Water Filtration Device CHP-7310R

• This product can not be used if the voltage is different from that mentioned in the rating plate.
• For your safety and proper use of the product, please read this User’s Manual before use.
FEATURES

Hot water temperature control capability

1 You can select the temperature for hot water through the multi-level
hot water temperature dial according to purpose of use.

Precise extraction capability

2  ou can extract the precise amount of water according to purpose of use

Y
through the cold/hot/ambient water precision extraction function.

Hygiene improvement for water purifier through

3
utilization of UV LED technology
 V LED is activated when extracting cold/ambient water to improve
U
hygiene within faucet.

Application of high capacity tank

4 You can extract even more water with the larger high capacity tank.

Power saving mode through light detecting sensor

5  ou can save power with the power saving mode configuration to automatically
Y
reduce the operation of LED indicators and heater throughout the night.
DEAR CUSTOMERS

COWAY
Thank you for using Coway water filtration device.
Please read this User Manual to learn about proper usage and maintenance of the product.
When a problem occurs while using the product, it can be solved by referring to the instructions in this manual.

FEATURES / CONTENTS
CONTENTS

Product Information How to Use

| 03 | Safety Information | 09 | Please Check Before Use

| 07 | Parts Name | 10 | Buttons and Indicators
| 08 | Water Filtration Process | 18 | How to Get the Desired Water
How to Get Cold Water
How to Get Ambient Water
How to Get Hot Water
How to Get Warm water

Maintenance Others

| 20 | How to Install | 29 | Troubleshooting

| 22 | How to Clean | 31 | Product Specifications
How to Clean the Internal Water Tank | 32 | Water Flow Diagram
How to Clean the Tray | 33 | PERFORMANCE DATA SHEET
| 26 | Filter Replacement
| 27 | How to Replace the Filter

- Please keep the user manual in easily accessible areas. - 2

SAFETY INFORMATION

Please follow all instructions for your safety!

These instructions are for keeping you safe and to prevent property damage.
Please use the product correctly after reading the precaution.

When mortality or fatal injury When severe bodily harm or When minor bodily harm or
is predicted for not following property damage is predicted property damage is predicted
instruction for not following instruction for not following instruction
Danger Warning Caution

Regarding Power Supply

D
 o not use damaged power plug or loose fitting outlet.
There is risk of electrocution and fire.

Do not pull on the power cord.

There is risk of electrocution and fire.

Do not pull on the power cord to move the product.

There is risk of electrocution and fire.

Do not touch the power plug with wet hand.

There is risk of electrocution and fire.

Do not bend the power cord excessively or press it with a heavy object.
There is risk of electrocution and fire.

Do not plug and unplug the power plug repetitively.

There is risk of electrocution and fire.

 hen the power supply comes in contact with water, unplug the power plug
W
and completely dry it prior to use.
There is risk of electrocution and fire.

Y
 ou must disconnect the power plug for product repair, inspection, or component
replacement.
There is risk of electrocution and fire.
 Product Information
 lease disconnect power, wipe clean, and dry prior to use when there is dust,
P
water, etc. present on the pin and connector of the power plug.
There is risk of electrocution and fire.

 o not connect multiple products to one power outlet. Always use a separate
D
socket for the product.
There is risk of fire.

L ock the tap water valve and disconnect power when not using the product

SAFETY INFORMATION
for an extended period of time.
There is risk of electrocution and fire.

Do not modify the power cord arbitrarily.

There is risk of electrocution and fire.

 o not arbitrarily replace the damaged power cord and contact the service
D
center to replace the power cord.
There is risk of electrocution and fire.

Regarding Installation

Do not install near electric heating device.

There is risk of fire.

 o not install it in a location with too much humidity or dust or in a location

D
that is exposed to water or rain.
There is risk of electrocution and fire.

Do not store or use flammable gases or materials near the product.
There is risk of electrocution and fire.

Do not install it on a tilted surface.

There is risk of bodily harm and product damage.

I nstall it in a location that is at least 2m away from electronic appliances such

as an induction range and an electronic pressurized rice cooker.
3
Otherwise, electromagnetic interference may occur.
4
SAFETY INFORMATION

When mortality or fatal injury When severe bodily harm or When minor bodily harm or
is predicted for not following property damage is predicted property damage is predicted
instruction for not following instruction for not following instruction
Danger Warning Caution

During Use

 lease lock the tap water valve and disconnect the power plug and contact
P
the service center if there is water leak from inside the product or if water is
puddling around the product.
There is risk of electrocution.

I mmediately disconnect the power plug and contact the service center if there
is any burning smell or smoke or strange noise from the product.
There is risk of electrocution and fire.

Do not place candles or cigarettes on top of the product.

There is risk of fire.

 o not place bowl filled with water, chemicals, food, small metals, or flammable
D
substances on top of the product.
There is risk of electrocution, fire, and product damage if product is exposed to them.

 lease be careful not to come in direct contact with hot water and warm water
P
as they are hot.
There is risk of burns.

