6 years, 60% 7. Solid North Construction
B. 7 years, 70% 8. J316 Architectural Firm
C. 5 years, 50% 9. Zumiro Seido Engineering Services
D. 8 years, 80% 10. JFR Construction Inc.
11. SPES Construction
- END OF THE REFERSHER EXAM - 12. Goodman Builders Internationale
FACEBOOK PAGES: 13. MetroZambo Construction
We provide Manuals and Reviewers for Materials 14. Lonworks Technologies Inc
Engineer and Project Engineer and other Civil 15. JRJGB Construction and Trading Corp.
Engineering and Construction References since 2019 16. LG Construction
17. Alltek Engineering and Industrial Supplies
DPWH Materials & Project Engineer Manual & Reviewer
18. DM Phantoms Engineering Ser
https://www.facebook.com/DPWHPEreviewer
19. Magnarich Trading and Construction
20. J.J. Lacebal Construction and Development
21. Municipal Engineering office of Sta. Maria, Ilocos Sur
Civil Engineering & Other Construction References
22. BOSS Engineering
https://www.facebook.com/CivilEngineeringRefer
-at marami pang ibang 1 – 3 orders po -
ences
-Daghang Salamat sa pagsalig/TRUST!-
NOW AVAILABLE:
FIELD | SAFETY JACKETS ANSWERS:
1. A - 1:5 to 1:9
2. B - 4.5 to 8.5
3. C - 1.4 MPA (200 psi)
4. B - Quartering/Opposite S.
5. A - 3,720 psi
6. D - 4 QT
7. A - 2 Layers, 4.35m
8. D - G.I No. 160
9. A - 3mm
10. C - Sieve No. 10
11. A - 1-2 L/sqm
12. C - 150mm
13. A - 40-75 mm
14. A - 230 kN/mm2
15. C - 1.5 MPA

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 11
16. B - 10 Kn 48. C - 1,400 kg/m3
17. C - 1:3 49. D - 325kg/m3
18. C - 50m 50. B - Compaction
19. A – 4 51. C - Shape of the Soil grains
Bituminous Core = 4 Measurements 52. B - Clayey Soil
Concrete Core = 9 Measurements 53. B - 4
20. D - 3.0 m/km 54. A - 6 layers, 95% min
21. A - 20-50 psi/sec 55. B - 82.89%
22. A - Soundness Test 56. B - 35
23. A - 110+-5 Degrees 57. B - 45
24. C - Nuclear Density Gauge 58. C - 30.5 cm
25. A - Reclaimed Asphalt Pav. 59. D – Retarders
26. A - +-5% 60. A - 22-55%
27. D - 10mm 61. A - 98%
28. B - Discard the Mix 62. A - Sampling
29. A - Crate with saw Dust 63. B - Undisturbed Soil
30. A - Every 100 m 64. D - 8-13%
31. A - 3.785 L 65. B - 20-30 m
32. A - 211 +-7 Degrees 66. D - Blending
33. A - 1 set per 25 cubic meters 67. D - 90 Minutes
34. A - No. 18 68. D - 2.75
35. A - Latex Paint 69. A - 6.314 kg/m
36. C - 6" 70. B - 45 Minutes
37. B - 4 71. C - +-6%
38. D - 96.15% 72. A - 2.20m (Urban)
39. B - 3.09% 73. B - 4.5 MPA (Midpoint)
40. A - 20 Grading Tests 74. C - Penetrometer
41. A - 19.90 N/m/mm 75. D - 1,120 kg/m3 (PCCP)
42. B - 4 76. A - 6 Tests
43. B - 2.78 Update:
44. A - 2 Gal Old Specification: 1 for every 50 pieces
45. B - 35 Degrees New Specification: 1 for every 100 pieces
46. A - 4-13mm Alternative requirements: 1 set of 3 concrete
47. C - 6 -7 kph cylinder samples for not more than 25 pipes
For a vibratory roller capable of applying cast in the field + Inspection Report of
compactive effort at a rate of 3,600 vpm, the Casting (FOLLOW THE MPE MANUAL)
roller can be operated up to 4 mph or 6.45 77. C - 3,580 psi
kph. For a pneumatic-tire roller, the 78. B – Raveling
maximum speed should also be 4 mph. 79. C - Abrasion
Rollers can move faster or slower than the 80. C - 9.5 bags/m3
recommended speed, but compaction varies 81. A - 50 to 90 seconds
directly with roller speed. 82. C - 45 min, non-agitating

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 12
83. C - 85%
84. B - Temperature of the Mix
85. C - 4mx4m
86. B - Watertight
87. C - 85%min average, 75%
88. B - 107 Degrees
89. B - October 2017
90. A - Subgrade Preparation
91. A - Laid Perpendicular
92. A - Depression
93. Ꭰ - Upheaval
94. C - Scaling
95. A - Sieve No. 10 FACEBOOK PAGES:
96. B - 2 Pull Offs Minimum
We provide Manuals and Reviewers for Materials
97. C - 2.5 kG Engineer and Project Engineer and other Civil
98. B - 3 CBR Test Engineering and Construction References since 2019
99. A - 20 Kilogram DPWH Materials & Project Engineer Manual & Reviewer
A minimum weight of 10 kg of Reflectorized https://www.facebook.com/DPWHPEreviewer
Thermoplastic paint shall be taken for every
Civil Engineering & Other Construction References
100 bags or fraction thereof. https://www.facebook.com/CivilEngineeringRefer
100. B - 7years, 70% ences

ALSO AVAILABLE: DRY SEALS

TO AVAIL: JUST PM OUR FACEBOOK PAGE

For Contractors and Consultants looking for

Accredited ME1 & 2 and Project Engineers 1&2!
PM us your Location NOW! We will refer an
accredited ME/PE nearest to your location po!

We are ALSO looking for Accredited Materials

Engineer - 2 and Accredited Project Engineers 1 and
2 including provisional, PM this page with your
Name, FB Name and Location now!

Mark Lowill Banaag Almeda, RCE, ME-1, PPE

https://www.facebook.com/DPWHPEreviewer 13