Data Sheet

Vector Signal Generator

MG3710E
100 kHz to 2.7 GHz
100 kHz to 4.0 GHz
100 kHz to 6.0 GHz
 Contents

Definitions, Conditions of Specifications....................................................................................................................................... 3

Frequency........................................................................................................................................................................................... 4

Output Level...................................................................................................................................................................................... 5

ATT Hold Function............................................................................................................................................................................ 9

Output Connector............................................................................................................................................................................. 9

Maximum Reverse Input Power...................................................................................................................................................... 9

Signal Purity....................................................................................................................................................................................... 9

Analog Modulation......................................................................................................................................................................... 16

Vector Modulation.......................................................................................................................................................................... 18

Arbitrary Waveform Generator..................................................................................................................................................... 25

AWGN Generation Function........................................................................................................................................................... 26

Sweep/List Function........................................................................................................................................................................ 26

BER Measurement Function........................................................................................................................................................... 27

Connector......................................................................................................................................................................................... 28

Display.............................................................................................................................................................................................. 29

General............................................................................................................................................................................................. 29

2
Definitions
Typical (typ.)
Performance not warranted. Must products meet typical performance.
Nominal (nom.)
Values not warranted. Included to facilitate application of product.
Measured (meas)
Performance not warranted. Data actually measured by randomly selected measuring instruments.

Conditions of Specifications
The conditions are as follows unless specified otherwise.

CW/Modulation Mode
After 30 -minute warm-up (at constant ambient temperature)
Pulse Modulation: Off
ATT Hold: Off
Optimize S/N Mode: Off
*: f > 2 .7 GHz: Use MG 3710 E-034 /036 , MG3710 E-064 /066
f > 4 GHz: Use MG3710 E-036 , MG3710 E-066

Modulation Mode only

Waveform pattern RMS value: At RMSw (Linear value) and each combination less than following ranges:
–3 .00 dB ≤ RMSnom ≤ + 3 .00 dB
RMSnom = 20 log (RMSw/4628 ) (16 bit Data)
RMSnom = 20 log (RMSw/2314 ) (15 bit Data)
RMSnom = 20 log (RMSw/1157 ) (14 bit Data)

after CAL

*: Applies to MG3710 E-062 /064 /066

3
 Frequency

Setting Range
1 st SG
9 kHz to 2 .7 GHz [MG3710 E-032 ]
9 kHz to 4 GHz [MG3710 E-034 ]
9 kHz to 6 GHz [MG3710 E-036 ]
2 nd SG
9 kHz to 2 .7 GHz [MG3710 E-062 ]
9 kHz to 4 GHz [MG3710 E-064 ]
9 kHz to 6 GHz [MG3710 E-066 ]
Resolution: 0 .01 Hz

Phase Offset
Range: –180 .00 deg. to +180 .00 deg.
Resolution: 0 .01 deg.

Switching Speed
≤ 600 µs
(Frequency: >187 .5 MHz, Phase Noise Optimization: offset < 200 kHz, Time from trigger input to final frequency ±0 .1 ppm or within 100 Hz
when executing List function.)

Internal Reference Oscillator

without MG3710 E-001 /002
Aging rate: ±1 × 10 –6 /year
Temperature characteristics: ±2 .5 × 10 –6 (5 °C to 45 °C)
with MG3710 E-001
Start-up characteristics: 2
 3 °C, Referenced to frequency at 24 hours after power-on
± 1 × 10 –9 (7 .5 minutes after power-on)
Aging rate: ±1 × 10 –10 /month
Temperature characteristics: ±2 × 10 –9 (5 °C to 45 °C)
with MG3710 E-002
Start-up characteristics: 2
 3 °C, Referenced to frequency at 24 hours after power-on
± 5 × 10 –7 (2 minutes after power-on)
± 5 × 10 –8 (5 minutes after power-on)
Aging rate: ±1 × 10 /year
–7

Temperature characteristics: ±2 × 10 –8 (5 °C to 45 °C)

4
Output Level

Setting Range
without MG3710 E-043 /073
–110 to +17 dBm [without MG3710 E-041 /042 ], [without MG3710 E-071 /072 ]
–110 to +30 dBm [with MG3710 E-041 , without MG3710 E-042 ], [with MG3710 E-071 , without MG3710 E-072 ]
–144 to +17 dBm [without MG3710 E-041 , with MG3710 E-042 ], [without MG3710 E-071 , with MG3710 E-072 ]
–144 to +30 dBm [with MG3710 E-041 /042 ], [with MG3710 E-071 /072 ]
with MG3710 E-043 /073
–110 to +17 dBm [without MG3710 E-041 /042 ], [without MG3710 E-071 /072 ]
–110 to +25 dBm [with MG3710 E-041 , without MG3710 E-042 ], [with MG3710 E-071 , without MG3710 E-072 ]
–144 to +17 dBm [without MG3710 E-041 , with MG3710 E-042 ], [without MG3710 E-071 , with MG3710 E-072 ]
–144 to +25 dBm [with MG3710 E-041 /042 ], [with MG3710 E-071 /072 ]

(meas)

Unit
dBm, dBµV (Terminated, Open)

Resolution
0 .01 dB

Switching Speed
≤ 600 µs
(When frequency is >187 .5 MHz within output level accuracy specification range)
However, the output level is ≤+7 dBm when neither the MG3710 E-041 nor MG3710 E-071 is installed.
This is defined as the period from detection of the List function execution trigger until the time when the frequency is within ±0 .2 dB of the
final output level.

