MO1005-EA

Operation Guide 3159

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out of your
•The actual level at which some functions are disabled depends on the watch model.
purchase, be sure to read this manual carefully.
•Frequent display illumination can run down the battery quickly and require charging.

The following guidelines give an idea of the charging time required to recover from a
Keep the watch exposed to bright light
single illumination operation.
The electricity generated by the solar cell of the watch is Approximately 5 minutes exposure to bright sunlight coming in through a window
Bright Light
stored by a rechargeable battery. Leaving or using the
l l Approximately about 8 hours exposure to indoor fluorescent lighting
l

l l l l l l l
watch where it is not exposed to light causes the battery
•Be sure to read “Power Supply” for important information you need to know
to run down. Make sure the watch is exposed to light as
when exposing the watch to bright light.
Solar cell much as possible.

•When you are not wearing the watch on your wrist,

If the display of the watch is blank...
position the face so it is pointed at a source of bright
If the display of the watch is blank, it means that the watch’s Power Saving function
light.
has turned off the display to conserve power.
•You should try to keep the watch outside of your sleeve
•See “Power Saving Function” for more information.
as much as possible. Charging is reduced significantly if
the face is covered only partially.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage

or loss suffered by you or any third party arising through the use of this product or
•The watch continues to operate, even when it is not exposed to light. Leaving the its malfunction.
watch in the dark can cause the battery to run down, which will result in some watch

functions to be disabled. If the battery goes dead, you will have to re-configure watch
About This Manual
settings after recharging. To ensure normal watch operation, be sure to keep it
•Depending on the model of your watch, display text appears either as dark figures
exposed to light as much as possible.
on a light background or light figures on a dark background. All sample displays in
Battery charges in the light. Battery discharges in the dark. this manual are shown using dark figures on a light background.

•Button operations are indicated using the letters shown in the illustration.
Solar cell Bright Light
•Each section of this manual provides you with the information you need to perform
(Converts light to Electrical
operations in each mode. Further details and technical information can be found in
electrical power.) energy
the “Reference” section.

All
LEVEL 1 LEVEL 1
functions
LEVEL 2 enabled LEVEL 2

LEVEL 3 Some or all

Dis- LEVEL 3
Charge functions
charge
LEVEL 4 LEVEL 4 disabled

Rechargeable battery

World Time Mode Alarm Mode

General Guide

•Press C to change from mode to mode.

•In any mode (except when a setting screen is on the display), press B to illuminate
▲

▲
the display.

Timekeeping Mode

Press C.
Countdown Timer Mode Stopwatch Mode

▲
▲
▲

Radio-controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. 3. Press A to exit the setting screen.
•This watch is designed to pick up the time calibration signals transmitted in Germany •Normally, your watch should show the correct time as soon as you select your Home

(Mainflingen), England (Anthorn), the United States (Fort Collins), China (Shangqiu), City code. If it does not, it should adjust automatically after the next auto receive

and Japan (Fukushima, Fukuoka/Saga). operation (in the middle of the night). You also can perform manual receive or you

can set the time manually.

Current Time Setting •The watch will receive the time calibration signal automatically from the applicable

transmitter (in the middle of the night) and update its settings accordingly. For
This watch adjusts its time setting automatically in accordance with a time calibration
information about the relationship between city codes and transmitters, see
signal. You also can perform a manual procedure to set the time and date, when
“Important!” under “Time Calibration Signal Reception” and “Transmitters”.
necessary.
•See the maps under “Approximate Reception Ranges” for information about the
•The first thing you should do after purchasing this watch is to specify your
reception ranges of the watch.
Home City (the city where you normally will use the watch). For more
•You can disable time signal reception, if you want. See “To turn auto receive on and
information, see “To specify your Home City”.
off” for more information.
•When using the watch outside the areas covered by the time signal transmitters, you
•Under factory default settings, auto receive is turned off for all of the following city
will have to adjust the current time setting manually as required. See “Timekeeping”
codes: MOW (Moscow), HNL (Honolulu), and ANC (Anchorage). For details about
for more information about manual time settings.
turning on auto receive for these city codes, see “To turn auto receive on and off”.
•The U.S. time calibration signal can be picked up by the watch while in North

America. The term “North America” in this manual refers to the area that consists of
Time Calibration Signal Reception
Canada, the continental United States, and Mexico.
There are two different methods you can use to receive the time calibration signal:
•As of December 2009, China does not use Daylight Saving Time (DST). If China
auto receive and manual receive.
does go to the Daylight Saving Time system in the future, some functions of this
watch may no longer operate correctly.
•Auto Receive
•Using this watch in a country covered by a time calibration that is different from the With auto receive, the watch receives the time calibration signal automatically up to
countries it supports may result in incorrect time indication due to local application of six times a day (five times a day for the Chinese calibration signal). When any auto
summer time, etc.
receive is successful, the remaining auto receive operations are not performed. For
more information, see “About Auto Receive”.
To specify your Home City
1. In the Timekeeping Mode, hold down A until the city •Manual Receive
PM indicator City code code starts to flash, which indicates the setting screen. Manual receive lets you start a time calibration receive operation with the press of a

ll ll l
2. Press D (east) and B (west) to select the city code button. For more information, see “To perform manual receive”.
l l you want to use as your Home City.
ll

ll l l l
ll

l LIS, LON : Lisbon, London Important!

MAD, PAR, ROM, BER, STO : Madrid, Paris, •When getting ready to receive the time calibration signal, position the watch as

Rome, Berlin, Stockholm shown in the nearby illustration, with its 12 o’clock side pointing towards a window.

ATH : Athens This watch is designed to receive a time calibration signal late at night. Because of

MOW : Moscow this, you should place the watch near a window as shown in the illustration when you
Hour : Minutes Seconds
HKG, BJS, TPE : Hong Kong, Beijing, Taipei take it off at night. Make sure there are no metal objects nearby.

SEL, TYO : Seoul, Tokyo

HNL : Honolulu
ANC : Anchorage

YVR, LAX: Vancouver, Los Angeles 12 o’clock

YEA, DEN : Edmonton, Denver
MEX, CHI : Mexico City, Chicago

MIA, YTO, NYC: Miami, Toronto, New York or

YHZ : Halifax
YYT : St.Johns

•Make sure the watch is facing the right way.