H12-931_V2.0-ENU HCIE-Transmission (Written) V2.

0 exam dumps questions

are the best material for you to test all the related Huawei exam topics. By using
the H12-931_V2.0-ENU exam dumps questions and practicing your skills, you
can increase your confidence and chances of passing the H12-931_V2.0-ENU
exam.

Features of Dumpsinfo’s products

Instant Download
Free Update in 3 Months
Money back guarantee
PDF and Software
24/7 Customer Support

Besides, Dumpsinfo also provides unlimited access. You can get all
Dumpsinfo files at lowest price.

HCIE-Transmission (Written) V2.0 H12-931_V2.0-ENU exam free dumps

questions are available below for you to study.

Full version: H12-931_V2.0-ENU Exam Dumps Questions

1.What are the options for the logic function modules involved in clock information processing?
(Multiple choice)
A. RST
B. SETS
C. SPI
D. MCF
Answer: B.C.

2. Mapping is the process of adapting branch signals into () at the boundary of the SDH network.
Answer: Virtual container
3.OptiX trans E9624 subrack supports cross-mode change. After changing from 1:1 mode to 1:3
cross-mode, it can be restored to 1:1 cross-mode by rollback.
A. True
B. False
Answer: B

4. During network commissioning, if it is found that the OSNR does not meet the standard, which of
the following methods can be used to solve it? (Multiple choice)
A. Use Raman amplifiers to replace some EDFA amplifiers
B. Use high-performance FEC instead of low-performance FEC
C. Adding electrical relay sites
D. Adjust the optical amplifier to ensure that all amplifiers are working in the nominal state
Answer: BCD

5. Which of the following IP addresses is a Class C IP address?

A. C2.A8.D2.e1
B. 10.110.192.111
C. 10011010.01101110.10000000.01101111
D. 127.0.0.1
Answer: A

6. Which of the following methods can be used to achieve service isolation in the network-side
transmission tunnel of PTN equipment? (Multiple choice)
A. MPLS
B. VLAN
C. S-VLAN
D. IP
Answer: ABC

7.SPC software permanent connection. It is a service connection between PC and SC. The user to
network part is directly configured by the network management plane, while the network part
connection is initiated by the network management plane to the entry network element control plane,
and the entry network element control plane completes it through signaling.
A. True
B. False
Answer: A

8. The GFP protocol is highly standardized. It is the standard way to map data services to SDH/OTN.
Which of the following characteristics of the GFP protocol is correct? (Multiple choice)
A. GFP currently supports frame-mapped and transparent mapping.
B. Capable of statistical multiplexing of user data signals
C. It can more effectively prevent frame errors caused by bit errors and is more conducive to the
interconnection and interoperability of various manufacturers
D. Support point-to-point or ring network service configuration
Answer: ABCD
9. In general, which PHB is used for signaling?
A. CS7, CS6
B. EF
C. BE
D. AF1, AF2, AF3, AF4
Answer: A

10.1588 V2 clock model mainly consists of OC, BC, E2E TC and P2P TC. Which of the following is
not a feature of OC? (Multiple choice)
A. Contains data sets: one clock data set, N port data sets
B. Message processing: Except for signaling messages and management messages, all other
messages are terminated or generated at the node.
C. Contains multiple physical ports: Each physical port communicates with the network through two
logical interfaces (cvent and general interface)
D. Contains data sets: including clock identity, number of ports, delay mechanism
Answer: CD

11. Synchronization means that the signals maintain a certain strict relationship in frequency or
phase, that is, their corresponding effective moments appear at the same average rate.
A. True
B. False
Answer: A

12. When the optical cable is laid by traction, the main traction force should be applied to the () of the
optical cable.
Answer: Strengthening components

13. For a 10G OTU board, the receiving optical module uses a PIN module. Which of the following
receiving powers is within the normal receiving range of the board?
A. -9dBm
B. -19dBm
C. 9dBm
D. 19dBm
Answer: A

14. Optical Wavelength Sharing Protection (OWSP) is used to configure a ring network for distributed
services. It protects one distributed service between all sites by occupying two different wavelengths,
and can protect multiple services at the same time.
A. True
B. False
Answer: B