5
 Level Accuracy
18 °C to 28 °C, CW
without Reverse Power Protection [without MG3710 E-043 ], [without MG3710 E-073 ]

High Power Extension

Low Power Extension
MG3710E-042/072

MG3710E-041/071
Frequency Range

>–100 dBm

≤–100 dBm
>–110 dBm

≤–110 dBm
>–120 dBm

≤–120 dBm
>–127 dBm

≤–127 dBm
>–136 dBm
≤+23 dBm
>+20 dBm

≤+20 dBm
>+13 dBm

≤+13 dBm
>+11 dBm

≤+11 dBm
>+10 dBm

≤+10 dBm
>+5 dBm

≤+5 dBm
without without — — — —
without with — — — — — ±0.5 dB —
100 kHz ≤ f < 1 MHz
with without — — — (typ.) — — — —
with with — — — — — — — — —
without without — — —
without with — — — — —
1 MHz ≤ f < 10 MHz ±0.5 dB (typ.)
with without — — — ±0.5 dB — —
with with — — — — — (typ.) — —
without without — —
without with — — — — ±0.7 dB
10 MHz ≤ f < 50 MHz ±0.5 dB (typ.)
with without — — (typ.) ±0.5 dB — —
with with — — — — (typ.) — —
without without
without with — ±0.6 dB
50 MHz ≤ f < 400 MHz ±0.5 dB
with without ±1.5 dB
±0.5 dB ±0.7 dB
with with — ±0.6 dB (typ.)
without without
without with ±0.6 dB
400 MHz ≤ f ≤ 3 GHz ±0.5 dB
with without ±1.5 dB
±0.5 dB ±0.7 dB
with with ±0.6 dB (typ.)
without without
without with — ±0.7 dB
3 GHz < f ≤ 4 GHz ±0.7 dB
with without ±2.5 dB —
±0.7 dB
with with — ±0.7 dB (typ.) —
without without
without with — —
4 GHz < f ≤ 5 GHz ±0.8 dB
with without ±2.5 dB —
±1.0 dB
with with — — (typ.) —
without without —
without with — — —
5 GHz < f ≤ 6 GHz ±0.8 dB
with without — ±2.5 dB —
±1.0 dB
with with — — — (typ.) —

with Reverse Power Protection [with MG3710 E-043 ], [with MG3710 E-073 ]
High Power Extension
Low Power Extension
MG3710E-042/072

MG3710E-041/071

Frequency Range
>–100 dBm

≤–100 dBm
>–110 dBm

≤–110 dBm
>–120 dBm

≤–120 dBm
>–127 dBm

≤–127 dBm
>–136 dBm
≤+20 dBm
>+17 dBm

≤+17 dBm
>+10 dBm

≤+10 dBm
>+8 dBm

≤+8 dBm
>+7 dBm

≤+7 dBm
>+2 dBm

≤+2 dBm
>–2 dBm

≤–2 dBm

without without — — — —
without with — — — — — —
100 kHz ≤ f < 1 MHz ±0.5 dB (typ.)
with without — — — — — — —
with with — — — — — — — — —
without without — — —
without with — — — — —
1 MHz ≤ f < 10 MHz ±0.5 dB (typ.)
with without — — — ±0.5 dB — —
with with — — — — — (typ.) — —
without without — —
without with — — — — ±0.7 dB
10 MHz ≤ f < 50 MHz ±0.5 dB (typ.)
with without — — (typ.) ±0.5 dB — —
with with — — — — (typ.) — —
without without ±0.5 dB
without with — ±0.6 dB ±0.5 dB
50 MHz ≤ f < 400 MHz
with without ±0.5 dB ±1.5 dB
±0.7 dB
with with — ±0.6 dB ±0.6 dB ±0.5 dB (typ.)
without without
without with ±0.6 dB
400 MHz ≤ f ≤ 3 GHz ±0.5 dB
with without ±1.5 dB
±0.7 dB ±1.0 dB
with with ±0.6 dB (typ.)
without without
without with — ±0.7 dB
3 GHz < f ≤ 4 GHz ±0.7 dB ±0.8 dB
with without ±2.5 dB —
±1.0 dB
with with — ±0.7 dB (typ.) —
without without
without with — —
4 GHz < f ≤ 5 GHz ±0.8 dB
with without ±2.5 dB —
±1.0 dB
with with — — (typ.) —
without without —
without with — — —
5 GHz < f ≤ 6 GHz ±0.8 dB
with without — ±2.5 dB —
±1.0 dB
with with — — — (typ.) —
6
(meas)

(meas)

7
 Level Linearity
18 °C to 28 °C, CW
without Reverse Power Protection [without MG3710 E-043 ], [without MG3710 E-073 ]
Referenced to level: – 7 dBm
Low Power Extension High Power Extension <+1 dBm ≤–110 dBm
Frequency range
MG3710E-042/072 MG3710E-041/071 >–110 dBm >–120 dBm
without
50 MHz ≤ f < 400 MHz ±0.2 dB (typ.)
with ±0.2 dB (typ.)
without
400 MHz ≤ f ≤ 3 GHz ±0.2 dB (typ.)
with ±0.2 dB (typ.)
without/with
without
3 GHz < f ≤ 4 GHz ±0.3 dB (typ.)
with ±0.3 dB (typ.)
without
4 GHz < f ≤ 6 GHz ±0.3 dB (typ.)
with —

with Reverse Power Protection [with MG3710 E-043 ], [with MG3710 E-073 ]
Referenced to level: –10 dBm
Low Power Extension High Power Extension < –2 dBm ≤ –100 dBm
Frequency range
MG3710E-042/072 MG3710E-041/071 >–100 dBm >–110 dBm
50 MHz ≤ f < 400 MHz ±0.2 dB (typ.)
400 MHz ≤ f ≤ 3 GHz ±0.2 dB (typ.)
without/with without/with
3 GHz < f ≤ 4 GHz ±0.3 dB (typ.) ±0.4 dB (typ.)
4 GHz < f ≤ 6 GHz ±0.3 dB (typ.) ±0.4 dB (typ.)

