GROUND PENETRATING RADAR OKO

GEOTECH
GEOPHYSICAL EQUIPMENT FOR
ENGINEERING GEOPHYSICS

GPR OKO-3

Electrical exploration instruments

Seismographs
 GPR OKO

Highways, runways investigation

Concrete inspection

Railways embankment examination

Geological structures mapping

Archeology

Ice thickness measurement

Basin exploration and

near bottom sediments
mapping

+7 (495) 641-2-641 [email protected] geotechru.com

 GROUND PENETRATING RADAR OKO

Ground Penetrating Radar OKO-3

OKO-3 GPR is high-performance systems including a control unit (or

control processing unit) and antennas with frequenices from 15 to 2500
MHz
OKO-3 GPR allows customers to use tablets, smartphones, labtop, etc.,
perform high-precision coordinate referencing, and apply new software
options.

OKO-3 GPR. What’s new?

Number of samples per scan - from 4096 to 16384
Scan interval - up to 350-400 scans/sec (512 samples)
High-speed dual-channel control unit (total scan interval 700-800
traces/sec.)
Built-in WI-FI in the control unit for connecting to a laptop
More accurate positioning by providing the ability to connect
GNSS-receiver to the control unit
"Intelligent" odometer. Odometer parameters are recorded in its
non-volatile memory and are automatically set when turned on
"Light version" of the "CartScan" software for the "Android" operating
system for use with rugged tablets and smartphones

Linear concrete
structures

Paving slabs

sand

Made ground
( sand -gravel)

Linear objects Foundation soil

underground utilities

+7 (495) 641-2-641 [email protected] geotechru.com

 GPR OKO
THE OKO-3 GPR SET INCLUDES

Control unit or control processing unit;

Сontrol Unit One of the antennas with frequencies from 25 to 2500 MHz;
Additional equipment (an odometer, GPS and Wi-Fi modules, etc.).

one-channel control unit

dual-channel control unit

Antennas are interchangeable and easily replaceable

All antennas are compatible with the control unit or
a control processing unit
It is optimal to combine antennas of different frequencies;
Dual-frequency antennas make it possible to locate targets at two
depths simultaneously
Horn antennas are designed for road examination
Соntrol Processing
Unit

The Control Processing Unit

was designed especially to
operate in unfavorable
weather conditions
(temperature -30 …+50°С)

+7 (495) 641-2-641 [email protected] geotechru.com

 OKO CONTROL PROCESSING UNIT

The Control Processing Unit OKO-3 is a lightweight, portable, two-channel

microprocessor control unit, designed for managing all of a ground penetrating
radar's operating modes. It displays all GPR profiles, saving them on a
Flash-disc, GPR survey results' processing and data exchange with personal
computer via USB interface, and can be connected to one or
two antenna units.
Features
The Control Processing Unit OKO-3 is specially designed for usage in adverse
weather conditions and can be used in all climatic conditions (operating
efficiency is guaranteed in temperatures ranging from -20°С to +50°С).

Data are displayed on LCD with a window width of 10,4'' and a resolution
of 1024x768. The screen allows one to view data in real time or in playback
mode. It is readable in bright sunlight, although an optional sunshade for
the unit is available. Prolonged exposure to direct sunlight will cause
the screen to heat up and may affect screen visibility.

The Control Processing Unit OKO-3 operation has been simplified for
maximum effectiveness. A touch screen allows one to easily select
parameters and modes, while the power switch-on function and cursor
are effortlessly performed with the help of moisture-protected
buttons located on the front bar.

+7 (495) 641-2-641 [email protected] geotechru.com

 OKO CONTROL PROCESSING UNIT
GPR OKO
Obtained data are saved on an integrated SSD-disc with a
capacity of 120,0 GB.
The Control Processing Unit OKO-3 can be charged from a
14.8 V Lithium-Ion rechargeable batteries with a 5 Ah capacity,
mounted into the housing.
Survey time with two fully charged batteries is approximately 8
hours. Batteries are charged with an available battery charger.

