Datasheet: uni NTB C
EN
Plastic Modular Belt
Serie uni NTB Type C
Straight Running Belt
Nominal pitch: 8.0 mm (0.32 in)
Surface type: Flat
P Surface opening: Closed
STANDARD
T Backflex radius: R6 mm (0.24 in)
L
on
Pin diameter: 3.0 mm (0.12 in)
ti
ec
dir
ing
nn
Ru
Belt material mm in mm in
& color POM-D B
P 8.0 0.32 T 6.00 0.24
(Nominal)
Pin material
& color PA6.6 B
L 3.00 0.12 - - -
STRAIGHT RUNNING
Non standard material and color: See uni Material and Color Overview.
Alternative pin and lock materials: PBT LG
Permissible tensile force Belt weight Number of wear
(Belt/pin material) (Belt/pin material) strips (min no)
Belt width *
Min No
drive sprocket
POM-D/PA6.6 POM-D/PA6.6 per shaft Carry
** **
Return
(pcs) (pcs)
mm in N lbf Kg/m Ib/ft
76 3.0 167 38 0.4 0.24 2 2 2
153 6.0 337 76 0.7 0.49 2 2 2
229 9.0 504 113 1.1 0.73 3 3 2
305 12.0 671 151 1.5 0.98 4 4 2
PITCH 8.0 MM/0.32 IN
381 15.0 838 188 1.8 1.22 4 4 2
458 18.0 1008 227 2.2 1.47 5 5 3
534 21.0 1175 264 2.5 1.71 6 6 3
610 24.0 1342 302 2.9 1.95 7 7 4
686 27.0 1509 339 3.3 2.19 7 7 4
762 30.0 1676 377 3.6 2.44 8 8 4
839 33.0 1846 415 4.0 2.68 9 9 5
915 36.0 2013 453 4.4 2.93 10 10 5
991 39.0 2180 490 4.7 3.17 10 10 5
Additional standard belt widths are available in steps of 76.2 mm (3.00 in). Additional non-standard belt widths are available in steps of 25.4 mm (1.00 in).
1448 57.0 3186 716 6.9 4.63 15 15 8
Additional standard belt widths are available in steps of 76.2 mm (3.00 in). Additional non-standard belt widths are available in steps of 25.4 mm (1.00 in).
1982 78.0 4360 980 9.4 6.34 20 20 10
General belt tolerance is +0/-0.4% at 23°C/73°F and 50% RH. For exact belt width contact Customer Service. Non standard belt width on request.
*Max. Load per Drive Sprocket. Belt material: POM-D 200N (44 lbf).
**Max. Spacing between wear strips, Carry: 102.0 mm (4.00 in); Return: 203.0 mm (8.00 in).
= Single Link
Datasheet: uni NTB C
Sprocket
Double row/Two way
Single row/Two way
Dimension
Dimension
PA6 LG
Bore size
diameter
diameter
diameter
PA6 N
Overall
Pitch
Hub
No. of teeth
B
0.75
0.78
0.98
1.00
1.18
1.25
1.50
1.57
in
Pilot bore
Machined
Molded
19.1
20.0
25.0
25.4
30.0
31.8
38.1
40.0
mm
mm in mm in mm in mm in mm in
Z24 x 61.3 2.41 61.3 2.41 57.3 2.26 27.38 1.08 33.65 1.32 x x
Z32 x 81.6 3.21 81.7 3.21 77.6 3.06 37.61 1-48 43.8 1.72 x x
Z48 x 122.7 4.83 122.4 4.81 118.7 4.67 58.03 2.28 64.16 2.52 x x
Z60 x 152.9 6.02 152.9 6.02 148.9 5.86 73.32 2.88 79.43 3.13 x x
Non standard material and
Machined sprocket Machined sprocket color: See uni Material and
Color Overview.
Nosebars Min. Dimensions
B
C mm in
D C 20.0 0.79
A
D 6.0 0.24
E
E 2.0 0.08
Other sprocket sizes are available upon request.
Round bores are always delivered with keyway.
Other bore sizes are available upon request.
uni Retainer Rings: See uni Retainer Ring data sheet.
Width of tooth = 9.0 mm (0.35 in)
Width of sprocket = 25.0 mm (0.98 in)
Max load per sprocket shown does not take bore size into account.
Please also ensure that sufficient size shaft is chosen for corresponding load.
For correct sprocket position: See uni Assembly Instructions for uni NTB.
For more detailed sprocket information, contact Customer Service.
uni NTB C/170522
Expert advice, quality solutions Ammeraal Beltech Modular A/S
Transmission Belts
Conveyor Belts
Seamless Belts
and local service Hjulmagervej 21
Modular Belts
Timing Belts
Fabrication
for all your belting needs DK-7100 Vejle
& service
www.ammeraalbeltech.com
T +45 7572 3100
This information is subject to alteration due to continuous development. Ammeraal Beltech will not be held liable for the incorrect F +45 7572 3348
use of the above stated information. This information replaces previous information. All activities performed and services rendered by [email protected]
Ammeraal Beltech are subject to general terms and conditions of sale and delivery, as applied by its operating companies. www.unichains.com