(meas)

8
ATT Hold Function
When ATT Hold is set to ON, level adjustment is supported for continuous signal generation.
Setting Range: –10 to +10 dB (However, each upper and lower limit of the adjustment range is restricted by the signal output range.)
Resolution: 0 .01 dB

Output Connector

Connector
N-J Connector, 50 Ω (Front panel)

VSWR
without MG3710 E-043
(Output Level: ≤–7 dBm)
≤ 1 .45 (50 MHz ≤ f ≤ 3 GHz)
≤ 1 .65 (3 GHz < f ≤ 4 GHz)
≤ 1 .9 (4 GHz < f ≤ 6 GHz)
with MG3710 E-043
(Output Level: ≤–10 dBm)
≤ 1 .45 (50 MHz ≤ f ≤ 3 GHz)
≤ 1 .65 (3 GHz < f ≤ 4 GHz)
≤ 1 .9 (4 GHz < f ≤ 6 GHz)
without MG3710 E-073
(Output Level: ≤–7 dBm)
≤ 1 .45 (50 MHz ≤ f ≤ 3 GHz)
≤ 1 .65 (3 GHz < f ≤ 4 GHz)
≤ 1 .9 (4 GHz < f ≤ 6 GHz)
with MG3710 E-073
(Output Level: ≤–10 dBm)
≤ 1 .45 (50 MHz ≤ f ≤ 3 GHz)
≤ 1 .65 (3 GHz < f ≤ 4 GHz)
≤ 1 .9 (4 GHz < f ≤ 6 GHz)

Maximum Reverse Input Power

± 50 VDC (max.)
without MG3710 E-043
2 W (nom.)
with MG3710 E-043
20 W (1 MHz < Frequency of Reverse Input Power ≤ 2 GHz) (nom.)
10 W (2 GHz < Frequency of Reverse Input Power ≤ 6 GHz) (nom.)
without MG3710 E-073
2 W (nom.)
with MG3710 E-073
20 W (1 MHz < Frequency of Reverse Input Power ≤ 2 GHz) (nom.)
10 W (2 GHz < Frequency of Reverse Input Power ≤ 6 GHz) (nom.)

Signal Purity

Harmonic Spurious
(CW, Optimize S/N: Off)
without MG3710 E-043 , or MG3710 E-073
without MG3710 E-041
<– 30 dBc (Output Level: ≤+4 dBm, 10 MHz ≤ f ≤ 3 GHz)
<– 30 dBc (Output Level: ≤+4 dBm, f > 3 GHz)
with MG3710 E-041
<– 30 dBc (Output Level: ≤+4 dBm, 10 MHz ≤ f < 50 MHz)
<– 30 dBc (Output Level: ≤+12 dBm, 50 MHz ≤ f ≤ 3 GHz)
<– 30 dBc (Output Level: ≤+4 dBm, f > 3 GHz)
with MG3710 E-043 , or MG3710 E-073
without MG3710 E-041
<– 30 dBc (Output Level: ≤+1 dBm, 10 MHz ≤ f ≤ 3 GHz)
<– 30 dBc (Output Level: ≤+1 dBm, f > 3 GHz)
with MG3710 E-041
<– 30 dBc (Output Level: ≤+1 dBm, 10 MHz ≤ f < 50 MHz)
<– 30 dBc (Output Level: ≤+9 dBm, 50 MHz ≤ f ≤ 3 GHz)
<– 30 dBc (Output Level: ≤+1 dBm, f > 3 GHz)

9
 Non-harmonic Spurious
(CW, <–30 dBm ≤ Output Level ≤ +5 dBm, Offset: ≥ 10 kHz)
<– 62 dBc, –70 dBc (typ.) (100 kHz ≤ f ≤ 187 .5 MHz)
<– 68 dBc, –76 dBc (typ.) (187 .5 MHz < f ≤ 750 MHz)
<– 62 dBc, –76 dBc (typ.) (750 MHz < f ≤ 1 .5 GHz)
<– 56 dBc, –70 dBc (typ.) (1 .5 GHz < f ≤ 3 GHz)
<– 50 dBc, –64 dBc (typ.) (3 GHz < f ≤ 6 GHz)

SSB Phase Noise

(CW, Phase Noise Optimization: < 200 kHz, Offset: 20 kHz)
<– 140 dBc/Hz (nom.) (100 MHz)
<– 131 dBc/Hz (typ.) (1 GHz)
<– 125 dBc/Hz (typ.) (2 GHz)

■ 60 /150 /260 /400 MHz, CW, Optimize S/N: Off, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110
250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110
250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

10
■ 60 /150 /260 /400 MHz, CW, Optimize S/N: On, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110 250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110
250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

11
 ■ 60 /150 /260 /400 MHz, Mod = On, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110
250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
-80 60 MHz
-90
150 MHz
-100
-110
250 MHz
-120
-130 400 MHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

12
■ 850 MHz, 1 /1 .9 /2 .2 /3 .5 /5 .8 GHz, CW, Optimize S/N: Off, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

13
 ■ 850 MHz, 1 /1 .9 /2 .2 /3 .5 /5 .8 GHz, CW, Optimize S/N: On, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

14
■ 850 MHz, 1 /1 .9 /2 .2 /3 .5 /5 .8 GHz, Mod = On, with MG3710 E-002

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: <200 kHz (meas)

Single sideband phase noise

-20
-30
-40
-50
-60
-70
850 MHz
-80
-90 1 GHz
-100 1.9 GHz
-110 2.2 GHz
-120 3.5 GHz
-130
5.8 GHz
-140
-150
-160
-170
㻝㻚㻱㻗㻜㻝 㻝㻚㻱㻗㻜㻞 㻝㻚㻱㻗㻜㻟 㻝㻚㻱㻗㻜㻠 㻝㻚㻱㻗㻜㻡 㻝㻚㻱㻗㻜㻢 㻝㻚㻱㻗㻜㻣 㻝㻚㻱㻗㻜㻤
L(f) [dBc/Hz]vs. f [Hz]

Phase Noise Optimization: >300 kHz (meas)

15
 Analog Modulation

Optimize Function
Spurious Mode
Mode to control spurious problem. Controls spurious generated by the modulator.
Distortion Mode
Mode to control distortion problem. Optimizes the setting automatically to avoid distortions.
This mode can be used when the output frequency is 7 MHz or higher .

