Colour Television Chassis

43PFT6100S/67
49PFT6100S/67
5PFT6100S/67


Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Series name 43PFT6100 49PFT6100 55PFT6100
Set Product Manager
Set Product Manager in outsourcing
company
E-mail address of main contact in
outsourcing company
Set Project Manager
Status
CR (yyyyww) of leading set
Platform/Chipset T8E3-6A628 DVB-T2 T8E3-6A628 DVB-T2 T8E3-6A628 DVB-T2
Processor type (CPU) / GPU

Picture/Display

RC

Backlight Type (Panel Supplier) DLED DLED DLED

Diagonal Screen Size 42.51" 48.5" 54.64”
Perfect Motion Rate 1920×1080@60Hz 1920×1080@60Hz 1920×1080@60Hz
Panel Frequency (Native) 60HZ 60HZ 60HZ
Chasis Frequency 60HZ 60HZ 60HZ
Backlight Dimming PWM PWM PWM
Scanning Segments (amount) 48.25--863.25MHZ 48.25--863.25MHZ 48.25--863.25MHZ
Panel Resolution 1920*1080 1920*1080 1920*1080
Aspect ratio 16:9 16:9 16:9
Brightness (Home Vivid Mode) cd/m² Min：220cd/m2 ，Typ:260cd/m2 Min：280cd/m2 ， Min:300cd/m2；
Panel contrast ratio 1200:1 Typ:330cd/m2
1200:1 Typ:350cd/m2
1200：1
Viewing Angle - H (L+R) 178° 178° 176°
Viewing Angle - V 178° 178° 176°
Response Time (ms) 8ms 9ms 6ms
Analog + PWM dimming YES YES YES
2D/3D Logic (2D/3D Active/3D 2D 2D 2D
Passive
Color )
Gamut NTSC 66% NTSC 65% NTSC 68%
PQ engine Digital Crystal Clear Digital Crystal Clear Digital Crystal Clear
PQ Resolution N/A N/A N/A
Directional Super Resolution (on 2D
N/A N/A N/A
& 3D)
Improved 3D Super Resolution N/A N/A N/A
ISF Color Management N/A N/A N/A
Digital Natural Motion (2D/3D ) N/A N/A N/A
Perfect Natural Motion (2D/3D ) N/A N/A N/A
2D to 3D Conversion N/A N/A N/A
3D Depth adjustment (Auto/Offset) N/A N/A N/A
Auto 3D Detection N/A N/A N/A
Micro Dimming Demo N/A N/A N/A
Micro Dimming mode N/A N/A N/A
Dual View (2 Player Full Screen
N/A N/A N/A
Gaming/Video) 双屏
Supported Display Resolution 720*400@70HZ 720*400@70HZ 720*400@70HZ
(Computer Inputs) 640*480@60HZ 640*480@60HZ 640*480@60HZ
800*600@60HZ 800*600@60HZ 800*600@60HZ
1024*768@60HZ 1024*768@60HZ 1024*768@60HZ
1360*768@60HZ 1360*768@60HZ 1360*768@60HZ
1280*720@60HZ 1280*720@60HZ 1280*720@60HZ
1280*960@60HZ 1280*960@60HZ 1280*960@60HZ
1280*1024@60HZ 1280*1024@60HZ 1280*1024@60HZ
1600*900@60HZ 1600*900@60HZ 1600*900@60HZ
1920*1080@60HZ 1920*1080@60HZ 1920*1080@60HZ

1
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Supported Display Resolution (Video 480i, 480p,576i, 480i, 480p,576i, 480i, 480p,576i,
Inputs) 576p,720p,1080i,1080p(24/25/30 576p,720p,1080i,1080p(24/25 576p,720p,1080i,1080p(24/25
/50/60Hz) /30/50/60Hz) /30/50/60Hz)
Brightness (Shop Vivid mode: 10% YES(1% boost) YES(1% boost) YES(1% boost)
boost)
Pixel Plus Link (I/II/III) N/A N/A N/A
Active Control N/A N/A N/A
Local Contrast N/A N/A N/A
"UHD Display" - logo (Industry) N/A N/A N/A
"UHD Receiver" - logo (Industry) -
N/A N/A N/A
pending std
HDMI 2.0 4:4:4 @ 60p N/A N/A N/A
10-bit color support N/A N/A N/A
DAPQ N/A N/A N/A
Ambilight
Ambilight Version N/A N/A N/A
Pixels N/A N/A N/A
Ambilight Performance (nit, no of
N/A N/A N/A
colors, halo length)
Ambilight Features (Wall colour
adaptive, Lounge Light Mode, N/A N/A N/A
Ambilight Motion, Gaming Mode )
Ambilight for 3D N/A N/A N/A
Ambilight for all TV Events N/A N/A N/A
Ambilight Open Source via
N/A N/A N/A
JointSpaceApp
Wall Distance Adaptive (Stand vs N/A N/A N/A
Mount)
Motion Adaptive N/A N/A N/A
Built-in AL + Hue N/A N/A N/A
TV as Lamp(s) in Hue ecosystem N/A N/A N/A
In screen demo in mobile shop app N/A N/A N/A
Ambi Wakeup (ref HTV) N/A N/A N/A
Ambimusic N/A N/A N/A
Sound (TV)
Sound (Internal)
Output Power (10% THD) RMS 16W 16W 16W
Speaker configuration 8W+8W 8W+8W 8W+8W
Speaker system 2.0 2.0 2.0
Speaker type built-in(normal) built-in(normal) built-in(normal)
Auto Volume Levelier / Auto Volume
YES YES YES
Levelier +
Sound Claim (Incredible
Surround/Cinema Surround/Clear
N/A N/A N/A
Sound/AmbiwOOx/3D
Movie/Incredible Surround 3D)
Bass (Bass control/DBE/Ultra
N/A N/A N/A
Bass/Ultra Bass II )
Wireless Sound Interface N/A N/A N/A
Dolby Digital Decoder Type YES YES YES
DTS Studio Sound N/A N/A N/A
DTS 2.0+ Digital out N/A N/A N/A
Acoustic Compensation Filters 主板
N/A N/A N/A
滤波补偿
Dynamic Treble Enhancement 动态
N/A N/A N/A
高音增强
Programmable Bass And Treble Curve
N/A N/A N/A
（可编程的低音和高音曲线）用户
Visible Sound N/A N/A N/A
Sound (External)
External Sound device type N/A N/A N/A
Output Power (10% THD) RMS N/A N/A N/A
Design Specs
Stand type (Swivel/non Swivel) Metal Wing Metal Wing Metal Wing
RJ45*1/HDMI*3/VGA*1/AV- RJ45*1/HDMI*3/VGA*1/AV- RJ45*1/HDMI*3/VGA*1/AV-
I/O port to be clearly indicated （列 IN*1/VIDEO- IN*1/VIDEO- IN*1/VIDEO-
接口） OUT*1/Tuner*1/USB*2/CI*1/Ear OUT*1/Tuner*1/USB*2/CI*1/ OUT*1/Tuner*1/USB*2/CI*1/
phone*1/Coaxial-OUT*1 Earphone*1/Coaxial-OUT*1 Earphone*1/Coaxial-OUT*1
Local Keyboard 按键板 YES YES YES
Philips wordmark 商标logo PHILIPS PHILIPS PHILIPS

2
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Leading Edge 装饰件 7# Crystal 7# Crystal 7# Crystal
Vesa Wall Mount Compatible 壁挂孔 YES YES YES
Compatible Wall Mount 壁挂孔
200mm*300mm 200mm*300mm 200mm*300mm
规格
POS label
Connectivity (I/O)
HDMI Number *3(HDMI3 support MHL) *3(HDMI3 support MHL) *3(HDMI3 support MHL)
HDMI 1.4a HDMI(Side-out/Under-out) HDMI(Side-out/Under-out) HDMI(Side-out/Under-out)
HDMI 2.0 N/A N/A N/A
HDMI/DVI YES YES YES
HDMI ARC HDMI-2 HDMI-2 HDMI-2
EasyLink (HDMI-CEC) YES YES YES
Scart (EU) Connections N/A N/A N/A
YPbPr/CVI (EU/Latam) Connections N/A N/A N/A
CVBS (EU/Latam) Connections *1 *1 *1
Audio L/R in *1 *1 *1
CI+ slots *1 *1 *1
Antenna *1 *1 *1
Satellite (for K&S only) N/A N/A N/A
USB USB2.0/USB3.0 USB2.0/USB3.0 USB2.0/USB3.0
USB Harddisk Format (Power) FAT/NTFS (500mA) FAT/NTFS (500mA) FAT/NTFS (500mA)
VGA YES YES YES
VGA/DVI Audio Input share AV audio input share AV audio input share AV audio input
Digital audio out (SPDIF) N/A N/A N/A
Headphone *1 *1 *1
Ethernet-LAN RJ-45 *1 *1 *1
Service Connector VGA connectable VGA connectable VGA connectable
Wireless connections YES YES YES
Wi-Fi Band Concurrent N/A N/A N/A
WoWLAN N/A N/A N/A
WoLAN N/A N/A N/A
Bluetooth for subwoofer/RC (do not
N/A N/A N/A
claim commercially)
Multichannel over BT N/A N/A N/A
HDCP v2.2 (on HDMI 2.0 port) N/A N/A N/A
MHL (HDMI+power+return channel) YES YES YES
Wi-fi Miracast Certified (HDCP 2.2
N/A N/A N/A
supported)
GoogleCast Receiver N/A N/A N/A
Tablet Screen Mirroring (Wi-Fi N/A N/A N/A
Miracast)
TAD AppFTA channels (free app) N/A N/A N/A
TAD Server, FTA channel N/A N/A N/A
Indep. Watching (TV&PVR), FTA&CI+ N/A N/A N/A
SAT>IP Client, FTA N/A N/A N/A
HEVC @ FHD 60Hz N/A N/A N/A
HEVC @ UHD 60Hz N/A N/A N/A
H264 @ UHD N/A N/A N/A
VP9 @ UHD N/A N/A N/A
UI & Interaction
Ux (Basic: without Dashboard,
Basic Basic Basic
Advanced: with Dashboard)
Animations 动画 N/A N/A N/A
Drag and drop 拖动 N/A N/A N/A
Remote Control Version (state if
N/A N/A N/A
include Keyboard/Pointer)
Sensor.accelerometer & sensor
N/A N/A N/A
gyroscope
Easy access to eDFU (Blue key) 电
N/A N/A N/A
子说明书
Text Entry (Basic : Text Entry via HID
Basic Basic Basic
and/or On-screen Keyboard)
Multi-view 多屏显示 N/A N/A N/A
Multi-task 多任务 N/A N/A N/A
wide screen; 4:3; movie wide screen; 4:3; movie wide screen; 4:3; movie
Screen Format Adjustments 比例
expand16:9; subtitle zoom; expand16:9; subtitle expand16:9; subtitle
列表
unscaled zoom; unscaled zoom; unscaled
Dual Screen (TV and TeleText) 图 N/A N/A N/A
Teletext N/A N/A N/A

3
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
e-Sticker N/A N/A N/A
Priority Channel List N/A N/A N/A
Channel Cloning via USB N/A N/A N/A
Logo Editor (Channel Editor) N/A N/A N/A
Channel Matrix with EPG data N/A N/A N/A
Channel Scanning (Australia/NZ) N/A N/A N/A
Time Zone (Australia/NZ) N/A N/A N/A
PC Sorting N/A N/A N/A
Intelligent Source List N/A N/A N/A
On-screen Remote (via HDMI) N/A N/A N/A
Cold boot to broadcast N/A N/A N/A
Cold boot to online dashboard N/A N/A N/A
Warm boot to broadcast N/A N/A N/A
Warm boot to online dashboard N/A N/A N/A
Zapping OSD with EPG data N/A N/A N/A
Electronic Program Guide (IP &
N/A N/A N/A
Broadcast)
8 Days Electronic Program Guide YES YES YES
Live Setting Assistant (include PQ
N/A N/A N/A
level) 设置助手直播
Signal Strength Indication 信号
YES YES YES
强度指示
Pause TV/USB recording (PVR) 刻录 YES YES YES
Two simultaneous recordings in stdby N/A N/A N/A
English， Malaysia, Indonesian, English， Malaysia, English， Malaysia,
UI Languages
Thai, French, Portuguese,Chinese Indonesian, Thai, French, Indonesian, Thai, French,
Memory Profile (DRAM) 512M Portuguese,Chinese
512M Portuguese,Chinese
512M
Menu Layout Update 菜单更
N/A N/A N/A
新 换UI
Wizards (Ease of Installation) 安
N/A N/A N/A
装工具（类似螺丝刀）
Single Sign On (google a/c only) N/A N/A N/A
Personalized Dashboard（定制化 N/A N/A N/A
UI
Face recognition 面部识别 N/A N/A N/A
Shopmode 2015 N/A N/A N/A
CloudTV app content in search and
N/A N/A N/A
Dashboard (on TV)
Firmware Upgradeable 软件升级 YES YES YES
Multimedia Applications
MJPEG,MPEG-1,MPEG-2,MPEG- MJPEG,MPEG-1,MPEG- MJPEG,MPEG-1,MPEG-
Video Playback Formats
4,H.264,XviD,FLV,AVS. 2,MPEG-4,H.264,XviD,FLV,AVS. 2,MPEG-
Subtitles Formats Support SRT、ASS SRT、ASS 4,H.264,XviD,FLV,AVS.
SRT、ASS
Music Playback Formats MP2/MP3/AAC/M4A/PCM MP2/MP3/AAC/M4A/PCM MP2/MP3/AAC/M4A/PCM
Picture Playback Formats JPG/JPEG/PNG/BMP JPG/JPEG/PNG/BMP JPG/JPEG/PNG/BMP