Use after completely closing the water tank cover inside the product.
Bugs and debris may enter the product.

P
 lease replace the filter according to the filter replacement cycle to drink clean water.
Using expired filter decreases water purification performance.

 ompletely drain the stored water as well as newly filtered water one more
C
time prior to use when using the product after an extended period of time.
The stored water may be contaminated.
 Product Information
Others

Disconnect the power plug prior to cleaning.

There is risk of electrocution and fire.

 o not directly spray water on product for cleaning or use benzene or thinner
D
to wipe the product.
There is risk of electrocution and fire.

SAFETY INFORMATION
Do not arbitrarily open, repair, or remodel the product.
There is risk of electrocution and product damage.

Do not use the filtered water for replacing water in fish tanks and aquariums.
Water filtered through membrane does not contain ion substances which may be inappropriate for
living environment of fish. There is risk of fish mortality depending on the circumstances.

T here may be residual fine black powder at the bottom of the internal water
tank after moving the product or replacing the Plus Inno-sense filter.
This is fine powder from the activated carbon used in the Plus Inno-sense filter for better taste in
filtered water which is harmless to human body.

D
 o not rotate or lift the product by grabbing on to the filtered water extraction valve.
This causes water leak and product damage.

6
PARTS NAME

Front

Display unit

Faucet

Tray

Back

Back cover

Condenser

Power cord

Residential water output hose

(Blue)
Tap water input hose (Orange)

Connector for cooking water

Accessory
Water
Before Filtration
•• Warrantyoperating
card the
unit,
is included
Device
please
in this read CHP-731
user’s this manual
manual. 0R
thoroughly,
and
retain
it for
future
reference.

User Manual Drain hose Antibacterial filter

WATER FILTRATION PROCESS

Product Information
The essence of the water filtration system lies in the filters.
Using a filter that is not certified or even using a certified filter for too long may reduce the filter performance.

5-step Water Filtration System (CHP-7310R)

Step 1, 2 : Neo-Sense filter

This neo-sense filter has the function of removing particulates, dissolved organic and inorganic impurities.

PARTS NAME / WATER FILTRATION PROCESS

It also has another function to remove chlorine, volatile organic compounds(VOC’s).

Step 3 : Membrane filter (RO)

RO Membrane filter has a function to remove water contaminants such as heavy metals, waterborne
microorganisms and harmful organic chemicals etc.
This water which contains harmful material is eliminated through the reject water hose as disposed water.

Step 4 : Plus Inno-Sense filter

This Plus Inno-Sense filter has functions to remove smell inducing material and to improve taste of water.

Step 5 : Antibacterial filter

This Antibacterial filter has function to control microorganism propagation in water.

Anti-
bacterial
filter

Reject water
Outlet

Neo-Sense Membrane filter Plus Inno-Sense filter Antibacterial

filter (RO) filter

► Uses of the disposed water

- The disposed water should be used only for cleaning house, cloths,
Tips or purposes other than drinking.
- Never use the disposed water for drinking or for cooking. 7

8
PLEASE CHECK BEFORE USE

Please Check Before Use!

This product is for 220V - 240 V~, 50 Hz .

Please connect the power plug to grounded 220 V - 240 V~, 50 Hz outlet.
The water filtration device requires power supply to operate.

■ Open the tap water valve. ■ Regular filter replacement

Tap water must be supplied for operation. Regular filter replacement is crucial for drinking
clean water. Using expired filter decreases water
filtration device performance so please replace
the filter on time.

■ When indicator is turned off on ■ Hot water dispensing instructions

display unit Loosen the two screws by the door on the side to
Please check for power failure or power stoppage open the door and open the red cap, connect the
for other various reasons when indicators of the dispensing hose (Continued extraction hose) to
display unit are turned off. dispense the hot water inside the water tank.
(Please be careful to not get burned when
dispensing hot or warm water.)

■ When using after extended period ■ Instructions for dispensing filtered

of time water during power failure
Completely drain the stored water as well as Open the blue cap and connect the dispensing
newly filtered water one more time prior to use hose(Continued extraction hose) to dispense
when using the product after an extended period some of the filtered water. Use during power
of time. failure and do not use to dispense hot water.

■ After installing product

Fill up the tank and drain it completely twice or
more before use.

- Lock the tap water valve and disconnect power when not using the product for an
extended period of time.
Tips
BUTTONS AND INDICATORS

How to Use
Hot Water Indication Part

1 User mode indicator

 ot water purpose indicator
2 H  xtraction amount
3 E
by temperature indicator
 ot water temperature
4 H
indicator  xtraction amount
6 E
indicator
5 Temperature indicator

PLEASE CHECK BEFORE USE / BUTTONS AND INDICATORS

1 User mode indicator 2 Hot water purpose indicator
It activates the selected user indicator by temperature
during user mode.
It activates of purpose indicator by
appropriate temperature.
It turns on ideal hot water temperature as an icon
(Baby milk, baking, tea, coffee, ramen) by temperature.