System
Antennas Compatible with all OKO antennas
Number of Channels Records data from 1 single-frequency antenna,
2 single-frequency antenna or 1 dual-frequency antenna
Data Storage 120 GB
Display 10.4" LED high brightness display,
Active matrix 1024 x 768 resolution and 18-bit color
GPS Data logged internally (via USB)
Data Acquisition
Data Format OKO-2 (gpr, gpr2)
Output Data Format 32-bit
Number of Channels 1 or 2 channels
Number of Samples per Scan 256, 512, 1024, 2048, 4096, 8192, 16384
Operating Modes Continuous (time) or survey wheel (distance triggered) or point mode
Time Range 0-25,600 nanoseconds full scale, user-selectable.
Gain: manual adjustment
Standard Real-Time Filters Finite Impulse Response ( FIR) - Band Pass, Adaptive Background
Removal
Automatic Antenna Automatic recognition of all OKO antennas
Recognition
Languages
Russian, English, Chinese
Operating
Operating Temperature -20°C to 50°C external
Battery (2 pieces) Li-Pol 5 Ah / 14,8 V
Transmit Rate Up to 400 KH z
Input/Output
Available Ports Antenna inputs (one or two at a time), DC
power input, survey wheel connector, USB 2.0 port – 3 pcs
USB Host USB host with external keyboard support,
USB flash drive support and USB HUB support
Mechanical
Dimensions 3 5 x2 4x7 cm
Weight 5 kg (including battery)
Relative Humidity < 95% non-condensing
Storage Temperature - 3 0°C to 60°C

+7 (495) 641-2-641 [email protected] geotechru.com

ANTENNA UNITS OKO-3

Shielded antennas

Dual-Frequency antennas

Horn antennas

All-in-one GPR

TRITON-M (25/50/100 MHz)

All-in-one GPR
 SHIELDED ANTENNAS
GPR OKO

ANTENNA AB-90
Main frequency 90 МHz
Depth of scanning 16.0 m
Resolution 0.5 m
Dimensions 222x100x27 (cm)
Weight 37 Kg
Power consumption 8 Watts

ANTENNA AB-100M
Main frequency 100 МHz
Depth of scanning 14.0 m
Resolution 0.45 m
Dimensions 93x80x28 (cm)
Weight 16 Kg
Power consumption 6 Watts

ANTENNA AB-150M
Main frequency 150 МHz
Depth of scanning 12.0 m
Resolution 0.35 m
Dimensions 93x80x28 (cm)
Weight 16 Kg
Power consumption 6 Watts

ANTENNA AB-250M
Main frequency 250 МHz
Depth of scanning 8.0 m
Resolution 0.25 m
Dimensions 74x46x15 (cm)
Weight 10 Kg
Power consumption 6 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 SHIELDED ANTENNAS

ANTENNA AB-400M
Main frequency 400 МHz
Depth of scanning 5.0 m
Resolution 0.15 m
Dimensions 52x29x17 (cm)
Weight 4.5 Kg
Power consumption 6 Watts

ANTENNA AB-700M
Main frequency 700 МHz
Depth of scanning 3.0 m
Resolution 0.1 m
Dimensions 23x17x11 (cm)
Weight 2.2 Kg
Power consumption 3.6 Watts

ANTENNA AB-900M
Main frequency 900 МHz
Depth of scanning 2.5 m
Resolution 0.08 m
Dimensions 29x18.5x14 (cm)
Weight 2.3 Kg
Power consumption 3 Watts

ANTENNA AB-1200M
Main frequency 1200 МHz
Depth of scanning 1.5 m
Resolution 0.05 m
Dimensions 22x18x12 (cm)
Weight 0.8 Kg
Power consumption 3 Watts

ANTENNA AB-1700M
Main frequency 1700 МHz
Depth of scanning 1m
Resolution 0.03 m
Dimensions 22x18x12 (cm)
Weight 0.8 Kg
Power consumption 3 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 DUAL-FREQUENCY ANTENNAS
GPR OKO
The dual-frequency antennas are designed for automated location
of objects at different depths.

