NOTES:-

1. ALL DIMENSIONS ARE IN MILLIMETERS UNLESS

NOTED OTHERWISE.
2. WRITTEN DIMENSIONS ARE TO BE FOLLOWED,
DRAWING ARE NOT TO BE SCALED.
3. LEVEL SHOULD BE DECIDED BY ENGINEER IN
CHARGE AT THE SITE.
4. UNLESS NOTED OTHERWISE SPECIFIED. ALL
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 REINFORCEMENT SHALL BE OF HIGH YEILD
CF-01 STRENGTH BARS OF GRADE FE-500D
3800
RAFT (D-750) CONFIRMING IS: 1786-1985 WITH MINIMUM YEILD
STRENGTH OF 500N/MM2.

250
5. UNLESS NOTED OTHERWISE SPECIFIED, ALL
EXISTING SHED

C1 ELEMENTS SHALL BE IN M-25.

4000
3500
1300
A 6. UNLESS NOTED OTHERWISE SPECIFIED, ALL
PCC WORK SHALL BE IN 1:3:6.
C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1

250
850 7. MIN. YIELD STRESS OF STRUCTURE MEMBER
EXISTING SHALL BE 250MPA.

4925

4450
SHED 380 MM THK. P.C.C. 1:3:6 8. ALL WELD SHALL BE IN ACCORDANCE WITH
COLUMNS R.R. MASONARY WALL 300MM THK. CLAUSE 11.6 OF IS:800-2007 AND IS:816.
111000 9. ALL WELDING SHALL BE AS PER IS 816-1969.
10. ALL ELECTRODES SHALL BE AS PER IS 814-1963.
11. ALL STRUCTURAL BOLTS ARE OF HIGHT
℄ OF B.G. TRACK TENSILE 8.8 GRADE (HSFD) O.N.G. MENTIONED
3100

CONFIRMING TO IS 400.
F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 F-2 D-450 12. SAFETY CODE FOR ERECTION OF STEEL
2000
6200

6200
STRUCTURE STEEL WORK AS PER. IS 7205-1974.
C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2 C2
13. THE WORK TO BE CARRIED OUT AS PER
3100

2000 TENDER CONDITIONS AND SPECIFICATION.

EXISTING SHED

3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000 14. ALL WELD ARE AS PER IS SPECIFICATION AND

21300

22250
AS PER THICKNESS OF MEMBER FLAT FULL
LENGTH ALL AROUND CONTINUES.
℄ OF B.G. TRACK 15. ALL GUSSET PLATES ARE 12MM THICK UNLESS
OTHERWISE MENTIONED.
16. PROVIDE 110MM RAIN WATER PIPE AT EVERY
6200

6200
COLUMN.
17. THE STRUCTURE SHOWN IN THIS DRAWING IS A
PRE-ENGINEERED BUILDING (P.E.B.)
℄ OF B.G. TRACK 18. FOUNDATION NOTES:-
18.1. SAFE BEARING CAPACITY AS PER SOIL
INVESTIGATION REPORT IS 15.37 T/M² AT
111000 1.5M FROM NATURAL GROUND LEVEL.
EXISTING 380 MM THK. CF-01 P.C.C. 1:3:6 19. REFERENCE:-

4450
4925

R.R. MASONARY WALL RAFT (D-750) 300MM THK. 19.1. IS CODE PRACTICE FOR GENERAL
EXISTING SHED

SHED
COLUMNS CONSTRUCTION IN STEEL (IS:800:2007)

250
850 19.2. IS CODE PRACTICE FOR COLD FORMED
LIGHT GAUGE STEEL STRUCTURE (IS.

4000
3500
1300

B 801:1975)
19.3. IS CODE PRACTICE FOR DESIGN LOAD
C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1 C1

250
PART-3 (IS.875:2015)
19.4. IS CODE PRACTICE FOR EARTHQUAKE
LOAD PART-1 (IS1893-2002)
250 1500 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 6000 1500 250
108000
111000
111500

FOOTING LAYOUT PLAN

380 MM THK.
R.R. MASONARY WALL 1300
850 850
W-910X12
6000 2F-450X20
W-910X12 RIB PL.
2F-450X20 200X250X12
32Ø-24NOS BOLTS
950MM LONG RIB PL. RIB PL.
125X200X12 32Ø-24NOS BOLTS 125X200X12 PEDESTAL (850X1300)
GROUTING

GROUTING
BASE PLATE 950MM LONG BASE PLATE
50

50
1200X700X32 1200X700X32 1300

C1 C1
PEDESTAL (850X1300)
C1
450

450
RAIL LEVEL RAIL LEVEL

PEDESTAL (850X1300)

850
750

750
#12-100C/C #12-100C/C #12-100C/C
1075 1100 1100
#12-100C/C
750

750
25Ø BARS 26 NOS. 10Ø RINGS 150C/C
P.C.C. 1:3:6
300MM THK.
300

300
250 P.C.C. 1:3:6 250 3500 250
#12-100C/C #12-100C/C
300MM THK. 4000
#12-100C/C
#12-100C/C

LONGITUDINAL SECTION CROSS SECTION SECTION OF PEDESTAL

t

32Ø-24NOS BOLTS RIB PL. W-910X12

950MM LONG 200X219X12 2F-450X20

125 153.6 128.6 128.6 128.6 128.6 128.6 153.6 125

ANCHOR BOLT
75

RIB PL.
131

125X200X12 NORTH WESTERN RAILWAY

SCHEDULE
125

AJMER DIVISION
PROJECT: PROPOSED SHED FOR B.G. WAGON
146

FACILITIES IN LOCO WORKSHOP AJMER

150

BOLT DESCRIPTION DIA. (MM) H (MM) h (MM) t (MM) TITLE: FOUNDATION & BASE PLATE DETAILS
BASE PLATE
700

146

(1200X700X32) 32MM DIA. BOLT 32 MM 950 MM 100 MM 150 MM CONTRACTOR: M/S ASLAM KHAN
H
150

146

DISIGN CONSULTANT: ADHIRACHNA ENGINEERING

125

SOLUTIONS
Villa No. 04, Aditi Villas, Jagatpura, Jaipur-302017
131

+91-9782812009; +91-9602443346
75

[email protected]; www.adhirachna.com

75 145 190 190 190 190 145 75

1200
8MM THK.
WELDING
90
°

BASE PLATE XEN/WORKSHOP/AJMER

h

(1200X700X32)
DY.CME/LOCO

ANCHOR BOLT SSE/WORKSHOP/AJMER

DRG. NO.:
DATE: SHEET SIZE: A1 SHEET: 01/05 R0