3 Extraction amount indicator 4 Hot water temperature indicator

Hot water extraction amount is displayed Indicator turns on by temperature of
with image and number. hot water.
7 Stages(250 ml → 350 ml → 500 ml → 750 ml 6 Levels of hot water temperature are
→ 1 000 ml → 1 500 ml → continuous extraction(CON)) displayed in total.
Displays temperature of hot water. (40 ° → 50 ° → 60 ° → 70 ° → 80 ° → 90 °)

5 Temperature indicator 6 Extraction amount indicator

Indicator turns on once hot water is Indicator turns on once extraction
selected. amount of hot water is selected.

10
BUTTONS AND INDICATORS

Hot Water Indication Part

11 L ow hot water
indicator

7 Hot water status indicator 8 Hot water indicator

9 Child lock indicator

 ot water extraction
10 H
indicator

7 Hot water status indicator 8 Hot water indicator

Indicator turns on according to Indicator turns on once hot water is
temperature of hot water. selected.
More lights on display indicates hotter temperature.

9 Child lock indicator 10 Hot water extraction indicator

Indicator turns on once child lock Indicator turns on once hot water is
function is selected. extracted.

11 Low hot water indicator

Indicator is turned on when the water
level of the hot water tank is below low level.
 How to Use
Indication Part

12 L ow water level
indicator
 ater filtration
13 W
function indicator 18 Light detection
sensor
 old water function
14 C
indicator

BUTTONS AND INDICATORS

 old water status
15 C
indicator
 xtraction amount
16 E 19 F unction ON/
indicator OFF indicator

17 Extraction indicator

12 Low water level indicator 13 Water filtration function

Indicator is turned on when the water indicator
level of the internal tank is below low Indicator is turned on once water filtration
water level. function is selected.

14 Cold water function indicator 15 Cold water status indicator

Indicator is turned on once cold water Indicator turns on according to
function is selected. temperature of cold water.
 ore lights on display indicates cooler
M
temperature.

16 Extraction amount indicator 17 Extraction indicator

Selected extraction amount is displayed. It turns on when filtered water/cold water
(250 ml, 500 ml, 1 000 ml, continuous is being extracted.
extraction)

18 Light detection sensor 19 Function ON/OFF indicator

It is a sensor that detects luminosity. ECO mode, cold water, hot water,
On/Offs are, displayed.

11

12
BUTTONS AND INDICATORS

Hot Water Control Part

1 User button

2 Hot water button

3 H
 ot water temperature
/Extraction control dial

4 Child lock button

5 H
 ot water extraction
button

1 User button 2 Hot water button

User’s water consumption pattern is Use when you wish to extract hot water.
remembered.

3  ot water temperature/
H 4 Child lock button
Extraction control dial Use when you wish to select child lock
Use when you wish to control hot water function. Press for about 3 seconds to turn
temperature/extraction amount. on/off child lock mode.
Turn dial to the left to select lower (Hot water/Extraction is disabled in child
temperature/lesser extraction amountand lock mode.)
turn dial to the right to select higher
temperature/higher extraction amount.

5 Hot water extraction button

Use when you wish to extract hot water.
 How to Use
Control Part

6 Water filtration
button

7 Cold water button

BUTTONS AND INDICATORS

10 Function ON/
OFF button
8 Extraction amount
button

9 Extraction button

6 Water filtration button 7 Cold water button

Use when yoau wish to extract filtered Use when you wish to extract cold water.
water.

8 Extraction amount button 9 Extraction button

Use when you wish to select desired Use when you wish to extract filtered
extraction amount. water/cold water.
* Continuous extraction lasts for 3 minutes.

10 Function ON/OFF button

Use when selecting ECO mode, cold water
on/off, hot water on/off functions.

13

14
BUTTONS AND INDICATORS

■ Using hot water function

Press hot water button and check that the hot water function
indicators are turned on the display unit.
∗ You can drink hot water about 30 minutes after turning on hot water function.

- Configuring temperature for hot water

Press hot water button and turn the dial once the temperature selection indicator blinks on the display unit to
select temperature. Hot water temperature can be controlled in 6 levels(40 °→50 °→60 °→70 °→80 °→90 °) and
turning the dial to the right increases the temperature and turning the dial to the left decreases the temperature.

∗ 6 Levels of temperature for hot water

- Configuring extraction amount for hot water

Press hot water button and turn the dial once the hot water extraction amount indicator blinks to select
extraction amount of hot water. Hot water extraction amount can be controlled in 7 levels(250 ml → 350 ml
→ 500 ml → 750 ml → 1 000 ml → 1 500 ml → Continued extraction(CON)) and turning the dial to the right
increases extraction amount and turning the dial to the left decreases extraction amount.

∗ 7 Levels of extraction amount

 How to Use
■ Hot water memory function
This function allows you to set frequently used hot water temperature and amount using the memory
function for up to 3 memories.
After that, you only need to press a button to extract the hot water.

