Product Introduction
MX370104A
Multi-carrier IQproducerTM
MG3700A
Vector Signal Generator
For MG3700A Vector Signal Generator
MX370104A
Multi-carrier IQproducerTM
Product Introduction
Version 3.00
ANRITSU CORPORATION
Slide 1
MX370104A-E-I-1
Ordering information
Model/Order Name Remarks
No.
— Mainframe —
MG3700A Vector Signal Generator Required
— Options —
MG3700A-002 Mechanical Attenuator Standard Electron Attenuator is
changed into Mechanical Attenuator.
MG3700A-011 Upper Frequency 6 GHz Standard “250 kHz to 3 GHz” is
extended to “250 kHz to 6 GHz.”
MG3700A-021 ARB Memory Upgrade 512 M Standard “128 Msample/channel × 2” is
Recomme
sample extended to “256 Msample/channel ×
ndation
2.”
Standard “1 kbps to 20 Mbps” is
MG3700A-031 High Speed BER Test Function
extended to “100 bps to 120 Mbps.”
— Softwares (License Key for IQproducer system) —
MX370104A Multi-carrier IQproducer Required
— Optional accessories —
W2495AE MG3700A operation manual Booklet
W2496AE MG3700A IQproducer operation
Booklet
manual
Recomme The PDF manual is on the software CD. Order this
W2539AE MG3700A standard waveform
Booklet ndation when a booklet is required.
pattern operation manual
W2633AE MX370104A Multi-carrier
Booklet
IQproducer operation manual
Recomme Required when PC connected directly to MG3700A
J1261D Ethernet Cable (Shield Type) Cross, 3 m
ndation by LAN.
Standard waveform pattern DVD set of pre-install wave form pattern
Z0777
upgrade kit of latest version
Exchange HDD when built-in HDD
G0141 HDD ASSY
break.
Cable that converts IQ output connector Recomme Converts IQ output connector on back of MG3700A
J1277 IQ Output Conversion Adapter
(D-sub) of mainframe into BNC ndation from D-sub to BNC.
Slide 2
MX370104A-E-I-1
What is Multi-carrier IQproducer?
MX370104A is PC software that can generate waveform patterns of the multi career
that uses the modulation signal of various communication systems and the tone
signal.
Parameters are set freely with the MX370104A software installed in a PC and the waveform
patterns of 32 careers(maximum) are generated. The generated waveform pattern can be
transferred to the mainframe of MG3700A via a CF card or a LAN, and the MG3700A
mainframe can output the desired signal by selecting a waveform pattern.
MG3700A
PC CF Card Vector Signal Generator
IQproducer
100Base-TX LAN
MX370104A
(2) Waveform data (3) Waveform (4) Signal license key*
(1) IQproducer data transferred
generated using output required
installed in PC to MG3700A
IQproducer
*Install the license key file in the main frame when adding a system license to a shipped
unit. The MG3700A main frame does not require return to the factory.
Slide 3
MX370104A-E-I-1
What is Multi-carrier IQproducer?
MX370104A Multi-carrier IQproducer is PC software to create multi career waveform
patterns of modulation signal of various telecommunication systems.
[Multi-purpose function]
- Waveform that uses tone signals and waveform pattern of various telecommunication systems
- Waveform that mixed two different telecommunication systems or more
- Waveform with offset that exceeds frequency offset range of two signal combine function of MG3700A
[Adjust Rate function]
- Waveform that converts Sampling Rate of two wavy patterns of different telecommunication system into
the same value <Two waveforms of a different telecommunication system is output by "Two signal
combine function" of MG3700A. >
[W-CDMA (DL) function]
Multi career waveform to which clipping is set. For the evaluation of the base station transmission
amplifier of W-CDMA.
- Generating waveform patterns using MX3701xxA => The main frame requires a license.
The unlicensed software will run on the PC to test waveform pattern generation but an unlicensed MG3700A cannot
output signals because it does not recognize the waveform patterns.
- Generating waveform patterns using EDA Tools (C, MATLAB, Microwave Office) => Free license
Slide 4
MX370104A-E-I-1
What is Multi-carrier IQproducer?
[Multi-purpose function]
The Multi-purpose function performs multi-carrier conversion of existing waveform patterns and
tone signals using the MG3700A. Using this function, a signal with up to 32 carriers can be
converted to a single waveform pattern. (Sometimes it is not possible to set as many as 32
carriers depending on the combination of the frequency offset and waveform pattern. On the
other hand, it is possible to create waveform patterns with more than 32 carriers by selecting
waveform patterns already created previously using this function.)