15. The tunnel-level APS protection of Hybrid MSTP equipment can support forced switching and
locked switching, and the priority of forced switching is higher than that of locked switching.
A. True
B. False
Answer: B

16. Which of the following descriptions of the networking requirements for configuring SOM is wrong?
A. OSC board must be configured in the network
B. The outbound optical amplifier at the OMS segment must be equipped with an MCA board
C. An OA board must be configured between the FIU board and the ROADM board or the
splitter/combiner board at the receiving end of the OMS segment
D. Optical amplifier boards of the same dimension can be inserted into different network elements
Answer: D

17. The low-order path overhead byte V5 in VC12 is similar in function to which of the following
overhead bytes in the high-order path overhead of VC4? (Multiple choice)
A. J1
B. G1
C. C2
D. B3
Answer: BCD

18. Automatic gain control (AGC) can solve the problem in multi-wavelength systems where the
increase or decrease in wave number causes energy transfer, thereby affecting the optical power of
the normal operating wavelength.
A. True
B. False
Answer: A

19. Faults can be effectively and promptly eliminated and services restored by resetting boards,
restarting stations, re-issuing configurations, or transferring services to backup channels. Therefore,
maintenance personnel can prioritize their previous experience in troubleshooting.
A. True
B. False
Answer: B

20. When the OSN 8800 T32 cabinet emits an alarm buzzer, which of the following methods can be
used to turn off the alarm sound?
A. Long press the RESET button on the main control panel
B. Set the ID switch of the main control board to 0.
C. Turn off the TEST switch on the top of the cabinet
D. Long press the alarm cut-off switch on the main control board
Answer: D

21.Which of the following items are optional items for microwave station commissioning?
A. Align the antenna
B. Test ECC
C. Clock tracking test
D. Testing business
Answer: C

22. 424.1588V2 clock enters non-trace working mode, report alarm CLOCK_NO_TRACE_MODE,
which of the following are possible reasons? (Multiple choice)
A. Some nodes in the network have the SSM protocol enabled, while others do not.
B. The system clock source priority table is not configured, and the network element uses its own
default priority table
C. In the clock source priority table, all clock sources except the internal source are lost or the
frequency deviation is too large.
D. When 1588V2 frequency synchronization is enabled, the configuration or link is abnormal
Answer: ABCD

23. When OTN equipment is connected to Cisco equipment, the number of CRC error packets on the
Cisco equipment interface is relatively large. Which of the following is the impossible reason?
A. Abnormal connection optical power
B. The bit error rate on the line side of the OTN equipment is large
C. The type of interconnected optical module is wrong.
D. The interconnected optical module is faulty.
Answer: C

24. The clock ID can solve the problem of timing loops that may occur. In the following network, how
many clock IDs need to be set in total to completely solve the clock loop?

A.3
B. 4
C. 6
D. 7
Answer: C

25. When the capacity of the cross-connect board is upgraded, if a site with dual cross-connect
configuration is replaced, there will be two cross-connect boards with different capacities coexisting.
At this time, if the cross-connect board is switched, there will be a long service interruption.
A. True
B. False
Answer: B

26.HONET integrated service access network belongs to () access method.

Answer: Fiber Optic
27. Aligning antennas means aligning the main lobes of the antennas at both ends to maximize the
signal strength received from the opposite antenna.
A. True
B. False
Answer: A

28.SOTU stands for Single Optical Transport Unit Interface, while MOTU stands for Multiple Optical
Transport Unit Interface.
A. True
B. False
Answer: A

29.CES services can be simulated based on SDH VC-4 signals and VC-12 signals.
A. True
B. False
Answer: A

30. In the OLT+ONU combined networking mode, OLT mainly plays the role of (), so the OLT
equipment is required to have good performance and be able to provide sufficient bus bandwidth.
Answer: Convergence

31. The IP address you use is 165.247.52.119, and the subnet mask is 255.255.240.0. Which subnet
is your host on?
A. 165.247.52.0
B. 165.247.32.0
C. 165.247.56.0
D. 165.247.48.0
Answer: D

