SPEC SHEET

CATALOG

BELT
CONVEYOR
U l t i m a t i o n I n d u s t ri e s LLC
15935 S t u rg e o n S t.
Ro s ev i l l e, M I 48 066
Ph. +1- 586 -771-1881
u l t i m a t i o n i n c.co m
 n All safety guarding to be safety yellow unless
otherwise specified.
n Other items available, please contact factory.
n Other colors available on request

Standard Paint Colors

Colors illustrated below may vary slightly from actual paint colors.

R
H OU OR
L
48 CO
I P
SH

Conveyor Blue Safety Blue Machinery Grey Safety Orange Gloss White
110549 110552 110652 110559 111232
RAL-5019 RAL-7011 RAL-2010 RAL-9003

Dark Green Conveyor Gray Safety Yellow Light Ivory Conveyor Green
110555 110554 115174 115886
RAL-6005 RAL-1023 RAL-1015

Gloss Black Dark Blue Light Blue Sky Blue

111233 114815 RAL-5012 RAL-5015
RAL-9005
(Textured black available)

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

TABLE OF CONTENTS
BELT CONVEYORS
Horizontal belt conveyor ............................................................... 1-8
Belt curve .........................................................................................9
Incline belt conveyor ..................................................................10-13
Incline dimensional chart ................................................................14
Bed and undertrussing information .................................................15
Troughed belt conveyor..............................................................16-19

LIVE ROLLER CONVEYORS

Belt driven live roller conveyor (transportation) ..........................20-21
Belt driven live roller conveyor (minimum pressure) ...................22-23
Belt driven live roller conveyor (zero pressure) ...................... 23A-23B
Flat motor conveyor (transportation) ..................................... 23C-23E
Flat motor conveyor (zero pressure) ...................................... 23F-23H
V-belt driven live roller conveyor (minimum pressure) ................24-39
Lineshaft conveyor .....................................................................40-43
Chain driven live roller conveyor (transportation) .......................44-54

CHAIN CONVEYORS
Drag chain conveyor (transportation) .........................................55-58

GRAVITY CONVEYOR
Skatewheel conveyor .................................................................59-61
Gravity roller conveyor ...............................................................62-72
Ball transfer table ...........................................................................73
Conveyor rail................................................................................... 74

ACCESSORIES
Supports ....................................................................................75-78
Guide rails ...................................................................................... 79
Stops .........................................................................................80-82
Gates .........................................................................................83-84

ELECTRICAL CONTROLS
ProLogic Accumulation System ..................................................85-86

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

BS100B
HORIZONTAL BELT CONVEYOR
(Slider Bed)
The BS100B belt conveyor is ideal for transporting packages
of various sizes and shapes. It can be used in many types of
material handling application such as assembly operations,
sorting, packaging, and inspection or for simply transporting
product from point A to B.
n Smooth, slim design
n Coped ends
n 10 belt widths
n Multiple belt options

CONVEYOR WEIGHTS (LBS.)

OVERALL BELT WIDTH
LENGTH 6" 8" 10" 12" 14" 16" 18" 20" 24" 30"
OVERALL BED
WITH
LENGTH LENGTH BED WIDTH
CENTER
DRIVE 10" 12" 14" 16" 18" 20" 22" 24" 28" 34"

6' 5' 6' 220 236 252 268 284 300 316 332 363 403
4 IN. DIA. DRIVE PULLEY

11' 10' 11' 265 285 305 325 345 365 385 405 445 501
16' 15' 16' 300 324 348 372 395 419 443 467 514 588
21' 20' 21' 345 373 401 429 456 484 512 540 596 686
26' 25' 26' 380 412 444 476 506 538 570 602 665 773
31' 30' 31' 425 461 497 533 567 603 639 675 747 871
36' 35' 36' 463 502 541 580 619 658 697 736 816 958
41' 40' 41' 508 551 594 637 680 723 766 809 898 1,056
46' 45' 46' 543 590 637 684 730 777 824 871 967 1,143
51' 50' 51' 588 639 690 741 791 842 893 944 1,049 1,241
56-11" 55' 56' 686 745 804 863 920 979 1,038 1,097 1,216 1,434
8 IN. DIA. DRIVE PULLEY

61-11" 60' 61' 731 794 857 920 981 1,044 1,107 1,170 1298 1,532
66-11" 65' 66' 769 835 901 967 1,033 1,099 1,165 1,231 1,367 1,619
71-11" 70' 71' 814 884 954 1,024 1,094 1,164 1,234 1,304 1,449 1,717
76-11" 75' 76' 849 923 997 1,071 1,144 1,218 1,292 1,366 1,518 1,804
81-11" 80' 81' 894 972 1,050 1,128 1,205 1,283 1,361 1,439 1,600 1902
86-11" 85' 86' 929 1,011 1,093 1,175 1,255 1,337 1,419 1,501 1,669 1989
91-11" 90' 91' 974 1,060 1,146 1,232 1,316 1,402 1,488 1,574 1,751 2087
96-11" 95' 96' 1,012 1,101 1,190 1,279 1,368 1,457 1,546 1,635 1,820 2,174
101-11" 100' 101' 1,057 1,150 1,243 1,336 1,429 1,522 1,615 1,708 1,902 2,272
Note: A short belt segment laced on both ends, commonly called a “Dutchman”, is provided on conveyors 35 ft. to 70 ft. This allows for future belt stretch with a standard end take-up. An
underside take-up or center drive with take-up is recommended for conveyors over 70 ft. long.

STANDARD SPECIFICATIONS LOAD CAPACITY (LBS.)

HORIZONTAL W/ STANDARD BELT 25° INCLINE
BELT - Black Trackmate 120 EMB W/ ROUGHTOP
BELT 4" DRIVE PULLEY 8" DRIVE PULLEY BELT
BED - 4 in. deep x 12 ga. powder coated steel slider bed. Standard 5 ft. FPM HP WIDTH 11' 31' 51' 77' 101' 11' 31'
and 10 ft. long bolt-together sections with splice plates.
6"-16" 800 790 770 740 720 330 325
END DRIVE - Located on discharge end of conveyor. Chain guard is on 1/2
18"-30" 790 760 720 680 640 325 315
left-hand side when standing at infeed looking toward discharge. 35
6"-16" 825*† 1,730* 1,710* 1,690 1,660 725* 715*
1
DRIVE PULLEY - 4 in dia. with 1 in. dia. shaft at bearings or 8 in. dia. 18"-30" 825* † 1,690* 1,660* 1,620 1,580 715* 700*
with 1 7/16 in. dia. shaft at bearings. Machined, crowned and fully 6"-16" 470 450 430 405 390 195 185
lagged. 1/2
18"-30" 450 420 390 340 300 185 175
TAIL PULLEY - 4 in. dia. with 1 in. dia. shaft at bearings. Machined 6"-16" 825 † 1,030 1,010 980 960 435 425
65 1
crown. 18"-30" 825 † 1000 960 920 880 425 415
6"-16" 825* † 2,090* 2,070* 2,050 2,030 875* 870*
SNUB ROLLERS - Adjustable 2 1/2 in. dia. rollers. Grease packed ball 2
18"-30" 825* † 2060* 2030* 1,980 1,950 865* 855*
bearings. Includes guard.
6"-16" 325 310 290 265 240 135 125
RETURN ROLLERS - Adjustable 1.9 in. dia. rollers. Grease packed ball 1/2
18"-30" 310 275 245 195 160 130 115
bearings 6"-16" 720 705 690 660 640 300 290
100 1
TAKE-UP - Provides 4 in. of belt take-up at tail pulley 18"-30" 710 675 640 595 555 295 280
6"-16" 825 † 1,430 1415 1,390 1,365 600 595
BEARINGS - Sealed, pre-lubricated, self-aligning, ball bearings on drive 2
18"-30" 825 † 1400 1,370 1,320 1,280 595 580
and tail pulleys
6"-16" 250 235 215 190 170 105 95
BELT SPEED - Constant 65 FPM 1/2
18"-30" 235 200 170 120 85 95 85
SPEED REDUCTION - Sealed worm gear C-face speed reducer with 135 1
6"-16" 535 520 500 475 455 225 215
No. 50 roller chain to drive pulley 18"-30" 520 485 455 405 370 215 205
6"-16" 825 † 1,100 1,085 1,055 1,035 465 455
MOTOR - 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan 2
18"-30" 825 † 1,070 1035 990 950 455 445
cooled, energy efficient
* Requires 8" diameter drive pulley in lieu of 4" diameter. †Limited by conveyor capacity
FRAME CAPACITY - Maximum load per linear foot of conveyor is 75
lbs. Not to exceed drive capacity in chart.
1
4" END DRIVE

OVERALL LENGTH

6" BED LENGTH 6"

4" DIA. DRIVE PULLEY X 4" DIA. TAIL PULLEY
FLOW
NIP POINT GUARD NIP POINT GUARD
2-1/2" DIA. SNUB ROLLER 1.9" DIA. RETURN ROLLER TAKE UP

4-3/4"
15-1/2"
MAX. 2-1/2" DIA.
SNUB ROLLER

12" APPROX.
22-3/4" 11-1/4" MAX.
X
34" MAX.

OPTIONAL SMS SUPPORT SHOWN

SECTION VIEW X-X 8" END DRIVE 4" SHAFT MOUNTED DRIVE
2-1/2" DIA.
FORMED OVERALL LENGTH
3-3/4" BED WIDTH SNUB ROLLER
STEEL BED 17" BED LENGTH
8" DIA.
BELT WIDTH DRIVE PULLEY FLOW

4" 9-1/2"

19" MAX.

12" APPROX.
2-1/8" DIA. 24-3/4" 11-1/4" MAX.
SNUB ROLLER
36" MAX.

OPTIONAL SMSD SUPPORT SHOWN

TOTALLY ENCLOSED CHAIN GUARD

OPTIONAL EQUIPMENT
LENGTH / WIDTH - Other in-between widths are lengths are SHAFT MOUNTED END DRIVE - 4 in. dia. drive pulley only. Drive
available unit mounted on extended pulley shaft. Mounting bracket and torque
arm enable multiple mounting positions. 4 7/8 in. minimum elevation.
FLOOR SUPPORTS - SMS floor supports are available in wide range
of adjustments. Specify top of belt elevation. One support is required OTHER DRIVE VARIATIONS - Side mounted end or center drives
at every bed joint and at ends of conveyor. Holes in feet are provided
for lagging to floor. Knee braces supplied on SMS-7 support and UNDERSIDE TAKE-UP - Provides 16 in. of belt take-up. Extends
above. down 13 1/8 in. from top of belt.

