ENTRY LEVEL CPE MODEL

Entry Level CPE: Fixed Entry Level CPE: Fixed Entry Level CPE: Fixed
FEATURES Broadband (FBB) - Copper Broadband (FBB) - Fiber Broadband (FBB) - Fiber ONT
Wireline ONT v1 v2

WAN (Ethernet) 1 NO NO 1x FE
LAN 1 x FE 1x FE 1x FE
xPON NO YES YES
Wi-Fi YES YES YES
xDSL YES NO NO
FXS PORT (RJ11) 1 NO NO
VOIP YES NO NO
PHONE # 3
1 NO NO
SIM SLOT
WAN (Ethernet) 1 Dedictated port (should not be a switched LAN port)
L

Entry Level CPE: Fixed Entry Level

Wireless Access (FWA) - CPE: Mobile
WAN Ethernet (indoor) WTTX

1X FE NO
1 X FE 1 X FE
NO NO
YES YES
NO NO
1 1
YES YES
1 1
YES
 Bid Evalaution Score Sheet - ENTERY LEVEL CPE: TD-LTE & Mobile (WTTX) Indoor
unit
Bid Name
Bid Number
CPE MODEL Entry Level CPE: TD-LTE & Mobile (WTTX) indoor Unit

EVALUATION CRITERIA

3.1 General Requirements (5%) Description COMMENTS Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

Description Scores Supplier Comment Column1 Column2
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
G.984.1 to G.984.4 and must be certified as compatible with
3.3.1 ITU-T G.984 DasanZhone’s MXK OLT series with software versions N/A
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification. N/A

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s N/A
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks N/A

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in N/A
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 0.50 1

Minimun score for this sub section is 4 4.50 4.50

3.4 802.3 (All CPE Models)

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1
 4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

3.6 3G/4G ( Mobile and FMC Models)

All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G 1 1
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. 1 1

Uplink: Up to 50 Mbps, and downlink: Up to 100 Mbps to be

4 Supported Data rates supported 1 1

a) Uplink Up to 50 Mbps The CPE must provide an uplink connection of up to 50 Mbps 1 1

The CPE must provide a downlink connection of up to 100

b) Downlink Up to 100 Mbps downlink Mbps 1 1

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity; 1 1

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity 1 1

700/800 MHz frequency must be supported for 4G /5 G

7 Frequency support for 4G /5G (optional) connectivity 1 1

The 2300 MHz frequency and Band 40 must be supported for

8 Frequency support for WTTX WTTX connectivity 1 1

The 2600 MHz frequency and Band 41 must be supported for

9 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity 1 1

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and 1 1
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to 1 1
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the 1 1
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
17.00 17.00

SECTION TOTAL 21.5 21.5

3.7 Mandatory Requirements 2 (20%) Description Scores supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) 1 1

4 RJ-45 Ports For ISDN BRI/PRI N/A

5 DECT Digital Enhanced Cordless Communication N/A

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 SIM card slot

Standard Sim card slot Sim card slot (15mmx25mm - maximum size) 1.00 1

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
Wi-Fi Protected Access - WPA3 Wi-Fi Protected Access WPA3 Security 5.00 0

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1 1
3.12 USB Support
1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 23 18

Telephony Support

Mandatory Requirements 3 (20%) Description Scores supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports N/A
3 DECT support (where indicated) DECT support (where indicated) N/A

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 1
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 1
7 Out of Band DTMF event Out of Band DTMF event 1 1
Auto codec period (how it works)
Telephony Support (Voice enabled CPE) General
3.14.3 Features
1 Digit Map Digit Map N/A
2 Multi SIP Accounts Multi SIP Accounts N/A
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support 1 1

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A

6.14.5 Other Features

6.14.5.1 Other Protocolsthat must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 19 19

Mandatory Requirements 4 (15%) Description Scores supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
 11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Scores supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet N/A
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP N/A
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP N/A
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
4 PPP Password required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
5 Bandwidth (uplink & downlink required but modifiable by user via GUI
6 Connection trigger Always On N/A
7 IP protocol version IPv4 N/A
8 IP protocol version IPv6 N/A
VOIP N/A
9 VLAN ID 100 N/A
10 Connection type DHCP (IPoE) N/A
11 Connection trigger Always On N/A
12 IP protocol version IPv4 N/A
 13 IP protocol version IPv6 N/A
TR-069 N/A
14 VLAN ID 800 N/A
15 Connection type DHCP (IPoE) N/A
16 Connection trigger Always On N/A
17 IP protocol version IPv4 N/A
18 IP protocol version IPv6 N/A

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 IP protocol version IPv6 N/A
7 NAT Enable Enable N/A
DSCP Flags for VoIP N/A
8 sip_prio 26 1 1
9 rtp_prio 46 1 1
10 rtcp_prio 46 1 1

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
FAX mode T.38 support for Fax 1 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1 1

2 Are SW versions backward compatable within 1 1

SECTION TOTAL 12 12

6.19 Additional Features and Functionality Scores supplier Comment

TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
Wi-Fi extender / repeaters 5 5
Iot switches 3 3
Ethernet over power line adapter 1 1
Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

OVERALL TOTAL

5% General Requirements (5%) 5.00

23% Mandatory Requirements: Technical 23.00 94% PASS RATE
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces 15.65 77.3% PASS RATE mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 20.00

15% Mandatory Requirements 4: Other 15.00 266.666666666667

features (15%)

15% Mandatory Requirements 5: Pre- 15.00

configuration parameters (20%)
2% Additional Features and Functionality (2%) 2.00

OVERALL SCORE 95.65

FINAL SCORE 57.39
 Bid Evalaution Score Sheet - ENTERY LEVEL CPE: FWA - WAN Ethernet (indoor)
Bid Name
Bid Number
Entry Level CPE: Fixed Wireless Access (FWA) - WAN Ethernet
CPE MODEL
(indoor)

EVALUATION CRITERIA

3.1 General Requirements (5%) Description COMMENTS Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1

SECTION TOTAL 6 0

Mandatory Requirements: Technical

Description Scores Supplier Comment Column1 Column2
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
G.984.1 to G.984.4 and must be certified as compatible with
3.3.1 ITU-T G.984 DasanZhone’s MXK OLT series with software versions N/A
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification. N/A

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s N/A
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks N/A

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in N/A
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 0.50 1

Minimun score for this sub section is 4 4.50 4.50

3.4 802.3 (All CPE Models)

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1
 4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

3.6 3G/4G ( Mobile and FMC Models)

