G.C.N.

: 47-116-73 (24 kW)

G.C.N.: 47-116-74 (30 kW)
G.C.N.: 47-116-75 (38 kW)
G.C.N.: 41-116-41 (18 kW)
G.C.N.: 41-116-42 (24 kW)
G.C.N.: 41-116-43 (30 kW)

CLAS HE EVO
CLAS HE EVO System
USER’S MANUAL
CONDENSING WALL-HUNG GAS BOILER

Country of Destination: GB/IE

HOT WATER I HEATING I RENEWABLE I AIR CONDITIONING

USER’S MANUAL

Dear Customer,
GUARANTEE
Thank you for choosing an ARISTON boiler. The appliance is guaranteed for 5 years from the date of
We guarantee that your boiler is a reliable and technically purchase.
sound product. Aristons only obligation under the guarantee will be to repair
or replace the faulty appliance at Aristons discretion. This will
This manual provides detailed instructions and
be carried out where the fault arises from within defects in the
recommendations for proper installation, use and appliance, caused either by material or workmanship of the
maintenance. manufacturer.
Remember to keep this manual in a safe place for future This guarantee does not protect malfunction or damage arising
reference i.e. by the gas meter. from incorrect installation, commissioning or maintenance
procedures as laid out in the installation and servicing manual,
Your local ARISTON Servicing Centre is at your complete inefficient flue system, poor or incorrect electricicty, wrong gas
disposal for all requirements. supply or pressure, tampering by inexperienced persons and
any other cause not directly due to manufacture.
Ariston Thermo UK Ltd cannot accept responsibility for any
cost arising from repair or maintenance carried out by any third
party.
Service under the guarantee does not affect the expiry date
of the guarantee. The guarantee on parts and appliances
which are exchanged ends when the guarantee on the original
appliance expires.
This guarantee does not affect your statutory rights.
The boiler must be registered with Ariston within 30 days from
date of installation.
Registration is online at www.ariston.co.uk.

2/
 USER’S MANUAL

The installation and first ignition of the boiler

must be performed by qualified personnel in
compliance with current national regulations
regarding installation, and in conformity
with any requirements established by local
authorities and public health organisations.
After the boiler has been installed, the installer
must ensure that the end user receives the
declaration of conformity and the operating
manual, and should provide all necessary
information as to how the boiler and the safety
devices should be handled.
This appliance is designed to produce hot water for domestic use
(combi version).
It should be connected to a heating system and a distribution
network for domestic hot water, both of which must be compatible
with its performance and power levels.
The use of the appliance for purposes other than those specified is
strictly forbidden. The manufacturer cannot be held responsible for
any damage caused by improper, incorrect and unreasonable use
of the appliance or by the failure to comply with the instructions
given in this manual.
Installation, maintenance and all other interventions must be
carried out in full conformity with the governing legal regulations
and the instructions provided by the manufacturer. Incorrect
installation can harm persons, animals and possessions; the
manufacturing company shall not be held responsible for any
damage caused as a result.
In the event of any maintenance or other structural work in the
immediate vicinity of the ducts or flue gas exhaust devices and
their accessories, switch the appliance off by switching the external
bipolar switch to the “OFF” position and shutting off the gas valve.
When the work has been completed, ask a qualified technician to
check the efficiency of the ducting and the devices.
If the boiler should be out of use for a prolonged period, it is
recommended that the electrical power supply be disconnected
and that the external gas cock be closed. If low temperatures are
expected, the boiler and system pipe work should be drained in
order to prevent frost damage.
Turn the boiler off and turn the external switch “OFF” to clean the
exterior parts of the appliance.
Do not allow children or inexperienced persons to use the
appliance without supervision.