BELT - Tan Glidetop, White Polymate 100 RMP – COS, Black V-GUIDED CONSTRUCTION - When overall length to belt width ratio
Trackmate 120 Roughtop with PVC cover drops below 2.5:1 but is still greater than 1:1, V-guided belt is required
to maintain belt tracking
BELT SPEED - Other constant and variable speeds
• 4 in. dia. drive pulley: 35, 40, 50, 80, 100 and 135 FPM GRAVITY BRACKETS - Brackets and support bar allows skatewheel
• 8 in. dia. drive pulley: 17 – 135 FPM in any increment or 1 3/8 in. dia. gravity roller conveyor to be supported at end of belt
• Contact factory for speeds not listed above conveyor. Includes 1 in. dia. pop-out transfer roller.

OTHER PULLEY OPTIONS BUTT COUPLINGS - Brackets allow 1.9 in / 2 in. dia. gravity roller
• 8 in. dia. drive pulley with 1 7/16 in. dia. shaft at bearings in lieu conveyor along with other conveyors to be attached to end of belt
of 4 in. dia. drive pulley conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or
• 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in lieu underside take-up recommended if butt couplings are to be located at
of 4 in. dia. tail pulley tail end.
• 1 1/8 in. dia. nose roller assembly in lieu of 4 in. dia. tail pulley. GUIDE RAILS - Adjustable channel guide rails, solid side guides
Center drive is required.
OTHER ACCESSORIES - Floor supports with casters, poly-tier
MOTORS - Inverter duty, premium energy efficient, single phase, supports, ceiling hangers. See accessory section.
brake motor, other characteristics. 2 HP maximum.
ELECTRICAL CONTROLS - One direction manual start switch,
CENTER DRIVE / TAKE-UP - Provides 16 in. of belt take-up and is reversing drum switch, non-reversing and reversible IEC starters, push
suitable for reversing applications button stations, AC variable frequency drive
• Standard underhung drive (4 in. dia. drive pulley): 16 in.
minimum elevation. 78 in. minimum OAL.
• Standard underhung drive (8 in. dia. drive pulley): 17 in.
minimum elevation. 78 in. minimum OAL.
• Side mount drive/low elevation center drive (4 in. or 8 in. dia.
drive pulley): 13 1/2 in. minimum elevation. 66 in. minimum
OAL.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

2
BS300B
HORIZONTAL BELT CONVEYOR
(Slider Bed)
With its rugged, heavier duty construction, the BS300B is
ideal for transporting larger packages or multiple smaller
packages across its width. It can be used in many types of
material handling applications such as assembly operations,
sorting, packaging, and inspection or for simply transporting
product from point A to B.
n Smooth, slim design
n Coped ends
n 6 belt widths
n Multiple belt options

CONVEYOR WEIGHTS (LBS.)

BELT WIDTH
OVERALL LENGTH OVERALL LENGTH 24" 30" 36" 42" 48" 52"
6" DIA. TAIL BED LENGTH WITH CENTER
PULLEY DRIVE BED WIDTH
30" 36" 42" 48" 54" 58"

7'-1" 5' 6'-4" 461 445 N/A N/A N/A N/A

12'-1" 10' 11'-4" 564 629 698 767 834 880
17'-1" 15' 16'-4" 672 751 837 922 1,003 1,061
22'-1" 20' 21'-4" 775 868 969 1,069 1,166 1,234
27'-1" 25' 26'-4" 883 991 1,108 1,224 1,335 1,415
32'-1" 30' 31'-4" 986 1,108 1,240 1,372 1,498 1,588
37'-1" 35' 36'-4" 1,094 1,230 1,379 1,527 1,667 1,769
42'-1" 40' 41'-4" 1,197 1,347 1,511 1,674 1,830 1,942
47'-1" 45' 46'-4" 1,302 1470 1,650 1,829 1,999 2,123
52'-1" 50' 51'-4" 1,408 1,587 1,782 1,977 2,162 2,296
57'-1" 55' 56'-4" 1,516 1,709 1,921 2,132 2,331 2,477
62'-1" 60' 61'-4" 1,619 1,826 2,053 2,279 2,494 2,650
67'-1" 65' 66'-4" 1,727 1,949 2,192 2,434 2,663 2,831
72'-1" 70' 71'-4" 1,830 2,066 2,324 2,582 2826 3,004
77'-1" 75' 76'-4" 1,938 2,188 2,463 2,737 2,995 3,185
82'-1" 80' 81'-4" 2,041 2,305 2,595 2,884 3,158 3,358
87'-1" 85' 86'-4" 2,149 2,428 2,734 3,089 3,327 3,539
92'-1" 90' 91'-4" 2,252 2,545 2,866 3,187 3,490 3,712
97'-1" 95' 96-4" 2,360 2,667 3,005 3,342 3,659 3,893
102'-1" 100' 101'-4" 2,463 2,784 3,137 3,489 3,822 4,066
Note: A short belt segment laced on both ends, commonly called a “Dutchman”, is provided on conveyors 35 ft. to 70 ft. This allows for future belt stretch with standard end take-up. An
underside take-up or center drive with take-up is recommended for conveyors over 70 ft. long.

STANDARD SPECIFICATIONS
BELT - Black Trackmate 120 EMB LOAD CAPACITY (LBS.)
BED - 6 5/8 in. deep x 12 ga. powder coated steel slider bed. Standard HORIZONTAL W/ STANDARD BELT
5 ft. and 10 ft. long bolt-together sections with splice plates. 8" DRIVE PULLEY
BELT
END DRIVE - Located on discharge end of conveyor. Chain guard is on FPM HP WIDTH 12' 32' 52' 78' 102'
left-hand side when standing at infeed looking toward discharge.
24"-30" 1,200* 1,690 1,660 1,620 1,580
DRIVE PULLEY - 8 in. dia. with 1 7/16 in. dia. shaft at bearing.
35 1 36"-42" 1,200* 1,660 1,620 1,560 1,510
Machined, crowned and fully lagged.
48"-52" 1,200* 1,640 1,580 1,510 1,450
TAIL PULLEY - 6 in. dia. with 1 3/16 in. dia. shaft at bearing. Machined 24"-30" 1,020 980 960 910 870
crown 1 36"-42" 1,000 960 920 860 800
SNUB ROLLERS - Adjustable 2 1/2 in. dia. rollers. Grease packed ball 65
48"-52" 990 930 880 810 740
bearings. Includes guard. 24"-30" 1,200* 2,050 2,020 1,980 1,940
2 36"-42" 1,200* 2,020 1,980 1,920 1,870
RETURN ROLLERS - Adjustable 1.9 in. dia. rollers. Grease packed ball
bearings 48"-52" 1,200* 1,990 1,940 1,870 1,800
24"-30" 690 660 630 590 550
TAKE-UP - Provides 4 in. of belt take-up at tail pulley 1 36"-42" 670 630 585 530 475
BEARINGS - Sealed, pre-lubricated, self-aligning, ball bearings on drive 100
48"-52" 660 605 550 480 410
and tail pulleys 24"-30" 1,200* 1,390 1,355 1,315 1,280
2 36"-42" 1,200* 1,360 1,310 1,255 1,200
BELT SPEED - Constant 65 FPM
48"-52" 1,200* 1,330 1,275 1,205 1,140
SPEED REDUCTION - Sealed worm gear C-face speed reducer with 24"-30" 505 475 445 400 365
No. 50 roller chain to drive pulley 1 36"-42" 485 440 400 340 290
MOTOR - 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan 135
48"-52" 470 415 360 290 225
cooled, energy efficient 24"-30" 1,090 1,055 1,025 985 945
2 36"-42" 1,070 1,025 980 925 870
FRAME CAPACITY - Maximum load per linear foot of conveyor is 100
lbs. Not to exceed drive capacity in chart. 48"-52" 1,055 1,000 945 875 810
* Limited by conveyor capacity
3
8" END DRIVE

OVERALL LENGTH

17" BED LENGTH 8"

8" DIA. DRIVE PULLEY X 6" DIA. TAIL PULLEY
FLOW
NIP POINT GUARD
2-1/2" DIA. SNUB ROLLER 1.9" DIA. RETURN ROLLER TAKE-UP

9-1/2"

19" MAX. 2-1/2" DIA.

SNUB ROLLER

12" APPROX.

24" 12" MAX. X

36" MAX.

OPTIONAL SMSD SUPPORT SHOWN OPTIONAL SMS SUPPORT SHOWN

SECTION VIEW X-X

FORMED STEEL BED
4" BED WIDTH

BELT WIDTH

6-5/8"

1.9" DIA. RETURN ROLLER

SPREADER

TOTALLY ENCLOSED CHAIN GUARD

OPTIONAL EQUIPMENT
FLOOR SUPPORTS - SMS floor supports are available in wide range UNDERSIDE TAKE-UP - Provides 16 in. of belt take-up. Extends
of adjustments. Specify top of belt elevation. One support is required down 15 3/4 in. from top of belt.
at every bed joint and at ends of conveyor. Holes in feet are provided
V-GUIDED CONSTRUCTION - When overall length to belt width ratio
for lagging to floor. Knee braces supplied on SMS-7 support and
drops below 2.5:1 but is still greater than 1:1, V-guided belt is required
above.
to maintain belt tracking.
BELT - Tan Glidetop, White Polymate 100 RMP - COS, Black
BUTT COUPLINGS - Brackets allow 1.9 in / 2 in. dia. gravity roller
Trackmate 120 Roughtop with PVC cover
conveyor along with other conveyors to be attached to end of belt
BELT SPEED - Other constant and variable speeds: 17 - 135 FPM in conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or
any increment. Contact factory for speeds not listed. underside take-up recommended if butt couplings are to be located at
tail end.
MOTORS - Inverter duty, premium energy efficient, single phase,
brake motor, other characteristics. 2 HP maximum. GUIDE RAILS - Adjustable channel guide rails, solid side guides
CENTER DRIVE / TAKE-UP - Provides 16 in. of belt take-up and is OTHER ACCESSORIES - Floor supports with casters, poly-tier
suitable for reversing applications supports, ceiling hangers. See accessory section.
• Standard underhung drive: 20 in. minimum elevation. 78 in.
ELECTRICAL CONTROLS - One direction manual start switch,
minimum OAL.
reversing drum switch, non-reversing and reversible IEC starters, push
• Side mount drive/low elevation center drive: 16 1/2 in.
button stations, AC variable frequency drive
minimum elevation. 66 in. minimum OAL.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

4
BS100C
HORIZONTAL BELT CONVEYOR
(Slider Bed)
The BS100C belt conveyor is designed with channel
frames and bolt-in pans making it ideal for matching up
with other roller bed conveyors. It can be used in many
types of material handling applications such as assembly
operations, sorting, packaging, and inspection or for
simply transporting product from point A to B.
n 15 belt widths
n Center drive and take-up
n Readily bolts up to other roller bed conveyors
n Multiple belt options

CONVEYOR WEIGHTS (LBS.)

BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36" 42" 48" 54"
BETWEEN FRAME WIDTH
OVERALL BED
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" 45" 51" 57"
LENGTH LENGTH
OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 48" 54" 60"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS

12' 10' 513 555 595 636 677 717 758 860 933 984 1,050 1,098 1,231 1,360 1,498
17' 15' 595 643 690 736 783 829 877 986 1,070 1,127 1,198 1,253 1,409 1,556 1,711
22' 20' 674 727 780 832 884 937 991 1,106 1,202 1,265 1,342 1,403 1,582 1,747 1,919
27' 25' 753 812 870 928 986 1,044 1,103 1,225 1,331 1,400 1,483 1,549 1,750 1,931 2,120
32' 30' 831 896 960 1,023 1,087 1,151 1,217 1,345 1,463 1,538 1,627 1,699 1,923 2,122 2,328
37' 35' 911 982 1,050 1,119 1,189 1,258 1,330 1,463 1,592 1,673 1,767 1,844 2,091 2,306 2,529
42' 40' 989 1,065 1,140 1,215 1,290 1,366 1,444 1,584 1,724 1,811 1,911 1,994 2,264 2,497 2,737
47' 45' 1,068 1,151 1,230 1,311 1,392 1,473 1,556 1,702 1,854 1,945 2,051 2,140 2,431 2,681 2,938
52' 50' 1,146 1,235 1,320 1,406 1,494 1,580 1,670 1,822 1,985 2,083 2,195 2,290 2,605 2,872 3,146
57' 55' 1,226 1,320 1,411 1,503 1,595 1,687 1,783 1,940 2,115 2,218 2,335 2,436 2,773 3,056 3,347
62' 60' 1,304 1,403 1,500 1,598 1,697 1,795 1,897 2,061 2,247 2,356 2,480 2,586 2,945 3,247 3,555
67' 65' 1,383 1,489 1,592 1,694 1,798 1,902 2,010 2,179 2,376 2,491 2,620 2,732 3,113 3,431 3,756
72' 70' 1,461 1,573 1,681 1,790 1,900 2009 2,124 2,300 2,508 2,629 2,764 2,882 3,286 3,622 3,964
77' 75' 1,541 1,658 1,772 1,886 2,001 2,116 2,237 2,418 2,637 2,764 2,904 3,028 3,454 3,806 4,165
82' 80' 1,619 1,742 1,862 1,981 2,103 2,224 2,351 2,539 2,769 2,902 3,048 3,178 3,627 3,997 4,373
87' 85' 1,698 1,827 1,952 2,077 2,205 2,331 2,463 2,657 2,898 3,037 3,188 3,323 3,795 4,181 4,574
92' 90' 1,776 1,911 2,042 2,173 2,306 2,438 2,577 2,777 3,030 3,175 3,332 3,473 3,968 4,372 4,782
97' 95' 1,855 1,996 2,133 2,269 2,408 2,545 2,690 2,895 3,160 3,309 3,473 3,619 4,136 4,556 4,983
102' 100' 1,934 2,080 2,222 2,365 2,509 2,653 2,804 3,016 3,292 3,447 3,617 3,769 4,309 4,747 5,191

STANDARD SPECIFICATIONS
BELT – Black Trackmate 120 EMB LOAD CAPACITY (LBS.)

BED – 6 1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel HORIZONTAL W/ STANDARD BELT
channel frame with bolt-in slider pans and cross members. Standard 5 BELT 8" DRIVE PULLEY
ft. and 10 ft. long bolt-together sections with splice plates. FPM HP WIDTH 12' 32' 52' 77' 102'
CENTER DRIVE – Can be placed on any section of conveyor length. 10"-18" 1,200* 1,720 1,710 1,680 1,660
Minimum elevation is 17 7/8 in. Minimum OAL is 90". Chain guard 35 1 20"-30" 1,200* 1,700 1,680 1,640 1,600
is located on left-hand side when standing at infeed looking toward 34"-54" 1,200* 1,660 1,610 1,540 1,480
discharge.
10"-18" 1,045 1,030 1,010 990 970
DRIVE PULLEY – 8 in dia. with 1 7/16 in. dia. shaft at bearing. 1 20"-30" 1,030 1,000 970 940 900
Machined, crowned and fully lagged. 34"-54" 1,000 950 900 840 780
65
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 10"-18" 1,200* 2,095 2,080 2,050 2,030
1 3/16 in. dia. shaft at bearing. Machined crown. 2 20"-30" 1,200* 2,070 2,040 2,000 1,970
34"-54" 1,200* 2,020 1,970 1,900 1,840
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball
10"-18" 720 700 685 660 640
bearings. Includes guard.
1 20"-30" 705 680 650 610 580
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 34"-54" 680 630 580 510 450
bearings 100
10"-18" 1,200* 1,430 1,410 1,390 1,370
TAKE-UP – Located in center drive. Provides 16 in. of belt take-up. 2 20"-30" 1,200* 1,405 1,380 1,340 1,310
34"-54" 1,200* 1,355 1,305 1,240 1,180
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive
10"-18" 530 515 500 475 455
and tail pulleys
1 20"-30" 520 490 465 425 395
BELT SPEED – Constant 65 FPM 34"-54" 490 440 390 325 265
135
SPEED REDUCTION - Sealed worm gear C-face speed reducer with 10"-18" 1,115 1,100 1,080 1,060 1,040
No. 50 roller chain to drive pulley 2 20"-30" 1,100 1,075 1,045 1,010 975
34"-54" 1,075 1,025 975 910 850
MOTOR – 1 HP –230/460V – 3 phase – 60 Hz totally enclosed fan
cooled, energy effcient * Limited by conveyor capacity

FRAME CAPACITY – Maximum load per linear foot of conveyor is 100

lbs. Not to exceed drive capacity in chart.
5
8" CENTER DRIVE

SECTION VIEW X-X

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range PULLEYS – 6 in. dia. tail with 1 3/16 in. dia. shaft at bearing in place
of adjustments. Specify top of belt elevation. One support is required of 4 in. when not furnished as standard
at every bed joint and at ends of conveyor. Holes in feet are provided
V-GUIDED CONSTRUCTION – When overall length to belt width
for lagging to floor. Knee braces supplied on SMS-7 support and
ratio drops below 2.5:1 but is still greater than 1:1, V-guided belt is
above.
required to maintain belt tracking.
BELT – Tan Glidetop, White Polymate 100 RMP – COS, Black
SLAVE KIT – To slave VBC19 curve from system end of belt conveyor
Trackmate 120 Roughtop with PVC cover
GUIDE RAILS – Adjustable channel guide rails, fixed angle and
BELT SPEED – Other constant and variable speeds: 17 – 135 FPM in
channel guide rails
any increment. Contact factory for other speeds.
OTHER ACCESSORIES – Floor supports with casters, poly-tier
MOTORS – Inverter duty, premium energy efficient, single phase,
supports, ceiling hangers. See accessory section.
brake motor, other characteristics. 2 HP maximum.
ELECTRICAL CONTROLS – One direction manual start switch,
SIDE MOUNT CENTER DRIVE / TAKE-UP – Provides 16 in. of belt
reversing drum switch, non-reversing and reversible IEC starters, push
take-up. 16 1/2 in. minimum elevation. 78 in. minimum OAL.
button stations, AC variable frequency drive.
END DRIVE – Requires underside take-up
• 8 in. underhung end drive: 16 in. minimum elevation. 104 in.
minimum OAL.
• 8 in. side mount end drive: 13 in. minimum elevation. 96 in.
minimum OAL.
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends
down 15 7/8 in. from top of belt.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

6
BR100C
HORIZONTAL BELT CONVEYOR
(Roller Bed)
The BR100C belt conveyor is ideal for moving heavier loads.
The roller bed design reduces belt friction which increase it’s
load capacity. It can be used in many types of material handling
applications such as assembly operations, packaging, and
inspection or for simply transporting product from point A to B.
n 15 belt widths
n Center drive and take-up
n Ideal for heavier loads
n Readily bolts up to other roller bed conveyors

CONVEYOR WEIGHTS (LBS.)