All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. N/A

Uplink: Up to 50 Mbps, and downlink: Up to 100 Mbps to be

4 Supported Data rates supported N/A

a) Uplink Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

The CPE must provide a downlink connection of up to 100

b) Downlink Up to 100 Mbps downlink Mbps N/A

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity N/A

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity N/A

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to N/A
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the N/A
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
4.00 4.00

SECTION TOTAL 8.5 8.5

3.7 Mandatory Requirements 2 (20%) Description Scores supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) 1 1

4 RJ-45 Ports For ISDN BRI/PRI N/A

5 DECT Digital Enhanced Cordless Communication N/A

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
Wi-Fi Protected Access - WPA3 Wi-Fi Protected Access WPA3 Security 5.00

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1 1

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A
3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 22 17

Telephony Support

Mandatory Requirements 3 (20%) Description Scores supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports N/A
3 DECT support (where indicated) DECT support (where indicated) N/A

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 0
3 Echo Cancellation Echo Cancellation 1 0
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 0
7 Out of Band DTMF event Out of Band DTMF event 1 1
Auto codec period (how it works)
Telephony Support (Voice enabled CPE) General
3.14.3 Features
1 Digit Map Digit Map N/A
2 Multi SIP Accounts Multi SIP Accounts N/A
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support 1 1

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A

6.14.5 Other Features

6.14.5.1 Other Protocolsthat must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 19 16

Mandatory Requirements 4 (15%) Description Scores supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
 16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Scores supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet N/A
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP N/A
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP N/A
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
4 PPP Password required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
5 Bandwidth (uplink & downlink required but modifiable by user via GUI
6 Connection trigger Always On 1 1
7 IP protocol version IPv4 1 1
8 IP protocol version IPv6 1 1
VOIP 1 1
9 VLAN ID 100 1 1
10 Connection type DHCP (IPoE) 1 1
11 Connection trigger Always On 1 1
12 IP protocol version IPv4 1 1
13 IP protocol version IPv6 1 1
TR-069 1 1
14 VLAN ID 800 1 1
15 Connection type DHCP (IPoE) 1 1
16 Connection trigger Always On 1 1
 17 IP protocol version IPv4 1 1
18 IP protocol version IPv6 1 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection 1 1

2 Mode Routing 1 1
3 Connection type DHCP 1 1
4 Connection trigger Always On 1 1
5 IP protocol version IPv4 1 1
6 IP protocol version IPv6 1 1
7 NAT Enable Enable 1 1
DSCP Flags for VoIP 1 1
8 sip_prio 26 1 1
9 rtp_prio 46 1 1
10 rtcp_prio 46 1 1

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
FAX mode T.38 support for Fax 1 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1 1

2 Are SW versions backward compatable within 1 1

SECTION TOTAL 36 36

6.19 Additional Features and Functionality Scores supplier Comment

TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
Wi-Fi extender / repeaters 5 5
Iot switches 3 3
Ethernet over power line adapter 1 1
Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

OVERALL TOTAL

5% General Requirements (5%) 0.00

23% Mandatory Requirements: Technical 23.00 94% PASS RATE
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces 15.45 77.3% PASS RATE mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 16.84

15% Mandatory Requirements 4: Other 15.00 266.666666666667

features (15%)

15% Mandatory Requirements 5: Pre- 15.00

configuration parameters (20%)
2% Additional Features and Functionality (2%) 2.00

OVERALL SCORE 87.30

FINAL SCORE 52.38
 Bid Evalaution Score Sheet - Entry Level CPE: Fixed Broadband (FBB) - Copper
Wireline
Bid Name
Bid Number

CPE MODEL Entry Level CPE: Fixed Broadband (FBB) -Copper Wireline

EVALUATION CRITERIA

Supplier
3.1 General Requirements (5%) Description Score Supplier Comment
The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

Description Score Supplier Comment
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers 1 1

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers 1 1

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) 1 1

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers 1 1

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers 1 1

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) 1 1

1 1
3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers 1 1

8 8
3.3 ITU-T G.984: GPON
GPON CPEs must comply with the ITU-T GPON standards
G.984.1 to G.984.4 and must be certified as compatible with
3.3.1 ITU-T G.984 DasanZhone’s MXK OLT series with software versions N/A
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification. N/A

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s N/A
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks N/A

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in N/A
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 0

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 0.5 1

Minimun score for this sub section is 4 4.5 4.0

3.4 802.3 (All CPE Models)
1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1

3 IEEE 802.3ab 1000BASE-T Gbit/s Ethernet over twisted pair at 1 Gbit/s 1 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

3.6 3G/4G ( Mobile and FMC Models)

 All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. N/A

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps

4 Supported Data rates to be supported N/A

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

The CPE must provide a downlink connection of up to 100

b) LTE Downlink Up to 100 Mbps downlink Mbps N/A

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity N/A

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity N/A

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to N/A
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the N/A
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
6.00 6.00

SECTION TOTAL 18.50 18.00

3.7 Mandatory Requirements 2 (20%) Description Score Supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) 1 1

4 RJ-45 Ports For ISDN BRI/PRI

5 DECT Digital Enhanced Cordless Communication

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5 0

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1 1

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
3 Mixed (1020-5000,689) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 22 18 0.7727273

17
Telephony Support

Mandatory Requirements 3 (20%) Description Score Supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated)

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features
 1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1
2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 0
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 0
7 Out of Band DTMF event Out of Band DTMF event 1 1

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map
2 Multi SIP Accounts Multi SIP Accounts
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support 1 1

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call
2 Call Parking Call Parking
3 Message Waiting Indicator Message Waiting Indicator
4 Hot Line Calling Hot Line Calling
5 Music on Hold Music on Hold
6 Anonymous Call Blocking Anonymous Call Blocking
7 Call Block and Filter Call Block and Filter
8 Call Forwarding -- Always Call Forwarding -- Always
9 Call Forwarding -- Busy Call Forwarding -- Busy
10 Call Forwarding -- No Answer Call Forwarding -- No Answer
11 Call Forwarding -- Follow me Call Forwarding -- Follow me
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable
14 Call History Call History
15 Call Hold Call Hold
16 Call ID (Proxy Support) Call ID (Proxy Support)
17 Caller ID Blocking Caller ID Blocking
18 Do Not Disturb Do Not Disturb
19 Cal Back on Busy Cal Back on Busy
20 Direct Inward Dialing Direct Inward Dialing
21 Line Hunting Line Hunting

6.14.5 Other Features

6.14.5.1 Other Protocolsthat must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 19 17

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
Firmware upgrade via web-based UI, Mobile app or
1 TR-069 Firmware upgrade vai web-based UI, Mobile app or TR-069 1 1

File server for Network Attached Storage (NAS)