32. Which of the following descriptions about 1+1 protection and 1:1 protection of MPLS Tunnel is
correct? (Multiple choice)
A. If you want to protect the MPLS Tunnel, you need to create an MPLS Tunnel protection group.
B. Services protected by MPLS Tunnel 1+1 are sent and received selectively at both ends, while
services protected by MPLS Tunnel 1:1 are sent and received singly.
C. The services of MPLS Tunnel 1:1 protection include dual-end switching and single-end switching,
while MPLS-Tunnel 1+1 protection only includes single-end switching.
D. The APS protocol of MPLS Tunnel 1:1 protection transmits protocol status and switching status to
each other through the tunnel.
Answer: ABD

33. The maximum output power of the OAU105 board in the OTN system is 23dBm. It can be inferred
that the maximum output optical power of a single wavelength in the 40-wave system is 4dBm.
A. True
B. False
Answer: B

34. When configuring 1+1 optical line protection, you can select RI1/TI2/TO2 as the working channel
according to actual conditions.
A. True
B. False
Answer: B

35. The following is the network parameter planning of an engineer's network management server.
Which of the following is correct? (Multiple choice)
A. Network management server host name: server123-
B. IP address planning for a single-machine system (Windows): IP address: 192.9.1.1/255.255.255.0;
Gateway: 123.9.1.254
C. Equivalent network element: 2000 network servers, the planned bandwidth for managing network
elements is 3.02Mbit/s
D. A network with 200 equivalent network elements, a collection period of 15 minutes, and 7 days of
performance data retention. The planned performance database size is 80 GB.
Answer: BCD

36. To which step does GetEventChannel belong in the working principle of CORBA?
A. Session maintenance
B. Session Warning
C. Information Query
D. Session initialization
Answer: D

37. Which of the following statements is correct? (Multiple choice)

A. Veritas is a high-reliability system consisting of a volume manager, a volume controller, and local
cluster software.
B. In any case, the standby machine does not write data to the data replication cache.
C. The volume manager and volume replicator manage disks in the house through logical volumes,
so the operating system and U2000 are both located here.
D. Local dual-machine, Linux can use bond mode to connect to the outside world, and supports
floating IP
Answer: ABD

38. When multiple alarms are reported, the priority principle of alarm processing is to process and
troubleshoot the alarms in the order of equipment alarms (BUS_ERR, HARD_ERR, COMM FAIL,
etc.), optical layer LOS, electrical layer OTUk_LOF, ODUk_SSF, and protection type protection
switching.
A. True
B. False
Answer: A

39. A service passes through two wavelength division rings. The two wavelength division rings are
tangentially networked. The tangential network elements share the electronic rack. It is required to
implement segmented ODURSKCP protection, that is, the protection is interrupted once for each fault
in each ring. Which of the following types should be configured?
A. SNC/N
B. SNC/S or SNC/N
C. SNC/S
D. SNC/1
Answer: B

40. OptiX OSN 3500 equipment forms a SNCP ring network, the cross-connect board uses GXCSA,
and the main ring is configured with SL64 boards. AB is two adjacent nodes. Station B receives a
large number of regeneration section and multiplex section errors reported by the SL64 board of
station A. At the same time, station A receives the multiplex section far-end errors reported by the
SL64 board of station E. After studying the network diagram, it is found that the distance between A
and B is 100km, the rate is 10G, and the configuration structure is " Optical board + BA + PA + DCU +
optical board".
Which of the following reasons lead to bit errors? (Multiple choice)
A. The problem of matching the cross-connect board and the circuit board causes bit errors
B. Wrong DCU module model
C. Insufficient BA+PA gain leads to bit errors
D. Bit errors caused by optical board failure
Answer: BCD

41. Two SMP rings intersect. For cross-ring services, the configuration of the intersection nodes is
particularly important. In order to achieve the best protection effect, each intersection node needs to
be configured with one unidirectional cross connection and two pairs of SNCP protection groups.
A. True
B. False
Answer: B

42. If there is a problem with the call quality, you can adjust the voice quality by setting the port gain
at both ends on the network management. When the port volume is low, increase the call gain; when
the port volume is high, reduce the call gain.
A. True
B. False
Answer: A