4
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Smart TV
Software Platform
Android Home Page
Android OS
UI Resolution
Google Voice Search
Google Hangouts
Remote Control
Gesture
Pre-installed Google Apps (Google
Search, Google Hangouts, Google
Play Movies, Google Play Music,
Youtube)
Basic Performance Profile
Google Play
Memory size to install apps
Extendable USB storage for App Download
Smart TV Experience
DLNA 1.5 - DMR, DMP
DLNA 1.5 - DMS
MultiRoom Client, FTA+Scrambled
Non-Copy Protected & CI+
MultiRoom Server, FTA+Scrambled
Non-Copy Protected & CI+
PVR Auto Recording (IP-EPG)
API - access control
xTV Support
Rich User Interaction
Smart Home
4k photo support in Android apps
4k photo support in Picture apps
4k photo support in USB/DLNA
UHD content playback from all
sources (USB,DLNA,web)
NextFlix UHD
Youtube UHD
Google Play UHD
Smart TV with Broadcast PIP; single
video
SMART TV offline content (cached)
MPEG-DASH (CENC & CFF)
HLS
Wake up from APP
Preinstalled Apps
Netflix *
YouTube Leanback (HTML5) *
Spotify *
BBC iPlayer *
Skype
Skype Cowatch (mix audio)
Cloud Explorer
Cloud TV
Smart TV Services
Social Apps
Game Dashboard in Google launcher
OpenGL Games
Playstation Now App
OnLive App
STA 3.0 & 4.0 Clients
STA shared App store
Camera & Mic API
TV as an app (Verimatrix, etc)
Companion Apps
Philips TV Remote App
Sharing in Remote App
Ambilight TV App
Ambilight+Hue App
User Manual App
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Channel Editor - PC Client App
Mobile app for in-shop (cover
MRA/Demo Me/Shop RC functions)
Proximity based shop app activation
(BTLE/NFC/QR tbc)
MyRemote App (Old TV Remote App)
Ambilight Lounge App

Broadcast/Certification
DVB-T/C YES YES YES
DVB-S/S2 N/A N/A N/A
DVB-T/T2 YES YES YES
DVB-C2 N/A N/A N/A
SBTVD-T (Brazil) N/A N/A N/A
SATVD-T (Argentina) N/A N/A N/A
Analog (LATAM/APMEA) PAL SECAM NTSC PAL SECAM NTSC PAL SECAM NTSC
Nicam (APMEA) N/A N/A N/A
Enhanced SSU N/A N/A N/A
Italy HD Book 2.1.1 (GOLD) N/A N/A N/A
HD-Book Italy 3.0 (HEVC@FHD) N/A N/A N/A
UK D Book 7a N/A N/A N/A
Freeview SD (UK) N/A N/A N/A
Freeview HD (UK) N/A N/A N/A
MHEG 5(只有HbbTV有) N/A N/A N/A
TiVuON (IT) N/A N/A N/A
TNT HD (FR) N/A N/A N/A
Argentina Ginga - NCL N/A N/A N/A
Brazil Ginga (A/B ) N/A N/A N/A
Video Playback N/A N/A N/A
Dual Cam (CI+) N/A N/A N/A
Dual Tuner N/A N/A N/A
CI+ 1.4 Multistream CAM N/A N/A N/A
CI+ 1.3 CAM N/A N/A N/A
HBBTV 1.5 N/A N/A N/A
HBBTV 2.0 N/A N/A N/A
MHP N/A N/A N/A
Ziggo Interactief N/A N/A N/A
3D DVB Phase 1 N/A N/A N/A
3D signaling bits in broadcast N/A N/A N/A
Background update installation N/A N/A N/A
Marlin/ Play ready N/A N/A N/A
Sustainability/Power
PVC / BFR Free 无卤 N/A N/A N/A
Mercury Free 无汞 N/A N/A N/A
Cabinet Resin 面框材质 Metal Metal Metal
Eco-Flower Certified N/A N/A N/A
ECO Mode N/A N/A N/A
Mains Power AC 100-240V 50/60Hz AC 100-240V 50/60Hz AC 100-240V 50/60Hz
Standby Power <0.5W <0.5W <0.5W
Quick Startup NA NA NA
Network Standby mode (max 6W) NA NA NA
Off Mode Power <0.5W <0.5W <0.5W
Auto Switch-Off Timer 休眠时间 YES YES YES
Green packaging (Non-EPS) 绿
N/A N/A N/A
色包装
Light Sensor 光感应器 N/A N/A N/A
Picture Mute (For Radio) 单独听 N/A N/A N/A
EU Energy Label (A++/A+/A/B ) -
NA NA NA
Requirement
non-EU Energy Label - Standby Label
NA NA NA
(A/B/C)
Blauer Engel (Germany) NA NA NA
Accessory
By-packed accessories
Active Glasses (509) N/A N/A N/A
Active Glasses (529) N/A N/A N/A
Passive Glasses (PTA417 ) N/A N/A N/A

6
Product Specification Sheet
43" FHD STV(43S91F-DVB) 49" FHD STV(49S91F-DVB) 55" FHD STV(55S91F-DVB)
Dual Gaming Glasses N/A N/A N/A
Woofer (e.g. SWB50) with N/A N/A N/A
Soundbeam
Sound Bar N/A N/A N/A
Detachable speaker base 可拆卸喇 N/A N/A N/A
Wireless audio adaptor N/A N/A N/A
Wi-Fi Adapter N/A N/A N/A
(PTA01/00/PTA127/55
Skype Camera (PTA317)) N/A N/A N/A
Table Stand 底座 YES YES YES
Accessory Bag YES YES YES
Mains Cord (EU/UK/Brazil/APMEA )
YES YES YES
电源线
Remote Control + 2x Philips Batteries YES YES YES
Printed QSG YES YES YES
Printed DFU (APMEA) YES YES YES
Safety Legal Leaflet (EU) - 3D Health
Advise and Ukraine requirement（安 N/A N/A N/A
规小册子）
Philips Warranty Leaflet 保修卡 YES YES YES
Optional accessories
Active Glasses (PTA509/529) N/A N/A N/A
Passive Glasses (PTA419 ) N/A N/A N/A
Dual Gaming Glasses (PTA436) N/A N/A N/A
Wi-Fi Adapter N/A N/A N/A
(PTA01/00/PTA127/55
Skype Camera (PTA317)) N/A N/A N/A
Table Top Stand N/A N/A N/A
Speaker stand N/A N/A N/A
Others N/A N/A N/A
Certification
Dolby Digital/Dolby Digital Plus/Dolby
Pulse
DTS 2.0+ Digital out
DTS Premium Sound
DivX
WMA
Wi-Fi
DLNA Certified (DMR/DMP/DMS)
SKYPE
HDMI
MHL
Dimensions
(WxHxD)
Unit with stand 970*614*219mm 1102*696*258mm 1243*776*258mm
Unit without stand 970*564*74mm 1102*639*81mm 1243*720*81mm
Carton 1085*667*150mm 1210*744*175mm 1355*824*175mm
Wall-mount 200*300 mm 200*300 mm 200×300 mm
Weight
Product without Stand 8.3kg 9.5 kg 13.5kg
Product with Stand 8.5kg 10 kg 14kg
Product in Packaging 10.5kg 13.5 kg 17kg

7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
 Page 1 of 14 KTC

Troubleshooting Procedure

1. No power

Check 220V power supply voltage

and the contact of power socket
Check AC（ 220V ）voltage and the
contact of CN101 socket.

YES NO

Check +5V and +12V output from Replace power cord or power
embedded power supply for abnormity socket

YES NO

Check +5V and +12V on Abnormal output voltage +5V and +12V from
main board for abnormity embedded power supply, replace embedded
power supply with the same model
YES NO

Check for open-loop of fuse, Check main board of power supply for
or replace main board looseness, open-loop and poor contact

2. Without light

When the indicator is on but there is no display, check remote control for
power-off, minimum brightness, contrast ratio, check high-voltage switchboard
controlled by main board for abnormity

YES NO

Check the fuse on high-voltage board for Check each triode of control part for
the supply of 12V abnormity or replace main board

YES NO

Replace high-voltage switchboard Check fuse

26
3. Protection or without light (refers to the disappearance of image several seconds
after the emergence of image)

The image disappeared immediately after the

emergence; check the plug of high-voltage switch board
for striking sparks and poor contact

NO YES

No problems identified, replace high-voltage If there is spark striking,

board; if the fault remains, check the contact replace high-voltage board
line of back light of LCD for any damage, and
replace LCD board.

4. White panel

White panel refers to the back light works

without visible signal and just show white
screen. Check the voltage of socket for flat
cable connecting the main board to screen
for abnormality

YES NO

Check the interface between main board Check the power supply chip of
and connect line for any looseness, control screen or replace main
shedding, if no abnormity existed, board
replace LCD screen

27
 5. White screen after power
power--off (work normally when power on, but when power
power--off or
no signal input, the screen shows a white screen)

Check whether there is change of voltage at the high voltage

board controlled by main board when power-on and power-off

YES NO

Check whether the voltage change of the control pins on Check whether the voltage of the pin on main chip
the plug interface of high voltage board is normal when controlling the working voltage of high voltage board is
power-on and power-off normal when power-on and power-off

YES NO YES NO

The circuit Check whether the lines Check relevant circuits of Replace poor main
related to between main board and high high voltage board chips or recopy
high voltage voltage board is in open-loop controlled by main board software
board is poor or poor contact

6. TV without channel or with color cast

Check TV antenna plug for looseness and

poor contact

YES

If with color cast, check the setting of Replace antenna plug

color system under menu; and change
of color system to see whether it is
normal (Usually set to automatic)

NO

Check the antenna and its signal

source, if no problems exist, replace
tuner or control chips with the same
model

28
 7. Poor sound

Poor sound refers to without sound or with noise; check

whether the selection of sound system is proper

NO
YES

Switch to other audio input, check whether DVD No sound; check whether remote control mute is
input and PC main board input has sound selected and switch sound system

NO
YES
No sound for other inputs; check the sound
amplifier and the shared control circuit There is sound for other inputs,
replace TV tuner or control chip

8. No VGA input signal

VGA signal input does not respond, the screen

prompts “Please input signal”, check whether PC
signal source and signal line is normal.

YES NO

Check VGA signal input board and see whether the row Replace PC or signal line, check
and field sync signal protection diode is broke down display VGA plug for looseness

NO
YES
Replace the motherboard or
factory reset is normal Replace the 5.6V Zener diode
on the motherboard

29
 9. Poor embedded power supply of TV

Power on, check embedded power supply 5VSB in TV for 5V voltage output

YES NO

High electrical level existed at Check power supply line for looseness, check indictor for
STB (higher than 2.5V) working and power supply socket for looseness

YES NO YES NO

Check +5V ， +12V Check EC2 for 380-400V Fasten lines Replace power
for normal input voltage; if there is not, and socket supply
replace power supply
NO

Replace power supply

10. Common fault of LCD screen

10.1 Bright line or bright belt (BL): constant longitudinal or transverse illuminating line or
belt due to non-conformed connection between IC and glass
10.2 Dark line (DL): constant longitudinal or transverse illuminating line due to
non-conformed connection between IC and glass.
10.3 White panel (WP): only light tube illuminates owing to non-conformed drive plate of
the LCD, without any display signal in the display area, and the whole screen is white.
10.4 Screen breaking: (overflow of LCD): with damage or invisible damage of the liquid
crystal glass, irregular black defect occurs from liquid crystal body to glass and polarizer,
which can not be seen at any image. The overflow portion can not form image and does not
display.
10.5 Pressing Scrape (PS): after local display area at the front of LCD is heavily pressed,

30
glass of the pressed portion is not damaged, the liquid crystal body can not display normally,
with spot or block black defect.
10.6 Screen mess: irregular color display arising from damage of driving plate in LCD.

31
Level 1 menu Level 2 menu Level 3 menu data，remark

工厂复位初始化 EEPROM
factory reset 设定 factory reset,initialize
eeprom
ageing mode
Channels
Advanced
Setup
power-on Secondary/Memory/
mode Direct
Are you sure
Mboot Upgrade ?
update Mboot
upgrade 选项：confirm/Cancel

Are you sure

Upgrade ?
Main
选项：confirm 和 update main program
upgrade
Cancel

Input MAC
address
ADC adjustment
VGA(RGB),分量
Source
(SD,HD)choose
R-GAIN
The front-end gain
G-GAIN
adjustment
ADC ADJUST B-GAIN
R-OFFSET clamping electrical level
G-OFFSET adjustment
B-OFFSET
Phase Phase
Data debug Auto Tune
color temperature
adjustment
Color Temperature
 White level
R Gain
adjustment
White Balance
G Gain
B Gain
R Offset Black level adjustment
G Offset
B offset
Picture Mode Picture model adjust

32
 Brightness brightness
Constrast Constrast
Saturation Saturation
Hue Hue
Sharpness Sharpness
Backlight Backlight
Test Pattern

All kinds of curve

OSD_0
adjustment
OSD_25
Non_linear
OSD_50
OSD_75
OSD_100
 repetition rate
adjustment
Source Each signal source
OverScan H size WIDE adjustment
H position center position of Line
V size Field adjustment
V position center position of field
PEQ adjustment；
Fo：
Set to the center Frequency
point of Gain spectrum
Range 0~16000，step is
Fo1 coarse
100HZ
Fo1 fine Range 0~16000，step is 1HZ
Range 0~16000，step is
Fo2 coarse
PEQ 100HZ
Fo2 fine Range 0~16000，step is1HZ
Range 0~16000，step is
Fo3 coarse
100HZ
Fo3 fine Range 0~16000，step is 1HZ
Fo4 coarse
Fo4 fine
Fo5 coarse
Fo5 fine
Uart Enable （switch Uart）On/off
Debug tool can be used to
Uart Debug read memorizer via COM
port
EfficiencyBk

EfficiencyBk_Max

33
 AVC
CEC/ARC

Others
Panel model
PQ
Software
version
barcode

34
 Net Work TV MSD6A628 software upgrading (After service)

1, software upgrade tools and materials

* PC (WINDOWS XP system, USB2.0)
* AC100 ~ 240V power supply and power cord
* ISP programming board and cable
* ISP programming board driver
* USB flash drive (version 2.0, the capacity is not more than 2G)
* Upgrade software and boot files

2, preparation before upgrade.