DUAL-FREQUENCY ANTENNA
AB-150/400M
Main frequency 150 and 400 МHz
Depth of scanning 12.0 and 5.0 m
Resolution 0.35 and 0.15 m
Dimensions 93x80x28 (cm)
Weight 16.5 Kg
Power consumption 8 Watts
DUAL-FREQUENCY ANTENNA
AB-250/700M
Main frequency 250 and 700 МHz
Depth of scanning 8.0 and 3.0 m
Resolution 0.25 and 0.1 m
Dimensions 74x46x15 (cm)
Weight 11 Kg
Power consumption 7.8 Watts

DUAL-FREQUENCY ANTENNA
AB-400/900M
Main frequency 400 and 900 МHz
Depth of scanning 5.0 and 2.5 m
Resolution 0.15 and 0.08 m
Dimensions 52x29x17 (cm)
Weight 4.8 Kg
Power consumption 6 Watts

DUAL-FREQUENCY ANTENNA
AB-700/2000R
Main frequency 700 and 2000 МHz
Depth of scanning 2 and 0.6 m
Resolution 0.1 and 0.02 m
Weight 4 Kg
Power consumption 6 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 HORN ANTENNAS

Horn antennas are ideal for tasks associated with the high-speed GPR
surveying of motorways and railways, which require ground air-launched
GPR location.

ANTENNA AB-400R
Main frequency 400 МHz
Depth of scanning 3.0 m
Resolution 0.1 m
Dimensions 73x57x37 (cm)
Weight 10 Kg
Power consumption 6 Watts

ANTENNA AB-1000R
Main frequency 1000 МHz
Depth of scanning 1.5 m
Resolution 0.04 m
Dimensions 63x20x53 (cm)
Weight 7.3 Kg
Power consumption 3 Watts

ANTENNA AB-1700R
Main frequency 1700 МHz
Depth of scanning 0.8 m
Resolution 0.03 m
Dimensions 20x19x17(cm)
Weight 1.2 Kg
Power consumption 3 Watts

ANTENNA AB-2000R
Main frequency 2000 МHz
Depth of scanning 0.6 m
Resolution 0.02 m
Dimensions 32x30x16(cm)
Weight 1.7 Kg
Power consumption 3 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 ALL-IN-ONE GPR SYSTEM
HORN ANTENNAS
GPR OKO

ANTENNA AB-2500R
Main frequency 2500 МHz
Depth of scanning 0.4 m
Resolution 0.015 m
Dimensions 32x30x16(cm)
Weight 1.7 Kg
Power consumption 3 Watts

DUAL-FREQUENCY ANTENNA
AB-700/2000R
Main frequency 700 and 2000 МHz
Depth of scanning 2.0 and 0.6 m
Resolution 0.2 and 0.02 m
Dimensions 60x21x29(cm)
Weight 4 Kg
Power consumption 6 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 ALL-IN-ONE GPR

The All-in-one GPR system is a GPR solution that combines

the antenna and the control unit into one enclosure
This new generation of GPR offers a quick and efficient way to prepare
a GPR for inspection. The All-in-one GPR system is connected with a laptop
via Ethernet cable or Wifi. Its low-cost GPR solutions are delivered
with all necessary accessories, such as an odometer, a power supply unit,
a charger and cables. Visual information is displayed on the laptop or PC tablet.
Our uniquely designed collapsible cart (for some models) makes
detection easy and convenient.

ALL-IN-ONE GPR
MG-250
Main frequency 150 and 400 МHz
Depth of scanning 12.0 and 5.0 m
Resolution 0.35 and 0.15 m
Dimensions 93x80x28 (cm)
Weight 16.5 Kg
Power consumption 8 Watts MG-250

ALL-IN-ONE GPR
MG-250/700
Main frequency 250 and 700 МHz
Depth of scanning 8.0 and 3.0 m
Resolution 0.25 and 0.1 m
Dimensions 74x45x15 (cm)
Weight 37 Kg
Power consumption 8 Watts
MG-250/700

ALL-IN-ONE GPR
MG-400
Main frequency 400 МHz
Depth of scanning 5m
Resolution 0.15 m
Dimensions 50x29x14 (cm)
Weight 5.5 Kg
Power consumption 6 Watts MG - 400
ALL-IN-ONE GPR
MG-400/900
Main frequency 400 and 900 МHz
Depth of scanning 5.0 and 2.5 m
Resolution 0.15 and 0.08 m
Dimensions 52x29x17 (cm)
Weight 6.5 Kg
Power consumption 15 Watts
MG-400/900

+7 (495) 641-2-641 [email protected] geotechru.com

TRITON-M (25/50/100 MHz) All-IN-ONE GPR
GPR OKO
The Triton-M antenna is an unshielded antenna with frequencies of
25/50/100 MHz.
The Triton M can be controlled from a PC or a tablet PC. The
connection between the monoblock and the PC (tablet PC) is via Wi-Fi.