43. The U200 network management system supports multiple external interfaces. When connecting
to equipment from other manufacturers, which of the following interfaces can be used? (Multiple
choice)
A. MML
B. SNMP
C. Qx
D. CORBA
Answer: ABD

44. When which of the following pointers is adjusted, the information payload area carries the most
information payload?
A. Positive adjustment
B. Negative Adjustment
C. No adjustment
D. All of the above are possible
Answer: B

45. The frame rate () and transmission rate of different levels of STM levels are different.
Answer: Same

46. Which of the following descriptions of modulation technology for 40Gbit/s and 100Gbit/s coherent
systems are correct? (Multiple choice)
A. The modulation technology used in 100G coherent systems is ePDM-BPSK
B. The modulation technology used in the 40G coherent system is ePDM-QPSK
C. The modulation technology used in the 100G coherent system is ePDM-QPSK
D. The modulation technology used in the 40G coherent system is ePDM-BPSK\
Answer: CD

47. A path is a transmission entity consisting of a pair of "one-way paths" that can transmit
information in opposite directions between their respective outputs and inputs at the same time.
A. True
B. False
Answer: A

48. In order to achieve the specified synchronization quality requirements, corresponding

requirements must be made for the synchronous transmission network, and certain networking rules
must be followed during network planning. Which of the following is wrong?
A. In one clock transmission direction, the number of stations between transit office clocks cannot
exceed 30.
B. The number of switching station clocks cannot exceed 10
C. The total number of devices in one direction cannot exceed 60
Answer: A

49. When configuring the basic properties of the EM20 board Ethernet interface, the default value of
the "maximum frame length" is ().
A. 1522
B. 1491
C. 1490
D. 9600
Answer: D

50. In a point-to-point WDM networking scenario, the signal-to-noise ratio of a single channel is low,
while other channels are normal. What is the reason for this being impossible?
A. The optical power of the OTU board corresponding to this wave at the transmitting end has
decreased
B. The fiber pigtail attenuation from the OTU board corresponding to this wave to the combiner
increases
C. Increased attenuation on the optical path
D. The gain slope of the amplifier changes
Answer: C

51. Which of the following reasons will result in discrete services in network management? (Multiple
choice)
A. In the 5.0 platform device, a network element in a complete path is not in the current network
management
B. The cross-connection of the intermediate network element service is not configured
C. A complete path is configured between the online network element and the pre-configured network
element
D. Two NE services in the same NMS. Under the premise of selecting the correct time slot, the cross
connection of one NE is issued through U2000, and the other is issued through command line
software and the NMS is not uploaded.
Answer: BD

52.When configuring the dual-stage amplifier board of RAU+OAU, where is the best location for the
DCM module in the following figure?

A. 1
B. 2
C. 3
D. 4
Answer: C

53.Which of the following options are correct? (Multiple choice)

A. SATop encapsulation type processes CES services by packaging the 32 time slots in the E1 frame
as a whole and then transparently transmitting them to the other end.
B. The CESoPSN protocol can identify the structure of TDMN services. It does not need to transmit
idle time slot channels. It only extracts useful time slots from the service flow and encapsulates them
into PWE3 messages for transmission.
C. PCM30 frame format of E1 frame: except time slot 0 which is used as synchronization time slot
and does not carry voice, time slot 16 also cannot carry voice because it is used to transmit random
signaling.
D. PCM31 frame format of E1 frame: except for 16 time slots as synchronization time slots that do not
carry voice, it can also carry 31 channels of voice.
Answer: ABD

54. Which of the following statements about the position of the dispersion module in the signal flow is
wrong?
A. If there is an OAU board, the DCM is placed between the TDC/RDC of the OAU
B. If there is only one OBU board, the DCM is placed after the OBU
C. If there are two OBU boards, the DCM is placed between the two OBUs.
D. OTM station usually pre-fills 20KM DCM before sending OBU
Answer: B

55. The DWDM system has extremely high requirements on the stability of the light source. Which of
the following factors affect the stability of the light source? (Multiple choice)
A. Temperature
B. Driving current
C. Packaging
D. Humidity
Answer: ABC