Write down all signal ADC and white balance data in factory menu before upgrading (FLASH initialization may occur
after upgrade, color calibration data erased, and then revert to the written down data):

1. Under YPbPb signal source, press the MENU key to pop up the main menu, and then press 8202 by number keys to
enter the factory menu, select ADC ADJUST item, press the OK button to enter the next menu, move the cursor to the
MODE key, press the left / right cursor keys to select YPbPr (SD) items, recorded R-GAIN / G-GAIN / B-GAIN value
and R-OFFSET / G-OFFSET / B-OFFSET value.
2. Undert ADC ADJUST item and press OK to enter the next menu move the cursor to the MODE key, press the left /
right keys to move the cursor to select YPbPr (HD) items, recorded R-GAIN / G-GAIN / B- GAIN value and R-OFFSET
/ G-OFFSET / B-OFFSET value.

3. Under VGA signal source, press MENU in the main menu pops up, then press 8202 by number keys to enter the
factory menu, select ADC ADJUST item and press OK to enter the next menu, move the cursor to the MODE key, press
the left / right cursor keys to select YPbPr (SD) items, recorded R-GAIN / G-GAIN / B-GAIN value and R-OFFSET /
G-OFFSET / B-OFFSET value.

35
 Wite donw YPbPr(SD)and
YPbPr(HD)value before upgrade
and wite down VGA mode
R/G/B-GAIN and R/B/G-OFFSET
value ， change back to original
value after software upgrade
finished .

1. In Android system main interface, move cursor to “network”--“Ethernet”item, click mouse left button to get into ,
record MAC address.

MAC address

3, the software upgrade content and procedures :

1. U disk formatted as FAT32 format , and then upgrade the software ( software name and case is MstarUpgrade, suffix
bin) put in the U disk .
There are two ways for software upgrade, recommended mode 1.

The bigger the file, the longer time

upgrade will take, it is normally about
3~4 minutes，give enough time to
make sure upgrade success

Method 1: In the case of TV normally boot, enter the factory menu upgrade: power on machine, insert disk into the TV
USB interface, and then enter the factory menu, move the cursor to the Other Option Press OK to enter , and then move
the cursor to Upgrade Main options , press OK to upgrade.

36
 TV display tip

Press OK button to
upgrade

Method 2: Insert U disk into TV main board or programming fixture board USB interface , long press VOL + key, then
power on TV ( main board ) , after about five seconds the TV ( remote control panel ) indicator fast when flashing ,
indicating that the TV is being upgraded , after the light is not blinking on and off ( this process is time-consuming
depending on the size of the main board software , the greater the file the longer the software upgrade , the upgrade takes
roughly three minutes when the board software has 270M , 500M needs four minutes ) , means upgrade is complete .

3. Notes:
a. the file name and the case cannot be wrong , otherwise it will not be upgraded .
b. When using the U disk upgrade, sometimes light will no longer flashing after a TV remote control panel lights
flickering flashes ten seconds, this is upgrade failure. Normal upgrade remote panel lights flashing to be more than two
minutes, in this case upgrade again by powering off main board.
c. after powering off, if main board cannot upgrade normally , programming again the boot file (Mboot.bin or
MbootUprade.bin).
e. If the operator of this program is not familiar with the software, under the condition the can see factory menu
recommended upgrading the operating menu to enter the factory to prevent misuse.

4, when the above third step cannot be upgraded, upgrade the boot file first; please refer to the following specific
operating instructions.
MSD6A628 Network TV main board related upgrade packages with mboot.bin and MbootUpgrade.bin equipped with
two boot files. Both boot files function are the same, but there are differences between upgrade methods, only one
upgrade one of them. If the current TV main board can work properly, copy the boot files to the U disk after formatted
FAT32, then follow the instructions below to upgrade:

Method 1 : first MbootUpgrade.bin boot files, stored in the U disk, and then insert U disk in TV main board USB port,
press and hold the VOL + button on the TV control panel and hold, then power on TV ( main board), approximately after
five seconds the TV ( remote control panel ) indicator flashes rapidly , indicating that the TV is being upgraded , after the
light is not blinking on and off (time-consuming of this process approximately 60 seconds ) , indicating that the upgrade
is complete .

Method 2 : first Mboot.bin boot files stored in the U disk, then U disk inserted in the TV main board USB interface to
power on TV, and then press the MENU button on the remote control and then followed by 8202 the number keys to enter
the factory menu, move cursor to Other Option press OK to enter , and then move the cursor to upgrade mboot option ,
press OK to upgrade ( this time-consuming of this process is about 15 seconds ) .

Notes:
1.mboot.bin and MbootUpgrade.bin files can be put together in a U- disk, but no matter what methods to upgrade, all
operating according to operation instructions, control time to upgrade, ensure that the upgrade completed before power
failure, otherwise upgrade fails.
2. Because the boot files related to the TV's screen resolution and other relevant parameters, so before the software

37
upgrade boot files of each board must be upgrade first.
3. If the above two methods cannot upgrade, using programming board online upgrade following the instructions:
5, Programming board driver installation.
Use programming board online upgrade, programming board driver program has to be installed to PC, see the following
operation instructions.
1.use USB connecting wire to connect programming board and personal PC.

ISP programming
board
To personal
PC

2. PC identify new device, choose to install from list or specified location and appoint driver file position as figure.

38
3. after PC finds driver file, below information will be prompted during installation, click on , remains can be installed, the
system will install the driver process three times , namely : Mstar USB Debug Tool A; Mstar USB Debug Tool B; Mstar
USB SerialPort , install the three drives in order !

6. use programming board online upgrade boot file.

1. Use a USB cable and VGA cable to connect the programming board and TV main board , computer main bard and
then powering on main board.

39
 To personal PC
USB interface

To TV main
board VGA
socket

2. Double-click to run MStar ISP Utility v4.6.t2.exe, click the "Auto" icon on the main toolbar under the type selected for
eMMC.

3. Click the "Read" button in the main toolbar under load in EISP Loader File1 munim_EISP_boot _ ** _ **. Bin, in EISP
Read File1 load rom_emmc_boot.bin, in EISP Loader File2 load munim_EISP_user _ ** _ **. Bin, load mboot.bin
( Figure 2 ) in EISP Read File2.

40
4. Click on the main toolbar "Config" button , the interface is set up according to the pictures of their respective settings.

5. Click on the main toolbar "Connet" button at the top of the tab bar to run the program will display [ Device Type
eMMC ] .

41
 Click “Connet” button under tool bar, running
program top part will show【Device Type eMMC】

After click“Stop/Run”button，
if interface lower right corner
shows “Connecting.....” and tab
bar shows as “【Device Type
eMMC】 “ means connecting is
failed or current main board can
only us U disk to upgrade.

If there is no showing of [ Device Type eMMC ] upgrade cannot be conducted , please check the programming board is
properly connected and if main board can boot (main board can boot normally not display [ Device Type eMMC ,] need to
upgrade the software, copying it into U disk, press and hold the button panel VOL + button first and powering on main
board, wait for LED indicator on the machine flashes for about five seconds and then unplug the U disk and re- power
main board to display ) .

7. Check "Auto" icon in the menu settings are consistent with the figure below, and then click "Run" button to boot file to
program.

42
 Programming
Execute button progress

result

Programming progress bar will scroll now, after programming is finished, it will show “Pass”。

7, Main board driver upgrade.

1. U disk formatted as FAT32 format, and then upgrade the software ( software name is MstarUpgrade, suffix is bin) put in
U disk .
2. Insert U disk into main board or programming TV fixture USB port , press VOL + key, then power on TV ( main board)
after about five seconds the TV ( remote control panel ) indicator flashes rapidly , indicating the TV is being upgraded ,
when the light stops blinking and goes out ( this process time-consuming is depending on the size of the main board
software , the greater the file the longer the software upgrade time , when the board is 270M, upgrade software takes
roughly three minutes ,when 500M , it is about four minutes ) , indicating that the upgrade is complete .

3. Notes：
a. the file name and case cannot be wrong , otherwise it will not be upgraded .
b. When using U disk to upgrade, sometimes after light does not flat after a TV remote control panel lights flickering
flashes ten seconds, this is upgrade failure. Normal upgrade remote panel lights flashing more than two minutes , place the
board in case of power failure in this case re- board software upgrade.
c.main board cannot be upgraded after powering on , please programming boot file again (Mboot.bin or
MbootUprade.bin).

8, after the upgrade is complete, install machine cover, before delivery, factory adjustment must be carried out :
1. powering on machine, press the MENU button on the remote control to the main menu pops up, then press 8202
followed by the number key to enter the factory menu , press the up / down keys to move the cursor to the "Other Options"
option Press the Up / Down keys move the cursor to the "Restore To Default" option by right the reset command , a black
screen for about 8 seconds and the machine automatically re- power on reset operation is completed .

43
2. Completed initialization within three minutes after inserting VGA signal wire and powering on machine (automatically
initializes started after factory menu reset is ) switch to VGA signal source . Press the MENU key to pop up the main menu, and
then followed by 8202 the number keys to enter the factory menu, press the Shift key to "ADC ADJUST" and press the OK
button to enter the next menu, press the left / right keys to move the cursor to select VGA item, then press shift keys to move the
cursor to the AUTO TUNE key and press the OK button to execute the self-adjusting command. There is a corresponding entry in
the AUTO TUNE Tip: SUCCESS, means self-adjusting qualified, FAILS, means self-tuning failure, need to self adjusting again.

3. under YPbPb source ,input 480i 100% color bar signal to machine . after press NEMU poping-up main menu , then
followed by 8202 the number keys to enter the factory menu , select ADC ADJUST item , press the OK button to enter the
next menu , press the left / right keys to move the cursor to select YPbPr (SD) item , press down keys to move the cursor to
the AUTO TUNE key and press the OK button to execute the self-adjusting color commands. There is a corresponding
entry in the AUTO TUNE Tip : SUCCESS , means self-adjusting qualified , FAIL , means self-adjusting is filed, needed to
adjust again.

44
 Press right and left key to execute self
adjusting order , SUCCESS is OK ，FAIL
is failure ( need to re adjusting)

4. Under YPbPb signal source , input 720P 100% color bar signal to machine. Afater pressing NEMU pop-up main menu,
then followed by 8202 the number keys to enter the factory menu , select ADC ADJUST item , press the OK button to
enter the next menu , press the left / right keys to move the cursor to select YPbPr (HD) key, then press down keys to move
the cursor to the AUTO TUNE key and press the OK button to execute the self-adjusting color commands. There is a
corresponding entry in the AUTO TUNE Tip : SUCCESS , means self-adjusting qualified , FAIL , means self adjusting is
failed, need to adjust again.

Press right and left key to execute self

adjusting order , SUCCESS is OK ，FAIL
is failure ( need to re adjusting)

5. about white balance adjustment:

* need to input standard graphics to TV during auto white balance self adjusting, recommended instrument is
CHROMA222293.
* In case not plugging signal line, in the factory menu of ADC Adjust, change the source value of VGA, YPBPR (HD),
R-GAIN YPBPR (SD) for each mode / G-GAIN / B -GAIN value and R-OFFSET / G-OFFSET / B-OFFSET to the
original value before upgrade.
9 , MAC address programming refers to "MSD6A628 Msd6a608 MSD6A818 smart network TV MAC address code
programming Guide" , in general, just use U disk to upgrade ( do not use programming board burn boot files MAC in
machine, will not erased , if using programming board to re- burn the boot files , MAC address programming is
needed ) .
10, after ADC ADJUST debugging finished, press the MENU button several times to exit the factory menu to save the
data , turn the machine off and then restore the original packaging.