Features:
3 times faster GPR surveys and improved data quality.

unshielded antenna consists of 5 sections, it makes possible to easy

change the central frequency (25 or 50 or 100 Mhz)

geophysical research for linear objects and engineering structures

increasing the depth of work

GPR surveys over rough terrain and in difficult operating conditions

connecting via Wi-Fi

SPECIFICATIONS

Center frequency 100/50 МHz

Maximum sounding depth 14.0/18.0m
Resolution 0.5/1 m
Case dimensions 113x41x16 (cm)
Dimensions 120x215x26x12 (cm)
Weight in a case 16.3 Kg
Weight (assembled) 4.85/8.0 Kg
Power consumption 3.6 Watts

+7 (495) 641-2-641 [email protected] geotechru.com

 SPECIAL SOLUTIONS

Construction Scan

Underwater GPR

Ice thickness Sensor

GPR for high-speed

higway monitoring

Multichannel GPR complex

for railway examination

GeoCart 2D
 CONSTRUCTION SCAN
GPR OKO
CS-1700 (2500)

The Construction Scan is a portable all-in-one GPR solution designed

for the automated localizing o defects in a wide variety of wood, brick
and reinforced concrete structures, in depths up to 0, 6 and 1m,
in real time.
Application:
Detection and location of different defects in reinforced concrete
(cells, cavities, foreign inclusions, cracks and layering)
Determination of reinforcement specification size, occurrence depth
and degree of corrosion
Detection of buried wiring, cables and communications lines
Detection of plastic and metal pipelines
Detection of heterogeneities, anomalies and other buried
in solid environment (which wood, brick, reinforced concrete,
building constructions, soil, etc)
Discovering of ventilation and communication channels
Detection of shelters and covered-up holes

Features:
All-in-one GPR system
5″ colour display
3D visualization
Built-in USB interface
Internal 2 GB Flash memory card
Detachable SD-card
Guiding laser
Data collection grids (3D system)
Built-in bar code reader
Languages (Russian, English, Chinese)
Quickly-detachable Lithium-ion battery 15V

+7 (495) 641-2-641 [email protected] geotechru.com

 UNDERWATER ANTENNA
AB-700M3P

Search and localization of various defects in the underwater

and surface parts of reinforced concrete structures;

Determination of reinforcement, reinforcement pitch,

and cover depth;

Localization of waterlogged areas behind concrete;

Detection of voids behind lining space.

Topographic referencing via differential GPS;

Data export to GIS

Immersion depth in water up to 10 meters;

Sounding depth of concrete up to 2 meters;

Features:
Underwater shielded antenna with a center frequency of 700 MHz;
Immersion depth in water up to 10 meters;
Sounding depth of concrete up to 2 meters;
Topographic referencing via differential GPS;
Data export to GIS.

Depth up to 10 m
Main frequency 700 30% MHz
Maximum sounding depth 2.0 m
Resolution 10 cm
Dimensions 270x60x120 mm
Weight 2.2 kg

+7 (495) 641-2-641 [email protected] geotechru.com

 Ice Thickness Sensor
GPR OKO LD-400

The LD-400 hardware and software complex is developed on the basis of the OKO-3 series
GPR complex with the MG-400 antenna for the prompt determination of ice thickness and
structure, localization of inhomogeneity, cracks, and other defects within the ice mass in real
time. The device can be mounted on any vehicle (using an external antenna bracket) with a
separation from the surface of 0.5 - 1.0 m

Features:
ice thickness measurement range:
fresh ice - from 0.2 to 8 meters
sea ice - from 0.2 to 1.5 meters
the operator receives visual information about ice thickness, standard load, cracks, and
inhomogeneities within the array in real time
high accuracy and low noise level
high efficiency in thawing, freezing, salinity conditions
referencing in a common coordinate system to determine the location of the object under study
(GPS, Glonass);
operation with a separation from the surface of 1-1.5 m
tested in conditions of arctic expeditions

