BHARATIYA VIDYA BHAVAN’S

SARDAR PATEL INSTITUTE OF TECHNOLOGY

MUNSHI NAGAR, ANDHERI(W), MUMBAI 400058

ASSIGNMENT-2
CO2 Analyze the properties of a continuous time signal in frequency domain and observe
the spectrum.

Branch: EXTC Semester: III (S.E.)

Subject: Signal, Network and Systems (SNS EC203)

Module 2 Fourier Series and Fourier Transform: CO2

Q1.Find the trigonometric fourier series expansion of a periodic signal x(t). Equation of one
period of a signals is x (t) = A t; 0 ≤ t ≥ 1

Q2.State and prove multiplication property and convulation property in Fourier transform.

Q3.LTI system is descrived by the differential equation,

+ 2𝑦 𝑡 𝑥 𝑡

Calculate ouptut y(t) if input x(t) = e-3t u(t) is applied to the system.

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q4.Obtain Trigonometric Fourier Series Expansion for the signal shown below. Also find
corresponding co-efficients of exponential F.S.

T = 1sec

Q5. Obtain exponential Fourier series for the rectangular pulse train show in the figure and
sketch the spectrum

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 BHARATIYA VIDYA BHAVAN’S

SARDAR PATEL INSTITUTE OF TECHNOLOGY

MUNSHI NAGAR, ANDHERI(W), MUMBAI 400058

ASSIGNMENT-3
CO3 Evaluate Linear Time Invariant system response using Laplace Transform

Branch: EXTC Semester: III (S.E.)

Subject: Signal, Network and Systems (SNS EC203)

Module 3 Analysis of CT System

Q 1) Deduce the relation between Laplace Transform and Fourier Transform

Q 2) Obtain transfer function of the following electrical system. Gain of buffer Amplifier = 1.

Q 3) Determine the laplace transform of the sine pulse

Q 4) State and prove time integration and time differentiation property of laplace transform.

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q 5) Determine the laplace transform of the following periodic signal

Q 6) Determine the inverse laplace of X(s)

Q 7) Using Laplace Transform, determine the natural response of system described by equation

Q 8) Perform Convolution of following signals using time domain. Verify your result using
Laplace tranform

Q 9) If 𝑋 𝑠 ; Find the Laplace Transform of the following signals

a. y(t) = x(2t - 1) u(2t - 1)

b. y(t) = t x(t)

c. y(t) = x(t) cos7t

Q 10) Find the inverse Laplace Transform of 𝐹 𝑠 if ROC is

a. s > 3 b. s < -1 c. 1<s<3

Q 11) Determine the initial and final values of signal x(t) whose Laplace transform

X(s) =

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q 12) Obtain inverse Laplace Transform for all possible ROCs

𝑋 𝑠 ;

Q 13) The input signal to an LTI System having an impulse response h(t) is x(t) = est.
Show that output of the system y(t) is given by signal y(t)=est H(s)

Q 14) Classify system as linear/non-linear, causal/non-causal, time variant/time-

invariant, memory/memoryless.

a. y(t) = x(-t)

b. y(t) = 2 x(t) + 3

Q 15) State whether following signals are linear or non-linear

a. y(t) = x2(t)

b. y(t) = t x(t)

Q 16) For the following given electrical network, obtain its transfer function.

Q 17) Determine the impulse response for the system H(s) = ; Also, find the
-3t
response of the system for input x(t) = e u(t)

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q 18) Find the response of the system having equation

y"(t) + y’(t) – 2y(t) =u’(t) + 2u(t)

with initial conditions: y(0-) = 1 and y’(0-) = -1

Q 19) Determine convolution of the following functions using graphical method. Also
verify your result using Laplace transform.

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 BHARATIYA VIDYA BHAVAN’S

SARDAR PATEL INSTITUTE OF TECHNOLOGY

MUNSHI NAGAR, ANDHERI(W), MUMBAI 400058

ASSIGNMENT-4
CO4 Analyse RLC circuits in time domain and frequency domain

Branch: EXTC Semester: III (S.E.)

