PIPELINE REPAIR PRODUCTS FOR HIGH PRESSURE
PIPES IN THE OIL- GAS- AND PETROCHEMICAL INDUSTRY
for on shore installation
for. offshore installation, with zinc
anodes
and marine epoxy coating
weldable, with heat insulating gaskets
with girder rings, if required
Split sleeves are widely used for making repairs to a
variety of high or low pressure and high or low
Pipe Fit - Split Repair Sleeve
temperature pipelines, containing oil, water, gas, steam
and chemical fluids.
The clamp halves are joined by bolts to form a high
integrity pressure vessel around the damaged or leaking
pipe.
Sealing is provided by elastomer seals of the highest
quality selected for compatibility with the pipeline fluid
and operating temperature.
The Split sleeves may also be welded after installation to
provide a permanent repair. It may be completely seal welded with
the pipeline in operation
Standard, on shore type
Weldable split sleeves With girder Offshore type, with zinc anode
PIPELINE REPAIR PRODUCTS FOR HIGH PRESSURE
PIPES IN THE OIL- GAS- AND PETROCHEMICAL INDUSTRY
Design Features and Methods
Split Sleeve Material Specifications
Safety
The clamps are fully compensatory pressure vessels, ANSI pressure classes 300, 400, 600, 900 and 1500
hydrostatically tested to 1.3 times the rated working
pressure (as per ASME Sect ion VI I I Div.1 Design based on: ASME Sec. VIII, API 6H, ANSI
clause UG-99) B31.4, B31.8 and Split Sleeve Software 3S)
All Clamps are equipped with a 1/2” or 1” NPT vent Design control and stress analysis with Finite Element
port depending on size and client’s requirements. Package
Design Criteria and Industry Standards Body materials: A216 WCB, A216 WCC, A352 LCC,
All split sleeves are tested in accordance with the API A516 Gr.70 (Suitable for normally corrosive services)
Specification 6H, “Specification for End Closures,
Connectors, and Swivels”, ASME BOILER AND Stud material: A193 Gr. B7
PRESSURE VESSEL CODE, Section VIII; and with Nut material: A 194 Gr. 2H
ANSI standards B-31.3, B31.4, & B31.8, where
applicable. Coating: Yellow Epoxy Polyamide, standard or Marine
Certification: EN 10204 3.1 epoxy
Ease of Installation and Maintenance The highest quality NBR or VITON elastomer seal
All split sleeves are designed to be installed with the precisely compatible with the line fluid and ambient
most common tools available and are readily field temperature will be installed into the split sleeves.
repairable, including full seal replacement.
NBR temperature range is from - 20 ̊C to + 80 ̊C
Economy HNBR temperature range is from - 20 ̊C to + 150 C̊
Split Sleeve Repair Clamps are designed utilizing the VITON temperature range is from - 20 ̊C to + 200 C ̊
latest technology, allowing optimization of design
techniques and materials, resulting in lower weight, Gaskets are replaceable without any special tools.
Split Sleeves are suitable for sour environment Girder rings can be installed upon cleints request.
This type of split sleeve is designed to be used in
hydrogen sulfide (H2S) bearing hydrocarbon service. Double Row Sealing (DRS) design is also available.
For sour services, the body material will meet NACE This special design is more suitable for where
MR0175 probable
leakage is much costly or dangerous, such as
Certification and Testing gaseous services & offshore applications.
Nondestructive testing (NDT):
- 100 % magnetic particle inspection (MPI) for stiffener Weldable split sleeves
to shell weld (fillet) All clamps can be fully prepared for welding after
- 100 % ultrasonic testing of vent plug welds installation (welding procedure is available on
- 100 % MPI of hinge welds request).
Hydrotest as per ASME Section VIII Div.1 clause
UG-99 Heat insulators (parallel to the seals) protect the seals
from heat during the welding of the sleeves to the
pipe.
Clamps with longer lengths available on request.