2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 PVC or Virtual Networks Up to 4 PVC or Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers 1 1
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type 1 1
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 1 1
2 Mode Routing 1 1
3 Connection type PPPOE 1 1
4 PPP Username "Unique. To be entered manually." No Pre-configuring 1 1
required but modifiacble by user via GUI
5 PPP Password "Unique. To be entered manually." No Pre-configuring 1 1
required but modifiacble by user via GUI
6 Connection trigger Always On 1 1
VOIP
7 VPI/VCI 1/35 1 1
 8 Connection type DHCP (IPoE) 1 1
9 Connection trigger Always On 1 1
10 IP protocol version IPv4 1 1
TR-069
11 VPI/VCI 8/35 1 1
12 Connection type DHCP (IPoE) 1 1
13 Connection trigger Always On 1 1
14 IP protocol version IPv4 1 1

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE 1 1
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiacble by user via GUI 1 1

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required but modifiacble by user via GUI 1 1

5 Connection trigger Always On 1 1

6 IP protocol version IPv4 1 1
VOIP
7 VLAN ID 100 1 1
8 Connection type DHCP (IPoE) 1 1
9 Connection trigger Always On 1 1
10 IP protocol version IPv4 1 1
TR-069
11 VLAN ID 800 1 1
12 Connection type DHCP (IPoE) 1 1
13 Connection trigger Always On 1 1
14 IP protocol version IPv4 1 1

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 NAT Enable Enable N/A
DSCP Flags for VoIP
7 sip_prio 26 N/A
8 rtp_prio 46 N/A
9 rtcp_prio 46 N/A

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Fax Mode T.38 support for Fax 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1

2 Are SW versions backward compatable within 1

SECTION TOTAL 37 34

6.19 Additional Features and Functionality

TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
Wi-Fi extender / repeaters 5 5
Iot switches 3 3
Ethernet over power line adapter 1 1
Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

5% General Requirements (5%) 5

23% Mandatory Requirements: Technical 22.3783783783784 97% PASS RATE REQUIRED
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces 16.3636363636364 77.2% PASS RATE REQU mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 17.8947368421053

15% Mandatory Requirements 4: Other 15

features (15%)
15% Mandatory Requirements 5: Pre- 13.7837837837838
configuration parameters (20%)
2% Additional Features and Functionality (2%) 2

OVERALL SCORE 92.42

FINAL SCORE 55.4523212207423
 Bid Evalaution Score Sheet - Entry Level CPE: Fixed Broadband (FBB) - Fiber v1
Bid Name
Bid Number
CPE MODEL Entry Level CPE: Fixed Broadband (FBB) - Fiber ONT v1

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

Description Score Supplier Comment
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
3.3.1 ITU-T G.984 G.984.1 to G.984.4 1 1

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with 1 1
nominal line rates of 2.488 Gbit/s in the downstream direction
and 1.244 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s 1 1
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks 1 1

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in 1 1
Recommendations ITU-T G.984.2 and G.984.3.

5.00 5.00

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 0.50 0.50

Minimun score for this sub section is 4 4.50 4.50

3.4 802.3 (All CPE Models)

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

Telecom Namibia have two OLT vendors namely: Huawei and

Interoperability with GPON OLT's from DSAN Zhone DSAN Zhone. The vendor is responsible to ensure that any
and Huawei software adaptation to ensure interoperatibilty at their own
cost
DSAN 1 1
HUAWEI 1 1
3.6 3G/4G ( Mobile and FMC Models)
All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. N/A

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps

4 Supported Data rates to be supported N/A

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

The CPE must provide a downlink connection of up to 100

b) LTE Downlink Up to 100 Mbps downlink Mbps N/A

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity N/A

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity N/A

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to N/A
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the N/A
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
7 7

SECTION TOTAL 16.50 16.50

3.7 Mandatory Requirements 2 (20%) Description Score Supplier Comment

CPE Interfaces
1 RJ-45 10/100 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) N/A

4 RJ-45 Ports For ISDN BRI/PRI N/A

5 DECT Digital Enhanced Cordless Communication N/A

GPON and AE Interfaces

6 SC/APC connector GPON ONT Fibre Port 1 1
7 SC/UPC connector Active Ethernet ONT Fibre Port 1 1

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
3 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access ( WPA3) Security 5 5

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1 1

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 22 22

Telephony Support

Mandatory Requirements 3 (20%) Description Score Supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports N/A
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports N/A
3 DECT support (where indicated) DECT support (where indicated) N/A

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP N/A

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 N/A
 3 Echo Cancellation Echo Cancellation N/A
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 N/A
5 T.38 Support T.38 support for Fax N/A
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 N/A
7 Out of Band DTMF event Out of Band DTMF event

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map N/A
2 Multi SIP Accounts Multi SIP Accounts N/A
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support N/A

4 Call Pick Up Call Pick Up (where PABX support is required) N/A

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required N/A

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A
N/A

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 10 10

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
 10 IP protocol version IPv4 N/A
TR-069
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
4 PPP Password required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
5 Bandwidth (uplink & downlink required but modifiable by user via GUI
6 Connection trigger Always On 1 1
IP protocol version IPv4 1 1
7 VOIP
8 VLAN ID 100 1 1
9 Connection type DHCP (IPoE) 1 1
10 Connection trigger Always On 1 1
11 IP protocol version IPv4 1 1
12 IP protocol version IPV6 1 1
TR-069 1 1
13 VLAN ID 800 1 1
14 Connection type DHCP (IPoE) 1 1
15 Connection trigger Always On 1 1
16 IP protocol version IPv4 1 1
17 IP protocol version IPV6 1 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 NAT Enable Enable N/A
DSCP Flags for VoIP N/A
7 sip_prio 26 N/A
8 rtp_prio 46 N/A
9 rtcp_prio 46 N/A

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Codec: G.711 A-Law Codec: G.711 A-Law N/A

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1 1

2 Are SW versions backward compatable within 1 1

SECTION TOTAL 22 22

6.19 Additional Features and Functionality (2%)

TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
Wi-Fi extender / repeaters 5 5
Iot switches 1 1
Ethernet over power line adapter 3 3
Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

5% General Requirements (5%) 5

23% Mandatory Requirements: Technical 23 85% PASS RATE REQUIRAll techincal standards must be passed, with exception of the DSAN & Huawei OLT interoperability
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces 20 77.2% PASS RATE mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 20

15% Mandatory Requirements 4: Other 15

features (15%)
15% Mandatory Requirements 5: Pre- 15
configuration parameters (20%)
2% Additional Features and Functionality (2%) 2

OVERALL SCORE 100

FINAL SCORE 60.00
 Bid Evalaution Score Sheet - Entry Level CPE: Fixed Broadband - Fiber ONT v2
Bid Name
Bid Number
CPE MODEL Entry Level CPE: Fixed Broadband (FBB) - Fiber ONT v2

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1

SECTION TOTAL 6 0

Mandatory Requirements: Technical

Description Score supplier Comment
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
3.3.1 ITU-T G.984 G.984.1 to G.984.4 1

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with 1
nominal line rates of 2.488 Gbit/s in the downstream direction
and 1.244 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s 1
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks 1

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in 1
Recommendations ITU-T G.984.2 and G.984.3.