- Configuring temperature for hot water

1. Select one from Memory A, B, and C. The hot water temperature and amount stored in
the memory are displayed.

BUTTONS AND INDICATORS

∗If there is no button input for a certain duration, the mode changes to the ambient water mode.
2. When hot water temperature indicator is turned on, turn the dial to select the temperature you want.
3. Press hot water button. When extraction amount indicator is displayed, turn the dial again to set the
extraction amount you want.
4. Press and hold the memory button you want. The memory indicator blinks a few times and the hot
water temperature and amount you set are saved in the memory.
∗ The default settings for the memory are 90 °C, 250 ml.

▶ ▶ ▶

- Extracting hot water

1. S elect one from memory A, B, and C. Hot water temperature and amount stored in the memory are displayed.
∗ If there is no button input for a certain duration, the mode changes to the ambient water mode.
2. Press the extraction button to extract the water according to the hot water temperature and amount
you set in the memory.

15

16
BUTTONS AND INDICATORS

■ Using cold water function

Press cold water button and check that the cold water function indicators
are turned on the display unit. Press COLD ON/OFF button
of the product for a few seconds to turn off cold water function.

■ Using filtered water function

Press water filtration button and check that the water filtration function
indicators are turned on the display unit.

■ Using power saving mode

Pressing power saving mode button will turn on power saving mode
indicator and the compressor operation will decrease throughout the night
to reduce power consumption.
∗ Cold water is less cold and hot water is less hot during power saving mode.
HOW TO GET THE DESIRED WATER

How to Use
How to Get Cold Water

Press cold water button, then press the

extraction button.

BUTTONS AND INDICATORS / HOW TO GET THE DESIRED WATER

▶ ▶

- If cold water is not being dispensed, please check that cold water indicator is turned on the
display unit (Refer to P.13)
Tips

How to Get Ambient Water

Press water filtration button, then press the

extraction button.

▶ ▶

17

18
HOW TO GET THE DESIRED WATER

How to Get Hot Water

Press hot water button and then press extraction button

once temperature selection indicator on the display unit blinks.

▶ ▶

- If hot water is not being dispensed, please press HOT ON/OFF button at the bottom of the
product to check that the indicator is on.
Tips - Please be careful of burns when using hot water.

How to Get Warm Water

Press hot water button and turn the dial to select the temperature of warm water once temperature
selection indicator on the display unit blinks,
then press extraction button.

▶ ▶

- Warm water is a function that mixes certain amount of hot water and cold water.
This product has been configured to produce warm water when the indicators of hot water and cold
water temperature are turned on to the maximum level.
Therefore, the water may be hotter or colder than usual if temperatures of hot and cold water are not equivalent.
Tips
Also, the water may be hotter than usual when low water level indicator is on.
- Please be careful of burns when using warm water as it may be hot.
HOW TO INSTALL

Maintenance
Installation Guide

Tap water valve

HOW TO GET THE DESIRED WATER / HOW TO INSTALL

For own dedicated
220 V - 240 V~, 50 Hz
AC only electric outlet

Cooking water
connection

Connect the orange tap water input hose to 1 the water pipe.
Connect 2 the wasted water output hose.

Tap water input hose (Orange) connection

1
Residential water output hose(Blue) connection
Cooking water connection
3 2
19

20
HOW TO INSTALL

Be Careful!

■ Where to install the water ■ Water filtration installation

filtration unit I location II
Install the product in a cool part of the Allow a clearance of 10 cm or more behind the
room, on an even surface, out of direct product, and level the water filtration unit.
sunlight and away from humidity, dust, and
dripping water.

■ After installing the water ■ Relocation and installation

filtration unit If the unit is relocated, do not plug in the
Filter the water for more than 50 minutes or power cord until 30 minutes after the unit
fill and drain once before using the unit. has been installed.
(Drain the filtered water more than twice.)

■ Cold water tubing

Make sure the unit is connected to the cold
water supply line.
(If connected to the hot water supply line,
the filtration unit may be damaged.)

S ome residual water used in the product inspection may be present within the filter.
Do not be alarmed as it is not a used product.
Tips Do not reuse the tap water valve and hose used before the product installation.
HOW TO CLEAN

Maintenance
How to Clean the Internal Water Tank

1. P
 ress COLD ON/OFF and HOT ON/OFF buttons at the bottom of the product to turn off the LED.
Please lock the tap water valve.

▶ ▶

HOW TO INSTALL / HOW TO CLEAN

2. Press cold water button (1), continuous extraction amount button (2), and extraction
button(3) to completely discharge the water inside the water filtration device through
the draining hose.

3. Disconnect the power plug.

21

22
HOW TO CLEAN

4. Use a screw driver (+) to loosen the two screws on the door side cover and discharge through
the hot water discharge pipe (RED).