45
 5 4 3 2 1

3.3V_NORMAL 12V_NORMAL
AS1117
RESET
TUNER PWR TUNER_3.3V 屏电压 40P LVDS SPK-L
Audio AMP
AS1117 TPA3110LD2
D 12V_NORMAL D
SPK-R
1.28V VDDC_CPU PWR MOS管控制
12V_NORMAL DC-DC

1.15V VDDC PWR

DC-DC
5V_NORMAL DVB-T2 DEMOD
IF
DDR PWR DDR PWR 1.5V MSB102KT

5V_STANDBY
DC-DC MSD6A628VXEM
3.3V_Standby
3.3V_STANDBY (DVB-T/C/T2) SILICON TUNER
AS1117 TDA18275HN
PWR_ON/OFF
TUNER_3.3V

RF
32Gbit

AV-OUT
COAXIAL
IR&KEY

USB
GPIO

PCMCIA

AV-IN
三极管控制 EMMC FLASH

VGA
IR&KEY TUNER CONN
HDMI1
C C
HDMI1 HDMI2
(ARC) LAN

HDMI2 LAN PCMCIA AV-IN VGA COAXIAL VEDIO-OUT USB

HDMI3
(MHL)

B B

A A
KTC ISO9001.ISO14001体系文件

文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。 文件编号： T4270 版本：3.0 页数: 2 of
9
This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
Do not spread to third party without the written permission. 设计: 张志清 审核: 批准:
版权所有@深圳市康冠技术有限公司
Copyright@ ShenZhen KTC Technology Co., LTD
发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

+5V_Normal
Connetor C146
470uF/16V
+5V_Standby
+5V_Standby
VDDC DC/DC
CN101 12pin/2.0MM
C140 0.1uF R46
PM5V 1 +12V_Normal
PM5V 2 C141 U10
R29 10R
开机初始电压保证到IC pin 为1.15V！
5VSB 3 +5V_Standby
2K C137 2 IN BST 5 VDDC_1.15V VDDC VDDC_VSENSE
L1
4 STANDBY R14 100R PWR-ON/OFF 0.1uF 10uF C66
standby H:ON PWR-ON/OFF 4 R62 100K U6_EN 6
5 EN/SYNC 0.1uF
GND L:OFF 3 2 1
6 SW SPM65301R5/5A
GND +5V_Normal 7 R55 0R/NC
VCC

GND
BL_ON/OFF 7 R56 0R VDDC_VSENSE
1 AAM FB 8
C59 C17 C20
8 C70 C10 R7 R8
BL_PWM C143 C144
MP2225 6.2K_1% 240R_1% C35 C52 C54 C58

4
D D
10uF 10uF
12V 9 +12V_NORMAL 0.1uF 0.1uF
12V 10 10uF/16V 0.1uF
R1
10uF/16V
0.1uF
11 C138 470uF/16V R74
GND 22uF 22uF22uF
GND 12 0R R48
C139 0.1uF R2
+5V_Normal 6.8K_1% 靠近DC-DC

反馈电阻靠近DCDC,敏感线,远离干扰源
R6
Inverter controler Vout=0.6V*(1+R1/R2)
1K !!! 至少需使用5A DC/DC
BL-ADJUST 1K R51
3

Q1
C53 R49 1 U14
BRI_ADJ 4,6 VDDC_CPU VDDC_CPU_VSENSE
4.7K R50 L13
1 2.2uF/DC 3904 +12V_NORMAL VDDC_CPU_1.15V
2

BL_ADJUST NC/10K SAMSUNG panel 0~3.3V R34=10K 8 PVDD LX 6 2 1

2 LG/CMO/AU panel 0~5V,R34 NC
BL_ON/OFF 3R3/2A
+5V_Normal R121 R115
GND 3 1 EN BST 7 C121 0.1uF
100K C126
CN102 NC/0R
3Pin/2.0MM R52 3 2 FB2 18nF
R43 C128 C122 5V FB R113 0R VDDC_CPU_VSENSE

PowerPAD
4.7K C130 C131 C133 C129 C104 C145
10K 4 5 R102
BL-ON/OFF SDA SCL 6.2K_1%
3

Q10 10uF 10uF

0.1uF
1 R57 4.7K 0.1uF 1uF R122 R124
R1 22uF 22uF
22uF
3

Q11 靠近DC-DC

9
3904 1 R54 4.7K 100R 100R R104
VBL_CTRL 4 MSH6000A
2

47K_1%
3904 "VBL_CTRL" IO口为高电平时，背光开。 4,9 M_SDA M_SCL 4,9 R2
Addr 0xC0 靠近DC-DC
2

R53 10K "VBL_CTRL" IO口为低电平时，背光关。

C C

Vout=1.1V*(1+R1/R2) 开机初始电压保证到IC pin 为1.24V！

电阻靠近DCDC,敏感线,远离干扰源
!!! 至少需使用2A的 DC/DC
Power for panel Panel_VCC

Q12
VCC_P ME2325
+12V_NORMAL
L111
0805_BEAD/12V屏 C37 R41 C67
10K
0.1uF 1uF CA8
至少需使用500mA DC/DC!!
PANEL_ON

R58
C47

0.1uF
+

100uF/16V
+5V_Standby
L112 0805_BEAD
U12
SY8088
L12
1A Max
+1.5V_DDR LDO
100K 4 VIN SW 3 2 1
SWPA3015S2R2NT/1.5A

4
U11 U13 U16
C110 33pF
3

Q9 R103 3K AMS1117L-3.3 AMS1117L-3.3 AMS1117L-3.3

1 5 R1

ADJ

OUT

ADJ

OUT

ADJ

OUT
PANEL_ON/OFF R42 4.7K1 EN FB

IN

IN

IN
500mA
GND
4 PANEL_ON/OFF C117 C118
C114 C106 C105 400mA Max
R40 3904 310mA Max
2

3
10K 0.1uF +3.3V_TU V_TU
22uF
2

10uF +3.3V_Standby +3.3V_Normal

10uF 0.1uF
靠近DC-DC R111 2K 靠近DC-DC
+5V_Standby
C115
+5V_Normal
C116
R2 C109 C135 C101 C102 C123 C107 C108 C112 C48 C15 C49 C50
+5V_Normal C78
2.2uF 0.1uF 0.1uF 2.2uF 2.2uF 0.1uF 0.1uF 2.2uF 0.1uF 0.1uF 2.2uF 22uF
2.2uF
10uF 10uF
+12V_Normal

B
Vout=0.6V*(1+R1/R2) TUNER POWER B
+3.3V_Standby
R3

R15

R168 10R R157 IR-in R167 100R IRIN

IRIN 4
200R

200R

C148
R9 10K +5V_Standby
10K 30pF
+5V_Standby 0.1uF
3

Q208 R182
IR_5V

3904 1R13 10K C181

2K
2

Q207
3

3904 1R12 10K STANDBY 1 R126 4.7K

+5V_IN LED
1
2 IR-in Q112 LED 4
2

12V放电电路 IR_IN 3904

2

GND 3
R159 4.7K 所用IO口 SAR0 SAR1
4 LED+ R155 4.7K +3.3V_Standby
LED
H12 H11 H21 H22 5 KEY0-in R171 1K 按键功能 CH+ CH- SOURCE POWER V0L- V0L+ MENU
KEY0 KEY_SAR0 4
1

5 9 5 9 5 9 5 9 KEY1-in R142 1K
KEY1 6 电阻值 0欧 2K 6.8K 1K 0欧 2K 6.8K
KEY_SAR1 4
4 8 4 8 4 8 4 8 KEY_POWER R194 1K
PWR 7
C179 C150 电压值 0V 0.98V 1.95V 0.58V 0V 0.98V 1.95V
3 7 3 7 3 7 3 7 ED1 ED2 0.1uF
GND 8
2 6 2 6 2 6 2 6
C174 0.1uF 1pF 1pF 0.1uF IR&KEY Connector
8pin/2.0MM
NC NC NC NC CN103

A A
1

H26 H24 H23 H20 H29 H17 H19 H28 H27 H30
NC NC NC NC NC NC NC NC NC NC

Test Point & MARK

1

SN2 SN
NC NC
KTC ISO9001.ISO14001体系文件
本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。 文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
Do not spread to third party without the written permission. 文件编号： T4270 版本：3.0 页数: 3 of 9
版权所有@深圳市康冠技术有限公司 设计: 张志清 审核: 批准:
Copyright@ ShenZhen KTC Technology Co., LTD 发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

HDMI GPIO Pull Up/Down PCMCIA & TS PCM_A[14:0]