5.00 0.00

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 0.5

Minimun score for this sub section is 4 4.50 0.00

3.4 802.3 (All CPE Models)

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1
standards for interoperable implementations

Telecom Namibia have two OLT vendors namely: Huawei and

Interoperability with GPON OLT's from DSAN Zhone DSAN Zhone. The vendor is responsible to ensure that any
and Huawei software adaptation to ensure interoperatibilty at their own
cost
DSAN 1.00
HUAWEI 1
3.6 3G/4G ( Mobile and FMC Models)
All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. N/A

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps

4 Supported Data rates to be supported N/A

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

The CPE must provide a downlink connection of up to 100

b) LTE Downlink Up to 100 Mbps downlink Mbps N/A

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity N/A

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity N/A

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to N/A
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the N/A
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
7 0

SECTION TOTAL 16.5 0.0

supplier
3.7 Mandatory Requirements 2 (20%) Description Score Supplier Comment
CPE Interfaces
1 RJ-45 10/100 LAN Ports 1
2 RJ-45 10/100 WAN Ports 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) N/A

4 RJ-45 Ports For ISDN BRI/PRI N/A

5 DECT Digital Enhanced Cordless Communication N/A

GPON and AE Interfaces

6 SC/APC connector GPON ONT Fibre Port 1
7 SC/UPC connector Active Ethernet ONT Fibre Port 1

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2, WPA3) Security 1
3 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1
Diagnostics
Auto-configuration and dynamic service provisioning 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1

The CPE shall support both in-band and out-of-band

3 management. 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1

SECTION TOTAL 23 0 0.7826087

Telephony Support

Mandatory Requirements 3 (20%) Description Score supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports N/A
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports N/A
3 DECT support (where indicated) DECT support (where indicated) N/A

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP N/A

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 N/A
3 Echo Cancellation Echo Cancellation N/A
 4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 N/A
5 T.38 Support T.38 support for Fax N/A
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 N/A
7 Out of Band DTMF event Out of Band DTMF event

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map N/A
2 Multi SIP Accounts Multi SIP Accounts N/A
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support N/A

4 Call Pick Up Call Pick Up (where PABX support is required) N/A

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required N/A

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1
2 TCP/IP TCP/IP 1
3 UDP UDP 1
4 ICMP ICMP 1
5 DNS DNS 1
6 DDNS DDNS 1
7 DHCP DHCP 1
8 IGMP IGMP 1
9 FTP FTP 1
10 QoS QoS 1

SECTION TOTAL 10 0

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1

4 IEEE 802.1q IEEE 802.1q 1
5 port-based VLAN port-based VLAN 1
6 Guest Networks Separate and secure network for guest users 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1
15 GUI for Web configuration User friendly GUI for Web configuration 1
16 Downloadable flash software updates Downloadable flash software updates 1
17 System statistics and monitoring System statistics and monitoring 1
18 Web Based Management (WBM) Web Based Management (WBM) 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1
2 Duration of Standard Support Duration of standard support reference 1
3 Duration of Extended Support Duration of Extended Support 1
4 End of Life (Date) End of Life Date 1

SECTION TOTAL 20 0

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1
2 Country: Namibia Country: Namibia 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69
6 Status: Enabled 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
 TR-069
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 1
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
4 PPP Password required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
5 Bandwidth (uplink & downlink required but modifiable by user via GUI
6 Connection trigger Always On 1
IP protocol version IPv4 1
7 VOIP
8 VLAN ID 100 1
9 Connection type DHCP (IPoE) 1
10 Connection trigger Always On 1
11 IP protocol version IPv4 1
12 IP protocol version IPv6 1
TR-069 1
13 VLAN ID 800 1
14 Connection type DHCP (IPoE) 1
15 Connection trigger Always On 1
16 IP protocol version IPv4 1
17 IP protocol version IPv6 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 NAT Enable Enable N/A
DSCP Flags for VoIP N/A
7 sip_prio 26 N/A
8 rtp_prio 46 N/A
9 rtcp_prio 46 N/A

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Codec: G.711 A-Law Codec: G.711 A-Law N/A

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1

2 Are SW versions backward compatable within 1

SECTION TOTAL 22 0

6.19 Additional Features and Functionality

TR-369 1
Others 1
6.19 Accessories that support CPE on offer
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1
Wi-Fi extender / repeaters 5
Iot switches 1
Ethernet over power line adapter 3
Lead Time
8 weeks delivery 1
13 0

5% General Requirements (5%) 0

23% Mandatory Requirements: Technical 0 85% PASS RATE REQUIRAll techincal standards must be passed, with exception of the DSAN & Huawei OLT interoperability
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces 0 78% PASS RATE REQUIR mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 0

15% Mandatory Requirements 4: Other 0

features (15%)
15% Mandatory Requirements 5: Pre- 0
configuration parameters (20%)
2% Additional Features and Functionality (2%) 0

OVERALL SCORE 0.00

FINAL SCORE 0
 HIGH END CPE MODEL
High End CPE: FBB - High End CPE:FBB -Fiber High End CPE: FWA -
FEATURES copper wireline ONT WAN Ethernet (indoor)

WAN (Ethernet) 1 1x GE 1x GE 1 X GE
LAN 4 x GE 4x GE 4 X GE
xPON NO YES NO
Wi-Fi YES YES YES
xDSL YES NO NO
FXS PORT (RJ11) 2 2 2
DECT SUPPORT **YES **YES **YES
VOIP YES YES YES
PHONE # 3 6 6 6
SIMULTANEOUS
6 6 6
CALLS

WAN (Ethernet) 1 A LAN port may be switched WAN port)

**YES DECT SUPPORT becomes optional if there are other ways to register 4 other telephony devices
r 4 other telephony devices
 Bid Evalaution Score Sheet - Fixed End CPE: FBB - Copper Wireline
Bid Name
Bid Number
CPE MODEL High End CPE: FBB - copper wireline

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.