▶ ▶

5. Push upper cover of the product to open, open the fixture clips(6) on the internal water tank,
and lift up the internal water tank cover to open.

▶ ▶

6. Rotate antibacterial filter on the internal water tank cover to remove it and wash using
prepared water.

7. Wipe the surface of the internal water tank with soft cloth.
 Maintenance
8. Use prepared water to wash out the internal water tank and connect the power plug.
Use the discharge hose to completely discharge all water as well as initially filtered water before use.

▶ ▶

HOW TO CLEAN
9. Rotate antibacterial filter into the internal water tank cover, close the internal water tank cover,
and close fixture clips(6) of the internal water tank.

10. Close the door side cover of the upper cover, and open the tap water valve.
Check that water is being dispensed from the cold water/filtered water and hot water extraction
faucets and press the COLD ON/OFF and HOT ON/OFF buttons at the bottom of the product to turn
on the LED. Press the cold water button to reactivate the water filtration device.

23

24
HOW TO CLEAN

How to Clean the Tray

1. Instructions for the tray Disassembly

Pull on the front of the tray for easy disassembly.

2. Instructions for the tray assembly

Attach the tray hook to product and push gently.

Please shut the internal water tank cover completely.

Bugs and debris may enter the product.

Do not use chemicals or detergents when cleaning internal water tank.
Tips Residual chemicals and detergents may be harmful to the body.
- Please maintain a clean surrounding and clean the internal water tank once every two months.
FILTER REPLACEMENT

Maintenance
 Filter Replacement Cycle
If the filter is not regularly replaced, it may degrade the water quality from the product.
The filter change cycle may vary within the range of expected replacement cycle depending on the feed water quality.

The period for filter change is calculated based on 10 L water usage per day for
Tips a household of 4 members.

CHP-7310R

HOW TO CLEAN / FILTER REPLACEMENT

Expected Replacement Cycle
Filter Name
Reverse Osmosis
Neo sense filter 6 months
Membrane filter (RO) 24 months
Plus Inno-sense filter 18 months
Antibacterial filter 12 months

25

26
HOW TO REPLACE THE FILTER

Replace the Filter!

1. Disconnect the power plug, lock the tap water valve, and discharge all water inside the
water filtration device. (Refer to P.21)

▶ ▶

2. Use a screw driver (+) to loosen the two screws on the door side cover.

▶ ▶

3. P
 lease disconnect the fitting connected to the filter
you wish to replace and replace the filter.
(Use appropriate tool to disconnect the fitting.)

 fter replacing the filter, connect the fitting and the hose accurately to ensure
A
Tips that there is no leak and dispose the initially filtered water.
 Maintenance
4. Please tighten the two separated door side screws and close. Connect the power plug.

HOW TO REPLACE THE FILTER

▶

Please be sure to use the new filter after cleansing.

- Neo-sense filter : Please assemble after cleansing with Neo-sense filter for
about 1 minute.
- Membrane filter (RO) : After cleansing with the main water passed
Tips Neo- sense filter for about 5 minutes, please assemble it.
- Plus Inno-sense filter : Please use the filter without flushing.
- Antibacterial filter : Please use the filter without flushing.

27

28
TROUBLESHOOTING

The water filtration device may operate abnormally due to minor causes not because of the product
malfunction but because of the fact that the user is not familiar with the product use. In such a case,
problems can be solved easily even without the help from the Service Center by checking the following
tems. If you can’t solve the problem after checking the following items, please call the Service Center.

Symptom Check Measures to take

• Did you clean the internal water tank? Please clean the internal water tank.

• I haven’t used the water filtration device for Please dispose the stored water and clean the
Water tastes weird.
a very long time. internal water tank.

• Isn’t it time for filter replacement? Please request for filter replacement.

• Is the device disconnected from the water

Please open the tap water valve.
Water is not being supply or is the tap water valve locked?
dispensed.
• Did you miss the filter replacement period? Please request for filter replacement.

• Isn’t it time for filter replacement? Please request for filter replacement.

Please check that the power cord is connected

The filtration amount • Is the power connected?
to 220 V - 240 V~, 50 Hz outlet.
has suddenly
decreased. • Is the tap water valve locked? Please open the tap water valve.

• Is the temperature of tap water declining Filtration amount decreases as water
rapidly? temperature decreases.

• Is cold water indicator on? Please press the cold water button.

Water cooling function is not activated

Cold water is not • Is the tap water valve locked? when water level is low to protect the motor.
being dispensed. Please open the tap water valve.

• Is the water filtration device too close to Please maintain distance of at least 10cm
the wall? from the wall.

• Is hot water indicator on? Please press the hot water button.

The water may be less hot in power saving

• Is the power saving mode indicator turned on?
mode.

Heater function does not activate when water

Hot water is not
• Is the tap water valve locked? level is low to prevent overheating of the
being dispensed. heater. Please open the tap water valve.