Amplitude Modulation (AM)

Internal modulation only; Specifications for modulated CW signal
AM Depth Type
Lin: Displays the AM depth type in linear.
Exp: Displays the AM depth type into the log format.
AM Depth
Range: 0 to 100 %
Resolution: 0 .1 %

(Peak Level: ≤+4 dBm, AM Depth Type: Lin, after CAL)

AM Depth Error
< 3 % of setting + 2 % (nom.) (100 kHz ≤ f < 98 MHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: ≤ 90 %)
< 2 % of setting + 1 % (nom.) (98 MHz ≤ f ≤ 2 .7 GHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: ≤ 90 %)
Distortion
< 2 % (nom.) (100 kHz ≤ f < 98 MHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: 30 %)
< 2 .5 % (nom.) (100 kHz ≤ f < 98 MHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: 90 %)
< 0 .5 % (nom.) (98 MHz ≤ f ≤ 2 .7 GHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: 30 %)
< 0 .5 % (nom.) (98 MHz ≤ f ≤ 2 .7 GHz, Modulation Rate: 1 kHz, AM Source: Sine, AM Depth m: 90 %)
Modulation Frequency Response
100 kHz ≤ f < 98 MHz, ± 1 .5 dB Bandwidth
Modulation Ratio m: 30 %
0 .1 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Modulation Ratio m: 90 %
0 .1 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
98 MHz ≤ f ≤ 2700 MHz, ±1 dB Bandwidth
Modulation Ratio m: 30 %
0 .1 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Modulation Ratio m: 90 %
0 .1 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)

Frequency Modulation (FM)

Internal modulation only; Specifications for modulated CW signal
FM Deviation
Range: F M Deviation (FM/ΦM1 setup)
0 Hz to (40 MHz-FM Deviation(FM/ΦM2 setup)) or [50 MHz – Modulation Rate] (lower value)
FM Deviation (FM/ΦM2 setup)
0 Hz to (40 MHz-FM Deviation (FM/ΦM1 setup)) or [50 MHz – Modulation Rate] (lower value)
Resolution: 0 .1 Hz

(Output Level: ≤+4 dBm, 100 kHz + 2 × (Modulation Rate + 2 × FM Deviation) ≤ f ≤ 2 .7 GHz, after CAL)
Deviation Accuracy
< 2 % of setting + 20 Hz (nom.) (Modulation Rate: 1 kHz, FM Source: Sine, 20 Hz ≤ FM Deviation ≤ 40 kHz)
Distortion
< 0 .5 % (nom.) (Modulation Rate: 1 kHz, FM Source: Sine, FM Deviation: 22 .5 kHz)
< 1 % (nom.) (Modulation Rate: 1 kHz, FM Source: Sine, FM Deviation: 3 .5 kHz)
Modulation Frequency Response
Deviation: 40 kHz, ±1 dB Bandwidth
20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)

16
Phase Modulation (PM)
Internal modulation only;Specifications for modulated CW signal
PM Deviation
Range: 0 rad. to 160 rad., or [40 MHz ÷ Modulation Rate] (smaller value)
Resolution: 0 .001 rad.

(Output Level: ≤+4 dBm, 100 kHz + 2 × (Modulation Rate + 2 × PM Deviation × Modulation Rate) ≤ f ≤ 2 .7 GHz, after CAL)
Deviation Accuracy
< 2 % of setting + 0 .02 rad. (nom.) (Modulation Rate: 1 kHz, ΦM Source: Sine, PM Deviation: ≤20 rad.)
Distortion
< 0 .2 % (nom.) (Modulation Rate: 1 kHz, ΦM Source: Sine, PM Deviation: 20 rad.)
Modulation Frequency Response
Deviation: 2 rad., ±1 dB Bandwidth
20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)

Pulse Modulation
On/Off Ratio
> 70 dB (50 MHz ≤ f ≤ 3 GHz)
> 60 dB (3 GHz < f ≤ 6 GHz)
Minimum Pulse width
1 µs (nom.)
Rise/Fall Time
≤ 50 ns (nom.) (10 to 90 %)
Pulse Repetition Frequency
DC to 1 MHz (Duty: 50 %)
External Pulse Modulation Input
AUX Connector (Rear panel), TTL
H: RF On, L: RF Off

Internal Modulation Signal

Waveform
Sine wave, Triangular wave, Square wave, Ramp wave (Positive or Negative)
Modulation Rate
Sine wave: 0 .01 Hz to 40 MHz or (50 MHz – FM Deviation)
Triangular wave, Square wave, Ramp wave: 0 .01 Hz to 4 MHz or (5 MHz – FM Deviation)
Frequency Resolution
0 .1 Hz
Phase
–180 deg to 180 deg
Phase Resolution
0 .1 deg

17
 Additional Analog Modulation Input
When MG3710 E-050 /080 is installed and for 1 st SG and 2 nd SG respectively
Internal modulation only; Specifications for modulated CW signal
Modulation Type
AM, FM, ΦM
Input Impedance
50 Ω/600 Ω/Hi-Z (100 kΩ/70 pF) (nom.)
Coupling
DC or AC is alternatively selectable.
Input Level
For set value, 2 Vp-p (nom.)
Input Frequency
DC Coupling: DC to 1 MHz (nom.)
AC Coupling: 20 Hz (typ.) to 1 MHz (nom.)
Simultaneous Modulation
AM + FM
AM + ΦM
Internal 1 + Internal 2
Internal + External
FM and ΦM cannot enabled simultaneously.
Modulation Frequency Response (AM)
Peak Level: ≤ +4 dBm, 100 kHz ≤ f < 98 MHz, AM Depth Type: Lin, ±1 .5 dB Bandwidth, after CAL
Depth m: 30 %
DC Coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC Coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Depth m: 90 %
DC Coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC Coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Peak Level: ≤ +4 dBm, 98 MHz ≤ f ≤ 2 .7 GHz, AM Depth Type: Lin, ±1 dB Bandwidth, after CAL
Depth m: 30 %
DC Coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC Coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Depth m: 90 %
DC Coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC Coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Modulation Frequency Response (FM)
Output Level: ≤ +4 dBm, 100 kHz + 2 × (Modulation Rate + 2 × FM Deviation) ≤ f ≤ 2 .7 GHz, FM Deviation: 40 kHz,
± 1 dB Bandwidth, after CAL
DC Coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC Coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)
Modulation Frequency Response (PM)
Output Level: ≤ +4 dBm, 100 kHz + 2 × (Modulation Rate + 2 × PM Deviation × Modulation Rate) ≤ f ≤ 2 .7 GHz,
PM Deviation: 2 rad., ±1 dB Bandwidth, after CAL
DC coupling: DC ≤ Modulation Rate ≤ 20 kHz (nom.)
AC coupling: 20 Hz ≤ Modulation Rate ≤ 20 kHz (nom.)