3.1.3 Identification of Equipment The CPE will be marked with the suppliers name/id mark and 1 1
equipment model/type reference
3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

Description Score Supplier Comment
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers 1 1

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers 1 1

3 ITU-T Rec. 992.5 Annexure M Asymmetric digital subscriber line 2 (ADSL2) transceivers – 1 1
Extended bandwidth ADSL2 (ADSL2plus)

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers 1 1

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers 1 1

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) 1 1

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers 1 1

7 7
3.3 ITU-T G.984: GPON
GPON CPEs must comply with the ITU-T GPON standards
G.984.1 to G.984.4 and must be certified as compatible with
3.3.1 ITU-T G.984 DasanZhone’s MXK OLT series with software versions N/A
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

2 ITU-T Rec. G.984.2 Gigabit-capable Passive Optical Networks (GPON): Physical N/A
Media Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s N/A
in the upstream direction

4 ITU-T Rec. G.984.3 Specifies the transmission convergence layer for gigabit- N/A
capable passive optical networks

provides the optical network termination (ONT) management

5 ITU-T Rec. G.984.4 and control interface (OMCI) specification for gigabit-capable N/A
passive optical network (G-PON) systems as defined in
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

1 IEEE 802.11a Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM 1 1

encoding rather than FHSS/DSSS

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

3 IEEE 802.11g Used for transmission over short distances at up to 54-Mbps 1 1

in the 2.4 GHz bands

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

5 IEEE 802.11ac Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps 1 1
in a three antenna design
6 IEEE 802.11ax 0.50 0.50
Minimun score for this sub section is 5 5.5 5.5
3.4 802.3 (All CPE Models)
1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
 2 IEEE 802.3u 100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100 1 1
Mbit/s (12.5 Mbit/s) with auto negotiation
3 IEEE 802.3ab 1000BASE-T Gbit/s Ethernet over twisted pair at 1 Gbit/s 1 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

3.6 3G/4G ( Mobile and FMC Models)

All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

3 3G Fallback for 4G supported devices 4G support must allow automatic 3G fallback if/when 4G N/A
signal strength becomes low.

4 Supported Data rates LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps N/A
to be supported

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

b) LTE Downlink Up to 100 Mbps downlink The CPE must provide a downlink connection of up to 100 N/A
Mbps

5 Frequency support for 3G The 900 MHz and 2100MHz frequency must be supported for N/A
3G Connectivity

6 Frequency support for 4G The 1800 MHz frequency must be supported for 4G N/A
connectivity

7 Frequency support for TD LTE & WTTX The 2300 MHz frequency and Band 40 must be supported for N/A
TD-LTE & WTTX connectivity

8 Frequency support for TD LTE & WTTX The 2600 MHz frequency and Band 41 must be supported for N/A
TD-LTE & WTTX connectivity
Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User N/A
Password for us to control the Routers on TDD-LTE & WTTX to
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network N/A
within that Frequency. We want to be able to logon to the
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)

6.00 6.00
SECTION TOTAL 18.5 18.5

3.7 Mandatory Requirements 2 (20%) Description Score supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

3 RJ-11 FXS Ports For analogue phones or for Fax. (Not applicable to Entry Level 1 1
A and High End Level A CPE offered)
4 RJ-45 Ports For ISDN BRI/PRI
5 DECT Digital Enhanced Cordless Communication 1 1

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
3 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5 5
4 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1

2 The CPE shall be TR-069 enabled and be able to support a 3rd 1 1

party ACS

3 The CPE shall support both in-band and out-of-band 1 1

management.
3.11 Access Control
1 Block Website Create a lis of Websites which must not be accessed 1 1

2 Block MAC Address Control when clients or PC's connected to the device are 1 1
allowed to access the internet

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
3 Mixed (1020-5000,689) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 25 25 0.8

Telephony Support

Mandatory Requirements 3 (20%) Description Score supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated) 1 1

3.14.2 Telephony Support (Voice enabled CPE) Telephone

Features
1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1
2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 1
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 1
7 Out of Band DTMF event Out of Band DTMF event 1 1

3.14.3 Telephony Support (Voice enabled CPE) General

Features
1 Digit Map Digit Map 1 1
2 Multi SIP Accounts Multi SIP Accounts 1 1

3 Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support
Support
4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

3.14.4 Telephony Support (Voice enabled CPE) Optional

General Features
1 3 Party Call 3 Party Call
2 Call Parking Call Parking
3 Message Waiting Indicator Message Waiting Indicator
4 Hot Line Calling Hot Line Calling
5 Music on Hold Music on Hold
6 Anonymous Call Blocking Anonymous Call Blocking
7 Call Block and Filter Call Block and Filter
8 Call Forwarding -- Always Call Forwarding -- Always
9 Call Forwarding -- Busy Call Forwarding -- Busy
10 Call Forwarding -- No Answer Call Forwarding -- No Answer
11 Call Forwarding -- Follow me Call Forwarding -- Follow me
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable
14 Call History Call History
15 Call Hold Call Hold
16 Call ID (Proxy Support) Call ID (Proxy Support)
17 Caller ID Blocking Caller ID Blocking
18 Do Not Disturb Do Not Disturb
19 Cal Back on Busy Cal Back on Busy
20 Direct Inward Dialing Direct Inward Dialing
21 Line Hunting Line Hunting

6.14.5 Other Features

6.14.5.1 Other Protocolsthat must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 21 21

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
 1 Firmware upgrade via web-based UI, Mobile app or Firmware upgrade vai web-based UI, Mobile app or TR-069 1 1
TR-069

2 File server for Network Attached Storage (NAS) File server for Network Attached Storage (NAS) Devices
Devices
3 Web Filtering Web Filtering 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 PVC or Virtual Networks Up to 4 PVC or Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers 1 1
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type 1 1
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 1 1
2 Mode Routing 1 1
3 Connection type PPPOE 1 1
4 PPP Username "Unique. To be entered manually." No Pre-configuring 1 1
required but modifiacble by user via GUI
5 PPP Password "Unique. To be entered manually." No Pre-configuring 1 1
required but modifiacble by user via GUI
6 Connection trigger Always On 1 1
VOIP
7 VPI/VCI 1/35 1 1
8 Connection type DHCP (IPoE) 1 1
9 Connection trigger Always On 1 1
10 IP protocol version IPv4 1 1
TR-069
11 VPI/VCI 8/35 1 1
12 Connection type DHCP (IPoE) 1 1
13 Connection trigger Always On 1 1
14 IP protocol version IPv4 1 1

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE 1 1

3 PPP Username "Unique. To be entered manually." No Pre-configuring 1 1

required but modifiacble by user via GUI

4 PPP Password "Unique. To be entered manually." No Pre-configuring 1 1

required but modifiacble by user via GUI
5 Connection trigger Always On 1 1
6 IP protocol version IPv4 1 1
VOIP
7 VLAN ID 100 1 1
8 Connection type DHCP (IPoE) 1 1
9 Connection trigger Always On 1 1
10 IP protocol version IPv4 1 1
TR-069
11 VLAN ID 800 1 1
12 Connection type DHCP (IPoE) 1 1
13 Connection trigger Always On 1 1
14 IP protocol version IPv4 1 1