BELT WIDTH
10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36" 42" 48" 54"
BETWEEN FRAME WIDTH
OVERALL BED
13" 15" 17" 19" 21" 23" 25" 27" 31" 33" 37" 39" 45" 51" 57"
LENGTH LENGTH
OVERALL FRAME WIDTH
16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42" 48" 54" 60"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS

12' 10' 518 562 600 638 682 725 778 832 891 935 1005 1048 1,160 1,274 1390
17' 15' 602 654 697 740 791 841 907 973 1,042 1,094 1,172 1,223 1,351 1,481 1,615
22' 20' 683 742 789 837 895 953 1,032 1,110 1,188 1,247 1,335 1,393 1,538 1,684 1,834
27' 25' 765 831 882 934 999 1,064 1,154 1,245 1,331 1,397 1,494 1559 1,719 1,881 2,046
32' 30' 845 918 975 1,031 1,103 1,175 1,279 1,382 1,477 1,551 1,657 1,729 1,905 2,084 2,266
37' 35' 927 1,007 1,068 1,128 1,207 1,286 1,402 1,517 1,621 1,701 1,815 1,894 2,086 2,280 2,478
42' 40' 1,007 1,095 1,160 1,225 1,311 1,398 1,526 1,654 1,767 1,855 1,978 2,064 2,273 2,484 2,697
47' 45' 1,089 1,183 1,253 1,323 1,416 1,509 1,649 1,789 1,910 2,005 2,137 2,230 2,454 2,681 2,910
52' 50' 1,169 1,271 1,345 1,419 1,520 1,620 1,773 1,926 2,057 2,158 2,300 2,400 2,641 2,884 3,129
57' 55' 1,251 1,360 1,438 1,517 1,624 1,731 1,896 2,061 2,200 2,309 2,459 2,566 2,822 3,080 3,341
62' 60' 1,332 1,447 1,530 1,614 1,728 1,842 2,020 2,197 2,346 2,462 2,621 2,736 3,009 3,283 3,561
67' 65' 1,413 1,536 1,624 1,711 1,832 1,954 2,143 2,332 2,490 2,612 2,780 2,902 3,190 3,480 3,773
72' 70' 1,494 1,624 1,716 1,808 1,936 2,065 2,267 2,469 2,636 2,766 2,943 3,072 3,376 3,683 3,993
77' 75' 1,576 1,712 1,809 1,905 2,041 2,176 2,390 2,604 2,779 2,916 3,102 3,238 3,558 3,880 4,205
82' 80' 1,656 1,800 1,901 2,002 2,144 2,288 2,514 2,741 2,925 3,070 3,265 3,408 3,744 4,082 4,424
87' 85' 1,738 1,889 1,994 2,099 2,248 2,399 2,637 2,876 3,059 3,220 3,424 3,573 3,925 4,279 4,636
92' 90' 1,818 1,976 2,086 2,196 2,353 2,510 2,762 3,013 3,215 3,373 3,586 3,743 4,112 4,483 4,856
97' 95' 1,900 2,065 2,179 2,294 2,457 2,621 2,885 3,148 3,359 3,524 3,745 3,909 4,293 4,979 5,068
102' 100' 1,980 2,153 2,272 2,390 2,561 2,732 3,008 3,285 3,505 3,677 3,908 4,079 4,480 4,882 5,288

STANDARD SPECIFICATIONS LOAD CAPACITY (LBS)

HORIZONTAL W/ STANDARD BELT
BELT – Black Trackmate 120 EMB BELT 8" DRIVE PULLEY
BED – 6-1/2 in. deep x 1 1/2 in. flange x 12 ga. powder coated steel FPM HP WIDTH 12' 32' 52' 77' 102'
channel frame with 1.9 dia. roller x 16 ga. tube spaced every 6 in. 10"-18" 2,700* 4,600 4,400 4,200 4,000
Standard 5 ft. and 10 ft. bolt-together sections with splice plates. 1/2 20"-30" 2,700* 4,400 4,100 3,800 3,500
CROSS BRACING – Rods with turnbuckles are fastened to underside of 34"-54" 2,700* 4,000 3,600 3,000 2,400
35
bed to provide squaring adjustment and insure correct product tracking. 10"-18" 2,700* 7,200* 10,100 9,900 9,600
Supplied on every other section, 30 ft. bed lengths and over. 1 20"-30" 2,700* 7,200* 9,800 9,500 9,100
34"-54" 2,700* 7,200* 9,200 8,700 8,100
CENTER DRIVE – Can be placed on any section of conveyor length. 10"-18" 2,700* 2,600 2,400 2,200 2,000
Minimum elevation – 17 7/8 in. Minimum OAL is 90". Chain guard is on 1/2 20"-30" 2,650 2,400 2,100 1,800 1,450
left-hand side when standing at infeed looking toward discharge. 34"-54" 2,500 2,000 1,600 1,000 450
10"-18" 2,700* 6,050 5,900 5,650 5,450
DRIVE PULLEY – 8 in dia. with 1 7/16 in. dia. shaft at bearing. 65 1 20"-30" 2,700* 5,900 5,600 5,250 4,950
Machined, crowned and fully lagged. 34"-54" 2,700* 5,500 5,050 4,450 3,900
10"-18" 2,700* 7,200* 12,,300 12,050 11,850
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with
2 20"-30" 2,700* 7,200* 12000 11,650 11,350
1 3/16 in. dia. shaft at bearing. Machined crown 34"-54" 2,700* 7,200* 11,450 10,850 10,300
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball 10"-18" 1,900 1,750 1,550 1,350 1,150
bearings. Includes guard. 1/2 20"-30" 1,800 1,550 1,300 950 600
34"-54" 1,650 1,200 750 150 NA
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 10"-18" 2,700* 4,100 3,950 3,700 3,500
bearings 100 1 20"-30" 2,700* 3,950 3,650 3,300 3,000
34"-54" 2,700* 3,550 3,100 2,500 1,950
TAKE-UP – Provides 16 in. of belt take-up in center drive 10"-18" 2,700* 7,200* 8,300 8,050 7,850
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive 2 20"-30" 2,700* 7,200* 8,050 7,650 7,350
and tail pulleys. 34"-54" 2,700* 7,200* 7,450 6,850 6,350
10"-18" 1,450 1,300 1,100 900 650
BELT SPEED – Constant 65 FPM 1/2 20"-30" 1,350 1,100 850 500 150
SPEED REDUCTION - Sealed worm gear C-face speed reducer with 34"-54" 1,200 750 300 NA NA
10"-18" 2,700* 3,000 2,850 2,600 2,400
No. 50 roller chain to drive pulley
135 1 20"-30" 2,700* 2,800 2,550 2,200 1,900
MOTOR – 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan 34"-54" 2,700* 2,450 2,000 1,400 850
cooled, energy efficient 10"-18" 2,700* 6,500 6,300 6,100 5,900
2 20"-30" 2,700* 6,300 6,000 5,700 5,350
FRAME CAPACITY – Maximum load per linear foot of conveyor is 225 34"-54" 2,700* 5,950 5,500 4,900 4,350
lbs. Not to exceed drive capacity in chart. * Limited by conveyor capacity
7
8" CENTER DRIVE
OVERALL LENGTH
12" BED LENGTH 12"

1.9" DIA. POP-OUT ROLLER 6" DIA. TAKE-UP PULLEY

TAKE-UP
4" OR 6" DIA. TAIL PULLEY 8" DIA. DRIVE PULLEY
2-1/2" DIA. SNUB ROLLER PREFERRED
FLOW 1.9" DIA. TREAD ROLLER
X
1.9" DIA. RETURN IDLER

17-7/8" 8" 8"

10 7/8"

21" 26-1/2"

12" APPROX.

63" MAX.

X
OPTIONAL SMS SUPPORT SHOWN
2-1/2" DIA. SNUB IDLER

SECTION VIEW X - X

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range ROLLER CENTERS – Bed rollers spaced on 3 in., 9 in., or 12 in.
of adjustments. Specify top of belt elevation. One support is required centers.
at every bed joint and at ends of conveyor. Holes in feet are provided
PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place
for lagging to floor. Knee braces supplied on SMS-7 support and
of 4 in. when not furnished as standard.
above.
SLAVE KIT – To slave VBC19 curve from system end of belt conveyor.
BELT – Tan Glidetop, White Polymate 100 RMP – COS, Black
Trackmate 533 COS-PVC GUIDE RAILS – Adjustable channel guide rails, fixed angle and
channel guide rails.
BELT SPEED – Other constant and variable speeds: 17 – 135 FPM in
any increment. Contact factory for speeds not listed above. OTHER ACCESSORIES – Floor supports with casters, poly-tier
supports, ceiling hangers. See accessory section.
MOTORS – Inverter duty, premium energy efficient, single phase,
brake motor, other characteristics. 2 HP maximum. ELECTRICAL CONTROLS – One direction manual start switch,
reversing drum switch, non-reversing and reversible IEC starters, push
SIDE MOUNT CENTER DRIVE / TAKE-UP – Provides 16 in. of belt
button stations, AC variable frequency drive.
take-up. 16 1/2 in. minimum elevation. 60 in. minimum OAL
END DRIVE – Requires underside take-up
• 8 in. underhung end drive: 16 in. minimum elevation. 104 in.
minimum OAL.
• 8 in. side mount end drive: 13 in. minimum elevation. 96 in.
minimum OAL.
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends
down 15 7/8 in. from top of belt.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

8
BSC
BELT CURVE
The BSC belt curve is ideal for transporting products of
various sizes and shapes. It helps maintain proper product
orientation and positive traction through the curve.
n 8 conveying widths
n Quiet and low maintenance belt guiding system
n 45, 90, and 180 degree curves

CR F J GAP (APPROX.) MAX. WEIGHT (LBS.)

OR IR H PULLEY DISTRIB.
OUTSIDE CONVEYING CENTER BOTTOM
INSIDE FRAME SHAFT LIVE LOAD
WIDTH LINE OF FRAME MIN. MAX. NORM. 45° 90° 180
RADIUS RADIUS HEIGHT SIZE
RADIUS TO TOB (LBS)

12" 36" 42" 3 5/8" 5 1/8" 4" 169 337 674

18" 30" 39" 3 1/4" 4 3/4" 3 5/8" 187 374 748
48" 9 1/16" 10 15/16" 1" 400
20" 28" 38" 3 1/4" 4 5/8" 3 5/8" 191 381 762
24" 24" 36" 3" 4 3/8" 3 3/8" 200 399 798
24" 36" 48" 4 1/8" 5 7/8" 4 9/16" 261 521 1,042
60" 30" 30" 45" 10 9/16" 12 3/8" 3 7/8" 5 7/8" 4 3/8" 1 3/16" 600 278 556 1,112
36" 24" 42" 3 5/8" 5 1/8" 4" 294 587 1,174
36" 36" 54" 4 1/4" 6 5/8" 4 7/8" 379 757 1,514
72" 42" 30" 51" 12" 13 7/8" 4" 6 1/4" 4 5/8" 1 7/16" 700 398 795 1,590
48" 24" 48" 3 3/4" 5 7/8" 4 1/4" 414 828 1,656