56. Which of the following descriptions of the 100G hybrid transmission system is wrong?
A. Coherent and incoherent signals (10G, 40G ODB) will affect each other, causing a sharp drop in
performance, and isolation is necessary.
B. 40G DQPSK and phase signals will not affect each other, and no isolation band is required
C. During mixed transmission, the coherent signal starts from the long wavelength, 10G starts from
the short wavelength, and the isolation band can be filled with 40G DQPSK wavelength
D. The mixed transmission cost is related to the number of transmission spans and the width of the
isolation band, and has nothing to do with the FEC encoding method.
Answer: D

57. What types of boards need to be upgraded when upgrading NG-SDH equipment?
A. 123
B. 321
C. 213
D. 312
Answer: C

58. A network is configured with 1+1 protection on the board. One day, the working channel has the
conditions to trigger protection switching, but the service cannot be automatically switched to the
protection channel, resulting in service interruption. Which of the following may be the cause of the
fault? (Multiple choice)
A. Protection group parameter configuration error
B. A lock switch or forced switch command is implemented
C. Single board optical fiber link error
D. The protection channel fails
E. Host version defects
F. The relay board between sources is wrongly configured.
Answer: ABCDEF

After the 286.10G system wavelength division commissioning is completed, it is found that the OSNR
value of the single board scanned by the receiving end MCA is very good, but the pre-correction bit
error rate is very poor. Which of the following are the possible reasons? (Multiple choice)
A. Dispersion compensation is unreasonable
B. Improper optical power adjustment
C. Light balance station is used in the middle
D. Line loss is greater than the design value
Answer: AC

59. Which of the following descriptions of SNMP is wrong?

A. SNMP (Simple Network Management Protocol) is the Simple Network Management Protocol.
B. SNMP can be used between upper and lower layer network management, and can also be used
between devices and network management.
C. The northbound structure of SNMP includes OSS (Operating Support System) and Agent. SNMPA
is a session layer protocol that specifies how to transfer management information between NMS and
Agent.
D. The SNMP southbound protocol specifies how to transmit information between the U2000 and
network element devices.
Answer: C

60.SOM is an intelligent management solution for the optical layer, which is only used for single-
wavelength optical power and OSNR detection of coherent 40G and 100G systems.
A. True
B. False
Answer: B

61. What are the main application scenarios of 1588 ACR? (Multiple choice)
A. Traversing an asynchronous network
B. Traversing a rented third-party network
C. Huawei SDH Network
D. Huawei PTN Network
Answer: A-B

62. Which of the following is wrong about DCN network planning? (Multiple choice)
A. The network management server and each managed NE communicate with each other using in-
band networking or out-of-band networking. In-band networking refers to the networking mode in
which the U2000 manages the devices in the network by using the service channels provided by the
managed devices.
B. Huawei transport domain network elements support three communication protocols for DCN
networking, among which the HWECC protocol is a private communication protocol developed by
Huawei for transport domain network elements DCN networking.
C. The IP address of U2000 is "129.9.0.100/24, and the IP address of the gateway NE it manages is
129.9.0.2/24. If U2000 wants to communicate with an NE connected to the gateway NE with an IP
address of 133.168 0.2/24 through IP Over DCC, U2000 and the gateway NE need to be directly
connected.
D. Huawei transport domain network elements all support the HWECC protocol, and the physical
transmission channel defaults to bytes D1 to D12. When the network element ID is set, ECC
communication can be performed without any configuration after the optical fiber is plugged in.
Answer: CD

63. Which of the following options are correct regarding the reasons why the optical layer path (OCH
level) may cause route calculation failure? (Multiple choice)
A. The optical fiber attenuation between the TDC and RDC ports of the OAU board is too large.
B. The wavelength of the WDM-side port of the OTU board is inconsistent with the wavelength of the
optical cross-connection
C. Fiber optic connection error
D. Network layer OTS path missing
Answer: BCD

64. When a faulty board is found at the beginning of the project, after calling TAC to locate the fault,
you can go through the DOA process and directly apply for spare parts.
A. True
B. False
Answer: A

65. Before performing optical power adjustment on the ROADM board, you must first configure virtual
optical layer services, otherwise the ROADM board will block all wavelengths by default.
A. True
B. False
Answer: A