Technical specification:
Center frequency 400 MHz
Resolution 0.10 m
Operating temperature from -50° to +50 °С
Dimensions 0.5 х 0.3 х 0.15 m
Weight 5.5 kg
Power consumption 6W

Application:
safety control during the movement of vehicles and people on ice crossings
monitoring of ice thickness during winter fishing, extreme driving on ice, etc.
obtaining data for forecasting the pre-flood period

+7 (495) 641-2-641 [email protected] geotechru.com

 Air
Snow
The ice thickness
Ice
Ice Thickness Sensor Water
LD-1200

The LD-1200 Ice Thickness Sensor is designed for non-contact and contact
measurement of the thickness of fresh ice, detection of dangerous places
(cracks, scours, voids) in real time. It has a convenient, lightweight, portable
design for pedestrian operation: one-handed operation, ice thickness
measurement range of 0.05 - 2.0 m
Features:
convenient, lightweight, portable design for pedestrian operation:
one-handed operation, ice thickness measurement range of 0.05 - 2.0 m
real-time display of a radarogram with the interfaces between environments
(air, snow, ice), ice thickness, as well as the permissible standard load on
ice
fast and accurate identification of dangerous places - cracks, scours, voids
smooth operation at low temperatures (up to -40 ºС)
referencing in a common coordinate system to determine the location of the
object under study (GPS, Glonass)
operation with a separation from the surface of 0.5 - 1 m
time of continuous work - at least 8 hours
device weight - 2 kg

Technical specification:
Ice thickness measurement range 0.05 - 2.0 m
Resolution at least 0.05 m
Weight up to 2.0 kg
Weight in the carrying case up to 10.0 kg
Power supplies: (NiMH)
• battery power supply unit BP-3,8/12I 1
• battery power supply unit BPB (type AA-1.5V) 1
Running time at least 8 h
Operating temperature from -40°С to +50 °С
Preparation time for work up to 1 min.
Internal memory at least 2 GB
Carrying case dimensions 650x500x240 mm

Application:
safety control during the movement of vehicles and people on ice crossings
monitoring of ice thickness during winter fishing, extreme driving on ice, etc.
obtaining data for forecasting the pre-flood period

+7 (495) 641-2-641 [email protected] geotechru.com

 Modification on a drone
GPR OKO LD-400

Safe remote measurement

of ice thickness
Technical specification:
The measured thickness of ice in the hover mode at a height of 5-10 meters, not less than 2 m
Separation from the surface 5-10 m
Center frequency (UWB signals) 400 MHz
Sounding depth:
sea ice from 0.2 to 2.5 m
fresh ice from 0.2 to 8.0 m
Features:
the operator receives visual information about ice thickness, standard load, cracks, and
inhomogeneities within the array in real time
high accuracy and low noise level
high efficiency in thawing, freezing, salinity conditions
referencing in a common coordinate system to determine the location of the object under study
(GPS, Glonass)
operation with a separation from the surface of 5-10 m
tested in conditions of arctic expeditions
no analogues in the world
Flight trajectory Radar altitude chart

A separation
from the surface
Ice thickness
30 sm

Applications:
safety control during the movement of vehicles and people on ice crossings
monitoring of ice thickness during winter fishing, extreme driving on ice, etc.
obtaining data for forecasting the pre-flood period

+7 (495) 641-2-641 [email protected] geotechru.com

 GPR SYSTEM FOR HIGH-SPEED HIGHWAY MONITORING

The OKO-3 GPR Road Set is designed for non-destructive inspection and analysis
of the road structure. The device uses special horn antennae (400-2500MHz) located above
ground level and fixed to a vehicle by an antenna bracket. The road complex offers users
the single-channel and multi-channel solutions for high resolution surveys at speed
up to 80 km/h.