STANDARD SPECIFICATIONS
BELT - Black Trackmate 120 EMB
BED - 10 ga. steel frame and slider bed pan. Welded construction.
CURVES - 45, 90 and 180 degree curves. Radius is dependent upon
conveying width (see chart).
DRIVE AND TAIL PULLEYS - Tapered pulley with ruff-top lagging
BEARINGS - Sealed, pre-lubricated, self-aligning ball bearings on
drive and tail pulleys.
BELT GUIDING SYSTEM - Belt is mechanically guided at outside rail
with wheel. These wheels provide quiet operation, minimal friction and
require virtually no maintenance.
BELT SPEED - Constant 65 FPM at belt centerline
SPEED REDUCTION - Sealed worm gear shaft mounted speed
reducer
MOTOR – 3/4 HP - 230/460 V - 3 phase - 60 Hz. - totally enclosed fan
cooled, energy efficient
CAPACITY – See chart

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – H-style floor supports are available with +/- 2
in. adjustment. Specify top of belt elevation. One support is required
at each end along with one single support at the center. Holes in feet
are provided for lagging to floor.
BELT – PVC-120 white, Trackmate 120 RT-B Roughtop, food grade
and other belts available
BELT SPEED – Other constant and variable speeds up to 300 FPM.
Note: Capacity is affected with speed range.
OTHER ACCESSORIES – Guide rails, ceiling hangers
ELECTRICAL CONTROLS – Non-reversing and reversible IEC LOAD CAPACITY
starters and push button stations, AC variable frequency drive OR DEGREE
FPM HP OUTSIDE CONVEYING
WIDTH 45° 90° 180°
RADIUS
48" 12"-24" 380 360 310
3/4 60" 24"-36" 310 280 190
72" 36"-48" 200 190 150
48" 12"-24" 400* 400* 400*
65 1 60" 24"-36" 540 510 430
72" 36"-48" 430 390 270
48" 12"-24" 400* 400* 400*
2 60" 24"-36" 600* 600* 600*
72" 36"-48" 700* 700* 700*
* Maximum distributed live load for curve
Contact factory for drive capacity at other speeds

9
BSI
INCLINE BELT CONVEYOR
(Slider Bed)
The BSI belt conveyor is ideal for transporting product
from floor-to-floor or as a booster conveyor in gravity flow
systems. It includes an adjustable double nose-over to
ensure smooth transfer from incline to horizontal that can be
easily adjusted up to 30 degrees. The frame design makes
it ideal for matching up with other roller bed conveyors.
n 12 belt widths
n Double nose-over
n Readily bolts up to other roller bed conveyors in a system

CONVEYOR WEIGHTS (LBS.)

DIMENSIONS @ 25° WITH 4" BELT WIDTH BELT WIDTH
DIA. TAIL PULLEY * 10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36"
OVERALL BETWEEN FRAME WIDTH OVERALL BETWEEN FRAME WIDTH
BED LENGTH LENGTH
HORIZONTAL (REF.) 13" 15" 17" 19" 21" 23" 25" (REF.) 27" 31" 33" 37" 39"
LENGTH VERTICAL
DISTANCE
LIFT OVERALL FRAME WIDTH OVERALL FRAME WIDTH
ALONG FLOOR
"VL" 16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
"HF"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS

10' 4' - 7" 12' - 10" 13'-10" 665 719 787 840 894 946 999 14' 1,311 1,456 1,534 1,676 1,752
12' 5' - 5" 14' - 7" 15'-10" 692 749 820 876 932 988 1,043 16' 1,358 1,508 1,588 1,733 1,812
14' 6' - 3" 16' - 5" 17'-10" 720 779 853 911 971 1,029 1,088 18' 1,405 1,559 1,642 1,789 1,871
16' 7' - 1" 18' - 3" 19'-10" 755 816 891 951 1,011 1,071 1,132 20' 1,451 1,609 1,694 1,843 1,926
18' 8' - 0" 20' - 1" 21'-10" 783 846 924 986 1,050 1,112 1,176 22' 1,498 1,661 1,748 1,899 1,985
20' 8' - 10" 21' - 10" 23'-10" 813 878 957 1,021 1,086 1,150 1,215 24' 1,540 1,706 1,795 1,948 2,035
22' 9' - 8" 23' - 8" 25'-10" 841 909 990 1,057 1,125 1,191 1,259 26' 1,586 1,758 1,849 2,005 2,095
24' 10' - 6" 25' - 6" 27'-10" 868 939 1,023 1,093 1,163 1,232 1,304 28' 1,633 1,809 1,903 2,061 2,154
26' 11' - 4" 27' - 4" 29'-10" 900 972 1,058 1,128 1,199 1,270 1,342 30' 1,672 1,852 1,947 2,106 2,200
28' 12' - 2" 29' - 1" 31'-10" 928 1,003 1,091 1,164 1,238 1,311 1,386 32' 1,719 1,903 2,001 2,163 2,259
30' 13' - 0" 30' - 11" 33'-10" 958 1,035 1,124 1,198 1,274 1,348 1,425 34' 1,761 1,949 2,048 2,211 2,309
32' 13' - 11" 32' - 9" 35'-10" 986 1,065 1,157 1,234 1,313 1,390 1,469 36' 1,808 2,000 2,102 2,268 2,369
34' 14' - 9" 34' - 7" 37'-10" 1,014 1,095 1,190 1,270 1,351 1,431 1,514 38' 1,855 2,051 2,156 2,324 2,428
36' 15' - 7" 36' - 4" 39'-10" 1,046 1,128 1,224 1,305 1,387 1,468 1,552 40' 1,894 2,094 2,200 2,369 2,474
38' 16' - 5" 38' - 2" 41'-10" 1,073 1,159 1,257 1,341 1,426 1,510 1,596 42' 1,941 2,145 2,254 2,426 2,533
40' 17' - 3" 40' - 0" 43'-10" 1,104 1,191 1,290 1,375 1,462 1,547 1,635 44' 1,982 2,191 2,301 2,475 2,583

* See incline dimensional chart for full list of vertical and horizontal dimensions at different bed lengths and degrees of incline

STANDARD SPECIFICATIONS
BELT – Black Trackmate 120 Roughtop with PVC cover SPEED REDUCTION – Sealed worm gear C-face speed reducer
BED – 6 1/2 in. deep x 12 ga. powder coated steel channel frame. with No. 50 roller chain to drive pulley
Standard 4 ft., 6 ft., 8ft. and 10 ft. long bolt-together sections with splice MOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan
plates. Bolt-in 12 ga. galvanized slider pans. cooled brake motor, energy efficient
DOUBLE NOSE-OVER – A 26 in. long horizontal and 12 in. long nose- FRAME CAPACITY – Maximum load per linear foot of conveyor is
over section provides a 2 stage transition from incline to horizontal. 100 lbs. Not to exceed drive capacity in chart.
Provides 30 degrees of adjustment.
POWERED INFEED – Short section of slider bed belt conveyor chain
driven from tail pulley of incline LOAD CAPACITY (LBS.)
BELT 25° INCLINE W/ ROUGHTOP BELT
CENTER DRIVE – Located on incline bed section. Chain guard is on WIDTH
FPM HP 24' 44'
left hand side when standing at infeed looking toward discharge.
• DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. 10"-16" 819 813
Machined crowned and fully lagged. 35 1 18"-24" 813 805
28"-36" 805 791
• TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at
10"-16" 434 426
bearings. Machined crown.
1 18"-24" 429 420
• TAKE-UP – Provides 16 in. of belt take-up in center drive. 28"-36" 420 406
65
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 10"-16" 883 875
1 3/16 in. dia. shaft at bearing. Machined crown. 2 18"-24" 877 868

SNUB / NOSE-OVER ROLLERS – Adjustable 2 1/2 in. dia. rollers. 28"-36" 868 855

Grease packed ball bearings. Includes guard. 10"-16" 277 269

1 18"-24" 272 263
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 28"-36" 263 250
bearings. 100
10"-16" 569 561
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive 2 18"-24" 563 554
and tail pulleys 28"-36" 555 541
BELT SPEED – Constant 65 FPM 10"-16" 202 194
1 18"-24" 196 187
28"-36" 188 174
135
10"-16" 418 410
2 18"-24" 412 403
28"-36" 404 390

10
 SECTION VIEW "X-X"
OVERRALL FRAME WIDTH
BOLT-IN
SLIDER PAN BETWEEN FRAME WIDTH 1-1/2"

BELT WIDTH
3/8"
3-3/8"

6-1/2"

8" CENTER DRIVE

2-1/2" DIA. SNUB IDLER/
1.9" RETURN IDLER
CROSS
MEMBERS

TOTALLY ENCLOSED
CHAIN GUARD

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place
of adjustments. Specify top of belt elevation. One support is required of 4 in. when not furnished as standard.
at every bed joint and at ends of conveyor. Holes in feet are provided
for lagging to floor. Knee braces supplied on SMS-3 support and UNDERTRUSSING – Available under incline bed sections in place
above. of floor supports or ceiling hangers. Maximum bed length is 40 ft.
Maximum belt width is 24 in. See bed and undertrussing information.
BELT – Brown polymate roughtop w/ nitrile cover, pure gum rubber
roughtop GUIDE RAILS – Adjustable channel guard rails, fixed angle and
channel guide rails.
BELT SPEED – Other constant and variable speeds: 17-135 FPM in
any increment. Contact factory for speeds not listed above. OTHER ACCESSORIES – Ceiling hangers. See accessory section.
MOTORS – Premium energy efficient, single phase, other ELECTRICAL CONTROLS – One direction manual start switch,
characteristics. 2 HP maximum. reversing drum switch, non-reversing and reversible IEC starters, push
button stations, AC variable frequency drive.
OTHER DRIVE VARIATIONS
• Side mount center drive
• End drive with underhung or side mount drive. Requires
underside take-up.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

11
BRI
INCLINE BELT CONVEYOR
(Roller Bed)
The BRI belt conveyor is ideal for transporting heavier products
from floor-to-floor or as a booster conveyor in gravity flow
systems. The roller bed design reduces belt friction and provides
greater capacity. It includes an adjustable double nose-over to
ensure smooth transfer from incline to horizontal that can be easily
adjusted up to 30 degrees. The frame design makes it ideal for
matching up with other roller bed conveyors.

n 12 belt widths
n Double nose-over
n Readily bolts up to other roller bed conveyors in a system

CONVEYOR WEIGHTS (LBS.)