66. A company has built a network with 20 subnets and Class C IP addresses. What subnet mask
should be used to correctly configure the network?
A. 255.255.255.248
B. 255.255.255.224
C. 255.255.255.192
D. 255.255.255.240
Answer: A

67. The SCC board of the slave rack 2 of OSN6800 reports the communi_fail alarm. The third bit of
the parameter is 0X04. The network element is not disconnected. There are no abnormal alarms in
the master rack and slave rack 1. Which of the following are the possible causes of the fault?
(Multiple choice)
A. Main subrack AUX board failure
B. The AUX board in slave rack 2 is faulty.
C. The AU parent board of the subrack is faulty.
D. The network cable between subracks 2 and 3 is faulty.
Answer: BCD
68.TE links in OTN electrical layer ASON are unidirectional. For example, there are two TE links
between NS2 and NS2. The final number of links is the number of ports on the N boards that have
been enabled (including the relay N boards).
A. True
B. False
Answer: A

69. Which of the following options are correct about solving the system OSNR limitation problem?
(Multiple choice)
A. Coherent reception using a local oscillator laser of the same frequency to interfere with the
received optical signal to improve the OSNR tolerance.
B. Using enhanced HEC correction coding, it improves OSNR by nearly 1dB compared to AFEC.
C. Use low noise figure NF, high performance EDF A and Raman amplifier boards, such as
TN130AU106 or TRAU106, to improve the system's receiving OSNR.
D. Use advanced modulation and coding technology to reduce the baud rate and improve OSNR
tolerance.
Answer: BCD

70. After a maintenance worker failed to start the CORBA interface, he listed several steps to check:
1. Check the log file
"%IMAPROOT%/server|varNVlogs\Develop\nbiAgent_CORBA\unbi_sys_yyyyMMdd_hhmmss_ ?
.log; 2. Check whether the u2000License file supports the U2000 CORBA interface function; 3. Check
whether the %IMAPRDOT%/server/ns.ior file is deleted.
Is his operation correct?
A. True
B. False
Answer: B

71.Which of the following ASON functions and features can both improve the controllability of the
service rerouting path and shorten the service rerouting time?
A. Business path pre-calculation
B. SRLG
C. Business Optimization
D. Preset recovery path
Answer: D

72.Instrument testing method is applicable to which of the following scenarios? (Multiple choice)
A. Eliminate external problems with the transmission equipment
B. Device connection issues
C. Locating the faulty board
D. Equipment performance indicator issues
Answer: ABCD

73.Which of the following options are commonly used test instruments for transmission systems?
(Multiple choice)
A. OTDR (Optical Time Domain Reflectometer)
B. SmartBits Tester
C. SDH Tester
D. Optical power meter
E. spectrum analyzer
Answer: ABCDE

74. () is called optical transmission segment in Chinese, and (OMS) is called optical multiplexing
segment in Chinese.
Answer: OTS

75. Which of the following comparisons of commonly used optical fibers G.652 and G.655 are
correct? (Multiple choice)
The core diameter of AG52 is larger than that of G.655
The chromatic dispersion coefficient of BG52 is smaller than that of G.655
CG52 can withstand greater fiber input power than G.655
The attenuation coefficient of DG52 is lower than that of G.655
Answer: AC

76. Hybrid MSTP equipment supports cross-domain clock intercommunication and supports the
intercommunication between synchronous Ethernet and SDH synchronization.
A. True
B. False
Answer: A

77. Each station of the high-speed rail CTC service has a () circuit.
Answer: 2M

78. On the U2000 network management system, the packet plane and TDM plane in the Hybrid
MSTP device can be managed in a unified manner to achieve end-to-end service interoperability.
A. True
B. False
Answer: A

79. The overhead ratio is a factor that affects the error correction capability of FEC technology.
Usually, under the same FEC encoding/decoding algorithm conditions, the higher the overhead ratio,
the greater the net coding gain.
A. True
B. False
Answer: B

80.Which of the following devices does not support PCM features?

