CONTENTS

FUNCTIONS & FEATURES..............................................................................................................................................................1

STANDARD ACCESSORIES............................................................................................................................................................1

INSTALLATION.................................................................................................................................................................................2

GETTING ACQUAINTED..................................................................................................................................................................3

HOW TO USE YOUR RADIO...........................................................................................................................................................5

KEYPAD FUNCTION........................................................................................................................................................................5

CHANNEL FUNCTION MENU OPERATOIN....................................................................................................................................7

PUBLIC DATA FUNCTION MENU OPERATION.............................................................................................................................7

BACKGROUND FUNCTION MENU OPERATION...........................................................................................................................8

SPECIFICATIONS............................................................................................................................................................................10
 FUNCTIONS & FEATURES STANDARD ACCESSORIES
111 Big LCD displays frequency and all kinds of information
222 FM、AM、USB、LSB 、PA mode
333 Frequency Tuning Step 100Hz, 1KHz, 10KHz, 100KHz, 1MHz
444 ± 1.5KHz Clarifier
555 Flexiable menu function and PC programming software
666 ECHO Function
777 SQ, ASQ Function (FM and AM mode only) Radio Microphone Install bracket
888 RF GAIN Adjustment
999 RF PWR Adjustment
1111SCAN Function
1111Programmable RB Function
1111NB/ANL Function
1111DW DUAL-WATCH Function Screws Pads Adjusting screws 1
1111BEEP Voice Prompt
1111+10KHZ Function
1111SWR、S/RF function
1111TOT function
1111HI-CUT Function
1111EMG CALL Microphone Hanger non-slip mat Fuse(15A 250V)
2222SWR PROTECTION
2222Power Supply Voltage Protection
2222Key-Lock Function
2222Seven (7) Color LCD Display
2222Six(6) Groups Memory Channel
2222CTCSS/DCS Code(Optional)
2222DTMF Function
 INSTALLATION
Choose the most appropriate setting from a simple and practical point of
view. Your radio should not interfere with the driver or crash the driver's
knee or leg when rush brake.
111 Using the self-tapping screws and pads(2 sets) to fix the bracket.
222 Put the Non-slip mat on the 2 ends of the bracket and put in the
radio.Then insert the adjusting screws and check carefull each WARNING:
screws, make sure the screws and machine will not loose when the ▲ Connect antenna firstly before transmiting, or it might damage the
car shaking. radio.
333 Choose suitable angle by the 3 screw holes in the two ends of ▲ To avoid the risk of fire, electric shock, radio damage, all base
bracket. station shall equip of lightning protector
▲ Be sure choose a matching antenna, you may enquiry our dealers.
333 The position of antenna can be put as following example:

POWER CONNECTION
This radio adopt 13.8V power supply, never connect it to 24V battery,
ANTENNA INSTALLATION
And the 13.8V car battery shall with sufficient current, or the LCD will
Before using this radio, please install a high efficent and harmonious become dark and Transmit power will drop down.
adjusted CB antenna, suitable antenna type and correct installation
111 Connect positive red power cable with the + terminal of the battery.
will bring excellent communication.
222 Connect negative black power cable with the - terminal of the
To match with the radio, the antenna and cable shall with
battery.
characteristic impedance of 50ohm, or the antenna system will not
efficient enough and will disturb TV, radio or other electronics. ▲ We suggest not use cigar lighter as it often bring down the voltage.
▲ Locate the power cable away from high temperature,moisture,
111 Screw the antenna connector into the antenna jack.
portfire and cable insulator.
222 Grounding the antenna system to ensure best performance of
this radio. ▲ Use a full power cable even it is longer than need, do not take off
the fuse holder from the cable.
Replacing Fuse GETTING ACQUAINTED
This radio adopt 15A, 250V fuse. Front Panel
If the fuse blows, determine the reason, then correct the problem.
After the problem is resolved, replace the fuse. If newly installed 9 10 11 12 1 2 3 4
fuses continue to blow, disconnect the power cable and contact your
autho-rized dealer or an authorized servicecenter.
111 Pull the two fuse cover in difference direction and open it.
15 14
222 Replace the broke fuse with good one, and close the fuse holder.
333 Be sure to use suggested fuse, or it might damage the radio. 16
EMG

13 5 6 17 7 8

No. Key Functions

1 MEM Use, store or delete memory channel
Install Microphone Hanger 2 MODE Switch mode: FM、AM、USB、LSB、PA
3
Choose a ideal location which will not interfere the driver. Using 3 BAND Switch band: A-I
supplied self-tapping screws and pads(2 sets) to fix the hanger 4 FRQ Switch between channel mode and frequency mode
5 MENU Function Menu key
6 SCAN Scan, Scan add, Scan delete
Install External Speaker
7 DW Dual-watch scan, Dual-watch setup
If use an external speaker, please choose 8 ohm speaker with
8 EMG Emergy Channel; Keypad lock.
3.5mm mono band (doulbe cable) plug.
111 Locate the external speaker in a suitable place. 9 PWR RF Power Control