DIMENSIONS @ 25° WITH BELT WIDTH BELT WIDTH
4" DIA. TAIL PULLEY * 10" 12" 14" 16" 18" 20" 22" 24" 28" 30" 34" 36"
OVERALL BETWEEN FRAME WIDTH OVERALL BETWEEN FRAME WIDTH
BED HORIZONTAL LENGTH LENGTH
LENGTH VERTICAL DISTANCE (REF.) 13" 15" 17" 19" 21" 23" 25" (REF.) 27" 31" 33" 37" 39"
LIFT ALONG OVERALL FRAME WIDTH OVERALL FRAME WIDTH
"VL" FLOOR 16" 18" 20" 22" 24" 26" 28" 30" 34" 36" 40" 42"
"HF"
4 IN. DIA. TAIL PULLEYS 6 IN. DIA. TAIL PULLEYS

10' 4' - 7" 12' - 10" 13'-10" 669 726 792 842 899 954 1,020 14' 1,344 1,485 1,565 1,714 1,792
12' 5' - 5" 14' - 7" 15'-10" 699 759 827 880 939 998 1,069 16' 1,399 1,543 1,626 1,779 1,861
14' 6' - 3" 16' - 5" 17'-10" 730 792 862 917 980 1,042 1,118 18' 1,453 1,601 1,687 1,844 1,929
16' 7' - 1" 18' - 3" 19'-10" 763 828 899 955 1,020 1,084 1,165 20' 1,505 1,655 1,744 1,903 1,990
18' 8' - 0" 20' - 1" 21'-10" 792 861 934 992 1,061 1,128 1,214 22' 1,559 1,713 1,805 1,968 2,058
20' 8' - 10" 21' - 10" 23'-10" 822 893 967 1026 1,096 1,166 1,256 24' 1,606 1,763 1,857 2,023 2,115
22' 9' - 8" 23' - 8" 25'-10" 852 926 1,002 1,063 1,137 1,210 1,305 26' 1,660 1,821 1918 2,088 2,184
24' 10' - 6" 25' - 6" 27'-10" 881 959 1,037 1101 1,178 1,254 1,355 28' 1,715 1,879 1,980 2,153 2,252
26' 11' - 4" 27' - 4" 29'-10" 913 992 1,071 1,135 1,213 1,291 1,395 30' 1,759 1,926 2,028 2,204 2,304
28' 12' - 2" 29' - 1" 31'-10" 942 1,024 1,106 1,172 1,254 1,335 1,445 32' 1,813 1984 2,089 2,269 2,372
30' 13' - 0" 30' - 11" 33'-10" 972 1,056 1,139 1206 1,290 1,372 1,487 34' 1,860 2,034 2,141 2,323 2,429
32' 13' - 11" 32' - 9" 35'-10" 1,002 1,089 1,174 1,243 1,330 1,416 1,536 36' 1,915 2,092 2,203 2,388 2,498
34' 14' - 9" 34' - 7" 37'-10" 1,031 1,122 1,209 1,280 1,371 1460 1,585 38' 1,969 2,150 2,264 2,453 2,566
36' 15' - 7" 36' - 4" 39'-10" 1,063 1,155 1,242 1,315 1,407 1,498 1,626 40' 2,013 2,197 2,312 2,504 2,618
38' 16' - 5" 38' - 2" 41'-10" 1,092 1,188 1,277 1,352 1,447 1,541 1,675 42' 2,068 2,255 2,374 2,569 2,686
40' 17' - 3" 40' - 0" 43'-10" 1,122 1,220 1,310 1,385 1,483 1,579 1,717 44' 2,115 2,305 2,425 2,624 2,743
* See incline dimensional chart for full list of vertical and horizontal dimensions at different bed lengths and degrees of incline

STANDARD SPECIFICATIONS
BELT – Black Trackmate 120 Roughtop with PVC cover SPEED REDUCTION - Sealed worm gear C-face speed reducer
BED – 6 1/2 in. deep x 12 ga. powder coated steel channel frame with with No. 50 roller chain to drive pulley
1.9 dia. roller x 16 ga. tube spaced every 6 in. Standard 4 ft., 6 ft., 8ft. MOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan
and 10 ft. long bolt-together sections with splice plates. cooled brake motor, energy effient
DOUBLE NOSE-OVER – A 26 in. long horizontal and 12 in. long nose- FRAME CAPACITY – Maximum load per linear foot of conveyor is
over section provides a 2 stage transition from incline to horizontal. 225 lbs. Not to exceed drive capacity in chart.
Provides 30 degrees of adjustment.
POWERED INFEED – Short section of roller bed belt conveyor chain LOAD CAPACITY (LBS.)
driven from tail pulley of incline. BELT 25° INCLINE W/ ROUGHTOP BELT
FPM HP WIDTH 24' 44'
CENTER DRIVE – Located on incline bed section. Chain guard is on
left hand side when standing at infeed looking toward discharge. 10"-16" 1,240 1,224
• DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. 35 1 18"-24" 1,232 1,207
Machined crowned and fully lagged. 28"-36" 1,216 1,181
10"-16" 652 636
• TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at
1 18"-24" 645 619
bearings. Machined crown.
28"-36" 629 593
• TAKE-UP – Provides 16 in. of belt take-up in center drive 65
10"-16" 1,341 1,322
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearing or 6 in. dia. with 2 18"-24" 1,330 1,305
1-3/16 in. dia. shaft at bearing. Machined crown. 28"-36" 1314 1,279
SNUB / NOSE-OVER ROLLERS – Adjustable 2 1/2 in. dia. rollers. 10"-16" 415 396
Grease packed ball bearings. Includes guard. 1 18"-24" 405 379
28"-36" 389 353
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 100
10"-16" 861 842
bearings. 2 18"-24" 850 825
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive 28"-36" 834 799
and tail pulleys 10"-16" 300 281
BELT SPEED – Constant 65 FPM 1 18"-24" 289 261
28"-36" 273 238
135
10"-16" 630 611
2 18"-24" 619 594
28"-36" 603 568

12
 SECTION VIEW "X-X"

8" CENTER DRIVE

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range PULLEYS – 6 in. dia. tail with 1-3/16 in. dia. shaft at bearing in place
of adjustments. Specify top of belt elevation. One support is required of 4 in. when not furnished as standard.
at every bed joint and at ends of conveyor. Holes in feet are provided
for lagging to floor. Knee braces supplied on SMS-3 support and UNDERTRUSSING – Available under incline bed sections in place
above. of floor supports or ceiling hangers. Maximum bed length is 40 ft.
Maximum belt width is 24 in. See bed and undertrussing information.
BELT – Brown polymate roughtop w/ nitrile cover, pure gum rubber
roughtop GUIDE RAILS – Adjustable channel guide rails, fixed angle and
channel guide rails.
BELT SPEED – Other constant and variable speeds: 17 - 135 FPM in
any increment. Contact factory for speeds not listed above. OTHER ACCESSORIES – Ceiling hangers. See accessory section.

MOTORS – Premium energy efficient, single phase, other ELECTRICAL CONTROLS – One direction manual start switch,
characteristics. reversing drum switch, non-reversing and reversible IEC starters, push
2 HP maximum. button stations, AC variable frequency drive.

OTHER DRIVE VARIATIONS

• Side mount center drive
• End drive with underhung or side mount drive. Requires
underside take-up.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

13
INCLINE DIMENSIONAL
CHART
(MODELS BSI & BRI)

DEGREE OF INCLINE
INCLINE 7.5° 10° 12.5° 15° 17.5° 20° 22.5° 25° 27.5 30 OVERALL
BED LENGTH
LENGTH VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF VL HF (REF.)

10 1' - 5" 13' - 9" 1' - 10" 13' - 8" 2' - 4" 13' - 7" 2' - 10" 13' - 5" 3' - 3" 13' - 4" 3' - 8" 13' - 2" 4' - 2" 13' - 0" 4' - 7" 12' - 10" 5' - 0" 12' - 7" 5' - 5" 12' - 4" 13' - 10"

12 1' - 8" 15' - 9" 2' - 3" 15' - 8" 2' - 9" 15' - 6" 3' - 4" 15' - 5" 3' - 10" 15' - 3" 4' - 5" 15' - 1" 4' - 11" 14' - 10" 5' - 5" 14' - 7" 5' - 11" 14' - 4" 6' - 5" 14' - 1" 15' - 10"

14 1' - 11" 17' - 8" 2' - 7" 17' - 7" 3' - 2" 17' - 6" 3' - 10" 17' - 4" 4' - 5" 17' - 2" 5' - 1" 16' - 11" 5' - 8" 16' - 8" 6' - 3" 16' - 5" 6' - 10" 16' - 2" 7' - 5" 15' - 10" 17' - 10"

16 2' - 2" 19' - 8" 2' - 11" 19' - 7" 3' - 8" 19' - 5" 4' - 4" 19' - 3" 5' - 1" 19' - 0" 5' - 9" 18' - 10" 6' - 5" 18' - 6" 7' - 1" 18' - 3" 7' - 9" 17' - 11" 8' - 5" 17' - 7" 19' - 10"

18 2' - 5" 21' - 8" 3' - 3" 21' - 6" 4' - 1" 21' - 4" 4' - 10" 21' - 2" 5' - 8" 20' - 11" 6' - 5" 20' - 8" 7' - 3" 20' - 5" 8' - 0" 20' - 1" 8' - 8" 19' - 8" 9' - 5" 19' - 4" 21' - 10"

20 2' - 8" 23' - 8" 3' - 7" 23' - 6" 4' - 6" 23' - 4" 5' - 5" 23' - 1" 6' - 3" 22' - 10" 7' - 1" 22' - 7" 8' - 0" 22' - 3" 8' - 10" 21' - 10" 9' - 8" 21' - 6" 10' - 5" 21' - 0" 23' - 10"

22 3' - 0" 25' - 8" 3' - 11" 25' - 6" 4' - 11" 25' - 3" 5' - 11" 25' - 0" 6' - 10" 24' - 9" 7' - 10" 24' - 5" 8' - 9" 24' - 1" 9' - 8" 23' - 8" 10' - 7" 23' - 3" 11' - 5" 22' - 9" 25' - 10"

24 3' - 3" 27' - 7" 4' - 4" 27' - 5" 5' - 4" 27' - 3" 6' - 5" 27' - 0" 7' - 6" 26' - 8" 8' - 6" 26' - 4" 9' - 6" 25' - 11" 10' - 6" 25' - 6" 11' - 6" 25' - 0" 12' - 5" 24' - 6" 27' - 10"