Vector Modulation

Modulation Frequency Response

Without MG3710 E-043
Internal Channel Correction: On, Output Level: –7 dBm, Random Signal of Bandwidth: 160 MHz, Crest Factor: 11 dB, 18 °C to 28 °C,
Output Frequency: 850 MHz/1 .8 GHz/1 .9 GHz/2 .2 GHz
± 0 .6 dB (At Center Frequency ±10 MHz)
± 1 .3 dB (At Center Frequency ±50 MHz)
Output Frequency: 3 .5 GHz/5 .8 GHz
± 0 .6 dB (At Center Frequency ±10 MHz)
± 1 .9 dB (At Center Frequency ±50 MHz)
With MG3710 E-043
Internal Channel Correction: On, Output Level: –10 dBm, Random Signal of Bandwidth: 160 MHz, Crest Factor: 11 dB, 18 °C to 28 °C,
Output Frequency: 850 MHz/1 .8 GHz/1 .9 GHz/2 .2 GHz
± 0 .6 dB (At Center Frequency ±10 MHz)
± 1 .8 dB (At Center Frequency ±50 MHz)
Output Frequency: 3 .5 GHz/5 .8 GHz
± 0 .6 dB (At Center Frequency ±10 MHz)
± 2 .4 dB (At Center Frequency ±50 MHz)

18
(meas)

(meas)

19
 Vector Accuracy
without MG3710 E-043 , or MG3710 E-073
Output Level: ≤
 +7 dBm (without MG3710 E-041 , or MG3710 E-071 )
≤+ 13 dBm (with MG 3710 E-041 , or MG3710 E-071 )
with MG3710 E-043 , or MG3710 E-073
Output Level: ≤
 + 4 dBm (without MG3710 E-041 , or MG3710 E-071 )
≤+ 10 dBm (with MG 3710 E-041 , or MG3710 E-071 )
18 °C to 28 °C, after CAL
W-CDMA (Test Model 4 ):
Output Frequency: 800 MHz to 900 MHz, 1 .8 GHz to 2 .2 GHz
≤ 0 .62 % (rms)
≤ 0 .6 % (rms) typ.
GSM:
Output Frequency: 800 MHz to 900 MHz, 1 .8 GHz to 1 .9 GHz
≤ 0 .84 ° (rms)
≤ 0 .8 ° (rms) typ.
EDGE:
Output Frequency: 800 MHz to 900 MHz, 1 .8 GHz to 1 .9 GHz
≤ 0 .84 % (rms)
≤ 0 .8 % (rms) typ.
LTE (20 MHz Test Model 3 .1 ):
Output Frequency: 600 MHz to 2 .7 GHz
≤ 0 .82 % (rms)
≤ 0 .8 % (rms) typ.
without MG3710 E-043 , or MG3710 E-073
Output Level: ≤
 +4 dBm (without MG3710 E-041 , or MG3710 E-071 )
≤+ 10 dBm (with MG 3710 E-041 , or MG3710 E-071 )
with MG3710 E-043 , or MG3710 E-073
Output Level: ≤
 + 1 dBm (without MG3710 E-041 , or MG3710 E-071 )
≤+ 7 dBm (with MG3710 E-041 , or MG3710 E-071 )
18 °C to 28 °C, after CAL
LTE (20 MHz Test Model 3 .1 ):
Output Frequency: 3 .4 GHz to 3 .8 GHz
≤ 0 .82 % (rms)
≤ 0 .8 % (rms) typ.

(meas)

20
Carrier Leak
18 °C to 28 °C, RMS Value: 0 dB, after CAL
≤– 55 dBc (100 MHz ≤ f < 4 GHz)
≤– 45 dBc (f ≥ 4 GHz)

Image Rejection
18 °C to 28 °C, RMS Value: 0 dB, Complex CW at 10 MHz or less, after CAL
≤– 50 dBc (200 MHz ≤ f < 4 GHz)
≤– 43 dBc (f ≥ 4 GHz)

Adjacent Channel Leakage Ratio (ACLR)

18 °C to 28 °C, W-CDMA (TestModel 1 64 DPCH)
without MG3710 E-043 or MG3710 E-073
Output Level: ≤–2 dBm (without MG3710 E-041 )
Output Level: ≤+5 dBm (with MG3710 E-041 )
with MG3710 E-043 or MG3710 E-073
Output Level: ≤–5 dBm (without MG3710 E-041 )
Output Level: ≤+2 dBm (with MG3710 E-041 )
Offset
Frequency
5 MHz 10 MHz
300 MHz ≤ f < 800 MHz ≤–68 dBc/3.84 MHz ≤–70 dBc/3.84 MHz
800 MHz ≤ f < 1 GHz ≤–70 dBc/3.84 MHz ≤–71 dBc/3.84 MHz
1 GHz ≤ f < 1.8 GHz ≤–69 dBc/3.84 MHz ≤–71 dBc/3.84 MHz
1.8 GHz ≤ f < 2.2 GHz ≤–68 dBc/3.84 MHz ≤–71 dBc/3.84 MHz
2.2 GHz ≤ f ≤ 3 GHz ≤–65 dBc/3.84 MHz ≤–71 dBc/3.84 MHz
3 GHz < f ≤ 3.8 GHz* ≤–63 dBc/3.84 MHz ≤–67 dBc/3.84 MHz

* without MG3710 E-043 or MG3710 E-073

Output Level: ≤–2 dBm
with MG3710 E-043 or MG3710 E-073
Output Level: ≤–5 dBm

21
 Level Error Compared to CW at Vector Modulation
(18 °C to 28 °C, AWGN signal, Bandwidth: 5 MHz)

without MG3710 E-043 , or MG3710 E-073

± 0 .3 dB (50 MHz ≤ f < 98 MHz, Output Level: ≤–5 dBm)
± 0 .2 dB (98 MHz ≤ f ≤ 6 GHz, Output Level: <+1 dBm)
with MG3710 E-043 , or MG3710 E-073
± 0 .3 dB (50 MHz ≤ f < 98 MHz, Output Level: ≤–5 dBm)
± 0 .2 dB (98 MHz ≤ f ≤ 6 GHz, Output Level: <–2 dBm)