CE labelling
The CE mark guarantees that the appliance conforms to the
following directives:
- 2009/142/CEE
relating to gas appliances
- 2004/108/CEE
relating to electromagnetic compatibility
- 92/42/CEE
relating to energy efficiency
- 2006/95/CEE
relating to electrical safety
- 2009/125/CE
Energy related Products
- 813/2013
Commission regulation (EU)

/3
USER’S MANUAL

SAFETY REGULATION Do not use insecticides, solvents or

aggressive detergents to clean the appliance.
Key to symbols: Damage to plastic and painted parts.
Failure to comply with this warning Do not use the appliance for any use
implies the risk of personal injury, in some other than normal domestic use.
circumstances even fatal Damage to the appliance caused by
Failure to comply with this warning implies operation overload.
the risk of damage, in some circumstances Damage caused to objects treated
even serious, to property, plants or animals. inappropriately.
Do not allow children or inexperienced
individuals to operate the appliance.
Do not perform operations which involve
Damage to the appliance caused by
opening the appliance.
improper use.
Electrocution from live components.
If you detect a smell of burning or smoke
Personal injury caused by burns due to
coming from the appliance, disconnect it
overheated components, or wounds caused by
from the electricity supply, turn off the main
sharp edges or protrusions.
gas valve, open all windows and call for
Do not perform operations which involve
assistance.
removing the appliance from its installation
Personal injury caused by burns, smoke
space .
inhalation, intoxication.
Electrocution from live components.
If there is a strong smell of gas, turn off the
Explosions, fires or intoxication caused by
main gas valve, open all windows and call for
gas leaking from disconnected piping.
assistance.
Flooding caused by water leaking from
Explosions, fires or intoxication.
disconnected piping.
Do not damage the power supply cable.
Electrocution from live uninsulated wires.
This appliance can be used by children aged
Do not leave anything on top of the
from 8 years and above and person with reduced
appliance.
physical, sensory or mental capabilities or lack
Personal injury caused by an object falling
of experience and knowledge if they have been
off the appliance as a result of vibrations.
given supervision or instruction concerning use
Damage to the appliance or items
of the appliance in a safe way and understand the
underneath it caused by the object falling
hazards involved. Children shall not play with the
off as a result of vibrations.
appliance. Cleaning and user maintenance shall
Do not climb onto the appliance.
not be made by children without supervision.
Personal injury caused by the appliance
falling.
Damage to the appliance or any objects
underneath it caused by the appliance
falling away from its installation space.
Do not climb onto chairs, stools, ladders
or unstable supports to clean the appliance.
Personal injury caused by falling from
a height or cuts (step ladders shutting
accidentally).
Do not attempt to clean the appliance without
first switching it off and turning the external
switch to the OFF position.
Electrocution from live components.

4/
 USER’S MANUAL

Control panel

2 12

3
11
2 1 24

4 3 23

22
4
12

21
5
I
10

20
6
9

19
7

18
8

17
9
6

16
10
11 15
12 13 14

5
9
6 8
7
Legend :
1. Display
2. Domestic Hot Water adjustment button +/-
(only for Clas HE EVO models)
3. MODE button
(Operation mode selection (summer/winter)
4. Pressure gauge
5. Auto Function and/or Comfort Function
enable/disable button
(Comfort function only for Clas HE EVO models)
6. ESC button - reserved for technical assistance
7. “encoder” programming knob
- reserved for technical assistance
8. OK button - reserved for technical assistance
9. ON/OFF button
10. TIME CLOCK (option for System boilers))
11. RESET button
12. Heating temperature adjustument button +/-

Digits indicating: Hot Water Comfort activated

- boiler status and temperature Boiler off with antifreeze function active
indication (°C)
- error code signals (Err) Antifreeze function activated
- menu settings AUTO function activated
AUTO
Technical assistance request (Temperature regulation activated)

Flame detected with indication of Clip-in solar connected (optional)

power used or indication of operation
shutdown
Heating operation set

Note: A radio frequency (RF) Programmable Room

Heating operation active Thermostat is available from Ariston stockists.
Hot water operation set The Receiver unit can be fitted in the time clock
position (10)
Hot water operation active