Warm water is dispensed if the hot water-warm

• Is the hot water-warm water temperature water temperature control dial is turned to
control dial turned to warm water? warm water. Turn the control dial all the way to
the right.
 Symptom Check Measures to take

Others
Please press the hot/cold water button to turn on
hot/cold water function. Temperature of warm
• Is the hot water or cold water indicator turned on?
water may vary depending on temperature of
hot/cold water.

The water may be hotter or colder than usual

Warm water is not • Is the low water level indicator turned on? when low water level indicator is on. Please
check again after low water level indicator is off.
being dispensed.
The water may be less hot than usual when
• Is the power saving mode indicator turned on ?
power saving mode is on.

TROUBLESHOOTING
Heater function does not activate when water
• Is the tap water valve locked? level is low to prevent overheating of the heater.
Please open the tap water valve.

• Is the water supply intact? Please check the tap water valve.
The device stopped
Please check that the power cord is connected to
suddenly during • Is the power connected?
220 V - 240 V~, 50 Hz outlet.
operation.
• Is there leak or flooding of filtered water? Please request for repair service.

29

30
PRODUCT SPECIFICATIONS

Product Name Coway Water Filtration Device

Mode CHP-7310R

Filtration Method Reverse osmosis type

Standard Power Voltage 220 V - 240 V~, 50 ㎐

Rated Power Input Cool : 0.6 A, Heat : 800 W

Cold water temperature, (Warm)Hot water temperature, (Warm)Hot water extraction

Display Unit Details amount selection, Filtered/Cold water extraction selection, Power saving mode, Low
water indicator, Mode light indicator, Cold water function, Hot water function

Water filtration,. Cold water, Hot water, Overheating prevention, Subcooling prevention,
Major Features
Extraction faucet sterilization

Ambient water 7.8 L

Water
Cold water 2.3 L
tank
Hot water 3.4 L
Capacity
Total 13.5 L

Neo-sense filter Activated carbon block

Filter Membrane filter (RO) Reverse osmosis

Material Plus Inno-sense filter Activated carbon block, non-woven fabric

Antibacterial filter Ceramic filter

Size (W × D × H) 340 mm (width) × 523 mm (depth) × 518 mm (height)

Water Temperature 5 °C - 35 °C

Working Temperature 5 °C - 35 °C

Working Pressure 0.07 MPa – 0.83 MPa

Weight 21.9 kg

▶ Amount of filtered water may vary depending on water pressure and temperature.
▶W
 ater tank capacity reflects the size of the water tank, and may be different from what is dispensed
from the filtration unit.
▶ F or product improvement purposes, product specifications are subject to slight changes
without prior notice.
MALAYSIA

Add: C
 OWAY (M) SDN. BHD
Level 20, Ilham Tower, No. 8, Jalan Binjai,
50450 Kuala Lumpur.
Careline : 1800-888-111
WATER FLOW DIAGRAM

Others
CHP-7310R
Water Level Sensor
(Flood/High/Medium/Low)
Booster Pump

Filter
Antibacterial
Ambient Water
Ambient Water Extraction Valve
7.8 L
Water Source Input
Cold Water Ambient Water/
Extraction Valve Cold Water Extraction
Flow
Sensor
Cold Water
2.3 L
Hot Water
3.4 L Disk Valve
FEED/NOS
Valve
Hot Water Extraction

PRODUCT SPECIFICATIONS / WATER FLOW DIAGRAM

Temperature Sensor Hot Water
(Warm water) Extraction Valve

Residential Water
Control Valve

Neo-Sense Filter Membrane Filter Plus Inno-Sense Filter

(RO)

Mineral Filter

Extraction Drain For Hot Water Drain

Cooking Water Power Failure (Color of cap: RED)
Optional (Color of cap: BLUE)