PCM_A[14:0] 9
HDMI Interface U201D +3.3V_Normal
U201C
PCM_D[7:0]
PCM_D[7:0] 9
U201A
M_SCL R189 4.7K TS_MDO0 TS_MDO0 Y12 Y17 PCM_A0
HDMI1-RX0N G2 B9 USB0_D- 3,9 M_SCL TS Input TS0_D[0] PCM_A[0]
8 HDMI1-RX0N RX0N DM_P0 USB0_D- 7 M_SDA R191 4.7K TS_MDO1 TS_MDO1 Y11 Y15 PCM_A1
HDMI1-RX0P H3 A8 USB0_D+ 3,9 M_SDA TS0_D[1] PCM_A[1]
8 HDMI1-RX0P RX0P DP_P0 USB0_D+ 7 3D_EN R195 4.7K TS_MDO2 TS_MDO2 AB12 AB16 PCM_A2
HDMI1-RX1N H2 C9 USB1_D- GPIO_PM0 H6 3D_EN TS0_D[2] PCM_A[2]
8 HDMI1-RX1N RX1N DM_P1 USB1_D- 7 GPIO_PM[0] / (TCON[8]) TS_MDO3 TS_MDO3 AA12 Y16 PCM_A3
HDMI1-RX1P J3 A9 USB1_D+ B4 TS_MDO[7:0] TS_MDO4 TS0_D[3] PCM_A[3]
8 HDMI1-RX1P RX1P DP_P1 USB1_D+ 7 PM_UART_TX Demod_RST R196 4.7K TS_MDO4 AB13 AB15 PCM_A4
HDMI1-RX2N J2 B10 MHL_CABLE_DET J4 9 TS_MDO[7:0] TS0_D[4] PCM_A[4]
8 HDMI1-RX2N RX2N DM_P2 8 MHL_CABLE_DET GPIO_PM[2] / (MHL_CDS) TS_MDO5 TS_MDO5 Y13 AA15 PCM_A5
HDMI1-RX2P J1 A10 M6 TS0_D[5] PCM_A[5]
8 HDMI1-RX2P RX2P DP_P2 GPIO_PM[3] / (MHL_VBUS_EN) TS_MDO6 TS_MDO6 Y14 AA16 PCM_A6
HDMI1-CLKN G3 F6 TS0_D[6] PCM_A[6]
8 HDMI1-CLKN RXCN 3 PWR-ON/OFF PWR-ON/OFF TS_MDO7 TS_MDO7 AA13 AA14 PCM_A7
HDMI1-CLKP G1 C4 TS0_D[7] PCM_A[7]
8 HDMI1-CLKP RXCP PM_UART_RX TS_MOCLK TS_MOCLK AA11 Y9 PCM_A8
HDMI1-SCL K5 A2 9 TS_MOCLK TS0_CLK PCM_A[8]
8 HDMI1-SCL DDCDA_CK GPIO_PM[6] / (SPI_CS) TS_MOSTART TS_MOSTART AE11 Y4 PCM_A9
HDMI1-SDA K4 AC5 USB3_SSRXN C6 9 TS_MOSTART TS0_SYNC PCM_A[9]
8 HDMI1-SDA DDCDA_DA SSRXN USB3_SSRXN 7 GPIO_PM[7] / (SD_CDZ) TS_MOVAL TS_MOVAL AC11 W5 PCM_A10
HDMI1-HPDIN K6 AD5 USB3_SSRXP AMP-MUTE H5 P24 9 TS_MOVAL TS0_VLD PCM_A[10]
8 HDMI1-HPDIN HOTPLUGA SSRXP USB3_SSRXP 7 7 AMP-MUTE GPIO_PM[8] / (TCON[10]/WOL) LVSYNC W6 PCM_A11
HDMI1-ARC C1 AE4 USB3_D- 3D_SYNC_IN J6 P23 PCM_A[11]
8 HDMI1-ARC ARC0 DM USB3_D- 7 GPIO_PM[10] / (TCON[9]) LHSYNC TS_D0 TS_D0 AD11 AD10 PCM_A12
AD4 USB3_D+ R24 TS1_D[0] PCM_A[12]
DP USB3_D+ 7 LDE Input/output TS_D1 TS_D1 AD12 AB9 PCM_A13
HDMI2-RX0N D2 AE3 USB3_SSTXN 3 LED LED_R G6 R23 TS1_D[1] PCM_A[13]
8 HDMI2-RX0N D_RX0N SSTXN USB3_SSTXN 7 PM_LED LCK TS_D2 TS_D2 AC12 AA9 PCM_A14
HDMI2-RX0P E3 AD3 USB3_SSTXP TS1_D[2] PCM_A[14]
8 HDMI2-RX0P D_RX0P SSTXP USB3_SSTXP 7 3D Sync Modulation in TS_D3 TS_D3 AE13
HDMI2-RX1N E2 TS_D[0:7] TS1_D[3]
8 HDMI2-RX1N D_RX1N TS_D4 TS_D4 AC13 W7 PCM_D0
D HDMI2-RX1P F3 B5 T24 B0M 9 TS_D[0:7] TS1_D[4] PCM_D[0] D
8 HDMI2-RX1P D_RX1P LAN_LED[0] PAD_R_ODD[7]/LVB0- B0M 6 TS_D5 TS_D5 AD13 AB4 PCM_D1
HDMI2-RX2N F2 C5 T25 B0P TS1_D[5] PCM_D[1]
8 HDMI2-RX2N D_RX2N LAN_LED[1] PAD_R_ODD[6]/LVB0+ B0P 6 TS_D6 TS_D6 AE14 T5 PCM_D2
HDMI2-RX2P F1 B7 MDI_RN TP47 1 UART-TX1 AB19 T23 B1M TS1_D[6] PCM_D[2]
8 HDMI2-RX2P D_RX2P RN MDI_RN 8 GPIO3/(TX1) PAD_R_ODD[5]/LVB1- B1M 6 TS_D7 TS_D7 AC14 T6 PCM_D3
HDMI2-CLKN D3 C7 MDI_RP UART-RX1 AB18 U25 B1P TS1_D[7] PCM_D[3]
8 HDMI2-CLKN D_RXCN RP MDI_RP 8 GPIO4 / (RX1) PAD_R_ODD[4]/LVB1+ B1P 6 TS_CLK TS_CLK AD14 U6 PCM_D4
HDMI2-CLKP D1 B6 MDI_TN U23 B2M 9 TS_CLK TS1_CLK PCM_D[4]
8 HDMI2-CLKP D_RXCP TN MDI_TN 8 PAD_R_ODD[3]/Vx1_0-/LVB2- B2M 6 TS_SYNC TS_SYNC AC15 V5 PCM_D5
HDMI2-SCL D6 A6 MDI_TP V24 B2P 9 TS_SYNC TS1_SYNC PCM_D[5]
8 HDMI2-SCL DDCDD_CK TP MDI_TP 8 PAD_R_ODD[2]/Vx1_0+/LVB2+ B2P 6 TS_VLD TS_VLD AD15 V6 PCM_D6
HDMI2-SDA D5 F5 W24 BCKM 9 TS_VLD TS1_VLD PCM_D[6]
8 HDMI2-SDA DDCDD_DA VID0 PAD_R_ODD[1]/Vx1_1-/LVBCLK- BCKM 6 U5 PCM_D7
HDMI2-HPDIN D4 E6 W25 BCKP PCM_D[7]
8 HDMI2-HPDIN HOTPLUGD VID1 PAD_R_ODD[0]/Vx1_1+/LVBCLK+ BCKP 6
Y25 B3M
PAD_G_ODD[7]/Vx1_2-/LVB3- B3M 6 EMMC_CLK AC20 AA5 PCM_CD_N
HDMI3-RX0N AD7 AA2 C237 0.1uF DIF2 6 Y24 B3P 6 EMMC_CLK EMMC_CLK / (NAND_DQS) PCM_CD_N PCM_CD_N 9
8 HDMI3-RX0N C_RX0N VIFM PAD_G_ODD[6]/Vx1_2+/LVB3+ B3P 6 EMMC_CMD AE19 Y7 PCM_CE_N
HDMI3-RX0P AC8 AA3 C238 0.1uF DIF1 6 3 KEY_SAR0 KEY0-in E5 AA24 B4M 6 EMMC_CMD EMMC_CMD PCM_CE_N PCM_CE_N 9
8 HDMI3-RX0P C_RX0P VIFP SAR0 PAD_G_ODD[5]/Vx1_3-/LVB4- B4M 6 EMMC_RSTZ AD19 Y6 PCM_IORD_N
HDMI3-RX1N AD8 AB2 IF_AGC KEY1-in F4 AA23 B4P 6 EMMC_RSTZ EMMC_RSTN PCM_IORD_N PCM_IORD_N 9
8 HDMI3-RX1N C_RX1N IFAGC 3 KEY_SAR1 SAR1 PAD_G_ODD[4]/Vx1_3+/LVB4+ B4P 6 AA8 PCM_IOWR_N
HDMI3-RX1P AC9 9 Demod_RST G4 PCM_IOWR_N PCM_IOWR_N 9
8 HDMI3-RX1P C_RX1P SAR2 AE10 PCM_IRQA_N
HDMI3-RX2N AD9 VBL_CTRL J5 PCM_IRQA_N PCM_IRQA_N 9
8 HDMI3-RX2N C_RX2N 3 VBL_CTRL VBL_CTRL NAND_ALE EMMC_D1 AD17 Y5 PCM_OE_N
HDMI3-RX2P AE9 Power_Detect C8 AB25 A0M 6 NAND_ALE NAND_ALE/SPI_CK-NONPM PCM_OE_N PCM_OE_N 9
8 HDMI3-RX2P C_RX2P Power_Detect PAD_G_ODD[3]/LVA0- A0M 6 NAND_CEZ EMMC_D6 AD18 Y8 PCM_REG_N
HDMI3-CLKN AC7 C3 AB23 A0P 6 NAND_CEZ NAND_CEZ PCM_REG_N PCM_REG_N 9
8 HDMI3-CLKN C_RXCN SAR4 PAD_G_ODD[2]/LVA0+ A0P 6 NAND_CE1Z EMMC_D7 AC18 AA7 PCM_RESET
HDMI3-CLKP AE7 Y1 AC25 A1M 6 NAND_CE1Z NAND_CEZ1 PCM_RESET PCM_RESET 9
8 HDMI3-CLKP
8 HDMI3-SCL
HDMI3-SCL AA6
C_RXCP
DDCDC_CK
TGPIO0
TGPIO1 Y2 TUNER I2C PWM_PM G5 PWM_PM
PAD_G_ODD[1]/LVA1-
PAD_G_ODD[0]/LVA1+ AC24 A1P A1M
A1P
6
6
6 NAND_CLE
NAND_CLE
NAND_RBZ
EMMC_D5 AD16
EMMC_D0 AC17 NAND_CLE PCM_WAIT_N AB7
AB8
PCM_WAIT_N
PCM_WE_N PCM_WAIT_N 9
HDMI3-SDA AB6 AB3 T_SCL T_SCL AA17 AD25 A2M 6 NAND_RBZ NAND_RBZ/SPI_DO-NONPM PCM_WE_N PCM_WE_N 9
8 HDMI3-SDA DDCDC_DA TGPIO2 / (SCKM1) T_SCL 6 PWM0 / (SDIO_D[3]) PAD_B_ODD[7]/LVA2- A2M 6 NAND_REZ EMMC_D4 AE16
HDMI3-HPDIN AE6 AD2 T_SDA T_SDA BRI_ADJ AA19 AD24 A2P 6 NAND_REZ NAND_REZ/SPI_DI-NONPM
8 HDMI3-HPDIN HOTPLUGC TGPIO3 / (SDAM1) T_SDA 6 3,6 BRI_ADJ BRI_ADJ PAD_B_ODD[6]/LVA2+ A2P 6 NAND_WEZ EMMC_D3 AC16
AVDD5V_MHL AVDD5V_MHL AB5 PANEL_ON/OFF AC21 AE24 ACKM 6 NAND_WEZ NAND_WEZ
AVDD5V_HDMI_C 3 PANEL_ON/OFF PANEL_ON/OFF PAD_B_ODD[5]/LVACLK- ACKM 6 NAND_WPZ EMMC_D2 AC19
3D_Glasses_PWM Y19 AC23 ACKP 6 NAND_WPZ NAND_WPZ
HDMI-CEC PWM3 PAD_B_ODD[4]/LVACLK+ A3M ACKP 6 AA18
8 HDMI-CEC L5 AE23 PCM2_RESET/SD_CLK
CEC 3D Sync Modulation OUT PAD_B_ODD[3]/LOCKn/LVA3- A3P A3M 6 Y18
AD23 PCM2_WAIT_N/SD_CMD
PAD_B_ODD[2]/HTPDn/LVA3+ A4M A3P 6
4 HDMI1-ARC_DET B2 PM_SPI_CK PAD_B_ODD[1]/LVA4- AE22 A4M 6
+3.3V_TU +3.3V_TU SPI_SDI A3 AD22 A4P
PM_SPI_DI / (HW STRAPPING) PAD_B_ODD[0]/LVA4+ A4P 6
B3 PM_SPI_DO
MSD6A628 F12 PM_SPI_CZ / (NC) MSD6A628
R206
R161 R164 UART-RX B1
4.7K 4.7K 10K UART-TX DDCA_CK
C2 DDCA_DA
IF_AGC R205 0R IF_AGC_T 6
3,9 M_SCL I2C-SCL AA20 W22
T_SCL I2C-SDA DDCR_CK TCON[7]
T_SCL 6 3,9 M_SDA Y20 DDCR_DA TCON[6] Y22
T_SDA T_SDA 6 C216 AA22
SYSTEM I2C SYSTEM-RST TCON[5]
22nF B8 AB22
RESET TCON[4]
TCON[3]/PWM2 W21
改用47NF 3 IRIN IRIN A5 AB21
IRIN TCON[2]/3D_FLAG
TCON[1] AA21
TCON[0] Y21

J109
1
2
3D_L/R_FLAG
3D_SYNC_IN
3D interface
3D glasses launch
+5V_NORMAL

R106
7 USB3_EN
7 WIFI_EN
USB3_EN

3D_EN
AD21
AC22
PWM5
PWM4
MIU INTERFACE U201E

PAD_IO[53]
PAD_IO[56]
D22
F23
3D_EN 3D_EN AD20 GPIO16 PAD_IO[57] F22
3 M_SDA G21
PAD_IO[58]
C 4 M_SCL 75R/NC 3.3V tolerance only F21 C
PAD_IO[59]
5 CN202 E22
PAD_IO[64]
6 G23
2Pin/2.0mm/NC 1 PAD_IO[65]
NC/CON6-2.0 PAD_IO[66] E23
2 PAD_IO[67] H22
AC1 XTALO H21
XTAL_OUT XTALI PAD_IO[68]
XTAL_IN AD1 PAD_IO[69] G22
3

R105 1k/NC PAD_IO[70] K23

3D_Glasses_PWM 1 J21
Q101 AVDD_DDR AVDD_DDR PAD_IO[71]
J23

MIU1
PAD_IO[72]

MIU0
3904/NC
2

MSD6A628 MR328 MR334

10K 10K RESET0 A15 E21 RESET1
CKE0 PAD_IO[0]/RESET0 PAD_IO[52]/RESET1 CKE1
B15 PAD_IO[22]/CKE0 PAD_IO[74]/CKE1 H23

RESET0 RESET1
Vref0 B19 F24 Vref1
CKE0 CKE1 VREF0 VREF1
B20 C24

SOURCE INPUT MR329

10K
MR333
10K
A24
C25
ZQ0

PAD_IO[26]/TEST
ZQ1

PAD_IO[78]/TEST B24
B25

Close to MST IC
STR PAD_IO[27]/TEST PAD_IO[79]/TEST

with wide trace U201B

MR335 MR330
AVDD_DDR_0 Vref0 240R_1% 240R_1%
33R R234 47nF C206 RIN0
7 VGA-Rin
33R R242 47nF C207 GIN0 RIN0 L3 T3
7 VGA-Gin RIN0P LINEIN_L0 MR1

7 VGA-Bin
7 VGA_HSYNC
改用75R 68R
33R
R239 47nF
R230 47nF
C210 GIN0N
C203 BIN0
VGA_HSYNC
GIN0
GIN0N
BIN0
K1
K2
K3
GIN0P
GIN0M
BIN0P
LINEIN_R0
LINEIN_L1
LINEIN_R1
R3
T2
T1
LINE_IN_1L
LINE_IN_1R
C229
C228
2.2uF
2.2uF
AV1-Lin
AV1-Rin
AV1-Lin
AV1-Rin
7
7
Audio Line Out 1K/1%
MR2
1K/1%
C280
0.1uF
C201
1nF
7 VGA_VSYNC VGA_VSYNC VGA_HSYNC M5
VGA_VSYNC HSYNC0
M4 VSYNC0
LINEIN_L3 V3
LINEIN_R3 W2
M1 RIN1P
L2 GIN1P AVDD_DDR
M3 GIN1M LINEOUT_L0 U3 AVDD_DDR_1 Vref1
M2 BIN1P LINEOUT_R0 V2
MR332 AVDD_DDR J15
1K/1% AVDD_DRAM_A
EARPHONE_OUTL P15 AVDD_DRAM_B 1K 1K
EARPHONE_OUTL W1 MR331 C285 C202
EARPHONE_OUTR 2T 2T
EARPHONE_OUTR W3 1K/1% 0.1uF 1nF
3C 3C
AVDD_DDR_0 A19
AVDD_DDR_1 AVDD_DRAM_A/DECAP
B I2S-MCK F25 AVDD_DRAM_B/DECAP B
I2S_OUT_MCK F7
F8 I2S-BCK
I2S_OUT_BCK C281 C282
33R R232 47nF C213 CVBS0 E8 I2S-WS
7 AV1_IN I2S_OUT_WS 0.1uF 0.1uF
CVBS0 P5 F9 I2S-SDO L202
CVBS0 I2S_OUT_SD 10uH
N4
改用75R 68R R245 47nF C215 VCOM0 N5
CVBS2 All I2S trace need to shield GND EARPHONE_OUTL
C283 C284
VCOM0 CVBS3 EARPHONE-OUTL 7 0.1uF 0.1uF
P6 VCOM
7 CVBS1_OUT CVBS_OUT E7 SPDIF_IN 3D_L/R_FLAG SPDIF_IN固定做3D_LR_Flag输出给6M30 R170
CVBS_OUT SPDIF_IN/3D_FLAG SPDIF_OUT 200R
N6 CVBS_OUT1 SPDIF_OUT E9
C230 C234
33pF 10uF MSD6A628