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
 3 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required

4 PPP Password "Unique. To be entered manually." No Pre-configuring N/A

required
5 Connection trigger Always On N/A
6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A
N/A

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 NAT Enable Enable N/A
DSCP Flags for VoIP N/A
7 sip_prio 26 N/A
8 rtp_prio 46 N/A
9 rtcp_prio 46 N/A

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A
N/A

3.17.7 Pre- Configuration Parameters Supported for

analogue Fax implementation (Voice CPE)
Fax Mode T.38 support for Fax N/A

3.18 Software Updates and Upgrades

1 Does the supplier offer all future Software Updates 1 1

and Upgrades for free
2 Are SW versions backward compatable within 1 1

SECTION TOTAL 36 36

6.19 Additional Features and Functionality

TR-369 1 1
others 1 1

6.2 Accessories that support CPE on offer

Wi-Fi extender (Wi-fi Mesh) / repeaters 5 5
Iot switches 1 1
Ethernet over power line adapter 3 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
6.3 Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

5% General Requirements (5%) 5

23% Mandatory Requirements: Technical 23 97% PASS RATE REQUIRED
Standards (23%)

20% Mandatory Requirements 2: Interfaces 20 80% PASS RATE REQUIR only WPA3 is not
(20%) mandatory

20% Mandatory Requirements 3:Telephony Support 20

(20%)

15% Mandatory Requirements 4: Other 15

features (15%)
15% Mandatory Requirements 5: Pre- 15
configuration parameters (20%)
2% Additional Features and Functionality (2%) 2

FINAL SCORE 100.00

FINAL SCORE 60
 Bid Evalaution Score Sheet - High End CPE: FBB - Fiber ONT
Bid Name
Bid Number
CPE MODEL High End CPE: FBB - Fiber ONT

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

Description Score supplier Comment
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

Han+C33:D38dshake Procedure for digital subscriber line
ITU-T Rec. 994.1 transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
3.3.1 ITU-T G.984 G.984.1 to G.984.4 1 1

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with 1 1
nominal line rates of 2.488 Gbit/s in the downstream direction
and 1.244 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s 1 1
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks 1 1

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in 1 1
Recommendations ITU-T G.984.2 and G.984.3.

5.00 5.00

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 1 1

IEEE 802.11ax 0.50 0.50

Minimun score for this sub section is 5 5.5 6

3.4 802.3 (All CPE Models)

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

3.5.1 Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

Telecom Namibia have two OLT vendors namely: Huawei and

Interoperability with GPON OLT's from DSAN Zhone DSAN Zhone. The vendor is responsible to ensure that any
and Huawei software adaptation to ensure interoperatibilty at their own
cost
 DSAN 1.00 1
Huawei 1 1
3.6 3G/4G ( Mobile and FMC Models)
All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. N/A

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps

4 Supported Data rates to be supported N/A

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

The CPE must provide a downlink connection of up to 100

b) LTE Downlink Up to 100 Mbps downlink Mbps N/A

The 900 MHz and 2100MHz frequency must be supported for

Frequency support for 3G 3G Connectivity N/A

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity N/A

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity N/A

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to N/A
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the N/A
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)

7.00 7.00
SECTION TOTAL 17.5 17.5

3.7 Mandatory Requirements 2 (20%) Description Score supplier Comment

CPE Interfaces
1 RJ-45 10/100 /1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level

3 RJ-11 FXS Ports A and High End Level A CPE offered) 1 1

4 RJ-45 Ports For ISDN BRI/PRI

5 DECT Digital Enhanced Cordless Communication 1 1

GPON and AE Interfaces

6 SC/APC connector GPON ONT Fibre Port 1 1
7 SC/UPC connector Active Ethernet ONT Fibre Port 1 1

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2, WPA3) Wi-Fi Protected Access (WPA,WPA2, WPA3) Security 1 1
4 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5 5
4 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1 1

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 26 26 0.8076923

Telephony Support

Mandatory Requirements 3 (20%) Description Score supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated) 1 1

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features
 1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1
2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 1
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 1
7 Out of Band DTMF event Out of Band DTMF event 1 1

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map 1 1
2 Multi SIP Accounts Multi SIP Accounts 1 1
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support 1 1

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 22 22

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP
7 VPI/VCI 1/35 N/A
 8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required N/A

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
4 PPP Password required but modifiable by user via GUI
"Unique. To be entered manually." No Pre-configuring
5 Bandwidth (uplink & downlink required but modifiable by user via GUI
6 Connection trigger Always On 1 1
IP protocol version IPv4 1 1
7 VOIP
8 VLAN ID 100 1 1
9 Connection type DHCP (IPoE) 1 1
10 Connection trigger Always On 1 1
IP protocol version IPv4 1 1
11 TR-069 1 1
12 VLAN ID 800 1 1
13 Connection type DHCP (IPoE) 1 1
14 Connection trigger Always On 1 1
IP protocol version IPv4 1 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection N/A

2 Mode Routing N/A

3 Connection type DHCP N/A
4 Connection trigger Always On N/A
5 IP protocol version IPv4 N/A
6 NAT Enable Enable N/A
DSCP Flags for VoIP N/A
7 sip_prio 26 N/A
8 rtp_prio 46 N/A
9 rtcp_prio 46 N/A

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Codec: G.711 A-Law Codec: G.711 A-Law N/A

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1 1

2 Are SW versions backward compatable within 1 1

SECTION TOTAL 20 20

6.19 Additional Features and Functionality

TR-369 1 1
Others 1 1
6.19 Accessories that support CPE on offer
Wi-Fi extender (Wi-Fi Mesh) / repeaters 5 5
Iot switches 1 1
Ethernet over power line adapter 3 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Lead Time
8 weeks delivery 1 1
13 13

5% General Requirements (5%) 5.00

23% Mandatory Requirements: Technical Standards (23%) 23.00 86% PASS RATE REQUIRAll techincal standards must be passed, with exception of the DSAN & Huawei OLT interoperability

only WPA3 is not

20% Mandatory Requirements 2: Interfaces (20%) 20.00 80.7% PASS RATE REQU mandatory
Mandatory Requirements 3:Telephony Support
20% (20%) 20.00

15% Mandatory Requirements 4: Other features (15%) 15.00

15% Mandatory Requirements 5: Pre-configuration

parameters (20%) 15.00
2% Additional Features and Functionality (2%) 2.00

Final Score 100.00

Final Score 60
 Bid Evalaution Score Sheet - High End CPE: FWA - WAN Ethernet indoor
Bid Name
Bid Number
CPE MODEL High End CPE: FWA - WAN (indoor)

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
3.1.1 Power Supply mains voltage, 230V and frequency 50 Hz. Power plug should 1 1
be Type D or Type M, Alternatively TN will also consider Type
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1 1
can be recommended.

