<br>
Q.89 What is the designated function of a 'planetary internal grinder machine'?
Ans 1. For a work piece of irregular shape
X 2. For a very small work piece
X 3. Fora work piece of regular shape
X 4. For low precision surface finishes
<br>
Q.17 Which of the following movements of the grinding wheel is possible in a chucking-type
internal grinder?
Ans X1.Only rotational movement
X2. Only vibrational movement
3. Both rotational and reciprocating movement
X 4. Only reciprocating movement
<br>
Q.57 Which of the following expressions can determine the longitudinal feed rate in
"Through Feed Centreless Grinding"?
(If the diameter of the regulating wheel = D, r.p.m. of the regulating wheel = N, angle of
inclination of the regulating wheel = 0)
Ans 1. Longitudinal feed rate =lxDxNx Sin (0)
X2. Longitudinal feed rate = [l x Dx NJ / Sin (0)
X3. Longitudinal feed rate = I1 x D xNx Cos (0)
X 4. Longitudinal feed rate =[MxD x N]/Cos (0)
<br>
Q.60 Which of the following wheels supports the workpiece in internal centreless grinding
operation?
Ans 1. Pressure roller, supporting roller and regulating wheel
X 2. Only pressure roller
X 3. Only supporting roller
X
4. Only regulating wheel
<br>
Q.80 Which of the following is the correct sequence for the IS specification of any Grinding
wheel?
- - - -
Ans X1.Abrasive used Structure Grade Grit number Bond Type
X 2. Abrasive used - Grit number - Structure - Grade - Bond Type
3. Abrasive used -Grit number - Grade - Structure - Bond Type
X 4.Abrasive used - Grade - Structure - Grit number - Bond Type
<br>
Q.88 Which of the following is the correct rule when selecting a Grinding Wheel?
Ans X 1. Close structure for ductile and soft material
2. Soft wheel for hard metal and hard wheel for soft metal
X 3. Hard wheel for hard metal and soft wheel for soft metal
X4. Fine finish needs open structure
<br>
Q.90 Which of the following is the primary element that supports the workpiece in centreless
grinding?
Ans 1. Work rest blade
X2. Stationary table
X3. Work test blade
X4. Pressure roller blade
<br>
Q.8 Which of the following centre-less grinding can be preferred for headed, stepped, or
taper-shaped workpieces?
Ans 1. Plunge cut grinding
X 2. Taper out grinding
X3. Rotation feed center-less grinding
X 4. Out feed grinding
<br>
Q.30 rack and pinion gear, the rack is a
In and the pinion is a
Ans X 1. straight line gear; straight line gear
2. straight line gear; circular wheel
X 3. circular wheel; straight line gear
X4. circular wheel; circular wheel
Which of the following elements provides the necessary horizontal force to the
<br>
Q.48
workpiece in centerless grinding?
Ans 1. Regulating wheel
X 2. Stationary wheel
X
3. Work test blade
X 4. Revolving wheel
<br>
Q.59 What is the full form of CBN', which is used as an abrasive in grinding processes?
Ans X1. Calcium bi nitrous
X2. Carbon boron nitrate
K 3. Copper boron nitride
4. Cubic boron nitride
<br>
Q.87 Which of the following is the surface coating process?
Ans X1. Tumbling
X 2. Hot doping
3. Hot dipping
X 4. Pickling
<br>
Q.1 Which of the following is NOT a mechanical finishing process?
Ans X1. Burnishing
2. Pickling
X3. Shot peening
X 4. Buffing
<br>
Q.2 Which of the following is used in organic coating as catalysts that speed up the cure
reaction?
Ans X1. Colloidal stabilisers
X 2. UV stabilisers
X3. Plasticisers
4. Cure additives
<br>
Q.10 What is the basic essential condition for coating material in hot dipping?
Ans X1.It should have a higher melting point than the base metal.
2. It should form an alloy at the interface with the
base metal.
X 3. It should completely evaporate during the process.
X4. It should have lower wettability.
<br>
Q.26 Electroplating is the opposite of which of the following?
Ans X1. Electrolysis
X 2. Battery charging
3. Galvanic cell
X 4. Fuel cell
Which of the following processes produces the minimum surface roughness on
<br>
Q.90
workpieces?
Ans X1. Honing
2. Superfinishing
X 3. Grinding
X 4. Lapping
<br>
Q.12 Which type of light is generally used in the photo etching process?
Ans X 1. Infrared (IR) light
X 2. X-ray
X 3. Visible light
4. Ultraviolet (UV) light
Which of the followingare used to improve pigment dispersion and the stability of
<br>
Q.3
coatings during organic coating?
Ans 1.Colloidal stabilisers
X 2. Pigment analyser
X 3. Curing stabilisers
X 4. Plasticisers