I and Q Input/Output
Baseband I/Q Adjustment
DC Offset
Range: –20 .000 % to +20 .000 %
Resolution: 0 .025 %
Gain Balance
(Gain adjustment of I-phase for Q-phase)
Range: –1 .000 dB to +1 .000 dB
Resolution: 0 .001 dB
Quadrature Adjustment
Range: –10 .00 deg. to +10 .00 deg.
Resolution: 0 .01 deg.
Phase Adjustment
Range: –360 .00 deg. to +360 .00 deg.
Resolution: 0 .01 deg.
Skew Adjustment
Range: –800 .000 ns to + 800 .000 ns
Resolution: 1 ps
Delay Adjustment
Range: –400 .000 ns to + 400 .000 ns
Resolution: 1 ps

22
I and Q Input
with MG3710 E-018
Modulation Bandwidth
Baseband: 80 MHz (nom.)
RF: 160 MHz (nom.)
Input Level
√ (I 2 + Q 2 ) = 85 mV (rms), (Optimum value of level accuracy)
DC Offset
Range: –100 mV to + 100 mV
Resolution: 1 mV
Input Connector
BNC-J (Front panel)
Maximum Input Level: –1 V (peak) ≤ I, Q ≤ +1 V (peak)
Impedance: 50 Ω (nom.)

(meas)

23
 I and Q Output
with MG3710 E-018
Output Voltage Range Level
–2 .5 V to +5 V (Output: Open, Output Voltage Amplitude + DC Offset)
DC Offset
(Output: Open)
In-phase DC Offset
Range: –2 .5 V to +5 V
Resolution: 2 mV
Differential DC Offset
Range: –50 mV to + 50 mV
Resolution: 0 .1 mV
Quadrature Adjustment
Using Baseband I/Q Adjustment Function
Output Connector
BNC-J (Rear panel)
Impedance: 50 Ω (nom.)

(meas)

24
Arbitrary Waveform Generator *: S upports firmware version 2.00.00 and later. Only when using WLAN
IQproducer MX370111A and 802.11ac (160 MHz) option MX370111A-002.

Waveform Resolution
14 , 15 , 16 bits for each I/Q

Modulation Bandwidth
160 MHz*/120 MHz

Reconstruction Filter
80 MHz

Baseband Level Adjustment (RMS Value Tuning)

Adjustable Input Level to Quadrature Modulator
Decrease level: Decreases distortion
Increase level: Improves noise floor
Variable Range: ±8 dB
Resolution: 0 .01 dB

Marker Output
Waveform Resolution
14 bits: Waveform Pattern: 3 signals, or Internal Generated: 3 signals
15 bits: Waveform Pattern: 1 signal, or Internal Generated: 3 signals
16 bits: Internal Generated: 3 signals
Supports switching Positive/Negative logic pulse outputs

Internal Baseband Reference Clock

Range: 20 kHz to 200 MHz*/160 MHz
Resolution: 0 .001 Hz

External Baseband Reference Clock

with MG3710 E-017
Range: 20 kHz to 50 MHz*/40 MHz
Frequency Division, Multiplier Function: Internally Generate1 , 2 , 4 , 8 , 16 , 1 /2 , 1 /4 , 1 /8 , 1 /16 times input signals, and use as DAC Sam-
pling Clock
Input Connector: BNC-J (Rear panel, BB REF CLK Input)
Input Level: ≥0 .2 Vp-p, 50 Ω (AC coupled) (nom.)
Selects external input and MIMO connection (BB Ref Sync)

Waveform Memory
1 stRF
When MG3710 E-048 is installed, both memory A and memory B must have the same capacity. A combination of different capacities is not
available.
without MG3710 E-045 /046
64 Msamples
with MG3710 E-045 , without MG3710 E-046
256 Msamples
without MG3710 E-045 , with MG3710 E-046 , or with MG3710 E-045 /046
1024 Msamples
2 ndRF
When MG3710 E-078 is installed, both memory A and memory B must have the same capacity. A combination of different capacities is not
available.
without MG3710 E-075 /076
64 Msamples
with MG3710 E-075 , without MG3710 E-076
256 Msamples
without MG3710 E-075 , with MG3710 E-076 , or with MG3710 E-075 /076
1024 Msamples
Number of loadable files
The following numbers of waveform patterns are available per waveform memory:
Max. Package Count: 4096
Max. Patterns per Package: 4096
The maximum number of patterns in total: 4096 /waveform memory
The minimum number of samples per pattern: 128
Combination of Baseband Signal Function
1 st VSG: with MG3710 E-048
This function synthesizes the signals of two memories to generate a baseband waveform.
2 nd VSG: with MG3710 E-078
This function synthesizes the signals of two memories to generate a baseband waveform.
25
 *: S upports firmware version 2.00.00 and later. Only when using WLAN
IQproducer MX370111A and 802.11ac (160 MHz) option MX370111A-002.

Frequency Offset
± (200 MHz × 0 .8 – waveform data bandwidth) ÷ 2 (max.)* /
± (160 MHz × 0 .8 – waveform data bandwidth) ÷ 2 (max.)

Sequences Function
Selecting combination file supports following functions:
• Pattern switching method (manual, auto)
• Pattern switching position (frame end, pattern end)
• External trigger signal switches pattern at manual pattern switching
• Sequence restart function
• Maximum element: 200
• Lowest number of point by pattern: 1000
Level Ratio Setting Range: Two signal level ratio <80 dB or Off
Level Setting Resolution: 0 .01 dB
Frequency Offset
Frequency Setting Resolution: 1 Hz
Pattern Trigger
External trigger switches pattern when using waveform pattern for sequence
Input Connector
Connector: Either of BNC-J connector (Start Frame TRIG Input, Pattern TRIG1 Input) or AUX connector can be used
Input Level: TTL
Logic: Select Rise/Fall Polarity

Trigger Input
Function: Synchronizes with trigger signals and starts waveform pattern output; Switches start Trigger/Frame trigger
Start Trigger
Starts waveform output
Frame Trigger
Outputs signals at burst timing
Outputs data for burst length at frame trigger timing and waits for next frame trigger
Trigger Event
The following trigger events can be detected
No Retrigger, Buffered Trigger, Restart on Trigger
Input Connector
Function switching: Start trigger or frame trigger can be selected
Connector: Either of BNC-J connector (Start Frame TRIG Input, Pattern TRIG1 Input) or AUX connector can be used
Input Level: TTL
Logic: Select Rise/Fall Polarity

