Suluva Saibhargav 1.

What is difference between super critical and sub critical

2.What is draft
3.How the flame is maintained
4.What is a boiler
5. On which principle generator works
6.What happens if steam input increase to the turbine
7.What happens if speed increase
8.Why we should maintain frequency constant
9.How the active power is injected into the grid
10.How the active is increase
11.What happens if the generator is island mode
12.What happens if the steam is increased when the generator is islanding mode?
13.How the motor testing is done?
14.What is insulation test
15.How the insulation test is done?
16.How will you decide that the motor is not working?
17.What should be the insulation resistance of motor
18.What is pI
19.What is difference between PI and megger test
20.What Is total generator of plant today
21.What is failure happened today
22.Why insulation deteriorates
23.Which material is used in motor winding
24.What are testing of motor
25.What is CT testing and CT rating?

Sutopa Mohato 1. What is the Power System?

2. Power System Stability?
3. Why is transmission done at high voltage?
4. What is inter grid connection? (2012 Blackout)
5. Types of Relay? Difference b/w circuit breaker & Isolator.
6. Zones in Transmission line.
7. Generator working principle.
8. Ratings of Motors in JPL 600MW (SAT & UAT).
9. Working of Differential Protection Relay.
10 Difference between reliability & redundancy.
11. What is DPR (differential protection relay)?

Abibhas Ranjan 1.what is your role in power plant as an electronics engineer.

Mohanta 2.Do you know how to operate plant from DCS room.
3.Can you read and repair Card?
4.what is CLC & OLC ?
5.In power plant where we use clc and olc?
6.in PAFan, ID fan & FD fan , where clc and olc are used.
Aditya Singh 1) Classify sensor and there type
2) What is orific and venturi flow meter
3) How to measure pressure
4) What is signal conditioning
 5) working of RTD and Thermocouple
6) how infrared sensor work
7) what is the velocity of orific flow meter
8) Difference between transducer and transmitter
9) difference between plc and dcs
10) difference between rtd and thermocouple
11) What is the purpose of a PID controller?
12) what Instrumentation Amplifiers (InAmps) are used for?
13) What is a 4-20mA signal and why is it widely used in industrial control systems?
14) How does a differential pressure transmitter work?
15) What is two wire and three wire RTD system ?
Akash Kumar Mishra 1-what is six sigma
2-what is the role of instrumentation in power plant
3-Examples and explain instruments which is used in plant
4-working and flow measurement of orifice plate
5-Give the picture to identify instruments (aero foil, flow measurement orifice)
6-from scheme tracing some questions
Animesh Panigrahi 1. What is weldability?
2. What is the gas used in welding in jpl tamnar plant ?
3. What are the components of hydraulic motor?
4. Where synchronous motors are used in the plant?
5. What is hydraulic film?
6. What is the oil pressure inside the bearing when the turbine is in full load ?

Badal Behera 1.Tell me about your Internship

2.What is the difference between Subcritical and Supercritical
3.What is Latent point
4.What is the temperature of Latent heat of vapourisation
5.Draw the Complete Plant diagram and process in deatils

Kshitij Sharma 1. Tell me about yourself?

2. Tell me about your hobbies and which thing makes you happy ?
3. Tell me about your branch (ECE) and why you join power sector ?
4. Draw the scheme from measure instrument to the HMI .
5. Draw the DPU panel and how much bit of DPU.
6. Overview of DCS system .
7. Types of drum seperations?
8. Favorite subject questions (Digital electronics) ? About the FET , BJT And their types?
Manisha Raila
N Likhith 1.Difference between super critical and ultra super critical plant
2.What kind of materials used in water wall system in ultra super critical
3.Draw iron carbon diagram (and questions in depth)
4. Efficiency of turbines
5. Efficiency of condenser
6.Boiler efficiency
7.Effectiveness of chimney
8. Difference between natural draft and induced draft cooling towers
9. Why should we maintain vacuum in condenser
10. What type of vacuum pump is used
11. What do you mean by NPSH
12. Temp and pressure of drum in supercritical
13. Function of CEP
14. Final year project ( in-depth)
15. Work experience (intern)
16. Why did you choose to work in thermal power plant
17. Where do you see your self in 5 years
Prashant kumar Rai 1.Condensate cycle
2.Range of different types of waves
3.How data transfer from one phone to other

Prince Kumar Singh

Rajewar Kumar 1) why deaerator kept at height?

Panda
2) Brake power, hydraulic power, pump characteristics curve.

3)NPSH calculation

4) oring purpose

5) Stuffing box

6) Mechanical seal and gland packing difference

 7) Nessult Number

8) iron carbon diagram

9) what happened if down commer kept inside

Satyam Yadav 1:QUESTIONS RELATED TO SOLAR AND WIND (HOW ELETRICITY GENERATED FROM THIS
AND WHAT COMPONENTS ARE USED TO GET AC OUTPUT )

2:GENERATOR (FROM GENERATOR TO SWITCHYARD SLD DIAGRAM )

3:DRAW BOTH STATIC AND BRUSHLESS EXCITATION

Saswata Pradhan 1.Intro About yourself

2.About carrier like 10 ,12 from where and the btech institute, what you are doing etc
3.Question on internship done:
4.About cfbc boiler working, difference in cfbc and pf boiler
5.Difference in cfbc and pf boiler fuel firing system
6.How fire balls creates in pf boiler
7.Justify circulation fludized bed combination and explain the firing system
8.What done in internship

9.Question on project done :

10.About the project
11.How it will be help ful for mankind explain
Core mechanical :
12.Types of pumps
13.Difference in impulse and reaction turbine
14.Little bit questions from strength of materials about carbon percentage in different types
of steel.
Power plant
15.Draw the steam follow scheme
16.Why the condenser is spring suspended
17.Why Hp lp by pass system used
18.How to achieve steam parameters during start up condition
19.Why shocking is important when turbine is in rolling conditions
20.Importance of condenser and why it is in vaccum
Shreesh Chandra 1) what is IEEE RULES
Shukla 2) single line diagram of switchyard 250 and 600

1.What is an exciter? Explain main and pilot exciter.

Smriti Adhikari 2.What is an AVR?
3.Explain Generator protections.

1.Tell about yourself

2.Have u visited C&I already in plant
3.Which electronic device we use in field
4.Draw flue gas path
Sneha Gupta 5.ESP
6.Corona Effect in ESP
7.How many ESP Hoppers
8.Efficiency of ESP
9.Gases produced by ESP
10.Electronics device on ESP Top
Suraj Anil Rajurkar

Shashi Kumar Singh