Example) Multi career signal of "FWD and RVS" of CDMA2000
Multi-carrier setting screen Multi-carrier FFT screen
Slide 5
MX370104A-E-I-1
What is Multi-carrier IQproducer?
[Adjust Rate function]
The Adjust Rate function converts two waveform patterns with different sampling rates into two
waveforms patterns with the same sampling rate.
With the MG3700A two-signal combining function, combining waveform patterns with different
sampling rates causes the bandwidth to change because the waveform pattern in memory B is
output at the sampling rate of the waveform pattern in memory A. Using the Adjust Rate
function, it is possible to combine the Wanted Signal and Interference Signal for various
communication systems with the same sampling rate. By matching the sampling rates of the two
waveform patterns using this function, it is even possible to output a signal for different
communication systems by using the Two Signals Combining function.
Example) The sampling rate of "WLAN and Bluetooth" is adjusted.
Bluetooth_Interferer
WLAN_Interferer
Multi-carrier setting screen Spectrum analysis screen
Slide 6
MX370104A-E-I-1
What is Multi-carrier IQproducer?
[W-CDMA (DL) function]
This function is used to create a waveform pattern by setting any of the 4 or 5 carriers of the W-
CDMA Downlink ON/OFF, as well as by setting the Clipping Method, Clipping Reference Level,
and Clipping Ratio.
(Example) W-CDMA clipping and multi-carrier
- Carrier Type:
Test Model 1 16DPCH, Test Model 5 2HS-PDSCH
Test Model 1 32DPCH, Test Model 5 4HS-PDSCH
Test Model 1 64DPCH, Test Model 5 8HS-PDSCH
- Clipping Method:
None
Vector (pre-filter)
Vector (post-filter)
Scalar (pre-filter)
Scalar (post-filter)
-Clipping Reference:
Peak Power
RMS Power
Multi-Carrier setting screen
Slide 7
MX370104A-E-I-1
Operation Images
Setup Slide 9
Starting IQproducer Slide 10
IQproducer Main Screen Slide 10
Editing Parameters Slide 11–16
Generating Waveform Slide 17
Transferring Waveform Pattern Slide 18-19
Saving/Recalling Parameters Slide 20
Slide 8
MX370104A-E-I-1
Setup
Connect the MG3700A and PC as shown below.
Install IQproducer in the PC.
Install the MX370104A license key in the MG3700A.
IQproducer MG3700A Vector Signal Generator
+ MX370104A License key
100Base-TX LAN
Crossover cable
IQproducerTM operating environment
CPU Pentium III, 1GHz or faster
* Refer to the appendix [IQproducer Upgrade
Memory size 512 Mbytes or more Procedure] for the installation method of
HDD 5 Gbytes or more IQproducer.
Display 1024 x 768 pixels or more * Refer to the appendix [Connection to LAN]
OS Windows2000 Professional, for the LAN connection between a PC and the
MG3700A.
Windows XP
Slide 9
MX370104A-E-I-1
Starting IQproducer
Start IQproducer as follows:
Start > Program > Anritsu Corporation > IQproducer for MG3700A
IQproducer Main Screen
When IQproducer starts, the following screen is displayed.
Choose Multi-Carrier from the [System] pull-down menu.
Slide 10
MX370104A-E-I-1
Editing Parameters: Main screen
When Multi-carrier is selected with System, the main screen where three functions
of Multi-purpose, Adjust Rate, and W-CDMA(DL) are chosen is displayed.
Each parameter can be set from the screen by selecting either of function.
Either of three functions
is selected (click).
- Multi-carrier
- Adjust Rate
- W-CDMA (DL)
Slide 11
MX370104A-E-I-1
Editing Parameters: Multi-purpose (1/2)
First, perform settings for the Tone or wvi File parameters for each component.
Check the corresponding Tone checkbox to select Tone.
Next, parameters of Gain, Freq. Offset, Delay, and Phase are set.
Gain:
0.00 to - 80.00 dB,
resolution:0.01 dB
Freq.Offset:
-0.4 x Fs + 0.5 x BW
to 0.4 x Fs - 0.5 x BW
(Fs : sampling frequency)
(BW: all band)
Delay: 0 to N-1
(N: Data Points of the source wvi file)
Phase:
0 to 359 degree,
resolution: 1 degree
Next page Tone, wvi File: Perform settings for the Tone or wvi File parameters.
Slide 12
MX370104A-E-I-1
Editing Parameters: Multi-purpose (2/2)
The Multi-tone function generates Tone signals at the specified frequency interval.