/5
USER’S MANUAL

Initial operating procedures Ignition procedure

If the boiler is installed inside the apartment, make sure that Press the ON/OFF button 9 on the control panel to switch on the
all provisions relating to the air inlet and room ventilation (in boiler. The display shows:
compliance with current legislation) are respected.
Check the water pressure on the display regularly and make sure
that the figure is between 0.6 and1.5 bar when the system is cold.
If the pressure is just under the minimum value the display will
request a filling procedure.
Re-establish the correct pressure by filling loop.
If the pressure drops very frequently, there may be a water leak at
some point in the system. If this is the case a plumber should be
contacted.

CLAS HE EVO ● the operating mode:

Winter

Summer

Only Heating (CLAS HE EVO System)

● The figures indicates:

- the flow temperature when no heating requests have been made
2 - the flow temperature in central heating mode
- the temperature of the hot water in domestic hot water
1

Note.
Note: Connections viewed from behind boiler
Connections viewed from
behind boiler. 3

CLAS HE EVO SYSTEM

Operating mode selection
Use the MODE button 3 to select the desired operating mode.

Operating mode Display

heating + hot water production for domestic use -

winter

hot water production for domestic use only -

summer
2
Only heating (only for System models)
1

The ignition of the burner is indicated on the display by the symbol

Note. the dashes underneath indicate the power utilised. .
Connections viewed
Note: Connections viewed from
from behind boiler

behind boiler.
3

1. To repressurise the system ensure flexible hose 3 is connected

2. Slowly open taps 1 & 2 (see diagrams above)
3. Water will be heard entering the system
4. When the pressure gauge reads 1.5 bar close taps 1 & 2

6/
 USER’S MANUAL

Adjusting the heating Switching off the boiler

It is possible to set the temperature of the heating water by pressing To switch off the boiler press the ON/OFF button, the display will
the buttons 12. switch off.
The temperature that may be obtained which varies from: The Anti-frost Function is already active.
- 20°C to 45°C (low temperature)
- 35°C to 82°C (high temperature). ATTENTION!!
Switch off the boiler completely by switching the external electrical
switch to the OFF position. Shut off the gas valve..

Domestic hot water temperature adjustment

only for CLAS HE EVO MODELS
It is possible to set the temperature of the domestic hot water by
adjusting the button 2 a temperature may be obtained which varies
Clock Instructions
from about 36°C to about 60°C.
The value set previously will flash on the display.

A
2 1 24
3 23

22
4
12

21
5
C
I

20
6

19
7

18
8

17
9

6 B

16
10

11 15
12 13 14

Switching off the heating

To switch off the heating, press the MODE button 3; the heating
operation symbol will disappear from the display. The Mode button
1. General layout
can be used to keep the domestic hot water production process
The mechanical clock covers a 24 hour period. Each tappet represents
active or to place it in standby (modes deactivated).
15 minutes A. An override switch is located on the clock B.
In the figure below the boiler remains active only for the production
of domestic hot water, indicating the set temperature.
2. To set the time
To set the time of day, grasp the outer edge of the dial and turn
slowly clockwise until the correct time is lined up with the arrow C.

3. To Set the “On” and “Off ” times

The clock uses a 24hours system. e.g. 8 = 8.00 am and 18 = 6.00 pm
“ON” periods are set by sliding all tappets between the “ON” time and
the “OFF” time to the outer edge of the dial. The tappets remaining
at the centre of the dial are the “OFF” periods.

4. For operation
Put the selector switch B to the symbol to control the central
heating by the clock. Put the switch B to “I” to select permanent
operation or to “0” to turn the central heating off permanently.