3.1.3 Identification of Equipment The CPE will be marked with the suppliers name/id mark and 1 1
equipment model/type reference
3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical Standards

Description Score supplier Comment
(20%)
3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

3 ITU-T Rec. 992.5 Annexure M Asymmetric digital subscriber line 2 (ADSL2) transceivers – N/A
Extended bandwidth ADSL2 (ADSL2plus)

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards
3.3.1 ITU-T G.984 G.984.1 to G.984.4 and must be certified as compatible with N/A
DasanZhone’s MXK OLT series with software versions
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

2 ITU-T Rec. G.984.2 Gigabit-capable Passive Optical Networks (GPON): Physical N/A
Media Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and

3 2488.320 Mbit/s in the downstream direction and 155.520 N/A
Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s
in the upstream direction

4 ITU-T Rec. G.984.3 Specifies the transmission convergence layer for gigabit- N/A
capable passive optical networks

provides the optical network termination (ONT) management

5 ITU-T Rec. G.984.4 and control interface (OMCI) specification for gigabit-capable N/A
passive optical network (G-PON) systems as defined in
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

1 IEEE 802.11a Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM 1 1

encoding rather than FHSS/DSSS

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

3 IEEE 802.11g Used for transmission over short distances at up to 54-Mbps 1 1

in the 2.4 GHz bands

an extension which adds MIMO. The additional antenna allow

4 IEEE 802.11n for increased data throughput through spatial multiplexing 1 1
and increased range. Provides up to 100 Mbps transmission
speeds.

5 IEEE 802.11ac Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps 1 1
in a three antenna design

6 IEEE 802.11ax 0.50 1

Minimun score for this sub section is 5 5.5 5.5
3.4 802.3 (All CPE Models)
1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1

2 IEEE 802.3u 100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100 1 1

Mbit/s (12.5 Mbit/s) with auto negotiation

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1
3.5 802.1 (All CPE Models)

IEEE 802.1q Standard for local and metropolitan networks -- Media access 1 1
control bridges and virtual bridged local area networks

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

5 5
3.6 3G/4G ( Mobile and FMC Models)
All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G N/A
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide N/A
fail-safe connectivity for mobile broadband access.

3 3G Fallback for 4G supported devices 4G support must allow automatic 3G fallback if/when 4G N/A
signal strength becomes low.

4 Supported Data rates Uplink: Up to 50 Mbps, and downlink: Up to 100 Mbps to be N/A
supported

a) Uplink Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps N/A

b) Downlink Up to 100 Mbps downlink The CPE must provide a downlink connection of up to 100 N/A
Mbps

5 Frequency support for 3G The 900 MHz and 2100MHz frequency must be supported for N/A
3G Connectivity

6 Frequency support for 4G The 1800 MHz frequency must be supported for 4G N/A
connectivity

7 Frequency support for TD LTE & WTTX The 2300 MHz frequency and Band 40 must be supported for N/A
TD-LTE & WTTX connectivity

8 Frequency support for TD LTE & WTTX The 2600 MHz frequency and Band 41 must be supported for N/A
TD-LTE & WTTX connectivity
Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and N/A
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User N/A
Password for us to control the Routers on TDD-LTE & WTTX to
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network N/A
within that Frequency. We want to be able to logon to the
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)

SECTION TOTAL 10.5 10.5

3.7 Mandatory Requirements 2 (20%) Description Score supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

3 RJ-11 FXS Ports For analogue phones or for Fax. (Not applicable to Entry Level 1 1
A and High End Level A CPE offered)
4 RJ-45 Ports For ISDN BRI/PRI
5 DECT Digital Enhanced Cordless Communication 1 1

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2, WPA3) Wi-Fi Protected Access (WPA,WPA2,WPA3) Security 1 1
Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5 1
3 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1
6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1 1
Diagnostics
Auto-configuration and dynamic service provisioning 1 1

2 The CPE shall be TR-069 enabled and be able to support a 3rd 1 1

party ACS

3 The CPE shall support both in-band and out-of-band 1 1

management.

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1

2 Block MAC Address Control when clients or PC's connected to the device are 1 1
allowed to access the internet

3.12 USB Support

1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

 1 Range (e.g. 50-100) The user should be able to open this ports on the CPE and 1 1
redirect data through this ports to a single PC on the LAN

2 Individual (e.g. 80, 68, 888) The user should be able to open this ports on the CPE and 1 1
redirect data through this ports to a single PC on the LAN

SECTION TOTAL 24 20 0.7916667

Telephony Support

Mandatory Requirements 3 (20%) Description Score supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated) 1 1

3.14.2 Telephony Support (Voice enabled CPE) Telephone Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1
2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 1
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 1
7 Out of Band DTMF event Out of Band DTMF event 1 1
Auto codec period (how it works)
3.14.3 Telephony Support (Voice enabled CPE) General Features
1 Digit Map Digit Map 1 1
2 Multi SIP Accounts Multi SIP Accounts 1 1

3 Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support 1 1

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

3.14.4 Telephony Support (Voice enabled CPE) Optional General

Features
1 3 Party Call 3 Party Call N/A
2 Call Parking Call Parking N/A
3 Message Waiting Indicator Message Waiting Indicator N/A
4 Hot Line Calling Hot Line Calling N/A
5 Music on Hold Music on Hold N/A
6 Anonymous Call Blocking Anonymous Call Blocking N/A
7 Call Block and Filter Call Block and Filter N/A
8 Call Forwarding -- Always Call Forwarding -- Always N/A
9 Call Forwarding -- Busy Call Forwarding -- Busy N/A
10 Call Forwarding -- No Answer Call Forwarding -- No Answer N/A
11 Call Forwarding -- Follow me Call Forwarding -- Follow me N/A
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional N/A
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable N/A
14 Call History Call History N/A
15 Call Hold Call Hold N/A
16 Call ID (Proxy Support) Call ID (Proxy Support) N/A
17 Caller ID Blocking Caller ID Blocking N/A
18 Do Not Disturb Do Not Disturb N/A
19 Cal Back on Busy Cal Back on Busy N/A
20 Direct Inward Dialing Direct Inward Dialing N/A
21 Line Hunting Line Hunting N/A

6.14.5 Other Features

6.14.5.1 Other Protocolsthat must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 22 22

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
2 File server for Network Attached Storage (NAS) Devices File server for Network Attached Storage (NAS) Devices
3 Web Filtering Web Filtering 1 1
4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration 1 1
16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1 1
 2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date 1 1