G12 U1 AUVAG
NC / I2S_IN_WS AU_VAG AUVRM L203
F13 NC / I2S_IN_SD AU_AVSS_VRM U2
E13 10uH
NC / I2S_IN_BCK Close to MSTAR IC EARPHONE_OUTR
EARPHONE-OUTR 7
with width trace
R173
200R
MSD6A628 AUVRM
E-JTAG
C235
10uF I2S-MCK EJ_TRST_N 1
AUVAG TP38
L201 SPDIF_OUT EJ_TDI 1 TP39
C236 I2S-WS EJ_TDO 1
C231 0.1uF TP40
SPDIF_IN EJ_TMS 1
10uF/X7R TP42
I2S-BCK EJ_TCK 1 TP44
FB(1000ohm,200mA) UART-RX1 EJ_RSTZ 1 TP45
I2S-SDO EJ_DINT 1 TP46

EMMC POWER DETECT Mode Selection

C1=C2=2*CL-5 +3.3V_Standby
detect EMMC/NAND Flash Power DEBUG_UART +5V_Standby Crystal RESET CHIP_CONFIG[2:0]
when detect source is from 5V, R204 C204 +5V_Standby
XTALO 0R
C1
30pF R208 NC/4.7K SPI_SDI {PAD_PM_SPI_DI, PAD_LED_R, PAD_PWM_PM}
R235 = 200K, R236 = 51K, R233 = NC R247 R246
2

+12V_Normal +5V_Standby R222 4.7K

3

4.7K 4.7K R207 3 Value Mode Description

NC/1M
Y100 R209 D201
3'b000 SB51_ExtSPI 51 boot from SPI
1

7 UART_TX
UART_TX R214 100R UART-TX 24.000MHz C208 C2 100K BAV99 3'b001 HEMCU_ExtSPI ARM boot from SPI
R225 R226 UART_RX R215 100R UART-RX XTALI 30pF
1K NC/0R 7 UART_RX 3'b010 HEMCU_ROM_EMMC ARM boot from ROM; outer storage is eMMC
1

NOTE:晶体频偏需要小于30PPM C223 3'b011 HEMCU_ROM_NAND ARM boot from ROM; outer storage is NAND
2.2uF
3'b100 DBUS for test only
2

A R210 A
47K 1 Q201
CON5-2.0
3906 +3.3V_Standby reserve for the fourth +3.3V_Standby +3.3V_Standby
R227 R212 HW strapping pin
J104 C224 本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
3

10K 设计电路要求：SAR5正常时电压因为1V。 100R System-RST

1
2
3
4
5

2.2uF
R223 NC/4.7K GPIO_PM0 LED_R R220 4.7K PWM_PM R221 4.7K/NC This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
Power_Detect +3.3V_Normal 根据实际电源 R213 C227
1K R229 SPDIFOUT R626 200RSPDIF_OUT 上电时序调整 100K 1nF R224 NC/4.7K R218 4.7K/NC R219 4.7K Do not spread to third party without the written permission.
7 SPDIFOUT
版权所有@深圳市康冠技术有限公司
M_SCL
M_SDA

D203 R627 75R

R228 Copyright@ ShenZhen KTC Technology Co., LTD
1K NC/ZMM5232B(5.6V)

KTC ISO9001.ISO14001体系文件
EEPROM R/W Port
文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
文件编号： T4270 版本：3.0 页数: 4 of 9
设计: 张志清 审核: 批准:
发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

此Bead 一定要靠近DC-DC输出端！电容靠近IC端！

Heat Sink
AVDDL_MOD S1
VDDC AVDDL_MOD 1
U201F
FOR VB1 R17
L207 0R AVDDL_MOD AVDDL_PREDRV
R18 AVDDL_PREDRV
P18 AVDDL_MOD 2
C251 C288 P19 +3.3V_Standby
AVDDL_MOD Heat-sink45X45mm
0.1uF 1uF DVDD_DDR P20 A12
AVDDL_RX_USB3 AVDD33_LAN AVDD_AU33
P21 AVDDL_TX_USB3 AVDD3P3_DADC A13
AVDD_EAR33 B12
N18 DVDD_DDR AVDD_NODIE B13
N19 DVDD_RX_1
DVDD_DDR N17 E12 AVDD3P3_DMPLL
DVDD_RX_2 AVDD_AU33
D 放到IC背部，预留
C268 0.1uF H24 DVDD_DDR_DECAP D
L208 0R H25 D12
AVDDL_MOD DVDD_RX2_DECAP AVDD3P3_DMPLL AVDD3P3_MPLL
C250 C295 D13
AVDD3P3_MPLL
R20 AVDDL_DVI_PC
0.1uF NC/0.1uF VDDC R19 AVDDL_DVI_PC VDDC_CPU
L17 VDDC
VDDC L18
放到IC背部，减小纹波，一定要上件！ VDDC
L19 VDDC VDDC_CPU U13
J17 VDDC VDDC_CPU U14
M17 VDDC VDDC_CPU V13
C286 C239 C240 C241 C242 C265 C243 C290 C291 M18 V14
VDDC VDDC_CPU
M19 VDDC VDDC_CPU W13
10uF/X7R10uF/X7R 0.1uF 0.1uF 0.1uF 0.1uF 2.2uF 0.1uF/BOT/NC K17 W14
VDDC VDDC_CPU
K19 VDDC
10uF/X7R/BOT/NC K18
Close to MTS IC VDDC_CPU C270 0.1uF P1 VDDC
VDDC/DECAP
W16 VDDC_CPU
W17 AVDD3.3V
VDDC_CPU
U15 VDDC_CPU
U16 VDDC_CPU
U17 VDDC_CPU
V15 VDDC_CPU AVDD3P3_USB F17
V16 VDDC_CPU
V17 F16 VDDP_3318
VDDC_CPU AVDD3P3_DVI
W15 VDDC_CPU
N25 VDDC_CPU/DECAP VDDP_3318 (3.3V/1.8V) A17
P25 VDDC_CPU/DECAP
AVDD_MOD (3.3V) A16
一定要放Test pin！ TP209
TP2091 U12 VSENSE_MIPS AVDD_MOD (3.3V) B16
V12 VSENSE_VSS / (TEST POINT)
VDDP C16
DVDD_NODIE J24 D16
C271 DVDD_NODIE VDDP
VDDP E16
AVDD_PLL D17
1uF C17
AVDD_PLL
L6 GND_EFUSE AVDD_PLL E17
VDDC_CPU H11 B17
放到IC背部，减小纹波，一定要上件！ TESTPIN / (TEST POINT) AVDD_PLL
AVDD_DDR

C287 C249 C274 C267 C266 C269 C273 C275 C289 C292 N13
C272 AVDD_DDR0_D
M13 AVDD_DDR0_C
10uF/X7R10uF/X7R 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF/BOT/NC M14 AVDD_DDR0_D
N14 AVDD_DDR0_D
10uF/X7R/BOT/NC R14
C AVDDL_MOD AVDD_DDR M15
AVDD_DDR1_D C
AVDD_DDR1_C
N15 AVDD_DDR1_D
P14 AVDD_DDR1_D
C277 0.1uF A21
C276 0.1uF AVDD_DDR0_D/DECAP
D25 AVDD_DDR1_D/DECAP
C278 0.1uF K25
C279 0.1uF AVDDL_MOD/DECAP
K24 AVDDL_PREDRV/DECAP
+3.3V_Normal AVDD3.3V VDDP_3318

MSD6A628

C259
C252 C260 C264 C258 C263
U201G
2.2uF
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF

W11
W12
M10
M11
M12
M16

M20

M21
M22
M23
M24

M25

N10
N11
N12
N16
N20
N21
N22
N23
N24

H12

P10
P11
P12
P13
P16
P22

Y10
L10
L11
L12
L13
L15
L16
L20
L21
L22
L23
L24
L25

W4
M7
M8
M9
D9

N2
N3
R4
R5
R6
N7
N8
N9

N1
U4
P2
P3

V4
P8
P9
L9

Close to MTS IC
D23
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

GND

GND
GND
GND
GND

GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
AE17 GND
AE2 GND GND F20
AB10 GND GND G7
AC6 GND GND G8
Standby Power 3.3V A11
A14
GND GND G9
G10
GND GND
A18 GND GND G11
+3.3V_Standby G13
GND
A22 GND GND G14
A23 GND GND G15
B11 GND GND G16
C245 C244 C246 C247 G17
GND
AB24 GND GND G18
2.2uF 0.1uF 0.1uF 0.1uF B14 G19
GND GND
B18 GND GND G20
AA10 GND GND G24
B21 GND GND G25
B22 GND GND H7
+3.3V_Standby AVDD3P3_MPLL B23 H8
GND GND
C10 GND GND H9
C11 GND GND H10
L206 FB C12 H13
C262 GND GND
C13 GND GND H14
C14 GND GND H15
0.1uF C15 H16
GND GND
C18 GND GND H17
+3.3V_Standby AVDD_AU33 H18
GND
B C19 GND GND H19 B
L205 FB C20 H20
C261 GND GND
C21 GND GND J7
GND J8
0.1uF C23 J9
GND GND
D24 GND GND J10
D10 GND GND J11
+3.3V_Standby AVDD3P3_DMPLL D11 J12
GND GND
D14 GND GND J13
DMPLL供电，请用Bead FB (10000hm/200mA) 规格和
电源隔离！ 改善ATV水波纹干扰！ D15 GND GND J14
L209 D18 L14
FB(1000ohm,200mA) C248 GND GND
D19 GND GND J16
P4 GND GND W19
0.1uF D20 J18
GND GND
D21 GND GND J19
AC3 GND GND J20
P7 GND GND J22

+1.5V_DDR AVDD_DDR DDR3 POWER E10

E11
GND GND K7
K8
放到IC背部，减小纹波，一定要上件！ GND GND
E14 GND GND K9
E15 GND GND K10
AC4 GND GND K11
E18 GND
C253 C256 C255 C257 C254 C293 C294 E19 K12
GND GND
E20 GND GND K13
2.2uF 2.2uF 0.1uF 0.1uF 0.1uF 0.1uF/BOT/NC E24 K14
GND GND
AE20 GND GND K15
10uF/X7R/BOT/NC C22
Close to MTS IC GND
D7 GND GND K16
AD6 GND GND Y23
F10 GND GND AB1
F11 GND GND K20
F14 GND GND K21
F15 GND GND K22
F18 GND GND D8
F19 GND GND L7
Y3 L8
GND GND 本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND

GND
GND
GND
GND
GND

GND

GND
GND
GND

This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
Do not spread to third party without the written permission.
R7
R8
R9
R10
R11
R12
R13
R15
R16
P17
R21
R22

T7
T8
T9
T10
T11
T12
T13
T14
T15
T16
T17
T18
T19
T20
T21
T22
U7
U8
U9
U10
W23
W20
W18
U11
T4

U18
U19
U20
U21
U22
U24
V7
V8
V9
V10
V11

V18
V19
V20
V21
V22

V23

W8
W9
W10

版权所有@深圳市康冠技术有限公司
MSD6A628
Copyright@ ShenZhen KTC Technology Co., LTD

A A
KTC ISO9001.ISO14001体系文件

文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
文件编号： T4270
版本：3.0 页数: 5 9 of

设计: 张志清 审核: 批准:

发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

CN401
Panel_VCC
Net to other page Net
40PIN/2.0mm
1 2 R7_RXO0-
GND VCC RXO0- 4 RXO0-
3 4 R6_RXO0+ 4 B0M
GND VCC RXO0+ 4 RXO0+
5 6 R5_RXO1- 4 B0P
NC VCC R4_RXO1+ RXO1- 4
7 GND VCC 8 RXO1+ 4 RXO1-
9 10 R3_RXO2- 4 B1M
GND VCC RXO2- 4 RXO1+
11 12 LVDS_CTL_O R2_RXO2+ 4 B1P
GND P_PWM R1_RXOC- RXO2+ 4
13 GND GND 14 RXOC- 4 RXO2- VBY0N
B3_RXE4- 15 16 B2_RXE4+ R0_RXOC+ 4 B2M
E4- E4+ RXOC+ 4 RXO2+ VBY0P
B3_RXE3- 17 18 B2_RXE3+ G7_RXO3- 4 B2P
E E3- E3+ RXO3- 4 RXOC- VBY1N E
B5_RXEC- 19 20 B4_RXEC+ G6_RXO3+ 4 BCKM
EC- EC+ RXO3+ 4 RXOC+ VBY1P
B7_RXE2- 21 22 B6_RXE2+ G7_RXO4- 4 BCKP
G1_RXE1- E2- E2+ G0_RXE1+ G6_RXO4+ RXO4- 4
23 E1- E1+ 24 RXO4+ 4
G3_RXE0- 25 26 G2_RXE0+
E0- E0+ RXO3- VBY2N
G7_RXO4- 27 28 G6_RXO4+ 4 B3M
O4- O4+ G3_RXE0- RXO3+ VBY2P
G7_RXO3- 29 30 G6_RXO3+ RXE0- 4 4 B3P
O3- O3+ G2_RXE0+ RXO4- VBY3N
R1_RXOC- 31 32 R0_RXOC+ RXE0+ 4 4 B4M
OC- OC+ G1_RXE1- RXO4+ VBY3P
R3_RXO2- 33 34 R2_RXO2+ RXE1- 4 4 B4P
O2- O2+ G0_RXE1+
R5_RXO1- 35 36 R4_RXO1+ RXE1+ 4
O1- O1+ B7_RXE2-
R7_RXO0- 37 38 R6_RXO0+ RXE2- 4
O0- O0+ B6_RXE2+ RXE0-
39 40 RXE2+ 4 4 A0M
GND GND B5_RXEC- RXE0+
RXEC- 4 4 A0P
+3.3V_Normal B4_RXEC+
B3_RXE3- RXEC+ 4 RXE1-
RXE3- 4 4 A1M
B2_RXE3+ RXE1+
RXE3+ 4 4 A1P
B3_RXE4-
B2_RXE4+ RXE4- 4 RXE2-
RXE4+ 4 4 A2M
RA2 RXE2+
接到12PIN 4 A2P
1K
RXEC-
4 ACKM
LVDS_CTL_O RA3 1K RXEC+
4 ACKP
3