AB-700/2000R
Аntenna

Application
Engineering-geophysical surveys for highway and overpass construction

Determination of the thickness of road pavement structural layers

Detection of subsidence
Detection of non-solid and watered zones
Study of engineering-geological conditions of the zones liable to deformation
Study of dangerous engineering geological processes:
Landslides, floating earth, karst phenomena
Check of the highway pavement structure compliance with project documentation

Features:
high-speed multi-channel control unit
number of channels: up to six (up to 6 bore hole
profiles simultaneously) reinforcing
antenna frequency: from 150MHz to drill sample
asphalt-concrete
2500MHz
maximum survey speed: up to 80 km/h
detection depth: up to 8m concrete

creating a 3D model sand

GPS integration and gravel

fill-up ground

+7 (495) 641-2-641 [email protected] geotechru.com

 MULTICHANNEL GPR COMPLEX FOR RAILWAY EVALUATION
GPR OKO
High-speed multichannel GPR complex (survey speed: up to 150 km/hour).

broken-stone ballast
sand and gravel
clay loam

FEATURES
High speed multi-channel control unit
Number of channels: Up to six profiles simultaneously
Wide variety of antenna frequencies: from 150MHz up to 2500 MHz
Rapid maximum survey speed: Up to 150 km/h
Deep detection depth: Up to 8m
Ability to create 3D model of ballast
GPS integration
Automated data processing

+7 (495) 641-2-641 [email protected] geotechru.com

 MULTICHANNEL GPR COMPLEX
FOR RAILWAY EVALUATION

SPECIFICATIONS
Antennas
AB-2000RS (2000 MHz central frequency)
AB-1700RS (1700 MHz central frequency)
AB-10 00RS (1000 MHz central frequency)
AB- 400RS ( 400 MHz central frequency)
AB-250S (250 MHz central frequency)
AB-150S (150 MHz central frequency)
The maximum depth of detection
AB- 2000RS - 0,6 m
AB-17 00RS - 0,8 m
AB-10 00RS - 1,5 m
AB- 400RS - 2 ,5 m
AB-150S - 8 m
Scan rate for each channel 400 scan/sec
(512 samples per scan)
High repetition frequency up to 400 kHz
Power supply 12-15V
Resolution 0,03-0,35 m
Maximum scan length unlimited
Operating temperature -30°C up to +50°C
Environmental IP65
APPLICATION
Determination of the railway embankment width and structure
content
Allocation of subsidence in the ballastand natural bed layers
Determination of the natural bed
Mapping underground pipelines crossing railway
embankment
Control of conformation of railway embankment structure
tothe project documentation

Subsidence
in base layer

+7 (495) 641-2-641 [email protected] geotechru.com

 GEOCART 2D
GPR OKO
GeoCart 2D is designed to locate the depth and position of utilities
such as pipes, cables, reservoirs and drainage systems in a variety of
soils at different depths. CartScan software allows its user to display
all information on Google Earth.

The systems combines:

Dual frequency antenna
Removable wheels with two integrated odometers
GPS-receiver
Lightweight rugged trolley
Power supply unit
Line locator

Features
Dual-frequency antenna (250 and 700 MH z) for
deep and shallow survey in single scan
Two odometers embedded in the wheels for more
accurate marking
Real time data collection
Enhanced 3D capabilities
Automatic GPS integration
Google Earth Integration

GeoCart 2D is a turnkey GPR solution for

utilities mapning.The systems
consists of dual-frequency antenna (250 and
700 MH z), GPS -receiver, and two odometers
built into the wheels of trolley. By using data
collected from the odometers and GPS -
receiver simultaneously, the user can locate
and mark utilities accurately and quickly.

The antenna with dual frequencies of 250 and 700 MH z

provides GPR data at depths of 8 and 3 meters
simultaneously or separately. The special software
CartScan allows the user to visualize 3D data, and see
all communicated information on Google Earth.

+7 (495) 641-2-641 [email protected] geotechru.com

SOFTWARE

CartScan

GeoScan32

ArmScan

Analysis 7

Analysis 7. Asphalt module

 CARTSCAN
GPR OKO
Special software allows the user to visualize 3D data and see
information about utilities on Google Earth. CartScan Software
is Windows™ based.