Residential Water & Drainage

31

32
 Water Filtration System Performance Data Sheet

Model: CHP-7310R
This system has been tested and certified by the Water Quality Association according to NSF/ANSI 42, 53, 58,
and 401 for the reduction of the substances listed below. The concentration of the indicated substances in water
entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the
system, as specified in NSF/ANSI 42, 53, 58, and 401.
Maximum Allowable Product Water
Influent Challenge Concentration Percent Reduction
Substance Concentration
(mg/L unless specified) (%)
(mg/L unless specified)
Arsenic (Pentavalent) 0.050 ± 10% 0.01 97.8
Barium 10.0 ± 10% 2 97.2
Cadmium 0.03 ± 10% 0.005 98.2
Chromium (Hexavalent) 0.3 ± 10% 0.1 98.6
Chromium (Trivalent) 0.3 ± 10% 0.1 99.4
Copper 3.0 ± 10% 1.3 98.1
Lead 0.15 ± 10% 0.01 99.1
Selenium 0.10 ± 10% 0.05 98.3
TDS 750 ± 40 187 95.3
Aesthetic Chlorine 2.0 ± 10% ≥ 50% Reduction 79.2
VOC* 0.300 ± 10% ≥ 95% Reduction 99.7
Meprobamate** 0.0004 ± 20 % 0.00006 95.1
Phenytoin** 0.0002 ± 20 % 0.00003 96.5
Atenolol** 0.0002 ± 20 % 0.00003 95
Carbamazepine** 0.0014 ± 20 % 0.0002 98.8
TCEP** 0.005 ± 20 % 0.0007 97.9
TCPP** 0.005 ± 20 % 0.0007 97.8
DEET** 0.0014 ± 20 % 0.0002 98.7
Metolachlor** 0.0014 ± 20 % 0.0002 98.7
Trimethoprim** 0.00014 ± 20 % 0.00002 96.8
Ibuprofen** 0.0004 ± 40 % 0.00006 96.2
Naproxen** 0.00014 ± 20 % 0.00002 97.5
Estrone** 0.00014 ± 20 % 0.00002 96.8
Bisphenol A** 0.002 ± 20 % 0.0003 99.4
Linuron** 0.00014 ± 20 % 0.00002 96.6
Nonyl phenol** 0.0014 ± 20 % 0.0002 97.8
**Reduction of substance certified according to NSF/ANSI 401.
While testing was performed under laboratory conditions, actual performance may vary.
General Operating Information:
Daily production Rate 40.2 GPD
180 gallons (for VOC, reduction of substances certified to NSF/ANSI 401)
Rated Capacity
3 000 gallons (for Aesthetic Chlorine)
Min-Max operating pressure: 10 ~ 120 psi (0.07MPa- 0.83 MPa)
Min-Max operating temperature: 41 °F ~ 95 °F (5 °C ~ 35 °C)
Rated Service Flow 0.07 gpm
Electrical Requirement 220 V - 240 V
• Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or
after the system.
• The estimated replacement time of filter, which is a consumable part, is not an indication of quality guarantee period, but
it means the ideal time of filter replacement. Accordingly, the estimated time of filter replacement may be shortened in
case it is used in an area of poor water quality.
• The filtration device installation shall comply with applicable state and local regulations.
• The reverse osmosis system contains a replaceable treatment component, critical for the effective reduction of total

Others
dissolved solids and that product water shall be tested periodically to verify that the system is performing properly
• The influent water to the system shall include the following characteristics:
o No organic solvents
o Chlorine: < 2 ppm
o pH: 7 - 8
o Temperature: 41 °F ~ 95 °F (5 °C ~ 35 °C)
o Iron: < 2 mg/L
o Turbidity: < 1 NTU
o Hardness: < 1 000 mg/L
• This system has been tested for the treatment of water containing pentavalent arsenic (also know as As(V), As(+5), or

PERFORMANCE DATA SHEET | CHP-7310R

arsenate) at concentrations of 0.050 mg/L or less. This system reduces pentavalent arsenic, but may not remove other
forms of arsenic. This system is to be used on water supplies containing a detectable free chlorine residual at the system
inlet or on water supplies that have been demonstrated to contain only pentavalent arsenic. Treatment with chloramines
(combined chlorine) is not sufficient to ensure complete conversion of trivalent arsenic to pentavalent arsenic. Please see
the Arsenic Facts section of this Performance Data Sheet for further information.
• The compounds certified under NSF/ANSI 401 have been deemed as “incidental contaminants/emerging compounds”.
Incidental contaminants are those compounds that have been detected in drinking water supplies at trace levels. While
occurring at only trace levels, these compounds can affect the public acceptance/perception of drinking water quality.
• Refer to the owner’s manual for specific installation instructions, manufacturer’s limited warranty, user responsibility, and
parts and service availability.
• For parts and service availability, please contact your local dealer or Coway.
Model of Filter Type Usable period (months)
CNFN8S NEO-SENSE FILTER 6
CRMFN8S-20 RO MEMBRANE FILTER 20
CIFN8S-PLUS PLUS INNOSENSE FILTER 18
CAF-03 ANTIBACTERIAL FILTER 12