QA2 4.7K RXE3-

4 A3M
LVDS CC1
2.2uF/NC
1 RA1 BRI_ADJ 3,4 4 A3P
RXE3+
RXE4-
3904 4 A4M
RXE4+
2

4 A4P

D D

TDA18275HN +3.3V_TU TR7 1K

DEMOD_IF_AGC
+3.3V_TU
TR6 1K IF-AGC

TC22 TC16

6.8NF 6.8NF

TU3
TDA18275HN/N1
33
32
31
30
29
28
27
26
25

RF SIGNAL INPUT
AGCA
VCCRF

GNDIF
VCCIF
GPO1

GPO2

TESTI3
GND

AGCD

TUNER_CONNECTOR TC14 0.1uF

IF-IN-
CON1 TC17 220PF TC23 82PF 1 24
RFG IFOAN TC15 0.1uF
1 RF-IN RF_IN# 2 23 IF-IN+
RFIN IFOAP
2 3 22
330nH 140mA 5%

RFG IFODN
3 4 TESTO1 IFODP 21
4 5 XTSEL CAPVCO 20
TC4 6 TESTO2 VCCPL 19 +3.3V_TU
TL2

7 GNDDIG GNDPL 18 TC6

150pF 8 17
470nH AS XTOUT
TESTI1

TESTI2
XTALN

0.1uF
XTALP
SDA
SCL

CP
VT

C DIF IN&OUT C
TL1

9
10
11
12
13
14
15
16

220nH 120mA
IF-IN- R841 0R VIFM DIF2 4
9 IF-IN- C821
47pF
TC10 6.8NF
XTAL_P
IF-IN+ R840 0R VIFP DIF1 4
XTAL_N TR5 220R 9 IF-IN+
TC11 150NF C822
TC7 47pF
+3.3V_TU TC9 TC8
30pF 30pF 6.8NF

TY1 16MHz

TC18 TC19 TC20 TC21 Close Tuner

47NF 47NF 0.1uF 0.1uF
SDA-T TR1 100R T_SDA 4 IF-AGC R1015 100R IF_AGC_T 4
SCL-T TR2 100R T_SCL 4 C1021
0.1uF
R1016
0R/NC
TC12 TC13
30pF 30pF
DEMOD_IF_AGC 9
AGC RC Filter
B B

+3.3V_Normal
NF_POWER
iNAND FLASH R1104 0R

C1105 C1106 C1107 C1110

U1101 C1101 C1102 2.2uF 0.1uF 0.1uF
NF_CLK W6 J3 NF_D4
CLK D4 0.1uF 2.2uF
C1109 NF_CMD W5 J4 NF_D5
CMD D5 2.2uF
NC/33pF NF_D0 H3 J5 NF_D6
NF_D1 D0 D6 NF_D7
H4 D1 D7 J6
NF_D2 H5
NF_D3 D2 NF_RSTZ
J2 D3 RESET U5

NF_POWER K6 VDD_IF VDD M6 NF_POWER

W4 N5
iNAND

VDD_IF VDD
Y4 VDD_IF VDD T10
AA3 VDD_IF VDD U9
AA5 VDD_IF
VSS M7
K4 VSS VSS P5
Y2 VSS VSS R10
Y5 VSS VSS U8 NF_CLK R1101 10R EMMC_CLK
EMMC_CLK 4
本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
AA4 NF_CMD R1102 0R EMMC_CMD
AA6
VSS
K2 NF_RSTZR1103 0R EMMC_RSTZ
EMMC_CMD 4 This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
VSS CREG/VDDi EMMC_RSTZ 4
iNAND
C1108 2.2uF Do not spread to third party without the written permission.
NF_D0RP1101 0RX4 EMMC_D0
NF_D4 EMMC_D4
NAND_RBZ 4 版权所有@深圳市康冠技术有限公司
1 3 5 7

2 4 6 8

A NAND_REZ 4 A
NF_D6 EMMC_D6 Copyright@ ShenZhen KTC Technology Co., LTD
NAND_CEZ 4
NF_D7 EMMC_D7
NAND_CE1Z 4
NF_D5 EMMC_D5
NF_D1 EMMC_D1
NAND_CLE 4 KTC ISO9001.ISO14001体系文件
1 3 5 7

2 4 6 8

NAND_ALE 4
NF_D3 EMMC_D3
NAND_WEZ 4
NF_D2 EMMC_D2
RP1102 0RX4
NAND_WPZ 4
文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
文件编号： T4270 版本：3.0 页数: 6 of 9
设计: 张志清 审核: 批准:
发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

USB INTERFACE
USB ESD分布电容要求<2pF
CON601 CN207
VGA

16
1 5V_USB_WIFI
2 R17 100R/NC WIFI_EN 4
11 1 VGA-Rin VGA-Bin
VGA-Bin 4 3 USB0_D-
6 VGA-Gin USB0_D- 4
VGA-Gin 4 4 USB0_D+
12 2 VGA-Gin VGA-Rin USB0_D+ 4
VGA-Rin 4 5
7
13 3 VGA-Bin
8 R616 R621 R620 CON5-2.0mm
14 4 75R 75R 75R
9
15 5
D
10 VCC 1 5V_USB1 D
USB1_D-
Close to Mstar IC D- 2
3 USB1_D+ USB1_D- 4
VGA

17
D+ USB1_D+ 4
GND 4
AV1 AV1_IN 4
SHIELD 5
DDC_SCL_D UART_RX 4 6
AV1_IN

AV1-AuLin R534 10K AV1-Lin 4 SHIELD

DDC_SDA_D UART_TX 4
AV1-AuRin R535 10K CN317 USB_4P
AV1-Rin 4 100R R622 VGA_VSYNC 4
100R R617 VGA_HSYNC 4

R536 R537R538
R615 R618
CN307 12K 12K 75R
Close to Mstar IC 10K 10K
D625 D627 D628 D629

2
AV1-IN NC NC NC NC

1
VIDEO-OUT/YELLOW Close to Mstar IC
Coaxial
CN315
CN314
1 AVOUT-V R415 0R
1 SPDIFOUT 4 CVBS1_OUT 4
2
2 R410
ED3 75R
1pF C401
100pF

C
Coaxial OUT AV-OUT CON602
USB3-A/USB3.0
USB3.0
C

VBUS 1 5V_USB3
D- 2 USB3_D- 4
R274 0R 3
HP_MUTE SHUTDOWN D+ USB3_D+ 4
+12V_NORMAL 4
AMP_12V GND
AMP_12V STDA_SSRX- 5 USB3_SSRXN 4
3

STDA_SSRX+ 6 USB3_SSRXP 4
R273 10k AMP_12V 7
4 AMP-MUTE 1 Q26 R261 GND_DRAIN
8 C616 0.1uF
3904 1K STDA_SSTX- USB3_SSTXN 4
L:ON L204 9 C615 0.1uF
R275 +5V_Normal STDA_SSTX+ USB3_SSTXP 4
2

H:MUTE SHELL 10
4.7k R238 D205 0805_BEAD AMP_12V1 11
R268 100k/nc SHELL
L210
1N4148 C169 C321 C317
10K
R248 C221
0805_BEAD D626 D636 D634 D635 D632 D633
10K R267 100k 1nF 100nF 10uF/16V

2
470uF
+3.3V_Standby
L:SHUTDOWN
1

C296
R236
D204 1N4148 Q206
28
27

R4 10R/NC C4 330PF/NC NC NC NC NC NC NC

1
100uF/16V 100k U202
3 2
3906 SD 1
PVCCL
PVCCL

SD L5
C322 0.22UF
2 FAULT BSPL 26
CN203
C319 0.47uF 22UH/600欧磁珠4A
4 EARPHONE-OUTL LIN_P 3 25 OUTPL C316 +5V_Normal
LINP OUTPL LOUT+
0.47UF 2
LIN_N 4 24
LINN PGND LOUT-
R258 10k/NC C320 0.47uF 1 6V/1.1A L403
GAIN0 5 23 OUTNL 5V_USB_WIFI
R249 10k GAIN0 OUTNL +5V_Normal 5V_USB3
L10 C318
C297 0.22UF C603
GAIN1 6 22 0.47UF
GAIN1 BSNL R1 10R/NC C2 330PF/NC
AMP_12V R255 10R R250 10k 22UH/600欧磁珠4A C619 10uF
AVCC 7 AVCC 0.1uF
Q14 AO3401
B C142 C165 8 22UH/600欧磁珠4A R2 10R/NC C3 330PF/NC 6V/1.1A L404 B
AGND C299 0.22UF 5V_USB1
100nF BSNR 21
10uF/16V GVDD 9 C604 C68 R59
GVDD L14
20 OUTNR C315 100K
OUTNR CN201
PLMIT 10 0.47UF C618 10uF 1uF
PLIMIT ROUT- 0.1uF USB3_ON C51 C61
C298 PGND 19 1 -
R240 10k RIN_N 11
C323 RINN OUTPR 0.1uF 10uF
1uF OUTPR 18 2 GND
1uF RIN_P 12 L23 C314 R45
RINP C300 0.22UF
17 0.47UF ROUT+ 3 10K
BSPR +
13
PVCCR
PVCCR

NC 22UH/600欧磁珠4A
C226 0.47uF
TAB

3Pin/2.0mm Note:电容靠近USB)端子,提供usb读写稳定性
14 PBTL R5 10R/NC C5 330PF/NC

3
4 EARPHONE-OUTR Q13
C225 0.47uF TPA3110LD2 4 USB3_EN R47 4.7K1
29

15
16

AMP_12V1
H :Power on
L :Power off R44

2
10K 3904

C175 C222
C1
USB POWER
10uF/16V
1nF 100nF
AUDIO AMP
功放放大倍数调节
EARPHONE OUT C327
GAIN1(PIN6) GAIN0(PIN5) AMP GAIN(db) 本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
R271
A HP/BLUE Do not spread to third party without the written permission. A
47k
1nF
0 0 20
CN22 5
4 E_AMP-L
C326 10uf
EARPHONE-OUTL 4
版权所有@深圳市康冠技术有限公司
2
E_AMP-R
C329 10uf Copyright@ ShenZhen KTC Technology Co., LTD
1 EARPHONE-OUTR 4 0 1 26
3
KTC ISO9001.ISO14001体系文件
6

R272 C328 1 0 32
47k 文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
1nF 1 1 36
HP_MUTE
文件编号： T4270 版本：3.0 页数: 7 of 9
设计: 张志清 审核: 批准:
发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

HDMI1(ARC)
CON801
1 HDMI1_RX2P HDMI1/5V
DATA2+
DATA2 SHIELD 2
3 HDMI1_RX2N HDMI1_RX2P HDMI1-RX2P HDMI1/5V
DATA2- HDMI1-RX2P 4
4 HDMI1_RX1P R802
DATA1+ HDMI1_RX2N HDMI1-RX2N R805
DATA1 SHIELD 5 HDMI1-RX2N 4
6 HDMI1_RX1N HDMI1_RX1P HDMI1-RX1P
DAT1A- HDMI1-RX1P 4
7 HDMI1_RX0P R803 R804
DATA0+ HDMI1_RX1N HDMI1-RX1N 1K
DATA0 SHIELD 8 HDMI1-RX1N 4
9 HDMI1_RX0N HDMI1_RX0P HDMI1-RX0P HDMI1-HPD
DATA0- HDMI1-RX0P 4
10 HDMI1_CLKP 10K
CLK+

3
11 HDMI1_RX0N HDMI1-RX0N Q801
CLK SHIELD HDMI1-RX0N 4
12 HDMI1_CLKN HDMI1_CLKP HDMI1-CLKP HDMI1-DDC-SCL 10K 10K R801 33R 1R807 10K HDMI1-HPDIN
D CLK- HDMI1-CLKP 4 HDMI1-SCL 4 HDMI1-HPDIN 4 D
20 13 CEC HDMI1-DDC-SDA R806 33R
GND1 CEC HDMI1-SDA 4
21 14 HDMI1_ARC HDMI1_CLKN HDMI1-CLKN 3904
HDMI1-CLKN 4

2
GND2 NC HDMI1-DDC-SCL
22 GND3 SCL 15
23 16 HDMI1-DDC-SDA
GND3 SDA
DDC/CEC GND 17
+5V POWER 18 HDMI1/5V
19 HDMI1-HPD
HOT PLUG

HDMI/90D

HDMI2
HDMI2/5V

CON802
1 HDMI2_RX2P HDMI2/5V R808
DATA2+ HDMI2_RX2P HDMI2-RX2P R809
DATA2 SHIELD 2 HDMI2-RX2P 4
3 HDMI2_RX2N
DATA2- HDMI2_RX1P HDMI2_RX2N HDMI2-RX2N
DATA1+ 4 HDMI2-RX2N 4
5 HDMI2_RX1P HDMI2-RX1P R810 R811 1K
DATA1 SHIELD HDMI2-RX1P 4
6 HDMI2_RX1N HDMI2-HPD
DAT1A- HDMI2_RX0P HDMI2_RX1N HDMI2-RX1N 10K
DATA0+ 7 HDMI2-RX1N 4