/7
USER’S MANUAL

COMFORT / AUTO Function

To activate the Comfort function or AUTO function it is necessary to
press the button 5

COMFORT function (CLAS HE EVO models) Auto button - Temperature adjustment activation
The comfort mode has priority over any other heating request. The AUTO function enables boiler operation to be adapted to
There are two settings for the comfort mode (they can be adjusted environmental conditions and to the type of system it is installed on.
in the parameters menu): Comfortable temperature is reached inside the room in the quickest
1. As soon as DHW is drawn, the secondary heat exchanger is kept way possible, without wasting money, energy or efficiency, while
warm for 30 mins. substantially reducing the amount of wear experienced by the
2. As soon as DHW is drawn, the secondary heat exchanger is kept components.
warm permanently.
This function may be enabled by pressing the COMFORT button. Your installer will advise you on the devices connectable to the
boiler and will program it according to the system.

In normal boilers the water temperature inside the heating elements

is usually set to a high value (70-80°C), thereby ensuring effective
heating during the few really cold winter days. It then becomes
excessive on less cold days (of which there are many) more typical
of the autumn and winter seasons. This leads to excessive room
heating after the thermostat has been switched off, resulting in
energy waste and uncomfortable conditions inside the room.
The AUTO function “takes control” of the boiler and selects the best
operating regime based on environmental conditions, external
devices connected to the boiler and the performance required. It
constantly decides at which power level to operate based on the
environmental conditions and the room temperature required.

Note
Esc, Ok and Encoder
The Esc, Ok and Encoder are reserved for use by the service
technician.
If one of these buttons/knobs are activated by accident by the end
user ‘SERV’ is displayed
This will deactivate after a few seconds.
All other button are reserved for use by the end user

8/
 USER’S MANUAL

Appliance shut-off conditions Operation shutdown error table

The boiler is protected from malfunctions by means of internal Anti-frost Device.
checks performed by the electronic P.C.B., which stops the boiler
from operating if necessary. In the event of the boiler being shut off Display Description
in this manner, a code appears on the control panel display which
refers to the type of shut-off and the reason behind it. 1 01 Overheating
Two types of shut-off may occur: 5 01 No flame detection

Safety shut-off 1 03
This type of error is “volatile”, which 1 04
means that the boiler starts up again 1 05 Insufficient circulation
automatically as soon as the problem
which caused the shut-off is removed. 1 06
The display will flash ”Err” and the 1 07
error code.
1 08 Insufficient water (request filling)
In fact, as soon as the cause of the
shut-off disappears, the boiler starts 3 05 P.C.B error
up again and continues to operate 3 06 P.C.B error
normally.
While the boiler is shut off for safety reasons, it is possible to attempt 3 07 P.C.B error
to restore normal operation by switching the appliance off and on
again using the ON/OFF button on the control panel. The anti-frost function acts on the central heating flow temperature
If the boiler still indicates a safety shut-off, switch it off. Make sure probe, independently from other settings, when the electrical
the external electric switch is in the OFF position, close the gas tap
supply is turned on.
and contact a qualified technician.
If the primary circuit temperature falls below 8°C the pump will run
for 2 minutes.
Safety shut-off due to insufficient water pressure
After the two minutes of circulation (fixed) the boiler will check the
If the water pressure inside the
following:
heating circuit is insufficient, the
a) if the central heating flow temperature is > 8°C, the pump stops;
boiler will perform a safety shut-off.
b) if the central heating flow temperature is between 4 and 8°C, the
(See table).
pump will run for another two minutes;
To re-pressurise the boiler, it will
c) if the central heating flow temperature is < 4°C, the burner will
be necessary to connect the silver
flexible hose supplied to the two fire (heating position) at minimum power until the temperature
isolating points underneath the reaches 33°C, the burner will go off and the pump will continue
boiler, once the hose is connected, to run for two minutes.
open up both of the black quarter The anti-frost device activates only when (with the boiler operating
(see p.5) turn handles, once the pressure reads 1.5 bar on the correctly):
display, close both handles and disconnect the hose . - the system pressure is correct,
If the pressure drops very frequently, there may be a water leak - the boiler is electrically powered,
at some point in the system. If this is the case please contact your - there is a supply of gas.
installer and ask them to check it.