26 3' - 6" 29' - 7" 4' - 8" 29' - 5" 5' - 10" 29' - 2" 6' - 11" 28' - 11" 8' - 1" 28' - 7" 9' - 2" 28' - 2" 10' - 3" 27' - 9" 11' - 4" 27' - 4" 12' - 5" 26' - 9" 13' - 5" 26' - 3" 29' - 10"

28 3' - 9" 31' - 7" 5' - 0" 31' - 5" 6' - 3" 31' - 2" 7' - 5" 30' - 10" 8' - 8" 30' - 6" 9' - 10" 30' - 1" 11' - 0" 29' - 7" 12' - 2" 29' - 1" 13' - 4" 28' - 7" 14' - 5" 27' - 11" 31' - 10"

30 4' - 0" 33' - 7" 5' - 4" 33' - 4" 6' - 8" 33' - 1" 8' - 0" 32' - 9" 9' - 3" 32' - 5" 10' - 7" 31' - 11" 11' - 10" 31' - 6" 13' - 0" 30' - 11" 14' - 3" 30' - 4" 15' - 5" 29' - 8" 33' - 10"

32 4' - 3" 35' - 7" 5' - 8" 35' - 4" 7' - 1" 35' - 1" 8' - 6" 34' - 8" 9' - 10" 34' - 4" 11' - 3" 33' - 10" 12' - 7" 33' - 4" 13' - 11" 32' - 9" 15' - 2" 32' - 1" 16' - 5" 31' - 5" 35' - 10"

34 4' - 6" 37' - 6" 6' - 0" 37' - 4" 7' - 6" 37' - 0" 9' - 0" 36' - 8" 10' - 6" 36' - 2" 11' - 11" 35' - 9" 13' - 4" 35' - 2" 14' - 9" 34' - 7" 16' - 1" 33' - 11" 17' - 5" 33' - 2" 37' - 10"

36 4' - 9" 39' - 6" 6' - 5" 39' - 3" 8' - 0" 38' - 11" 9' - 6" 38' - 7" 11' - 1" 38' - 1" 12' - 7" 37' - 7" 14' - 1" 37' - 0" 15' - 7" 36' - 4" 17' - 0" 35' - 8" 18' - 5" 34' - 11" 39' - 10"

38 5' - 1" 41' - 6" 6' - 9" 41' - 3" 8' - 5" 40' - 11" 10' - 1" 40' - 6" 11' - 8" 40' - 0" 13' - 3" 39' - 6" 14' - 10" 38' - 10" 16' - 5" 38' - 2" 17' - 11" 37' - 5" 19' - 5" 36' - 7" 41' - 10"

40 5' - 4" 43' - 6" 7' - 1" 43' - 2" 8' - 10" 42' - 10" 10' - 7" 42' - 5" 12' - 3" 41' - 11" 14' - 0" 41' - 4" 15' - 8" 40' - 8" 17' - 3" 40' - 0" 18' - 10" 39' - 2" 20' - 5" 38' - 4" 43' - 10"

Note: Dimensions “VL” and “HF” are based on 4" tail pulleys. For 6" tail pulleys, overall length increases by 2 inches and dimensions “VL” and “HF” will change slightly.
Contact factory if exact dimensions are required.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

14
BED & UNDERTRUSSING
INFORMATION
(MODELS BRI & BSI)

SECTION VIEW “X-X”

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

15
TBOH
TROUGHED BELT CONVEYOR
(Overhead Conveying/Parts Handling)

The TBOH belt conveyor, with its built-in guide rails is ideal
for overhead conveying applications or applications where
product orientation is not the main focus. Typical products
include boxes, cases, cartons, bags or loose parts.

n Smooth, slim design

n Coped ends
n Troughed bed
n 10 belt widths

CONVEYOR WEIGHTS (LBS.)

BELT WIDTH
OVERALL 6" 8" 10" 12" 14" 16" 18" 20" 24" 30"
LENGTH BETWEEN SIDE GUIDES
OVERALL BED
WITH
LENGTH LENGTH 7" 9" 11" 13" 15" 17" 19" 21" 25" 31"
CENTER
DRIVE OVERALL BED WIDTH
8" 10" 12" 14" 16" 18" 20" 22" 26" 32"

6' 5' 6' 235 251 267 283 299 315 331 347 378 418
4 IN. DIA. DRIVE PULLEY

11' 10' 11' 295 315 335 355 375 395 415 435 475 531
16' 15' 16' 345 369 393 417 440 464 488 512 559 633
21' 20' 21' 413 441 469 497 524 500 528 556 616 733
26' 25' 26' 465 497 529 561 591 558 590 623 691 832
31' 30' 31' 527 563 599 635 669 627 663 700 777 938
36' 35' 36' 510 598 637 678 726 673 712 752 837 1,021
41' 40' 41' 644 687 730 758 816 755 798 843 938 1,143
46' 45' 46' 675 721 737 816 875 800 847 896 998 1,224
51' 50' 51' 758 809 860 911 961 882 933 985 1,095 1,342
56-4" 55' 56' 856 909 938 1,029 1,095 1,010 1,069 1,129 1,253 1,529
8 IN. DIA. DRIVE PULLEY

61-4" 60' 61' 935 998 1,061 1,124 1,185 1,092 1,155 1,220 1,364 1,673
66-4" 65' 66' 974 1,033 1,099 1,167 1,242 1,138 1,204 1,272 1,424 1,754
71-4" 70' 71' 1,055 1,126 1,197 1,268 1,339 1,228 1,289 1,371 1,523 1,866
76-4" 75' 76' 1,093 1,159 1,234 1,311 1,394 1,273 1,338 1,424 1,583 1,947
81-4" 80' 81' 1,169 1,248 1,327 1,406 1,484 1,366 1,434 1,515 1,684 2,071
86-4" 85' 86' 1,177 1,281 1,364 1,449 1,539 1,400 1,483 1,568 1,744 2,152
91-4" 90' 91' 1,214 1,370 1,457 1,544 1,629 1,482 1,569 1,657 1,870 2,327
96-4" 95' 96' 1,325 1,405 1,495 1,587 1,686 1,528 1,618 1,709 1,930 2,408
101-4" 100' 101' 1,414 1,494 1,588 1,682 1,776 1,610 1,704 1,800 2,001 2,472

STANDARD SPECIFICATIONS LOAD CAPACITY (LBS.)

HORIZONTAL W/ STANDARD BELT 25° INCLINE
BELT – Black Trackmate 120 EMB 8" DRIVE W/ ROUGHTOP
BELT 4" DRIVE PULLEY BELT
BED – 4 in. deep x 12 ga. powder coated steel slider bed with 2 1/2" PULLEY
WIDTH
deep guides. Standard 5 ft. and 10 ft. long bolt-together sections with FPM HP 11' 31' 51' 77' 101' 11' 31'
splice plates. 6"-16" 800 790 770 740 720 330 325
END DRIVE – Located on discharge end of conveyor. Chain guard is on 1/2
18"-30" 790 760 720 680 640 325 315
left hand side when standing at infeed looking toward discharge. 35
6"-16" 825*† 1,730* 1,710* 1,690 1,660 725* 715*
1
DRIVE PULLEY – 4 in. dia. with 1 in. dia. shaft at bearings or 8 in. 18"-30" 825*† 1,690* 1,660* 1,620 1,580 715* 700*
dia. with 1 7/16 in. dia. shaft at bearings. Machined, crowned and fully 6"-16" 470 450 430 405 390 195 185
lagged. 1/2
18"-30" 450 420 390 340 300 185 175
TAIL PULLEY – 4 in. dia. with 1 in. dia. shaft at bearings. Machined 6"-16" 825† 1,030 1,010 980 960 435 425
crown. 65 1
18"-30" 825† 1,000 960 920 880 425 415
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball 6"-16" 825*† 2,090* 2,070* 2,050 2,030 875* 870*
bearings. Includes guard. 2
18"-30" 825*† 2,060* 2,030* 1,980 1,950 865* 855*
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 6"-16" 325 310 290 265 240 135 125
1/2
bearings. 18"-30" 310 275 245 195 160 130 115
TAKE-UP – Provides 4 in. of belt take-up at tail pulley 6"-16" 720 705 690 660 640 300 290
100 1
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive 18"-30" 710 675 640 595 555 295 280
and tail pulleys 6"-16" 825† 1,430 1,415 1,390 1,365 600 595
2
BELT SPEED – Constant 65 FPM 18"-30" 825† 1,400 1,370 1,320 1,280 595 580
6"-16" 250 235 215 190 170 105 95
SPEED REDUCTION – Sealed worm gear C-face speed reducer with 1/2
No. 50 roller chain to drive pulley 18"-30" 235 200 170 120 85 95 85
6"-16" 535 520 500 475 455 225 215
MOTOR – 1/2 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan 135 1
18"-30" 520 485 455 405 370 215 205
cooled, energy efficient
6"-16" 825† 1,100 1,085 1,055 1,035 465 455
FRAME CAPACITY – Maximum load per linear foot of conveyor is 2
18"-30" 825† 1,070 1,035 990 950 455 445
75 lbs. Not to exceed drive capacity in chart.
* Requires 8" diameter drive pulley in lieu of 4" diameter. †Limited by conveyor capacity.

16
4" END DRIVE
OVERALL LENGTH

6" BED LENGTH 6"

4" DIA.
DRIVE PULLEY FLOW 4" DIA.
TAIL PULLEY

NIP POINT GUARD X NIP POINT GUARD

1.9" DIA.
2-1/2" DIA. RETURN IDLER
SNUB IDLER TAKE-UP
4-3/4"

15-1/2"
MAX.
2-1/2" DIA.
SNUB IDLER
11-1/4"
22-3/4"
MAX.

34" MAX.

12" APPROX.
X

OPTIONAL SMS
SUPPORT SHOWN

SECTION VIEW X - X 8" END DRIVE 4" SHAFT MOUNTED DRIVE

8-1/8"
OVERALL BED WIDTH
2-1/2" DIA. OVERALL LENGTH
3-3/4" BED WIDTH 1/2" SNUB IDLER FLOW
10" BED LENGTH
L.H. R.H. 8" DIA.
SIDE BELT WIDTH SIDE
DRIVE PULLEY

2-1/2" 16-1/2" 9-1/8"

MAX 12-1/2"
MAX
4"
5-5/8"
11-1/4"
28" 3-1/4"
MAX 6"
39" MAX 12" APPROX. REF.