3
8 HDMI2_RX0P HDMI2-RX0P Q802
DATA0 SHIELD HDMI2-RX0P 4
9 HDMI2_RX0N 1R814 10K HDMI2-HPDIN
DATA0- HDMI2-HPDIN 4
10 HDMI2_CLKP HDMI2_RX0N HDMI2-RX0N HDMI2-DDC-SCL 10K 10K R812 33R
CLK+ HDMI2-RX0N 4 HDMI2-SCL 4
11 HDMI2_CLKP HDMI2-CLKP HDMI2-DDC-SDA R813 33R 3904
HDMI2-CLKP 4 HDMI2-SDA 4

2
CLK SHIELD HDMI2_CLKN
CLK- 12
20 13 CEC HDMI2_CLKN HDMI2-CLKN
GND1 CEC HDMI2-CLKN 4
21 GND2 NC 14
22 15 HDMI2-DDC-SCL
GND3 SCL HDMI2-DDC-SDA
23 GND3 SDA 16
C DDC/CEC GND 17 C
+5V POWER 18 HDMI2/5V
19 HDMI2-HPD
HOT PLUG

HDMI/90D

HDMI3(MHL)
CON803 +5V_Standby
1 HDMI3_RX2P
DATA2+ R850 0R MHL_CD_SENSE
DATA2 SHIELD 2
3 HDMI3_RX2N HDMI3_RX2P HDMI3-RX2P
DATA2- HDMI3-RX2P 4
4 HDMI3_RX1P HDMI3_RX2N HDMI3-RX2N
DATA1+ HDMI3-RX2N 4
5 HDMI3_RX1P HDMI3-RX1P R816 R817
DATA1 SHIELD HDMI3-RX1P 4
6 HDMI3_RX1N HDMI3_RX1N HDMI3-RX1N
DAT1A- HDMI3-RX1N 4
7 HDMI3_RX0P HDMI3-HPD R852 33R HDMI3-HPDIN
DATA0+ HDMI3-HPDIN 4
DATA0 SHIELD 8
9 HDMI3_RX0N HDMI3_RX0P HDMI3-RX0P 10K 10K
DATA0- HDMI3-RX0P 4
10 HDMI3_CLKP HDMI3-DDC-SCL R819 33R
CLK+ HDMI3-SCL 4
11 HDMI3_RX0N HDMI3-RX0N HDMI3-DDC-SDA R820 33R
CLK SHIELD HDMI3-RX0N 4 HDMI3-SDA 4
12 HDMI3_CLKN
CLK- CEC HDMI3_CLKP HDMI3-CLKP
20 GND1 CEC 13 HDMI3-CLKP 4
21 14 HDMI3_CLKN HDMI3-CLKN
GND2 NC HDMI3-CLKN 4
22 15 HDMI3-DDC-SCL
GND3 SCL HDMI3-DDC-SDA
23 GND3 SDA 16
DDC/CEC GND 17
+5V POWER 18 HDMI3/5V
19 HDMI3-HPD
HOT PLUG

HDMI/90D

B B

CEC & ARC +5V_Normal

HDMI3/5V

R849 100R QA801

MHL_CD_SENSE
MHL_Cable_DET 4
HDMI1_ARC C801 HDMI-ARC VOUT 5
HDMI1-ARC 4 3 1
2.2uF IN VOUT
R848 HDMI3/5V AVDD5V_MHL

GND
C802 R854 0R
CEC R822 200R 300K 4 C803
HDMI-CEC 4 47nF 4 MHL_Cable_DET EN
R851 10R 10uf/6.3V
R824 10K R823 4.7K SGM2554A

2
HDMI1/5V

HDMI1-ARC_DET 4
MHL
HST-0041 R657 75R/1%
U651
MDI_TP CN309
4 MDI_TP 1 TD+
TX+ 16 1 TD+
2 TCT NC 7
TX- 14 2 TD-
MDI_TN 3
4 MDI_TN TD- R660 75R/1%
4 NC1 TCM 15 4 TDCT CH_GND 8
NC4 13
5 R662 75R/1% 5
MDI_RP NC2 RDCT
6 12 13
4 MDI_RP RD+ NC3
11 3
NC1
14 本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
RX+ RD+ NC2
A
7 RCT This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only, A
9 6
MDI_RN 8
RX- RD- Do not spread to third party without the written permission.
4 MDI_RN RD- R664 75R/1%
10 12 11
TCM- GND1 GND2 版权所有@深圳市康冠技术有限公司
SMDTR16P CB652 Copyright@ ShenZhen KTC Technology Co., LTD
C653 C654 10 9
1nF/2KV GND3 GND4
0.1uF 0.1uF KTC ISO9001.ISO14001体系文件
RJ45-W

LAN 文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图

文件编号： T4270 版本：3.0 页数: 8 of 9
设计: 张志清 审核: 批准:
发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1
 5 4 3 2 1

VDD33
VDD
+3.3V AVDD33 VDD33 +1.15V VDD C23 XTAL_IN
30pF +3.3V
Close to Demod.
Y1 RESETn

TS_VLD
TS_D0
TS_D1
TS_D2
TS_D3
TS_D4
TS_D5
D_SDA

44 TS_SYNC
3 R22

C22 C24 C25 C26 C27 C30 C31 C33 XTAL-24MHz 1M R30
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10K
0.1uF 0.1uF 0.1uF C29 R23 XTAL_OUT
U4

48
47
46
45

43
42
41
40
39
38
37
30pF 0R
Demod_RST
Close to Demod.

VDD
GND

TS_SYNC
TS_VLD
I2CS_SDA

VDD33

TS_D0
TS_D1
TS_D2
TS_D3
TS_D4
TS_D5
C38

10uF/6.3V

+3.3V
D D_SCL 1 I2CS_SCL TS_D6 36 TS_D6 D
TS_D7
4

U3 2 GND TS_D7 35
R24 XTAL_OUT 3 34 TS_CLK
R26 10K/NC XTAL_IN XTAL_OUT TS_CLK MSPI_CSZ
4 XTAL_IN MSPI_CSZ 33
AMS1117-1.2 AVDD33 5 32 MSPI_DO
+3.3V_TU 0R AVDD33 MSPI_DO
ADJ

OUT

T_IF_AGC 6 MSB102KT 31 MSPI_DI

L211 FB +3.3V 6 DEMOD_IF_AGC IFAGC_S MSPI_DI
IN

T_IF_AGC 7 30
C34 IP_T IFAGC_T GND Demod_RST
8 IP_T RESETZ 29
+1.15V IM_T MSPI_CLK H/W Strap
1

9 IM_T MSPI_CLK 28 TS_ERR

+5V_Normal C63 C60 C43 C44 22nFClose to Demod. 10 GND VDD33 27 VDD33
11 IP_S GND 26 R34

DISEQ_IN1/TS_ERR
0.1uF 10uF/6.3V 0.1uF 10uF/6.3V 12 25 VDD I2C slave address:
IM_S VDD
C57 TS_ERR=0, I2C slave address=0xD2 NC/10K
C41 C62 TS_ERR=1, I2C slave address=0xF2

DISEQ_OUT1
C42 C45 DIF2 C39 0.1uF IP_T 如果TS_ERR(PIN24)悬空,默认为上拉
6 IF-IN+

I2CM_SDA
I2CM_SCL
0.1uF 0.1uF 则address=0xF2。

AVDD33
2.2uF 10uF/6.3V 2.2uF DIF1 C40 0.1uF IM_T

VDD33
GPIO0
6 IF-IN-

QM_S
QP_S

GND

GND
VDD
MSB102X DEMOD core power 电压1.10V~1.20V Configure

13
14
15
16
17
18
19
20
21
22
23
24
DISEQ_OUT1
MSB102X DTMB DEMOD core power
电流MAX 600mA，需要DCDC。其他demod For MSB1400,
must use Xtal turbo mode, pin19=1 R32
core power电流MAX350MA，可以用LDO。

Configure
U6 上件说明： (Default with internal pull-up)

TS_ERR
NC/10K
1. 当U4为ISDBT/DTMB/S2 DEMOD chip时,U5 、R25、C32要 NC。
1. 当U4为DVBT/T2 DEMOD chip时,U5 、R25、C32要 上件。
TS_D0

VDD33
VDD
AVDD33
4 Demod_RST Demod_RST +3.3V
TS_D1 +3.3V +3.3V
TS_CLK
TS_D2 4 TS_CLK TS_VLD GD25Q10T
TS_D3 4 TS_VLD TS_SYNC U5
TS_D4 4 TS_SYNC R27 100R C32
TS_D5 3,4 M_SDA D_SDA R31
R25 MSPI_CSZ 1 8
TS_D6 R28 100R CE# VDD NC/0R
3,4 M_SCL D_SCL 10K
TS_D7
MSPI_DO 2 7 0.1uF
SO HOLD# For MSB101X, DISEQ_OUT1
TS_D[0:7] CONNECT 3.3V
4 TS_D[0:7] MSPI_WP 3 6 MSPI_CLK
WP# SCK
4 5 MSPI_DI
VSS SI

DVB-T2 采用1Mbit的Flash.
C C

PCMCIA PCMCIA POWER

VCC-PCMCIA CON1051 VCC-PCMCIA
PCMCIA_CNT
35 GND GND 1
PCM_CD1_N 36 2 PCM_D3
TS_MDO3 CD1# D3 PCM_D4
37 MDO3 D4 3
TS_MDO4 38 4 PCM_D5
TS_MDO5 MDO4 D5 PCM_D6 VCC-PCMCIA
39 MDO5 D6 5
TS_MDO6 40 6 PCM_D7
TS_MDO7 MDO6 D7 PCM_CE_N
41 MDO7 CE1# 7
42 8 PCM_A10 VCC-PCMCIA
CE2# A10 PCM_OE_N +5V_Normal
43 VS1# OE# 9
PCM_IORD_N 44 10 PCM_A11 R1082 L1052 0R
PCM_IOWR_N IORD# A11 PCM_A9 4.7K
45 IOWR# A9 11
4 TS_SYNC 46 12 PCM_A8
TS_D0 MISTRT A8 PCM_A13
47 MDI0 A13 13
TS_D1 48 14 PCM_A14
TS_D2 MDI1 A14 PCM_WE_N
49 MDI2 WE# 15
TS_D3 50 16 PCM_IRQA_N
VCC-PCMCIA MDI3 READY
51 VCC VCC 17
52 VPP2 VPP1 18
TS_D4 53 19 C1065 C1068
TS_D5 MDI4 MIVAL TS_VLD C1067
4
54 MDI5 MICLK 20
R1079 TS_D6 PCM_A12 TS_CLK 4
55 MDI6 A12 21
4.7K TS_D7 56 22 PCM_A7 0.1uF
TS_MOCLK MDI7 A7 PCM_A6 10uF 10uF
57 MOCLK A6 23
PCM_RESET 58 24 PCM_A5
PCM_WAIT_N RESET A5 PCM_A4
59 WAIT# A4 25
60 26 PCM_A3
C1066 PCM_REG_N INPACK A3 PCM_A2
61 REG# A2 27
TS_MOVAL 62 28 PCM_A1
NC/10pF TS_MOSTART MOVAL A1 PCM_A0
63 MOSTART A0 29
TS_MDO0 64 30 PCM_D0
TS_MDO1 MDO0 D0 PCM_D1
65 MDO1 D1 31
B TS_MDO2 66 MDO2 D2 32 PCM_D2 B
PCM_CD2_N 67 33
GND
GND
GND
GND

CD2# WP
68 GND GND 34
CARD DETECT
72
71
70
69

+5V_Normal

PCM_CD_N
PCM_RESET PCM_CD_N 4 PCM_CD1_N PCM_CD2_N PCM_CD_N
PCM_RESET 4 R1078 R1077
PCM_WAIT_N
PCM_WAIT_N 4 1K 1K
PCM_REG_N GND GND L 0V
PCM_OE_N PCM_REG_N 4
PCM_OE_N 4 PCM_CD1_N R1075 10K PCM_CD_N
TS_MDO[7:0] TS_MDO[7:0] 4 PCM_WE_N NC H 2.5V
TS_MDO0 PCM_IORD_N PCM_WE_N 4 GND
TS_MDO1 PCM_IOWR_N PCM_IORD_N 4
TS_MDO2 PCM_CE_N PCM_IOWR_N 4
PCM_CE_N 4 PCM_CD2_N R1076 10K C1063 NC GND H 2.5V
TS_MDO3 PCM_IRQA_N
TS_MDO4 PCM_IRQA_N 4
PCM_A[14:0] 1nF NC NC H 5V
TS_MDO5
TS_MDO6 PCM_A[14:0] 4
TS_MDO7 PCM_D[7:0]
PCM_D[7:0] 4

TS_MOCLK 4 TS_D[0:7] 4
TS_MOSTART 4
TS_MOVAL 4

本文档仅限中国深圳市康冠技术有限公司和被呈送方内部使用，未经书面许可请勿扩散到第三方。
This document for ShenZhen KTC Technology CO., Ltd and presented party internal use only,
Do not spread to third party without the written permission.
版权所有@深圳市康冠技术有限公司
Copyright@ ShenZhen KTC Technology Co., LTD

A A
KTC ISO9001.ISO14001体系文件

文件名称： MSD6A628方案T8E3(DVB-T/T2/C)数模一体智能电视原理图
文件编号： T4270 版本：3.0 页数: 9 9 of

设计: 张志清 审核: 批准:

发行部门： 研发处 生效日期： Friday, February 06, 2015
5 4 3 2 1