Operation shutdown
This type of error is “non volatile”, which means that it is not removed Change of gas type
automatically. The display will flash Err and the error code. Our boilers are designed to function either with Natural Gas
In this case the boiler does not restart automatically, but it may (methane) or Propane. If you need to change from one gas to the
be reset by pressing the button. If the problem manifests other, one of our Authorised Service Centres must be contacted to
itself again after several attempts to reset the appliance, contact a convert the appliance.
qualified technician.
IMPORTANT Maintenance
Schedule an annual maintenance check-up for the boiler with a
competent person.
Correct maintenance always results in savings in the cost of
running the system.
Failure to arrange an annual service for the appliance will invalidate
the second year and subsequent years of the manufacturers
guarantee.

IF THIS SHUTDOWN OCCURS FREQUENTLY, CONTACT AN

AUTHORISED SERVICE CENTRE FOR ASSISTANCE. FOR SAFETY
REASONS, THE BOILER WILL ALLOW A MAXIMUM OF 5 RESET
OPERATIONS TO TAKE PLACE IN 15 MINUTES (INDIVIDUAL
PRESSES OF THE BUTTON).

/9
 5 Year Guarantee
Terms & Conditions
WHAT ARISTON REQUIRES
The boiler must be registered with Ariston within 30 days from date of installation. Registration is on line at
www.ariston.co.uk
The boiler must be installed in accordance with the manufacturers instructions
The boiler must be installed by a Gas Safe Registered engineer.
The installer must arrange for a Building Regulations Compliance Certificate to be issued to the boiler owner.
The Building Regulations Compliance Certificate is to be made available upon request by any attending Ariston
service representative.
The Benchmark commissioning checklist, which can be found at the back of the Installation instructions, must be
completed in full by the installer.
The completed Benchmark checklist must be left with the boiler or be made available upon request by any attending
Ariston representative.
The boiler must be serviced by the 12 month anniversary of the installation. This must be carried out by a Gas Safe
Registered engineer.
Proof of annual service must be made available upon request by any attending Ariston representative.
The boiler must be installed on a clean system and corrosion inhibitors added.

All of the above are standard procedures which a competent installer will be aware of.
Failure to comply with any of the above will result in any guarantee being withdrawn.

CONDITIONS OF THE 5 YEAR GUARANTEE

If an Ariston engineer is required to attend to the appliance and the failure is caused by either an installation error,
user error or any other external cause, then a “waste call” charge will be made. If the waste call charge is not paid,
then any extended warranty will cease.
The 5 Year Guarantee is only applicable to appliances installed in the United Kingdom.
The following is not covered under the guarantee:
Any external boiler controls (other than those supplied by Ariston), pipework and radiators
Loss or damage caused by using the boiler in a non-domestic or commercial environment.
Loss or damage caused by accident, theft, attempted theft, malicious damage or damage caused by fire or explosion.
Damage caused by any disaster affecting the equipment including neglect without limitation.
Clearing airlocks and partially or fully blocked pipes or work caused by equipment, which has not installed correctly.
Claims arising from any problem with the supply of electricity, gas or water.
Consequential loss or damage arising directly or indirectly caused by the boiler not working.
Cosmetic damage.
Costs arising from difficulties in getting to the boiler. This includes: pipe work under floor boards or pipe work
contained in the fabric of the building. Ariston requires the warranty holder to carry out whatever works are necessary
to enable Ariston staff or nominated representatives to gain access the boiler prior to arrival.
Any water pressure adjustments on sealed systems, Claims arising from scale damage.
Any modification, alteration to the boiler carried out without permission or authority from Ariston.

ARISTON THERMO GROUP

 ITALIAN DESIGN

Ariston Thermo UK Ltd

Artisan Building
Hillbottom Road
High Wycombe
Bucks HP124HJ
Telephone: 01494 418500

ariston.com/uk
420010620000 - 0415

Technical Advice: 0333 240 7777

Customer Service: 0333 240 8777