Fosroc Renderoc SP40 constructive solutions

Shrinkage controlled, polymer modified, cementitious Properties

repair mortar, specifically designed for spraying
The following typical results were obtained at a water:powder
Uses ratio of 0.18.
Renderoc SP40 is suitable for wet spraying and hand Test method Typical result
application in a wide variety of repair applications, and is
Drying shrinkage to ASTM C 157-93
particularly well suited to vertical and overhead repairs. 28 days : <1000 microstrain
Typical applications would include, but not be limited to, the
following: 2
Flexural strength : >7 N/mm at 28 days
Mass infill to large areas (BS 6319 Pt.3)
2
Tensile strength : >2.5 N/mm at 28 days
Repairs to irregular profiles (BS 6319 Pt.7)
Excellent for repairs to fire-damaged concrete

Fast track repair programmes, where rapid application at Compressive strength : >20 Mpa at 1 day
high volume is required hand application
1
Single layer, high build applications (BS 1881 Pt.116 ) >45 Mpa at 28 days
(iterative result, based upon
spray application)
Advantages
Note 1: 70mm cubes, air cured @ 25°C.
Cost effective - shrinkage control enables repairs to be
completed „right first time‟. Very low rebound is an Design criteria
additional cost benefit
Attention to the basic design criteria given below should
Enhanced durability - works in tandem with extremely
ensure that the full benefits of this technology are achieved :
low permeability to prolong effective working life
(i) Recommended limits for a single spray application
Compatibility - aligns performance closer than ever are:
before, to that of host concrete
Minimum applied thickness : 40 mm
User friendly - specifically developed to provide an easy- Overhead sections : up to 150 mm thick
to-apply product, suitable for local conditions Vertical sections : up to 200 mm thick
Definable performance - positive benefits are easily Surface area of a single repair : see „Note‟

demonstrated via a single, simple measurement NOTE : The restricting factor on surface area will be the
practicality of maintaining a continuous
Description application
Renderoc SP40 is supplied as a ready to use blend of dry ii) In situations where a substrate/repair barrier is required,
powders, which requires only the addition of clean water to or enhanced bond strength/working time is required, or
produce a highly consistent, hand and spray grade, repair where the substrate is likely to be damp (e.g. seawalls,
mortar suitable for most structural and load bearing repairs. quays etc.), Nitobond EP epoxy bonding agent should be
used.
Technical support
(iii) Water addition - between 4.25 & 4.5 litres per 25 kg bag
Fosroc offers a comprehensive technical support service Under no circumstances should part bags be used or
to specifiers end users and contractors. Fosroc is also able additional water be employed. Either of these two actions
to offer on-site technical assistance, an AutoCAD facility will adversely affect material performance, automatically
and dedicted specification assistance in locations all invalidating Fosroc‟s standard product guarantee.
over the world.
Instructions for use
Renderoc SP40

Renderoc SP40 should be mixed and applied in strict

accordance with the Product Method Statement, a copy of
which may be obtained from your nearest Fosroc office.
Fosroc Renderoc SP40

Estimating
Precautions
Supply
Health and safety
Renderoc SP40 : 25 kg bags
Renderoc SP40 contains cement powders which, when
Yield mixed with water or upon becoming damp, release alkalis
Renderoc SP40 : approx 13.5 litres which can be harmful to the skin.
(at water addition of 4.25ltr/bag) per 25kg bag During use, avoid inhalation of the dust and contact with the
skin or eyes. Wear suitable protective clothing - eye
Limitations
protection, gloves and respiratory equipment (particularly in
Renderoc SP40 should not be used when the ambient
confined spaces).
temperature is below 5°C and falling.
The use of barrier creams to provide additional skin
Renderoc SP40 should not be part mixed, nor part bags
protection is also advised. In case of contact with the skin,
used.
rinse with plenty of clean water, then cleanse thoroughly with
Renderoc SP40 should not be exposed to running water
soap and water.
either during application or prior to final set.
In case of contact with eyes, rinse immediately with plenty of
Storage
clean water and seek medical advice. If swallowed seek
Shelf life medical attention immediately - do not induce vomiting.
Fire
Renderoc SP40 has a shelf life of 12 months if kept in a
dry environment, in its original packing. If stored in Renderoc SP40, is non-flammable and thus presents no fire
conditions of high temperature and/or humidity, the shelf hazard.
life may be reduced to as little as 4 months
For further information, please refer to the Product Material
Safety Data Sheet for Renderoc SP40.

* Denotes the trademark of Fosroc International Limited

†
See separate data sheet

Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. W hilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
Fosroc Chemicals
continuous control over where or how its products are applied, accept any liability either
directly or indirectly arising from the use of its products whether or not in accordance with
(India) Pvt. Ltd. any advice, specification, recommendation or information given by it.
Head Office
“Sapthagiri Palace”, No.38, telephone fax e- m ail
II & III Floor, 12th Cross, ++91 80-23551500 ++91 80-23551510 enquiryindia@fos roc.c om
CBI Road, Ganganagar North,
Bangalore 560 032
Regional Office

Bangalore Mumbai Noida Kolkata

“Sapthagiri Palace”, No. 38 1401/1402, 14 Floor, D-166 Sector 10 304, Jodhpur Park
II & III Floor, 12th Cross, A-W ing‟The Great Eastern Summit‟ Noida, Kolkata 700 068
CBI Road, Ganganagar North, Sector-15, CBD, Belapur UP 201 301 Ph:033-65343188
Bangalore 560 032. Navi Mumbai 400 614 Ph:0120-4270620 Fax: 033-2499-0280
Ph:080-23551500 Ph: 022 -43406800-04
Fax : 080-23551510

www.fosroc.com
www.fosroc.com