222 Plug into the speaker jack. 10 RFG RF Gain Control

11 SQ Squelch Control
12 CLAR SSB Clarifier switch
13 VOL/OFF Power On/Off; Volume Control.
14 CH Channel Switch, Push key.
15 RX/TX Indicator
16 Microphone Jack
17 LCD Display
 Rear Panel LCD Display
20 19 18
1 5 7 6 9 8 11 10 12 13 15 14 17 16 18
ANT
EXT SP

DATA
19
2 22
3 23
4

20 21
18 PC Cable Jack 1 Appears when press MENU key.
19 External Speaker Jack 2 Appears when adjust SSB clarifier frequency.
20 Antenna Jack 3 Appears when use ASQ.
4 Appears during scan function.
5 Indication of working mode.
Microphone 6 Appears when set with CTCSS code.
7 Appears when set with DCS code.
4 Channel Down Channel UP
8 Appears when Beep voice is ON.
9 Appears when RB function is ON.
PTT
10 Appears when Dual-watch function is ON.
Connector 11 Appears when adjust Noise Blanker is ON.
Mic 12 Appears during transmiting.
13 Indiation of working band.
14 Appears when Hi-cut function is ON.
15 Appears when using Emergency channel.
16 Appears when Echo function is ON.
17 Appears when the Keypad lock function is ON.
18 Appears when +10Khz function is ON.
19 Indication of SWR level.
Microphone cable 20 Display of frequency and channel.
21 Appears when using memory channels
22 Appears when repeater function is ON.

23 Display of TX/RX Signal strength.

HOW TO USE YOUR RADIO Channel Selection
When radio in channel mode, turn channel knob to select desired
OFF/ON Radio
channel. Clockwise to increase, anti-clockwise to reduce channel.
111 Turn VOL clockwise to switch on the radio, the radio emit a beep.
When the LCD displays frequency or channel, the radio is on. Note: In channel display mode, each press【PUSH】key will
222 Turn VOL anti-clockwise to switch off the radio, the radio is OFF increase the frequency by 10 times of channel step size.
when hear Ka Ta from the switch.
Frequency control
Volume Control 111 In frequency mode, press【PUSH】key, then you can adjust
When the radio is turned on, turn VOL clockwise will increase the frequency for present channel.
volume, turn VOL anti-clockwise will reduce the volume. The LCD 222 When the frequency is flashing, turn CH clockwise to increase
displays VOL: XX (XX stands for the volume level, total 1-36 levels). frequency, anti-clockwise to reduce frequency.
Note: Adjust the volume during communication to get suitable level. 333 When the frequency is flashing, press【PUSH】again to adjust
frequency step size.
RF Power Control
When the radio is transmitting, turn PWR outer shaft to adjust power. 5
Turn it clockwise to increase power, anti-clockwise to reduce power.
KEYPAD FUNCTION
RF Gain Control
【MEM】
When the radio is receiving, turn RFG inner shaft to adjust RF gain.
Turn it clockwise to increase gain, anti-clockwise to reduce gain. Using memory channel:
111 Short press【MEM】to enter memory channel, turn CH to
SQUELCH Control choose memory channel.M1-M6, Total 6 memory channels.
When the radio is standby, turn SQ outter shaft clockwise to adjust 222 Short press【MEM】again to exit memory channel mode.
squelch level. The LCD displays SQ: XX. (XX stands for the squelch Store/Delete memory channel:
level, total 1-36 levels). 111 Store memory channel:
When the radio is not in memory channel mode, choose the
SSB Clarifier control channel to be stored, and hold【MEM】enter storage mode,
When the radio is transmitting or receiving, turn CLAR inner shaft to the channel number flashes, Turn Channel switch to choose
adjust USB/LSB TX or RX frequency. Turn it clockwise to increase the location to be stored (M1-M6), then hold【MEM】until the
frequency, anti-clockwise to reduce frequency. flashing channel number disappear, the storage is done.
 222 Delete memory channel: Add/delete scan list
In channel mode, hold【MEM】for over 2 seconds, the memory In channel mode, Long press【SCAN】for over 2 seconds will add
channel number flashes, turn the CH switch to choose the or delete present channel from scan list.
memory to be deleted. Then hold【MEM】until the flashing 111 When LCD displays "SC", present channel added to scan list.
channel number disappear, the delete is done. 222 When LCD does not displays "SC", present channel is not
added to scan list.
【MODE】 Note: This function is equal the operation in Channel data
Short press【MODE】to choose mode FM-AM-USB-LSB-PA. function No.05 menu.