AWGN Generation Function

1 st VSG: with MG3710 E-049
2 nd VSG: with MG3710 E-079

C/N Ratio Absolute Value

≤ 40 dB

Bandwidth Limit Filter

Sets AWGN bandwidth limit as follows:
From 20 % to 80 % of waveform sampling rate

Sweep/List Function

Sweep Function
Function: Sets frequency and level sweep at 1000 -point resolution

List Function
Function: Sets sweep points for both frequency and level individually to 500 points

26
BER Measurement Function
with MG3710 E-021

Connector
Connector: AUX Connector (Rear panel)
Level: TTL

Input Signal
Data, Clock, Enable

Input Bit Rate

100 bps to 40 Mbps

Measurable Pattern
Repeat PN9 , PN11 , PN15 , PN20 , PN 23 , ALL0 , ALL1 , 01
PN 9 fix, PN11 fix, PN15 fix, PN20 fix, PN23 fix, User Define

Synchronization Establishing Condition

PN Signal: PN order × 2 -bit error free
PNfix Signal: Syncs with PN signal at PN order × 2 -bit error free;
Syncs with Pnfix signal at PN order error free from Pnfix signal header bit
Repeat ALL0 , ALL1 , 01 : 10 -bit Error Free
UserDefine: 8 -bit to 1024 -bit (variable) error free;can select header bit for Sync detection

Re-synchronization Judgment
x/y
x: Number of error bits in y bit (Setting range: 1 to y/2 )
y: Number of measurement bits (select from 500 , 5000 and 50000 )

Measurable Bit
≤ 232 – 1 bit

Measurable Error Bit Count

≤ 232 – 1 bit

Measurement End
Number of measurement bits, Number of measurement error bits

Automatic Re-synchronization
Can be toggled on and off

Re-synchronization
Count Clear, Count Keep

Measurement Mode
Single, Endless, Continuous

Display
Status, Error, Error Rate, Error Count, SyncLoss Count, Measurement Bit Number

Polarity Reversal Function

Supports polarity reversal for Data, Clock, Enable

Measured Result Reset Function

At BER measurement, hold sync status, clears measured value and measures from 0

27
 Connector *: Supports firmware Version 2.00.00 and later.
External Reference Input
Connector: BNC-J (Rear panel), 50 Ω (nom.)
Frequency: 5 , 10 , 13 MHz
Operating Range: ±1 ppm
Input Level: –15 dBm ≤ Level ≤ + 20 dBm (AC coupled)

Reference Signal Output

Connector: BNC-J (Rear panel), 50 Ω (nom.)
Frequency: 10 MHz
Output Level: ≥0 dBm (AC coupled)

Sweep Output
with MG3710 E-017
Connector: BNC-J (Rear panel), <1 Ω (Drive Capacity: 2 kΩ)
Output Level: 0 to 10 V (10 V Sweep Signal Function), 0 /5 V (Sweep Status)

Local Oscillator (LO) Input

with MG3710 E-017
Connector: SMA-J (Rear panel), 50 Ω (nom.)
Frequency: 98 MHz to 6 GHz
Input Level: –10 dBm ≤ Level ≤ + 1 dBm (AC coupled) (nom.)

Local Oscillator (LO) Output

with MG3710 E-017
Connector: SMA-J (Rear panel), 50 Ω (nom.)
Frequency: 98 MHz to 6 GHz
Output Level: ≤+1 dBm (AC coupled) (nom.) (Internal Lo output)

Baseband Reference Input

with MG3710 E-017
Connector: BNC-J (Rear panel), 50 Ω (nom.)
Frequency: 2 0 kHz to 50 MHz (External Baseband Reference Clock)*
560 MHz to 800 MHz (BB Ref Sync)*
Input Level: ≥0 .2 Vp-p (AC coupled) (nom.)

Baseband Reference Output

with MG3710 E-017
Connector: BNC-J (Rear panel), 50 Ω (nom.)
Frequency: 560 MHz to 800 MHz*
Output Level: 0 .8 Vp-p (AC coupled) (nom.)

Additional Analog Modulation Input

When MG3710 E-050 /080 is installed:
Connector: Rear panel, BNC-J
Input Impedance: 50 Ω, 600 Ω, or Hi-Z (100 kΩ/70 pF) (nom.)
Input Level: F or set value, 2 Vp-p (nom.), Absolute maximum ratings: ±5 V

External Controller
Control from external controller (excluding power-on/off)
Ethernet (10 /100 /1000 Base-T): RJ-45 (Rear panel)
GPIB: IEEE488 Bus connector (IEEE488 .2 , Rear panel)
Interface Function: SH1 , AH1 , T6 , L4 , SR 1 , RL1 , PP0 , DC 1 , DT0 , C 0 , E2
USB (B): USB-B connector (USB2 .0 , Rear panel)

USB
Hard copies waveform to external device and saves main-frame basic parameters
USB-A connector (USB2 .0 , Front panel: 2 ports, Rear panel: 2 ports)

Monitor Output
Mini D-Sub connector (compatible with VGA, Rear panel)

AUX
50 -pin (for DX10 A-50 S) (Rear panel)
Input/Output Level: TTL
with MG3710 E-017 /021 : with AUX-BNC Conversion Cable
28
Display
8 .4 -inch, XGA-color LCD (Diagonal: 213 mm, Resolution: 1024 × 768 )

General

Dimensions and Mass

426 (W) × 177 (H) × 390 (D) mm (excluding projections)
≤ 13 .7 kg (MG3710 E-032 , 034 , or 036 , excluding other options)
≤ 17 kg (including all options)