This function is enabled when a component is selected to set the specified number
of Tone signals starting from the selected component No. If a wvi file is already
selected for the corresponding component, then the setting is replaced by the Tone
signal setting.
Carrier Spacing:
0.000001 to 120 MHz
resolution: 1 Hz
Carrier Number:
1 to 32
(The number of Tone signals that
can be set varies depending on the
set value for Carrier Spacing.)
Power step:
0.00 to - 80.00 dB
Slide 13
MX370104A-E-I-1
Editing Parameters: Adjust Rate
Parameters of wvi. File, Phase, and Delay are set.
wvi File:
Waveform pattern used by two
wave combine function is
selected.
Delay:
0 to N-1
(N: Data Points of the source wvi file)
Phase:
0 to 359 degree,
resolution: 1 degree
[Note] Depending on to the
combination of the wvi file set in
Component 1, 2 and setting values
of Over Sampling, it might take
several ten minutes to several hours
at calculation time.
Slide 14
MX370104A-E-I-1
Editing Parameters: W-CDMA (DL) (1/2)
Following parameters are set.
Level setting
Carrier Type
Clipping Method
Clipping
Reference Clipping Index
Slide 15
MX370104A-E-I-1
Editing Parameters: W-CDMA (DL) (2/2)
Details on W-CDMA (DL) parameters
Item Outlone Setting range
Carrier allocation selection Select the carrier allocation. Selected/not selected
Carrier selection Select the carrier to be output. Check the checkbox to Enabled/disabled
enable the corresponding carrier.
Level setting Set the level for each carrier. This can only be set for 0.00 to –80.00 dB,
the enabled carriers. resolution: 0.01 dB
Frequency offset setting Set the frequency offset for each carrier using the step Frequency offset for each carrier ±1.0 MHz,
keys. This can only be set for the enabled carriers. resolution:0.1 MHz
Carrier Type selection Select the W-CDMA test model. Test Model1 16DPCH, Test Model1 32DPCH,
Test Model1 64DPCH, Test Model5 2HS-PDSCH,
Test Model5 4HS-PDSCH,
Test Model5 8HS-PDSCH
Clipping Method selection Select the clipping method for the clipping function. Non,
Vector(pre-filter),
Vector(post-filter),
Scalar(pre-filter),
Scalar(post-filter)
Clipping Reference selection Set the reference value of the clipping ratio for each Peak Power,
carrier. RMS Power
Clipping Index setting When Peak Power is selected, set the ratio to the 0 to 100%, resolution: 1% (When Clipping
maximum peak of the waveform being used in % units. Reference is set to Peak Power:)
When RMS Power is selected, set the ratio to the RMS 0.00 to 17.00 dB, resolution: 0.05 dB (When Clipping
Power of the waveform being used in dB unit. Reference is set to RMS Power)
Slide 16
MX370104A-E-I-1
Generating Waveform: Calculation
Click the [Calculation] icon to start creation of the waveform pattern after setting the
parameters.
(1)
(2)
(3)
(4)
(1) File export destination folder
(2) Name of waveform pattern package
(31 characters max.)
(3) Name of waveform pattern file
(20 characters max.)
(4) Comment on screen
OK: Creates waveform pattern (38 characters max. per line)
Slide 17
MX370104A-E-I-1
Transferring Waveform Pattern
Connect the MG3700A and PC via a LAN.
Transfer & Setting Transfer & Setting
Wizard Wizard
Input name or IP address of
MG3700A.
Connects to LAN
*Read the appended [LAN Connection] for the LAN
connection method between the PC and MG3700A.
Slide 18
MX370104A-E-I-1
Transferring Waveform Pattern
Select waveform
pattern saved on
MG3700A HDD.
Select when loading
waveform pattern into
memory at same time
as transferring.
Starts transfer
Slide 19
MX370104A-E-I-1
Saving/Recalling Parameters
The numerical value and the setting of each item can be saved as a parameter file,
and can be recalled.
Recall
Save
Recall
Save
File save screen File recall screen
Slide 20
MX370104A-E-I-1
Specifications are subject to change without notice.
• United States • Italy • Singapore
Anritsu Company Anritsu S.r.l. Anritsu Pte. Ltd.