【BAND】 【DW】
Short press【BAND】to choose band A-B-C-D-E-F-G-H-I. Dual-Watch function
111 Short press【DW】to turn on Dual watch, LCD displays "DW";
【FRQ】 222 Short press【DW】again or press PTT to exit DW mode;
Dual-Watch channel setup
Short press【FRQ】to switch between frequency display mode and
channel display mode. 111 Choose first Dual-Watch channel.
6
222 Hold【DW】for 2 seconds, LCD displays "DW";
【MENU】 333 Turn Channel switch to choose second dual watch channel.
Long press DW again to store and exit.
111 Short press【MENU】, the top left of LCD display "F", Press
【PUSH】 to enter channel function menu list.
222 Long press 【MENU】for 2 seconds to enter Background 【EMG】
Function menu. Choose EMG channel:
Short press【EMG】 to use Emergency channel, LCD displays "EMG".
【SCAN】 111 Short press【EMG】once to choose CH9;
Scan function 222 Short press【EMG】again to choose CH19;
111 Short press【SCAN】to start scan function, "SC" flashes in 333 Short press【EMG】thrice to return to last normal channel.
the LCD. Keypad Lock Function:
222 In scan mode, Turn Channel switch will change scan 111 Long press【EMG】to lock keys, LCD displays " ";
direction.
222 Long press【EMG】again to unlock the keys.
333 Short press【SCAN】again to exit scan.
Note: When this function is turned on, only PTT button is valid.
CHANNEL FUNCTION MENU OPERATION
ADD: LCD displays "SC", present
111 Press【MENU】, the top left of LCD display "F", Press【PUSH】
to enter menu list. channel is added to scan list.
222 Turn Channel switch to find No.1- No.5 menus. Add/delete DEL: LCD does not display "SC",
4
Scan list present channel is not added
333 Press【PUSH】to choose the menu.
444 Turn Channel switch to choose wanted value. to scan list.
555 Press【PUSH】to return to previous menu, press any other key Default: OFF
or wait 5 seconds, the setting will be stored and exit.
OFF: Choose independent channel
No. Function LCD Display Values and Descriptions menu;
OFF: Shut busy channel lockout ON: Choose public channel menu;
function; Default: ON
Busy Channel 5 Public Data
1 ON: Open busy channel lockout Note: If choose OFF, The hidden
Lockout channel menu 6-11 will appear.
function;
Default: OFF. This 6 menus are same as the
6 menus in Public data menus.
REP+: Open offset direction 7
function, TX frequency> RX Note: Channel funciton menu is used to edit the setting for current
frequency;
Offset channel.
2 REP-: Open offset direction function,
Direction
RX frequency> TX frequency;
OFF: Shut offset direction function
PUBLIC DATA FUNCTION MENU OPERATION
Default: OFF.
111 Hold【PUSH】for 2 seconds to enter menu list;
CTCSS: 67.0~250.3Hz, Total 38
222 Turn Channel switch to find menu 1-6;
groups;
DCS: D023N~D754N, Total 104
333 Press【PUSH】to choose the menu;
groups; 444 Turn channel switch to choose wanted value.
3 CTCSS/DCS OFF: Shut CTCSS/DCS code 555 Press【PUSH】to return to previous menu, press any other key
function. or wait 5 seconds, the setting will be stored and exit.
Default: OFF
Note: This function is available only
when install Optional CTC board.
 No. Function LCD Display Values and Descriptions BACKGROUND FUNCTION MENU OPERATION
111 Hold【MENU】for 2 seconds to enter menu list;
OFF: Shut HI-CUT function;
1 Hi-cut ON: Open HI-CUT function; 222 Turn Channel switch to ind menu No.1 to No.15;
Default : OFF. 333 Press【PUSH】to choose the menu;
444 Turn channel switch to choose wanted value;
OFF: Shut NB/ANL function; 555 Press【PUSH】to return to previous menu, press any other key
2 NB/ANL ON: Open NB/ANL function;
or wait 5 seconds, the setting will be stored and exit.
Default : ON.
No. Function LCD Display Values and Descriptions
OFF: Shut ECHO function; OFF: Shut BEEP function;
3 ECHO ON: Open ECHO function; 1 BEEP ON: Open BEEP function;
Default : OFF Default: ON.
OFF: Displays TX frequency when
OFF: Shut +10KHz function; TX;
4 10KHz ON: Open +10KHz function;
SWR: Displays SWR value when TX
Default: OFF LCD display
8 2 TOT: displays TOT remain time
in TX mode
when TX;
OFF- 5, Total 6 groups. DC: Displays voltage when TX;
5 ROGER Default: OFF,Off means shut Default: OFF.
off Roger.
1-36, Total 36 levels available.
BOT: Press PTT to send DTMF 3 Mic Gain
Default: 30.
encode;
EOT: Release PTT to send
DTMF encode; Monitor 1-32, OFF, Total 33 levels
CALL: Hold PTT+EMG to send 4 available;
DTMF PTT Gain Default: OFF (Shut NOG function)
6 DTMF encode;
ID
Note: If the M1-M16 storage 1-600s, OFF, Total 10minutes
has no PTT ID, DTMF function
5 TOT available;
is defaulted OFF. Users able to
Default: 180S (Shut TOT function)
choose the DTMF group only
when programmed with code. SWR OFF: Shut SWR function;
6 ON: Open SWR function;
Note: Public function menu offer one-time setting for all channels. Protection Default: ON
 OFF: Shut voltage protection S TIME: DTMF transmit time;
function; FDELAY: First digital time;
Voltage
7 ON: Open voltage protection C TIME: Pre-carrier time;
Protection function; *# TIME: *and # delay time;
Default: ON D CODE: D code setting time;
TXDIS: Display setting for DTMF
SQ: SQ scan function; transmit;
8 Scan Type TI: Time scan function; DTMF MEM: DTMF encode storage
Default: SQ 14 list;
Encode Note: In the DTMF encode
OFF: Shut frequency adjustment storage list (M1-M16), press
R: Open RX frequency PUSH to edit DTMF code, then
adjustment; turn channel knob to choose
T: Open TX frequency desired value, press PUSH
9 Clarifier
adjustment; again to edit next list, after finish
RT: Open TX/RX frequency setting, hold PUSH to store it
adjustment; and back to main menu.
Default: R
OPT: All function setup resume 9
WHITE,BLUE,GREEEN, default;
10 Backight YELLOW, RED,PURPLE,CYAN 15 Reset ALL: All channels and setup
Default: WHITE resume default;
Default: OPT
REP Frequency Range: 100Hz-5MHz
11
frequency Default: 100KHz

