Scribd
Upload
61 views2 pages

TDS en Bitoner Resin C9 BT-120

BITONER BT-120 is a thermoplastic aromatic resin used primarily in industrial paints and adhesives, known for its excellent compatibility, low molecular weight, and good thermal and moisture resistance. It is packaged in 25kg bags or bulk bags and has specific properties such as a softening point of 115-125°C and a maximum acid value of 0.1 mgKOH/g. The product is compliant with various U.S. FDA regulations for adhesives and coatings.

Uploaded by

Daniela Tovar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
61 views2 pages

TDS en Bitoner Resin C9 BT-120

BITONER BT-120 is a thermoplastic aromatic resin used primarily in industrial paints and adhesives, known for its excellent compatibility, low molecular weight, and good thermal and moisture resistance. It is packaged in 25kg bags or bulk bags and has specific properties such as a softening point of 115-125°C and a maximum acid value of 0.1 mgKOH/g. The product is compliant with various U.S. FDA regulations for adhesives and coatings.

Uploaded by

Daniela Tovar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Typical Analysis Datasheet

BITONER C9 BT-120

Product Description
BITONER BT-120 is thermoplastic, slightly yellow granular aromatic resin obtained from petroleum-derived
monomers. It is compatible with many resins,mineral oils,vegetable oils and plasticizers. Soluble in major
solvents in industrial paints and adhesives.It is mainly used in industrial paints and adhesives.

Key Characteristics:
·Excellent compatibility with other resins
·Low Molecular weight
·Good thermal resistance
·Good resistance to acids, alkalis and moisture
·Water resistance

Typical Properties
Property Test method Unit Typical value
Color (50% resin solid in Toluene) (ASTM D1544) Ga # Max 10#
Softening point (Ring & Ball) (ASTM E28) °C 115-125
Acid value (ASTM D974) mgKOH/g Max 0.1
Iodine Value (ASTM D1959) gI/100g Max 30
Ash Content (ASTM D1063) % Max 0.05
Specific gravity, @25℃ (ASTM D71) g/cm³ 1.07-1.13

Application
Industrial paints, Solvent adhesives, Asphalt Modification, Sealants

Package
25kgs net Kraft Paper bag or 500kgs/1000kgs in bulk bags.

QINGDAO BATER CHEMICAL CO., LTD.


No. 6 Shandong Road, Qingdao 266071 China Tel +86-532-55662730/31/32/39, Fax +86-532-55662725
Email: [email protected] Websites: www.bitoner.com

Disclaimer: All information in this publication is in accordance with our present experience and knowledge. However, since
we have no influence on the way in which our products are treated and used, we cannot take any responsibility in this respect.
The user must assume responsibility himself for checking whether the products are suitable for the purpose and use proposed
by him. All existing proprietary rights, laws and regulations shall be observed. The information in this publication cannot be
considered as a guaranty. Due to the technical conditions in the production, the above-mentioned information may vary.

Storage: All resins with a low softening point present a risk of solidifying or lump.It increases in hot weather or if stored near
heat sources. Thus for softening points less or equal to 110℃, we recommend: storage in a cool (25℃ max), ventilated place.
Avoid exposuring to direct sunlight and storage for prolonged period. Do not stack pallets and keep far away from heat sources.

Regulatory Status
U.S. FDA: 21 CFR 175.105 Adhesives
21 CFR 175.300 Resinous and polymeric coatings
21 CFR 177.2600 Rubber articles intended for repeated use

You might also like