ALUMINUM ELECTROLYTIC CAPACITORS

UD
Chip Type, Low Impedance

series

Chip type, low impedance temperature range up to +105°C.

Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine using carrier tape.
Adapted to the RoHS directive (2002/95/EC).
WD
High
Te m p reflow

CD Low Impedance UD Low Impedance WG

Specifications
Item Performance Characteristics
Category Temperature Range – 55 to +105°C
Rated Voltage Range 6.3 to 50V
Rated Capacitance Range 1 to 1500µF
Capacitance Tolerance ± 20% at 120Hz, 20°C
Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Measurement frequency : 120Hz, Temperature : 20°C
tan δ Rated voltage (V) 6.3 10 16 25 35 50
tan δ (MAX.) 0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14) ( ) is φ8 over

Measurement frequency : 120Hz

Rated voltage (V) 6.3 10 16 25 35 50
Stability at Low Temperature Z– 25°C / Z+20°C 3 2 2 2 2 2
Impedance ratio
ZT / Z20 (MAX.) Z– 55°C / Z+20°C 5 4 4 3 3 3

After 5000 hours' (2000 hours for φD 6.3) Capacitance change Within ±30% of initial value
application of rated voltage at 105°C , capacitors tan δ 200% or less of initial specified value
Endurance
meet the characteristic requirements listed at Leakage current Initial specified value or less
right.
After storing the capacitors under no load at 105°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4
Shelf Life
clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above.
The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value
Resistance to soldering for 30 seconds. After removing from the hot plate and restored
tan δ Initial specified value or less
heat at room temperature, they meet the characteristic requirements
Leakage current Initial specified value or less
listed at right.
Marking Black print on the case top.

Chip Type Type numbering system (Example : 16V 22µF)

(φ4 to 6.3)
Positive 1 2 3 4 5 6 7 8 9 10 11 12 13 14
0.5 MAX.

Plastic platform
0.3 MAX. C±0.2
UUD 1 C 2 2 0 M C L 1 GS
Voltage (C:16V) Series
A±0.2

Package code
φD±0.5
22C

B±0.2

Configuration
UD
N2

A±0.2

Capacitance tolerance (±20%)φD Code

4 to 6.3 CL
L±0.3 Rated Capacitance (22µF)
Lot No. Capacitance Negative 8 • 10 NL
H Rated voltage (16V)
Series name
Type
(φ8×10, φ10×10 )
Positive
0.5 MAX.

Plastic platform
Voltage (V:35V) 0.3 MAX. C±0.2 (mm)
Series
Trade mark φD×L 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 10 × 10
A±0.2 A±0.2

A 1.8 2.1 2.4 2.4 2.9 3.2

100V

φD±0.5

B 4.3 5.3 6.6 6.6 8.3 10.3

B±0.2
UD

E
N2

C 4.3 5.3 6.6 6.6 8.3 10.3

E 1.0 1.3 2.2 2.2 3.1 4.5
L 5.8 5.8 5.8 7.7 10 10
Lot No. Capacitance L±0.5 Negative H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Pressure relief vent H

Voltage
V 6.3 10 16 25 35 50
Code j A C E V H

Dimension table in next page. CAT.8100W

ALUMINUM ELECTROLYTIC CAPACITORS

UD series

Dimensions
V 6.3 10 16 25 35 50
Cap.
(µF) Code 0J 1A 1C 1E 1V 1H
1 010 4 × 5.8 5.00 30
2.2 2R2 4 × 5.8 5.00 30
3.3 3R3 4 × 5.8 5.00 30
4.7 4R7 4 × 5.8 1.80 80 5 × 5.8 1.52 85
10 100 4 × 5.8 1.80 80 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
15 150 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
22 220 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.88 165
27 270 4 × 5.8 1.80 80 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
33 330 5 × 5.8 0.76 150 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
47 470 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.68 185
56 560 5 × 5.8 0.76 150 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300
68 680 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.34 300
100 101 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.34 300
150 151 6.3 × 5.8 0.44 230 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.18 670
220 221 6.3 × 5.8 0.44 230 6.3 × 7.7 0.34 280 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.18 670
330 331 6.3 × 7.7 0.34 280 8 × 10 0.17 450 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670
470 471 8 × 10 0.17 450 8 × 10 0.17 450 8 × 10 0.17 450 10 × 10 0.09 670
680 681 8 × 10 0.17 450 10 × 10 0.09 670 10 × 10 0.09 670
1000 102 8 × 10 0.17 450 10 × 10 0.09 670 Case size Rated
Impedance
φ D × L (mm)
1500 152 10 × 10 0.09 670 ripple

Max. Impedance (Ω) at 20°C 100kHz,

Rated Ripple (mArms) at 105°C 100kHz

Frequency coefficient of rated ripple current

Frequency 50 Hz 120 Hz 300 Hz 1 kHz 10 kHz or more
Coefficient 0.35 0.50 0.64 0.83 1.00

Taping specifications are given in page 23.

Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.

CAT.8100W