CHAN: Choose to adjust channel

Channel FREQ: Choose to adjust
12
Switch Setup frequency
Default: FREQ

01-09, total 9 level available

13 ASQ level
Default: 05
 SPECIFICATIONS
GENERAL RECEIVER
Frequency Range 28.000-29.700MHz(Programmable)
SSB: 0.25μV for 10dB(S+N)/N
Frequency Band A/B/C/D/E/F/G/H/I
AM:1.0μV for 10dB(S+N)/N
Channel 40channels(programmable)in each band Sensitivity
FM: 1.0μV for 20 dB (S+N)/N
Frequency Control Phase-Locked-Loop Synthesizer (All at greater than 1/2 watt of audio output)
Frequency Step 100Hz、1KHz、10KHz、100KHz、1MHz
Adjacent-Channel
Frequency Tolerance ±5.0 ppm AM/FM: 60dB SSB: 70dB
Selectivity
Temperature Range -20℃to +50℃
Microphone with push-to-talk /UP/DN and coiled cord Image Rejection More than 65dB
Input Voltage 13.8V AM/FM: 10.695MHz 1st IF, 455KHz 2nd IF
Dimensions (in mm) 245(L) x 158(W) x 48(H) IF Frequency
SSB: 10.695MHz
Weight 1.5kg
Antenna Connector UHF,SO239 RF Gain Control 45dB adjustable for optimum signal reception
10
Automatic Gain Less than 10dB change in audio output for
Control(AGC) inputs from 10 to 100,000 microvolt.
TRANSMITTER
Adjustable; threshold less than 1.0μV.
Power Output AM: 15W / FM:45W / SSB: 60W(PEP) Squelch
Automatic Squelch Control(only AM/FM)1.0μV
Drain 12A(with modulation)
Audio Output Power 3 watts into 8 ohms
Modulation FM/AM/USB/LSB
Inter-modulation SSB: 3rd order, more than -25dB; 5th order, Frequency Response AM/FM: 300 to 3000Hz SSB: 450 to 2500Hz
Distortion more than -35dB
Built-in Speaker 8 ohms, round.
SSB Carrier
55dB External Speaker(Not 8 ohms; disables internal speaker when
Suppression
Unwanted Sideband 50dB Supplied) connected.
AM/FM: 300 to 3000Hz
Frequency Response
SSB: 450 to 2500Hz
Output Impedance 50ohms, unbalanced
A2.141005