QUALIITYMANAGEMENT ISO 9001:2000 Coding: TD ED EN

Revision 03
Page 1 of 3

PRODUCT DATA SHEET

EGGER EURODEKOR® E1
Material Specification:
Specification:
Melamine faced wood-based panel with a decorative surface.
The substrate can be either EUROSPAN® Rawboard, EGGER MDF
or EGGER OSB Combiline
Area of application:
application:
Decorative wood based panels for interior uses.

Board type according to EN14322

Surface properties Test method Unit Value
Surface defects
-points [mm²/m²] ≤2
-length EN 14323 [mm/m] ≤20
Resistance to scratching
EN 14323 [N] ≥1,5
Resistance to staining
EN 14323 [level] ≥3
Resistance to cracking
EN 14323 [level] ≥3
Resistance to abrasion
Class IP WR
Depending on the layer 1 <50 <150
configuration different EN 14323 [Resolutions] 2 ≥50 ≥150
classes are reached 3A ≥150 ≥350
3B ≥250 ≥650

Tolerances Test method Unit Thickness range *1)

<15mm 15 up to 20mm >20 mm
Thickness
Standard boards (faced with single layer )
Final value *2) EN 14323 [mm] ±0,3 ±0,5/ -0,3
Boards with multi-layer surface
Final value *2) EN 14323 [mm] ±0,5
Length and width
• commercial available size ±5
EN 14323
• pre-cut panels [mm] ±2,5
Flatness
EN 14323 [mm/m] -- ≤2*3)
Edge damage
• commercial available size ≤10
EN 14323 [mm]
• pre-cut panels ≤3

Responsible: PM Decorative Release date: 18.05.2010

 QUALIITYMANAGEMENT ISO 9001:2000 Coding: TD ED EN
Revision 03
Page 2 of 3

Physical and chemical

characteristics Substrate Test method Unit Class
Fire behaviour
EURODEKOR® MFC EUROSPAN® raw board D-s2, d0
EURODEKOR MDF ® EGGER MDF D-s2, d0
EN 13501-1 Euro class
EURODEKOR® OSB COMBILINE EGGER OSB COMBILINE D-s2, d0
EURODEKOR Flammex
® EUROSPAN Flammex
®
B-s2, d0
Formaldehyde content
EURODEKOR® MFC EUROSPAN® raw board EN 717-2*4) [mg/m²h] ≤ 3,5*5)

EURODEKOR® MDF EGGER MDF EN 717-2*4) [mg/m²h] ≤ 3,5*5)

EURODEKOR® OSB COMBILINE EGGER OSB COMBILINE EN 717-2*4) [mg/m²h] ≤ 3,5*5)
EUROSPAN® JP F0.3
EURODEKOR® JP F0.3 (F****) JIS 1460 [HCOH/l] ≤ 0,30
(F****)
EURODEKOR E1 EPF-S EUROSPAN E1 EPF-S P2 DIN EN 120 [mg/100g] < 4,0*6)
Content of pentachlorophenol
CEN/TR 14283 [ppm] ≤5

For specific areas of use and fields of application it can be helpful to determine further board characteristics. These can be
carried out according to the testing methods of EN 14322:2003 between supplier and customer on request.
Property Test method
Resistance to cigarette burns EN 14323
Resistance to steam EN 14323
Resistance to impact by a large diameter steel ball EN 14323
Resistance to colour change in xenon arc light EN 14323
Gloss EN 14323
Surface soundness EN 311

Colour matching and surface texture:

When the customer requires colour or surface texture matching only a slight deviation (rating 4) is permissible between the
reference sample and test piece under examination. For pearlescent and metallic finished boards a rating of 3 is permitted for
colour matching by EN 14322: 2003. Slight variations in colour are inherent with variation in the surfacing papers and the core
board.

Field of application
EGGER EURODEKOR® manufactured with Type P2 raw board is intended for interior fittings (including furniture) for use in dry
conditions (relative humidity of surrounding area only exceeding 65% for a few weeks per year). The component must allow
quick release of any trapped moisture. Boards of this type are only suitable for use in biological hazard class 1 of EN 335-3.
EGGER EURODEKOR® manufactured with Type P3 core board can be used in humid conditions (relative humidity of surrounding
area only exceeding 85% for a few weeks per year). The component must allow quick release of any trapped moisture. Boards
of this type are only suitable for use in biological hazard classes 1 & 2 of EN 335-3. EGGER EURODEKOR® Melamine Faced
Boards are available in an impressive range of decors and colour matched EGGER laminates, edging material and foils.

General information
A careful control of incoming materials is an essential part of any commercial transaction. Therefore this is a part of the terms
of payment of delivery within the EGGER Group. EGGER recommends proceeding with these controls according to statistical
methods. Also the handling and storage of EURODEKOR® Melamine Faced Boards has to be done with care. The boards should

Responsible: PM Decorative Release date: 18.05.2010

 QUALIITYMANAGEMENT ISO 9001:2000 Coding: TD ED EN
Revision 03
Page 3 of 3

advisably be stored on a flat and dry base in a self contained building. The atmospheric humidity should not go over 75% for a
longer period of time. In case of longer storage periods under humid conditions the boards should be shrink-wrapped to avoid
swelling of the board's edges is advised. A continuous room temperature should be maintained between 10°C (50°F) and 50°C
(122°F).

Resistance against heat

The resistance against heat of EURODEKOR has to be subdivided in long and short terms of heat influence. For long or
continuous terms of heat influence a maximum temperature of 50°C is allowed. A temperature of max. 90°C (194°F) is allowed
for a time period of not more than 1 hour. Long term temperature application of more than 50°C might damage the surface by
cracks. Installations of technical equipment that emit heat require an appropriate distance between heat source and melamine
surface to avoid heat accumulation and divert temperature.

Additional documents
Technical Datasheets:
EUROSPAN® Raw chipboards, EGGER MDF, EGGER OSB COMBILINE

Provisional Note:
This technical datasheet contains information added carefully and under precise investigation. Technical details are subject to
change. The continuous development of EGGER EURODEKOR® might result in differences, as well as renewals of standards and
documents of public law. Therefore EGGER can give no guarantee for misprint, or mistakes. This technical datasheet is not an
instruction of use and not a legally binding document.

*1) Thickness range: nominal values

*2) Tolerances nominal value: The nominal value is the final thickness of the board including coatings on both sides of the boards
*3) Only with an equally balanced grammage of decorative papers on both sides
*4) Gas analysis
*5) Half years value
*6) Raw board testing in accordance with perforator methode

Responsible: PM Decorative Release date: 18.05.2010