1155 East Collins Blvd., Suite 100, Richardson, Via Elio Vittorini 129, 00144 Roma, Italy 60 Alexandra Terrace, #02-08, The Comtech (Lobby A)
TX 75081, U.S.A. Phone: +39-6-509-9711 Singapore 118502
Toll Free: 1-800-267-4878 Fax: +39-6-502-2425 Phone: +65-6282-2400
Phone: +1-972-644-1777 Fax: +65-6282-2533
Fax: +1-972-671-1877 • Sweden
Anritsu AB • P.R. China (Shanghai)
• Canada Borgarfjordsgatan 13A, 164 40 KISTA, Sweden Anritsu (China) Co., Ltd.
Anritsu Electronics Ltd. Phone: +46-8-534-707-00 Room 1715, Tower A CITY CENTER of Shanghai,
700 Silver Seven Road, Suite 120, Kanata, Fax: +46-8-534-707-30 No.100 Zunyi Road, Chang Ning District,
Ontario K2V 1C3, Canada Shanghai 200051, P.R. China
Phone: +1-613-591-2003 • Finland Phone: +86-21-6237-0898
Fax: +1-613-591-1006 Anritsu AB Fax: +86-21-6237-0899
Teknobulevardi 3-5, FI-01530 VANTAA, Finland
• Brazil Phone: +358-20-741-8100 • P.R. China (Hong Kong)
Anritsu Eletrônica Ltda. Fax: +358-20-741-8111 Anritsu Company Ltd.
Praça Amadeu Amaral, 27 - 1 Andar Unit 1006-7, 10/F., Greenfield Tower, Concordia Plaza,
01327-010 - Bela Vista - São Paulo - SP - Brazil • Denmark No. 1 Science Museum Road, Tsim Sha Tsui East,
Phone: +55-11-3283-2511 Anritsu A/S (Service Assurance) Kowloon, Hong Kong, P.R. China
Fax: +55-11-3288-6940 Anritsu AB (Test & Measurement) Phone: +852-2301-4980
Fax: +852-2301-3545
• Mexico Kay Fiskers Plads 9, 2300 Copenhagen S, Denmark
Anritsu Company, S.A. de C.V.
Phone: +45-7211-2200
Fax: +45-7211-2210 • Japan
Av. Ejército Nacional No. 579 Piso 9, Col. Granada Anritsu Corporation
11520 México, D.F., México • Russia 8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016 Japan
Phone: +52-55-1101-2370 Anritsu EMEA Ltd. Phone: +81-46-296-1221
Fax: +52-55-5254-3147 Fax: +81-46-296-1238
Representation Office in Russia
• United Kingdom Tverskaya str. 16/2, bld. 1, 7th floor.
Russia, 125009, Moscow
• Korea
Anritsu EMEA Ltd. Anritsu Corporation, Ltd.
Phone: +7-495-363-1694
200 Capability Green, Luton, Bedfordshire, LU1 3LU, U.K. 502, 5FL H-Square N B/D, 681
Fax: +7-495-935-8962
Phone: +44-1582-433200 Sampyeong-dong, Bundang-gu, Seongnam-si,
Fax: +44-1582-731303 • United Arab Emirates Gyeonggi-do, 463-400 Korea
Phone: +82-31-696-7750
• France Anritsu EMEA Ltd. Fax: +82-31-696-7751
Anritsu S.A. Dubai Liaison Office
12 avenue du Québec, Bâtiment Iris 1- Silic 612, P O Box 500413 - Dubai Internet City • Australia
91140 VILLEBON SUR YVETTE, France Al Thuraya Building, Tower 1, Suit 701, 7th Floor Anritsu Pty. Ltd.
Phone: +33-1-60-92-15-50 Dubai, United Arab Emirates Unit 21/270 Ferntree Gully Road, Notting Hill,
Fax: +33-1-64-46-10-65 Phone: +971-4-3670352 Victoria 3168, Australia
Fax: +971-4-3688460 Phone: +61-3-9558-8177
• Germany Fax: +61-3-9558-8255
Anritsu GmbH • India
Nemetschek Haus, Konrad-Zuse-Platz 1 Anritsu India Private Limited • Taiwan
81829 München, Germany 2nd & 3rd Floor, #837/1, Binnamangla 1st Stage, Anritsu Company Inc.
Phone: +49-89-442308-0 Indiranagar, 100ft Road, Bangalore - 560038, India 7F, No. 316, Sec. 1, NeiHu Rd., Taipei 114, Taiwan
Fax: +49-89-442308-55 Phone: +91-80-4058-1300 Phone: +886-2-8751-1816
Fax: +91-80-4058-1301 Fax: +886-2-8751-1817
1209
Please Contact:
Printed on Recycled Paper
No. MX370104A-E-I-1-(3.00) Printed in Japan 2012-11 MG