A. OSN 2500
B. OSN 7500
C. OSN 550
D. OSN 3500
Answer: A

81. The insertion loss of the 40 split-wave channels of D40 is 6dB. Without considering the influence
of noise, when the signal is full, the optical power of the IN port of D40 is X dBm. If the optical power
of the IN port is decreases by 1dB, the measured value of one of the output ports is 6dBm. (Assuming
that the optical power of each channel is balanced, lg40=16)
A. (X-5)
B. (X-6)
C. (X-22)
D.(X-23)
Answer: D

82. A certain wavelength division network, the networking is shown in the figure.

Now, due to the need for new services, two waves need to be added and dropped at site B, that is,
the OLA site needs to be transformed into a back-to-back OTM site. Which of the following
descriptions is wrong?
A. To change the site type from OLA to back-to-back OTM, you need to add M40/D40/OA/OUT
boards. You need to evaluate whether the existing network subrack slots are sufficient. If a new
subrack is required, you need to evaluate whether there is space to install the new subrack.
B. Since the original network dispersion is normally compensated, it is not necessary to consider
adjusting the dispersion after the network transformation.
C. It is necessary to recalculate the design signal-to-noise ratio of each segment AB, BE, and AE to
evaluate whether the designed signal-to-noise ratio can meet the needs of business reception.
D. Perform optical power budgeting for the new service relay segment and redesign the power of the
transformed site according to the requirements of the back-to-back OTM site. If possible, add an
optical amplifier board.
Answer: B

83. Before configuring SOM, the physical fiber connection from OMCA to the optical amplifier board
must be completed. The logical fiber connection from OMCA to the optical amplifier board does not
affect the OMS path generation, and therefore does not affect the configuration of SOM.
A. True
B. False
Answer: B

84. The nonlinear effect of coherent signals is stronger than that of 10G incoherent signals, so the
single-wavelength optical power input to the fiber should be reduced. Therefore, during system
commissioning, the single-wavelength output optical power of the OA can be reduced by reducing the
OA gain to meet the optical power requirements of the fiber input.
A. True
B. False
Answer: B

85. Which of the following protections in microwave equipment does not require paired slots?
A. SD
B. FD
C. HSB
D. SD+FD
Answer: C

86. If both the bidirectional OA and OSC report a loss of light alarm in a WDM network, which is the
most likely cause?
A. One-way interruption of line optical fiber
B. The line optical fiber is interrupted in both directions
C. Unidirectional degradation of line fiber
D. Bidirectional degradation of line optical fiber
Answer: B

87. Which of the following statements about network element package loading and diffusion upgrade
is correct? (Multiple choice)
A. Configure activation grouping. Gateway NEs and non-gateway NEs cannot be grouped in the
same group.
B. The number of network elements for the packet diffusion upgrade task shall not exceed 15.
C. The package software upgrade task may not include the gateway network element
D. A packet diffusion software upgrade can include at most one gateway NE, and all non-gateway
NEs in the task must belong to the same gateway NE.
Answer: ABCD

88. Regarding ODUk ring network protection, which of the following statements is wrong?
A. Each service is bound by a segment ID to achieve the unique difference between services.
B. The node where the management point is located can have no business binding
C. The entire ring only needs to configure one node as the management point
D. Only the working channel service needs to be manually configured, and all protection channels are
automatically generated
Answer: B

89. When adding or deleting member ports in static aggregation, the LACP protocol must be run.
A. True
B. False
Answer: A

90. Which of the following protections does N3EGS2 support?

A. TPS
B. PPS
C. BPS
D. DLAG
Answer: C
 91. When shutting down the U2000 dual-machine system (Solaris), the following commands are
used:
What is the correct order in which these commands appear?
A. ????
B. ????
C. ????
D. ????
Answer: A

92. Which of the following is not a reason why the RAU Raman board cannot gain normally? (Multiple
choice)
A. Raman pump is not turned on
B. The current value of input optical power is -40dBm
C. Raman board failure
D. Return loss is too large
Answer: ACD

93. K1 and K2 bytes can transmit APS switching signaling and can also indicate the failure of the
signal of the multiplex section
A. True
B. False
Answer: A

Powered by TCPDF (www.tcpdf.org)