ARSENIC FACTS
Arsenic (abbreviated As) is found naturally in some well water. Arsenic in water has no color, taste or odor. It must be measured by
a lab test. Public water utilities must have their water tested for arsenic. You can get the results from your water utility. If you have
your own well, you can have the water tested. The local health department or the state environmental health agency can provide
a list of certified labs. The cost is typically $15 to $30. Information about arsenic in water can be found on the Internet at the US
Environmental Protection Agency website:
www.epa.gov/safewater/arsenic.html
There are two forms of arsenic: pentavalent arsenic (also called As(V), As(+5), and arsenate) and trivalent arsenic (also called As(III),
As(+3), and arsenite). In well water, arsenic may be pentavalent, trivalent, or a combination of both. Special sampling procedures
are needed for a lab to determine what type and how much of each type of arsenic is in the water. Check with the labs in your area
to see if they can provide this type of service.
Reverse osmosis (RO) water treatment systems do not remove trivalent arsenic from water very well. RO systems are very effective
at removing pentavalent arsenic. A free chlorine residual will rapidly convert trivalent arsenic to pentavalent arsenic. Other water
treatment chemicals such as ozone and potassium permanganate will also change trivalent arsenic to pentavalent arsenic. A
combined chlorine residual (also called chloramine) may not convert all the trivalent arsenic. If you get your water from a public
water utility, contact the utility to find out if free chlorine or combined chlorine is used in the water system.
The CHP-7310R system is designed to remove pentavalent arsenic. It will not convert trivalent arsenic to pentavalent arsenic. The
system was tested in a lab. Under those conditions, the system reduced 0.050 mg/L pentavalent arsenic to 0.010 mg/L (ppm) (the
USEPA standard for drinking water) or less. The performance of the system may be different at your installation. Have the treated
water tested for arsenic to check if the system is working properly. The RO component of the CHP-7310R system must be replaced 33
every 20 months to ensure the system will continue to remove pentavalent arsenic. The component identification and locations
where you can purchase the component are listed in the installation/operation manual. 34
* VOC Surrogate Claims
Drinking water
Influent challenge Chemical reduction Maximum product water
Chemical regulatory level1
concentration2 mg/L percent concentration mg/L
(MCL/MAC) mg/L
alachlor 0.002 0.050 > 98 0.0013
atrazine 0.003 0.100 > 97 0.0033
benzene 0.005 0.081 > 99 0.0013
carbofuran 0.04 0.190 > 99 0.0013
carbon tetrachloride 0.005 0.078 98 0.00184
chlorobenzene 0.1 0.077 > 99 0.0013
chloropicrin - 0.015 99 0.00023
2,4-D 0.07 0.110 98 0.00174
dibromochloropropane(DBCP) 0.0002 0.052 > 99 0.000023
o-dichlorobenzene 0.6 0.080 > 99 0.0013
p-dichlorobenzene 0.075 0.040 > 98 0.0013
1,2-dichloroethane 0.005 0.088 955 0.00485
cis-1,3-dichloropropylene - 0.079 > 99 0.0013
dinoseb 0.007 0.170 99 0.00024
endrin 0.002 0.053 99 0.000594
ethylbenzene 0.7 0.088 > 99 0.0013
ethylene dilbromide (EDB) 0.00005 0.044 > 99 0.000023
haloacetonitriles (HAN)
bromochloroacetonitrile - 0.022 98 0.00053
dibromoacetonitrile - 0.024 98 0.00063
dichloroacetonitrile - 0.0096 98 0.00023
trichloroacetoritrile - 0.015 98 0.00033
haloketones (HK):
1,1-dichloro-2-propanone - 0.0072 99 0.00013
1,1,1-trichloro-2-propanone - 0.0082 96 0.00033
heptachlor (H-34,Heptox) 0.0004 0.08 > 99 0.0004
heptachlor epoxide 0.0002 0.01076 98 0.00026
hexachlorobutadiene - 0.044 > 98 0.0013
hexachlorocyclopentadiene 0.05 0.060 > 99 0.0000023
lindane 0.0002 0.055 > 99 0.000013
methoxychlor 0.04 0.050 > 99 0.00013
pentachlorophenol 0.001 0.096 > 99 0.0013
simazine 0.004 0.120 > 97 0.0043
styrene 0.1 0.150 > 99 0.00053
1,1,2,2-tetrachloroethane - 0.081 > 99 0.0013
tetrachloroethylene 0.005 0.081 > 99 0.0013
toluene 1 0.078 > 99 0.0013
2,4,5-TP (silvex) 0.05 0.270 99 0.00164
tribromoacetic acid - 0.042 > 98 0.0013
1,2,4-trichlorobenzene 0.07 0.160 > 99 0.00053
1,1,1-trichloroethane 0.2 0.084 95 0.00464
1,1,2-trichloroethane 0.005 0.150 > 99 0.00053
trichloroethylene 0.005 0.180 > 99 0.00103
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform
0.080 0.300 95 0.015
bromodichloromethane
chlorodibromomethane
xylenes (total) 10 0.070 > 99 0.0013
1 These harmonized values were agreed upon by representatives of USEPA and Health Canada for the purpose of evaluating products to the requirements of this Standard.
2 Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
3 Maximum product water level was not observed but was set at the detection limit of the analysis.
4 maximum product water level is set at a value determined in surrogate qualification testing.
5 Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough point as determined in surrogate qualification testing.
6 The surrogate test results for heptachlor epoxide demonstrated a 98% reduction. These data were used to calculate an upper occurrence concentration which would produce
a maximum product water level at the MCL.
Coway Co.,Ltd.
136-23, Yugumagoksa-Ro, Yugu Eub, Gongju-Si, Choongchungnam-Do, Korea
Tel.: 82-41-850-7879 Fax.: 82-41-841-7816
 Others PERFORMANCE DATA SHEET | CHP-7310R

35

36
MEMO
MEMO
MEMO

Others

37

38
 001
9232463

www.coway.com