Subject: Signal, Network and Systems (SNS EC203)

Module 4 & 5 Transient Analysis and Network Synthesis

Q 1) For series R-L-C network subjected to unit step input, determine the effect of damping for
various damping cases: underdamped, undamped, critically damped, overdamped. What will
be effect if damping factor (ζ) is made negative?

Q 2) The switch has been closed for a long time. It is open at t=0. Compute

Q 3) Determine the current i(t) for t > 0, when switch is closed at t = 0.

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q 4) Check whether P(s) = s4 + 5s3 + 5s2 + 4s + 10 is Hurwitz or not.

Q 5) Test whether F(s) = (2s3 + 2s2 + 3s + 2)/(s2 + 1) is positive real function.

Q 6) List the properties of Positive Real Functions

Q 7) Determine the necessary and sufficient conditions for positive real functions.

Q 8) Determine the following functions in Foster-I and Foster-II form

Z(s) = [3(s + 2)(s + 4)]/[s(s + 3)]

Q 9) Determine the following Functions in Cauer I and Cauer II form

F(s) = (s2 + 2s +2)/(s2 + s + 1)

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 BHARATIYA VIDYA BHAVAN’S

SARDAR PATEL INSTITUTE OF TECHNOLOGY

MUNSHI NAGAR, ANDHERI(W), MUMBAI 400058

ASSIGNMENT-5
CO5 Design and analyze Butterworth filter

Branch: EXTC Semester: III (S.E.)

Subject: Signal, Network and Systems (SNS/ EC203)

Module 6 Filter Design & Realisation: CO5

Q 1) Determine the transfer functon H(s) and the amplitude response H(jw) for a third-order
lowpass Butterworth filter if the 3 dB cut off frequency ωc = 100. Find your answer without
using Tables. Verify your answer using either of these tables.

Q 2) Determine n, the order foa lowpass Butterworth filter, and the corresponding cut-off
frequency ωc required to satisfy the following lowpass filter specifications. Find both the
values of ωc, the one that oversatisfies the passband specificatopns, and the one that
oversatisfies the stopband specifications.

a) 𝐺 p ≥ - 0.5 dB, 𝐺 s ≤ -20 dB, ωp =100 rad/sec and ωs = 200 rad/sec

b) Gp ≥ 0.9885, Gs ≤ 10-3, ωp =1000 rad/sec and ωs = 2000 rad/sec

c) The gain at 3 ωc is required to be no greater than -50 dB

Q 3) Design a Butterworth highpass filter to meet the specifications :

The 𝐺 ≥ -1 dB, 𝐺 s ≤ -20 dB ωp =20 rad/sec and ωs = 10 rad/sec

Q 4) Demonstrate the steps for realization of a filter using Direct Form -I and Direct Form -II
filter.

Q 5) Realize the filter as demonstrated by following equation in Direct Form-II form

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
Prof. Najib Ghatte EngineeringWithNajibSir
9821867642 Subscribe to YouTube Channel
 BHARATIYA VIDYA BHAVAN’S

SARDAR PATEL INSTITUTE OF TECHNOLOGY

MUNSHI NAGAR, ANDHERI(W), MUMBAI 400058

ASSIGNMENT-6
Branch: EXTC Semester: III (S.E.)
Subject: Signal, Network and Systems (SNS EC203)

Module Self Study

Q 1) Obtain the State Space Model for the given Electrical Network

Q 2) Obtain state model for the transfer function given as

H(s) =

Q 3) Estimate the current flowing through 10 Ω resistor using Thevenin’s Theorem.

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
 Q 4) Investigate the dual of the following network

Q 5) Investigate tie-set matrix of the following network

Q 6) Estimate the current Ix flowing through 5 Ω resistor using Superposition Theorem

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
Q 7) Estimate the nodal voltages V1 and V2 using Nodal Analysis

Q 8 ) Consider the network shown in the figure using loop method of analysis, inspect the
currents in all the branches, indicating their directions. Use graph theory method

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel
Q 9) Determine Y-parameters of the following interconnected network

Q 10) Determine ABCD Parameters of the following network

Prof. Najib Ghatte EngineeringWithNajibSir

9821867642 Subscribe to YouTube Channel