Features
Scanning with data saved to GPR format file
Displays current position on map
Calibration of two wheel trolley geometry parameter
Storage sound marks
Storage photo marks
Viewing collected files in two channel mode, viewing each
channel separately
Viewing movement path on map during collected files
preview
Viewing photo marks while looking through collected files
Creating 3D profile
Data processing during collected files preview

The software set consists :

Scanning
Options
Data processing
Loading map
Track Editor

Scanning (active when the antenna and geo location

unit (GLU ) are connected – work begins in scan mode).
If operation without GLU is ordered in settings, the
button will be active if only single antenna is available.
Options – software setting parameters change.
Data processing – operation with data file, obtained
during scanning mode operation.
Track editor – tracks (move trajectory) shape and
location editing obtained during scanning, and which
will be included in the file.
Exit - Shutdown work with the software package.
Loading map (active only when Internet connection is
available) - download maps to buffer allows for use
without Internet connection.

+7 (495) 641-2-641 [email protected] geotechru.com

 GEOSCAN32

GeoScan32 software is designed for controlling a subsurface

sounding device (GPR) and subsequent processing and
visualisation of information obtained during sounding.

A 3D image can take the form of intersecting planes or a cube.

In the 3D visualisation mode, users can change the gain profile,
contrast, properties of the 3D block and redefine colouring.

Features:
Collection of GPR data obtained using OKO GPR equipment
in continuous mode, mode by movement (using movement
sensors) and in mode by steps;
Data visualisation during survey;
Interactive determination of layer velocities and depths of local
objects during data processing;
Layered processing;
Processing of area survey data;
Considering terrain data;
Editing tracks;
Working with the map Time zero offset.

Working with the map consists in positioning the map in a given area, changing the scale and
choosing the display type.

GPR surveys often reveal fairly extended and homogeneous zones. They can be represented as soil
layers with individual values of the propagation velocity of an electromagnetic wave, which is
determined by the dielectric constant of the medium.

Having determined the permittivity at some point of the layer, it can be applied to the entire layer. In
this case, it becomes possible to bring the GPR profile image in line with its geometric dimensions.
This can be very useful in road construction and many other fields.

Therefore, GeoScan32 software provides a separate mode that allows an operator to draw layers on
the profile, change their properties and export layer data for further processing in Autocad or similar
programs.
Layered interpretation of profiles

+7 (495) 641-2-641 [email protected] geotechru.com

 ARMSCAN
GPR OKO
ArmScan software is designed to process GPR
data obtained by scanning building structures,
concrete slabs, walls, and ceilings; to determine
the position of reinforcing bars in plan and in
depth; to build a 3D model of a reinforced
concrete structure based on the results of GPR
scanning.

3D visualisation of the received data. Sections

in any planes. Display of detected line objects.
Depth scale and captions for marks.

CS-1700 3D CS-2500 3D

CS-2500 gives more detailed image of the structure.

+7 (495) 641-2-641 [email protected] geotechru.com

 ANALYSIS 7

The Analysis-7 software complex is one of the latest developments.

Analysis-7 is primarily intended for working with data received by
multi-channel GPR complexes OKO for railways. The latest version of
the software implements the possibility of automatic processing and
interpretation of radargrams, analysis of the thickness of structural
layers, moisture and slope. Automatic generation of reports is also
available.

Features:
Binding to the route on the map and on frames from CCTV cameras,

Automatic tracing of layers,

Layered data interpretation,

Automatic thickness analysis,

Automatic detection of waterlogged areas,

Automatic calculation of an embankment slope,

Building a 3D model taking into account the relief,

Fully automatic processing and report generation.

+7 (495) 641-2-641 [email protected] geotechru.com

 ANALYSIS 7. ASPHALT MODULE
GPR OKO

Analysis-7 software complex. The Asphalt module is one of the

newest developments. It is intended primarily for working with data
obtained using the OKO-3 GPR. The latest version of the software
implements the following features: automatic processing and
interpretation of radargrams, analysis of the thickness of structural
layers, moisture and slope. Automatic generation of reports is also
available.

Features:
Comparison of the thicknesses of the layers recorded on the
radargram with the restrictions on the minimum and maximum
thicknesses specified for them

Comparison with drilling data

Delineating of waterlogged areas

Semi-automatic picking of the bottom of the asphalt concrete layer

+7 (495) 641-2-641 [email protected] geotechru.com

GEOTECH