INSTITUTIONAL ASSESSMENT

HEO FORKLIFT NC II

TEST I
Instruction: Multiple choice
1. During the operation why it is important to always monitor the load?
a. To stop the load hitting into the object and for the safety of other people
b. To check the weight of the load
c. To check the size of the load
d. To monitor the quantity of the load

2. When the forklift is loaded explain why it is unsafe to turn the forklift on a sloping surface?
a. Load become unstable and could tip over
b. People around may be hit by the forks
c. Load may be drop during traveling
d. Load is concentrated on the front wheels
3. Procedure you may implement if you are involve in roller over or tip over?
a. Jump immediately
b. Remain in the forklift and brace your self
c. Just wait what happen next
d. Call your supervisor for help
4. Is all weight from the front wheel to the back of the forklift act as counter weight?
a. Yes
b. No
5. Are you permitted to add extra counter weight of the forklift?
a. No
b. Yes
6. How could you park your forklift in inclined?
a. Park in normal and choke the wheels
b. Park facing downward
c. Park with the fork 5 cm above the ground
d. Just leave your forklift and call your supervisor
7. Why you need to remove the key when the forklift not in use?
a. So that it may not be stolen
b. To prevent people which are not qualified to use the forklift
c. Keep it and bring tomorrow morning
d. To make an duplicate
8. Can anyone hitch the lift truck in any ways?
A. Absolutely not recommended
B. If necessary
C. With the order of supervisor
D. No one is watching you
9. Low tire pressure has NO effect on handling on tire life
A. True
B. False
10. What is the reason why forklift have bigger tires in front
A. To balance the load against the counter weight
B. Fulcrum is located in front tires
C. Load concentrate in front wheels
D. Load is heavier than the counterweight
11. How do you travel down the slope with load?
a) Forward
b) Reverse
c) Drive faster
d) Drive with load high mask
12. What is load center?
a) Distance between the center of the load and root of the forks
b) Distance from root of forks to the middle of the forks
c) Center of load
d) Center of the forks
13. What is the warming time for engine before productive operation?
a) 30-50 minutes
b) 10-15 minutes
c) 3-5 minutes
d) 7-10 minutes
14. Where is the steering operation of forklift?
a) Front left wheel
b) Front right wheels
c) Rear axle
d) None of the above
15. What is the function of overhead guard?
a) Protect the operator from falling object and tip over
b) Protect the operator from rain
c) Protect the operator from sunlight
d) None of the above
16. What part of forklift is responsible in raising and lowering the forks?
a) Tilt cylinder
b) Lift cylinder
c) Carriage
d) Accelerator
17. What is the procedure in travelling with load?
a) Load tilted backward
b) Load tilted forward
c) Travel with maximum speed
d) Travel with your friend beside you
18. What is the used of front tires?
a) Act as balancer between counter weight and the load
b) Front wheels is used to travel the load
c) Center of gravity
d) Load center of forklift
19. What are the criteria in checking the engine oil?
a) Check if the oil is full
b) Check the presence, level and color of the oil
c) check if the dipstick if ok
d) check the engine oil while the engine is running
20. What is the used of thermostat?
a) Maintain the temperature of the engine
b) Check the temperature if overheated
c) Can help for long life span of the equipment
d) All of the above
TEST II
Instruction: Fill in the blanks, Select the answer from the list provided.
1. ______________ is a device that stops particles that are present in the air from entering air- breathing
machinery.
2. ______________ is the amount of time that the machine should be allowed to kept in low idle before and after
operation in order to safeguard the lubrication of the turbo charger.
3. ______________ is the system that the task is to remove the heat from the engine by the force circulation of the
coolant, thereby preventing the engine from overheating. This system will include the radiator, water pump,
water jacket and thermostat.
4. After operating the service unit, you need to look for ___________ ground where you can park the equipment in
preparation for the next day operation and this is the area where you can perform inspection.
5. _____________ safety devices of forklift that can protect the operator from falling loads from the front.
6. ____________ is the equivalent of two unit of battery used in electrical system for the EQUIPMENT.
7. ____________ is the device that can convert mechanical energy for charging the battery. This also known as the
a/c generator.
8. If any ______________ develops along the battery terminal, this may interfere with the connections and the
vehicle may have trouble starting. This can cause corroded or even loose battery terminals.
9. ____________ the primary requirements in occupational safety and health that can protect the workers.
10. The _____________ is used to transfer rotational power from one place to another in the engine.
11. ______________ should be perform by the operator prior of operation to ensure the equipment is operational
and is safe to use.
12. _____________ is a form of lubricating oil to which a thickening agent has been added, lack of this may result
damage to parts due to metal to metal contact.
13. _____________Is a device that is attached or located on the fuel line, and the task is to remove the dirt and
other contaminants form the passing fuel.
14. ___________ is a device where electrical energy has been stored and this device has positive and negative
terminal.
15. _____________ is a part of forklift which protect the operator from falling load or object or from tip over.
16. _____________ is a device that is used to know the operation hour of the equipment.
17. _______________ serve as the storage area for the hydraulic oil in the hydraulic system.
18. _______________ is the state of being safe, freedom from accident.
19. Serve as the balancer of the forklift between the load and the _____________.
20. ______________ is used for lifting and moved or load and unload palletize material.

SELECT ANSWER FROM THIS BOX

CORROSION AIR CLEANER COLLING SYSTEM

SAFETY CONTROL LEVER PRE & POST INSPECTION

FORKLIFT LEVEL & FIRM OVERHEAD GUARD

GREASE HOUR METER COUNTER WEIGHT

CRANE BACKREST HYDRAULIC TANK

12 VOLTS FAN BELT DIESEL

BATTERY FUEL FILTER 24 VOLTS

ALTERNATOR 3-5 MINUTES PPE