7-1/8" *
2-1/8" DIA. OPTIONAL SMS MIN. ELEV.
SNUB IDLER
SUPPORT SHOWN

TOTALLY ENCLOSED CHAIN GUARD

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range CENTER DRIVE / TAKE-UP – Provides 16 in. of belt take-up and is
of adjustments. Specify top of belt elevation. One support is required suitable for reversing applications.
at every bed joint and at ends of conveyor. Holes in feet are provided • Standard underhung drive (4 in. dia. drive pulley): 16 in.
for lagging to floor. Knee braces supplied on MS-7 support and minimum elevation. 78 in. minimum OAL.
above. • Standard underhung drive (8 in. dia. drive pulley): 17 in.
minimum elevation. 78 in. minimum OAL.
BELT –Tan Glidetop, White Polymate 100 RMP – COS, Black
• Side mount drive/low elevation center drive (4 in. or 8 in. dia.
Trackmate 120 Roughtop with PVC cover
drive pulley): 13 1/2 in. minimum elevation. 66 in.
BELT SPEED – Other constant and variable speeds minimum OAL.
• 4 in. dia. drive pulley: 35, 40, 50, 65, 80, 100 and 135 FPM
OTHER DRIVE VARIATIONS – Side mounted end or center drives
• 8 in. dia. drive pulley: 35 – 135 FPM in any increment
• Contact factory for speeds not listed above UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends
down 13 1/8 in. from top of belt.
HIGHER SIDES – 4 in., 6 in., 9 in. or 12 in. high vertical sides (12 in.
maximum) GRAVITY BRACKETS – Brackets and support bar allows skate wheel
or 1 3/8 in. dia. gravity roller conveyor to be supported at end of belt
OTHER PULLEY OPTIONS
conveyor. Includes 1 in. dia. pop-out transfer roller.
• 8 in. dia. drive pulley with 1 7/16 in. dia. shaft at bearings in lieu
of 4 in. dia. drive pulley BUTT COUPLINGS – Brackets allow 1.9 in. / 2 in. dia. gravity roller
• 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in lieu of conveyor along with other conveyors to be attached to end of belt
4 in. dia. tail pulley conveyor. Includes 1 in. dia. pop-out transfer roller. Center drive or
• 1 1/8 in. dia. nose roller assembly in lieu of 4 in. dia. tail pulley. underside take-up recommended if butt couplings are to be located at
Center drive is required. tail end.
MOTORS – Premium energy efficient, single phase, brake motor, OTHER ACCESSORIES – Floor supports with casters, poly-tier
other characteristics. 2 HP maximum. supports, ceiling hangers. See accessory section.
SHAFT MOUNTED END DRIVE – 4 in. dia. drive pulley only. Drive ELECTRICAL CONTROLS – One direction manual start switch,
unit mounted on extended pulley shaft. Mounting bracket and torque reversing drum switch, non-reversing and reversible IEC starters, push
arm enable multiple mounting positions. 4 7/8 in. minimum elevation. button stations, AC variable frequency drive.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

17
TBTH
TROUGHED BELT CONVEYOR
(Trash Handling)
With its 6 in. high guide rails and minimal belt gap between
guide rails, the TBOH belt conveyor is ideal for handling
empty cardboard boxes and paper trash.
n Troughed bed
n 8 belt widths
n Center drive and take-up

CONVEYOR WEIGHTS (LBS.)

BELT WIDTH
12" 18" 24" 30" 36" 42" 48" 54"
OVERALL BED BETWEEN FRAME WIDTH
LENGTH LENGTH 13" 19" 25" 31" 37" 43" 49" 55"
OVERALL FRAME WIDTH
16" 22" 28" 34" 40" 46" 52" 58"
4 IN. DIA. TAIL PULLEY 6 IN. DIA. TAIL PULLEY

12' 10' 732 867 1,002 1,137 1,272 1,408 1,542 1,676
22' 20' 974 1,152 1,330 1,508 1,686 1,865 2,042 2,219
32' 30' 1,216 1,437 1,658 1,879 2,100 2,322 2,542 2,762
42' 40' 1,458 1,722 1,986 2,250 2,514 2,779 3,042 3,305
52' 50' 1,700 2,007 2,314 2,621 2,928 3,236 3,542 3,848
62' 60' 1,942 2,292 2,642 2,992 3,342 3,693 4,042 4,391
72' 70' 2,184 2,577 2,970 3,363 3,756 4,150 4,542 4,934
82' 80' 2,426 2,862 3,298 3,734 4,170 4,607 5,042 5,477
92' 90' 2,668 3,147 3,626 4,105 4,584 5,064 5,542 6,020
102' 100' 2,910 3,432 3,954 4,476 4,998 5,521 6,042 6,563
112' 110' 3,152 3,717 4,282 4,847 5,412 5,978 6,542 7,106
122' 120' 3,394 4,002 4,610 5,218 5,826 6,435 7,042 7,649
132' 130' 3,636 4,287 4,938 5,589 6,240 6,892 7,542 8,192
142' 140' 3,878 4,572 5,266 5,960 6,654 7,349 8,042 8,755
152' 150' 4,120 4,857 5,594 6,331 7,068 7,806 8,542 9,278

STANDARD SPECIFICATIONS LOAD CAPACITY CHART (LBS.)

HORIZONTAL 15" INCLINE
BELT – Black Trackmate 120 EMB W/ ROUGHTOP
BELT W/ STANDARD BELT BELT
BED – 7 1/2 in. deep x 1 1/2 in. flange by 12 ga. powder coated steel WIDTH
FPM HP 27' 52' 77' 102' 152' 27' 52'
channel frame with bolt-in slider pans and cross members. 6 in. high
guards. Bed sections bolt together with endcaps. 24"-36" 1,906 1,863 1,822 1,779 1,695 1,024 1,000
1
CENTER DRIVE / TAKE-UP – Underhung center drive with chain 48"-54" 1,870 1,806 1,744 1,680 1,555 1,004 970
35
guard located on left-hand side when standing at infeed looking toward 24"-36" 3,172 3,129 3,088 3,045 2,961 1,073 1,680
2
discharge 48"-54" 3,136 3,072 3,010 2,946 2,820 1,684 1,649
24"-36" 991 948 907 864 780 532 601
• DRIVE PULLEY – 8 in. dia. with 1 7/16 in. dia. shaft at bearings. 1
48"-54" 955 891 829 766 640 513 565
Machined, crowned and fully lagged. 65
24"-36" 1,673 1,630 1,589 1,546 1,461 898 875
• TAKE-UP PULLEY – 6 in. dia. with 1 3/16 in. dia. shaft at 2
48"-54" 1,637 1,573 1,511 1,447 1,321 879 845
bearings 24"-36" 617 575 533 490 406 331 309
1
• TAKE-UP – Provides 16 in. of belt take-up in center drive 100
48"-54" 582 518 456 392 266 309 278
24"-36" 1,060 1,018 976 933 849 569 546
TAIL PULLEY - 4 in. dia. with 1 in. dia. shaft at bearings or 6 in. dia. with 2
48"-54" 1,025 961 899 835 709 550 516
1 3/16 in. dia. shaft at bearing. Machined crown.
24"-36" 438 395 353 311 226 235 212
SNUB ROLLERS – Adjustable 2 1/2 in. dia. rollers. Grease packed ball 1
48"-54" 402 338 276 212 86 216 181
bearings. Includes guard. 135
24"-36" 766 723 681 639 554 411 388
2
RETURN ROLLERS – Adjustable 1.9 in. dia. rollers. Grease packed ball 48"-54" 730 666 604 540 414 392 357
bearings.
BEARINGS – Sealed, pre-lubricated, self-aligning, ball bearings on drive
and tail pulleys
BELT SPEED – Constant 65 FPM
DUST PANS – 16 ga. underside dust cover
SPEED REDUCTION - Sealed worm gear C-face speed reducer with
No. 60 roller chain to drive pulley
MOTOR – 1 HP – 230/460 V – 3 phase – 60 Hz totally enclosed fan
cooled, energy effieient
FRAME CAPACITY – Maximum load per linear foot of conveyor is 10
lbs. Not to exceed drive capacity in chart.

18
 FLOW

SECTION VIEW X-X

OVERALL FRAME WIDTH

INCLINE WITH NOSE-OVER AND INFEED

OPTIONAL EQUIPMENT
FLOOR SUPPORTS – SMS floor supports are available in wide range 8 IN. END DRIVE – Requires underside take-up
of adjustments. Specify top of belt elevation. One support is required • Underhung end drive: 16 1/2 in. minimum elevation. 103 in.
at every bed joint and at ends of conveyor. Holes in feet are provided minimum OAL.
for lagging to floor. • Side mount end drive: 10 in. minimum elevation.
95 in. minimum OAL.
BELT – Black Trackmate 120 Roughtop with PVC cover
INCLINE WITH NOSE-OVER AND INFEED - 5, 10, 12-1/2, 15, or 20
BELT SPEED – Other constant and variable speeds: 17-135 FPM in degree (See drawing below)
any increment. Contact factory for speeds not listed above.
• NOSE-OVER – Fixed degree nose-over section providing
PULLEYS - 6 in. dia. tail pulley with 1 3/16 in. dia. shaft at bearings in transition from incline to horizontal
place of 4 in. when not furnished
• TWO-PULLEY HITCH – Fixed degree section providing
MOTORS – Inverter duty, premium energy efficient, single phase, transition from horizontal infeed to incline while allowing one
brake motor, other characteristics. 2 HP maximum. belt to be used for infeed and incline
SIDE MOUNTED CENTER DRIVE / TAKE-UP – Provides 16 in. HIGHER GUIDE RAILS – 12 in., 18 in., or 24 in. high vertical sides.
of belt take-up and is suitable for reversing applications. 12 1/2 in. 30 degree flare is also available.
minimum elevation. 66 in. minimum OAL.
ELECTRICAL CONTROLS – One direction manual start switch,
UNDERSIDE TAKE-UP – Provides 16 in. of belt take-up. Extends reversing drum switch, non-reversing and reversible magnetic starters,
down 13 1/8 in. from top of belt. push button stations, AC variable frequency drive.

Roseville, Michigan • Phone: (586) 771-1881 • www.ultimationinc.com

19