Power Supply
Power Voltage: 100 V(ac) to 120 V(ac), 200 V(ac) to 240 V(ac)
Frequency: 50 Hz/60 Hz
Power Consumption: ≤ 350 VA (including all options)
180 VA (nom.)
(with MG3710 E-032 , 034 , or 036 , with MG3710 E-041 /042 , excluding other options)
260 VA (nom.)
(with MG3710 E-032 , 034 , or 036 , with MG3710 E-041 /042 , with MG3710 E-062 , 064 , or 066 ,
with MG3710 E-071 /072 , excluding other options)
280 VA (nom.)
(with MG3710 E-032 , 034 , or 036 , with MG3710 E-041 /042 , with MG3710 E-062 , 064 , or 066 ,
with MG3710 E-071 /072 , with MG 3710 E-001 /021 , excluding other options)

Temperature Range
Operating: +5 °C to +45 °C, Storage: –20 °C to +60 °C

CE Marking
EMC: 2014 /30 /EU, EN61326 -1 , EN61000 -3 -2
LVD: 2014 /35 /EU, EN61010 -1
RoHS: 2011 /65 /EU, (EU) 2015 /863 , EN IEC 63000 : 2018

UKCA Marking
EMC: S.I. 2016 No.1091 , EN 61326 -1 , EN61000 -3 -2
LVD: S.I. 2016 No.1101 , EN 61010 - 1
RoHS: S.I. 2012 No.3032 , EN IEC 63000 : 2018

29
 Note

30
Note

31
 Specifications are subject to change without notice.

• United States • Sweden • Vietnam

Anritsu Americas Sales Company Anritsu AB Anritsu Company Limited
450 Century Parkway, Suite 190, Allen, TX 75013 U.S.A. Kistagången 20 B, 2 tr, 164 40 Kista, Sweden 16th Floor, Peakview Tower, 36 Hoang Cau Street, O Cho Dua Ward,
Phone: +1-800-Anritsu (1-800-267-4878) Phone: +46-8-534-707-00 Dong Da District, Hanoi, Vietnam
Phone: +84-24-3201-2730
• Canada • Finland
Anritsu Electronics Ltd. Anritsu AB • P.R. China (Shanghai)
Americas Sales and Support Technopolis Aviapolis, Teknobulevardi 3-5 (D208.5.), Anritsu (China) Co., Ltd.
FI-01530 Vantaa, Finland Room 2701-2705, Tower A, New Caohejing International
450 Century Parkway, Suite 190, Allen, TX 75013 U.S.A.
Phone: +358-20-741-8100 Business Center No. 391 Gui Ping Road Shanghai, 200233, P.R. China
Phone: +1-800-Anritsu (1-800-267-4878)
Phone: +86-21-6237-0898
• Denmark
• Brazil Fax: +86-21-6237-0899
Anritsu A/S
Anritsu Eletronica Ltda. c/o Regus Winghouse, Ørestads Boulevard 73, 4th floor, • P.R. China (Hong Kong)
Praça Amadeu Amaral, 27 - 1 Andar 2300 Copenhagen S, Denmark Anritsu Company Ltd.
01327-010 - Bela Vista - Sao Paulo - SP, Brazil Phone: +45-7211-2200 Unit 1006-7, 10/F., Greenfield Tower, Concordia Plaza,
Phone: +55-11-3283-2511 No. 1 Science Museum Road, Tsim Sha Tsui East,
Fax: +55-11-3288-6940 • Spain
Kowloon, Hong Kong, P.R. China
Anritsu EMEA Ltd. Phone: +852-2301-4980
• Mexico
Representation Office in Spain Fax: +852-2301-3545
Anritsu Company, S.A. de C.V. Paseo de la Castellana, 141. Planta 5, Edificio Cuzco IV
Blvd Miguel de Cervantes Saavedra #169 Piso 1, Col. Granada 28046, Madrid, Spain • Japan
Mexico, Ciudad de Mexico, 11520, MEXICO Phone: +34-91-572-6761 Anritsu Corporation
Phone: +52-55-4169-7104 8-5, Tamura-cho, Atsugi-shi, Kanagawa, 243-0016 Japan
• Austria
Phone: +81-46-296-6509
• United Kingdom Anritsu EMEA GmbH Fax: +81-46-225-8352
Anritsu EMEA Ltd. Am Belvedere 10, A-1100 Vienna, Austria
200 Capability Green, Luton, Bedfordshire, LU1 3LU, U.K. Phone: +43-(0)1-717-28-710
• Korea
Phone: +44-1582-433200 Anritsu Corporation, Ltd.
Fax: +44-1582-731303 • United Arab Emirates 5FL, 235 Pangyoyeok-ro, Bundang-gu, Seongnam-si,
Anritsu EMEA Ltd. Gyeonggi-do, 13494 Korea
• France Phone: +82-31-696-7750
Anritsu A/S
Anritsu S.A. Office No. 164, Building 17, Dubai Internet City
Fax: +82-31-696-7751
12 avenue du Québec, Immeuble Goyave, P. O. Box – 501901, Dubai, United Arab Emirates
91140 VILLEBON SUR YVETTE, France • Australia
Phone: +971-4-3758479
Phone: +33-1-60-92-15-50 Anritsu Pty. Ltd.
• India Unit 20, 21-35 Ricketts Road, Mount Waverley, Victoria 3149, Australia
• Germany
Anritsu India Private Limited Phone: +61-3-9558-8177
Anritsu GmbH 6th Floor, Indiqube ETA, No.38/4, Adjacent to EMC2, Fax: +61-3-9558-8255
Nemetschek Haus, Konrad-Zuse-Platz 1, Doddanekundi, Outer Ring Road, Bengaluru – 560048, India
81829 München, Germany Phone: +91-80-6728-1300
• Taiwan
Phone: +49-89-442308-0 Fax: +91-80-6728-1301 Anritsu Company Inc.
Fax: +49-89-442308-55 7F, No. 316, Sec. 1, NeiHu Rd., Taipei 114, Taiwan
• Singapore
• Italy Phone: +886-2-8751-1816
Anritsu Pte. Ltd. Fax: +886-2-8751-1817
Anritsu S.r.l. 11 Chang Charn Road, #04-01, Shriro House, Singapore 159640
Spaces Eur Arte, Viale dell’Arte 25, 00144 Roma, Italy Phone: +65-6282-2400
Phone: +39-6-509-9711 Fax: +65-6282-2533
2304
Printed in Japan 09/MAY/2023 ddcm/CDT Catalog No. MG3710E_DataSheet-E-A-1-(2.01)