Aircraft Flexible Maintenance Schedule (Rev 19)
002-028-001 (Rev Mar.08)
INSPECTION C7
050330
Note: Page count shown in any List of Effective Pages table is for the paper copy only. The actual page count may differ when printed from this electronic version.
List of Effective Pages
Page 1 thru 4, Issued Mar.08
Instructional Data
NOTE
Before you proceed with this inspection make sure that you have read and understood the introduction section at the
front of this schedule.
NOTE
Inspection C7 must be signed off only when accomplished in a phased method and must be completed every 1600 hours.
Completion of Inspection
Aircraft registration:
Aircraft total airframe hours:
Date of completion of inspection:
Checked by: License #
Area F4: Rear equipment bay and rear fuselage.
Access: Tail cone F2 and hydraulic box cover F92 removed.
Aircraft Registration: Mechanic Inspector
Area Inspection
050331 (a) Airframe:
(b) Engine:
(c) Electrical:
(d) Avionic:
NOTE
Make sure ALL area inspections are done in accordance with the Inspection Requirements detailed in
Para.(6) of the Introduction at the front of this schedule.
Air Conditioning
210011 Air conditioning ducts ( AMM 21-10-15):
• Inspect for satisfactory condition.
210012 Ram air duct. Inspect, as far as is possible, for cracks in the vicinity of the take-
off duct to the shut-off valve, and around the cut-out for the inward relief door.
Electrical Power
Copyright © Textron Aviation Inc. Page 1 of 3
Retain printed data for historical reference only. For future maintenance, use only current data. Print Date: Wed Oct 12 13:02:48 CDT 2022
Aircraft Flexible Maintenance Schedule (Rev 19)
002-028-001 (Rev Mar.08)
240011 Busbar PE, PS1 and PS2 feeder fuses. Replace (with new items) the
fuses:
• F31 an F32 on panel ZL.
• F13, F14, F23 and F24 on panel GA
When you do this:
• Make sure the fuses are in correct contact with the busbars and the
mounting pillars.
• Make sure the fuses are clamped in position correctly.
• Torque tighten the securing nuts (AMM 24-01-00).
240012 Busbar PE, PS1 and PS2 feeder system connections:
• Inspect for discoloration due to overheating.
• Torque tighten the connections (AMM 24-01-00).
Flight Controls
270037 Elevator primary and elevator trim control cables. Check cable tensions
are correct (AMM 27-30-00).
270038 Rudder primary and rudder trim control cables. Check cable tensions are
correct (AMM 27-20-00).
270039 Elevator autopilot servo control cables. Check cable tensions are correct
(AMM 27-30-81).
270040 Rudder autopilot servo control cables. Check cable tensions are correct
(AMM 27-20-121).
270041 Elevator autopilot trim-servo control cables. Check cable tensions are
correct (AMM 27-30-00).
Hydraulic Power
290006 Suction filter (Pre-Mod. 253203). Replace the filter element (AMM 29-10-21).
NOTE
Mod. 253203 introduces suction filter AIR87366/0 with a finer filter
element.
290007 Hydraulic tank pressurization system. Drain any accumulation of liquid from
the drain/ground air charge connection.
Navigation
340007 Autopilot servo units, rudder and elevator.
• Inspect, particularly for cable and capstan wear, contamination, cable
spool-off angle and security of the servo unit and mount.
• With the autopilot disengaged operate the control system throughout
the entire range and make sure there is no unusual noise, binding,
backlash or signs of other mechanical irregularities from the servo
mount.
Copyright © Textron Aviation Inc. Page 2 of 3
Retain printed data for historical reference only. For future maintenance, use only current data. Print Date: Wed Oct 12 13:02:48 CDT 2022
Aircraft Flexible Maintenance Schedule (Rev 19)
002-028-001 (Rev Mar.08)
340008 Autopilot elevator trim servo unit and mount.
• Inspect, particularly for cable and capstan wear, contamination, cable
spool-off angle and security of the servo unit and mount.
• With the autopilot disengaged operate the control system throughout
the entire range and make sure there is no unusual noise, binding,
backlash or signs of other mechanical irregularities from the servo
mount.
Oxygen
350008 Oxygen cylinder.
• Inspect cylinder mount clamps for security.
General Lubrication
Aircraft Registration: Mechanic Inspector
120023 Do any 1600 hour lubrication requirements for Area F4, refer to Part 7 -
LUBRICATION.
Copyright © Textron Aviation Inc. Page 3 of 3
Retain printed data for historical reference only. For future maintenance, use only current data. Print Date: Wed Oct 12 13:02:48 CDT 2022