SECTION TOTAL 20 20
supplier
Mandatory Requirements 5 (20%) Description Score supplier Comment

3.17 Pre- Configuration Parameters Supported. Must be pre-

configured on test units to be provided with offer

3.17.1 The following general parameters are specific to Telecom Namibia

and must be pre-configured onto the CPE by the supplier:

1 Language: English (South Africa) Language: English (South Africa) 1 1

2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled 1 1

3.17.2 Pre- Configuration Parameters Supported for ADSL CPE. Must

be pre-configured on test units to be provided with offer

Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

3.17.3 Pre- Configuration Parameters Supported for VDSL CPE. Must be

pre-configured on test units to be provided with offer

Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A

3 PPP Username "Unique. To be entered manually." No Pre-configuring N/A

required

4 PPP Password "Unique. To be entered manually." No Pre-configuring N/A

required
5 Connection trigger Always On N/A
6 IP protocol version IPv4 N/A
VOIP
7 VLAN ID 100 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069
11 VLAN ID 800 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A

3.17.4 The following parameters must be pre-configured for WIMAX or

FTTH (WAN Ethernet) implementation
Internet
1 VLAN ID 200 1 1
2 Connection type PPPOE

3 PPP Username "Unique. To be entered manually." No Pre-configuring

required but modifiable by user via GUI

4 PPP Password "Unique. To be entered manually." No Pre-configuring

required but modifiable by user via GUI

5 Bandwidth (uplink & downlink "Unique. To be entered manually." No Pre-configuring

required but modifiable by user via GUI
6 Connection trigger Always On 1 1
7 IP protocol version IPv4 1 1
8 IP protocol version IPv6 1 1
VOIP 1 1
8 VLAN ID 100 1 1
9 Connection type DHCP (IPoE) 1 1
10 Connection trigger Always On 1 1
11 IP protocol version IPv4 1 1
12 IP protocol version IPV6 1 1
TR-069 1 1
13 VLAN ID 800 1 1
14 Connection type 1
Http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
15 Connection trigger Always On 1 1
16 IP protocol version IPv4 1 1
17 IP protocol version IPv6 1 1

3.17.5 The following parameters must be pre-configured for TD-LTE

(WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection 1 1

2 Mode Routing 1 1
3 Connection type DHCP 1 1
4 Connection trigger Always On 1 1
5 IP protocol version IPv4 1 1
6 NAT Enable Enable 1 1
DSCP Flags for VoIP 1 1
 7 sip_prio 26 1 1
8 rtp_prio 46 1 1
9 rtcp_prio 46 1 1

3.17.6 Pre- Configuration Parameters Supported for VSAT CPE. Must

be pre-configured on test units to be provided with offer

1 Data: VLAN ID 24 Data: VLAN ID 24

2 Voice: VLAN ID 2668 Voice: VLAN ID 2668
3 Management: TBD Management: TBD

3.17.7 Pre- Configuration Parameters Supported for analogue Fax

implementation (Voice CPE)
FAX mode T.38 support for Fax 1 1

3.18 Software Updates and Upgrades

1 Does the supplier offer all future Software Updates and Upgrades 1 1
for free
2 Are SW versions backward compatable within 1 1

SECTION TOTAL 35 35

6.19 Additional Features and Functionality

TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi extender (Wi-fi Mesh) / repeaters 5 5
Iot switches 1 1
Ethernet over power line adapter 3 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1
Lead Time
8 weeks delivery 1 1
13 13

5% General Requirements (5%) 5

23% Mandatory Requirements: Technical Standards (23%) 23 95% PASS RATE REQUIRED

20% Mandatory Requirements 2: Interfaces (20%) only WPA3 is not

16.6666666666667 79.2% PASS RATE REQU mandatory

20% Mandatory Requirements 3:Telephony Support (20%) 20

15% Mandatory Requirements 4: Other features (15%) 15

15% Mandatory Requirements 5: Pre-configuration parameters (20%) 15

2% Additional Features and Functionality (2%) 2

OVERALL TOTAL 96.67

FINAL SCORE 58
 Advanced (Hybrid) Level CPE MODEL
Hybrid C: Fixed
Hybrid A: Fixed Broadband Hybrid B: Fixed BB +
BB + Wireless Acess
FEATURES + Wireless Access - Copper Wireless Acess - Fiber +
- Fiber + TDD +
+TDD + FDD indoor TDD + FDD indoor
FDD indoor
WAN (Ethernet) 1 1x GE 1x GE 1x GE
LAN 4 x GE 4x GE 4x GE
AE NO NO YES
xPON NO YES NO
Wi-Fi YES YES YES
xDSL YES NO NO
FXS PORT (RJ11) 2 2 2
DECT SUPPORT **YES **YES **YES
VOIP YES YES YES
PHONE # 3 6 6 6
SIMULTANEOUS
6 6 6
CALLS

**YES DECT SUPPORT becomes optional if there are other ways to register 4 other telephony devices
WAN (Ethernet) 1 LAN port may be switched to a WAN port)
other telephony devices
 Bid Evalaution Score Sheet - Hybrid A: Fixed Bpradband + Wireless Access -
Copper+TDD+FDD indoor
Bid Name
Bid Number
Hybrid A: Fixed Broadband + Wireless Acess - Copper +TDD + FDD
CPE MODEL
indoor

EVALUATION CRITERIA

3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC
mains voltage, 230V and frequency 50 Hz. Power plug should
3.1.1 Power Supply be Type D or Type M, Alternatively TN will also consider Type 1
C and Type N

Tenderers should indicate what surge protection the specific

3.1.2 Voltage Protection CPE has on board. Alternatively a surge protection accessory 1
can be recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1

3.1.4

The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory 1
Authority of Namibia (CRAN) if the Tender is successful.

b) Safety CPE must comply with IEC 60950-1 safety standards 1

3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1

SECTION TOTAL 6 0

Mandatory Requirements: Technical

Description Score supplier Comment
Standards (20%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers 1

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers 1

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) 1

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers 1

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers 1

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) 1

1
3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers 1

8 0
3.3 ITU-T G.984: GPON
GPON CPEs must comply with the ITU-T GPON standards
G.984.1 to G.984.4 and must be certified as compatible with
3.3.1 ITU-T G.984 DasanZhone’s MXK OLT series with software versions N/A
2.5.1.423 or newer.

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements
1 ITU-T Rec. G.984.1 of business and residential services and covers systems with N/A
nominal line rates of 2.4 Gbit/s in the downstream direction
and 1.2 Gbit/s and 2.4 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical

2 ITU-T Rec. G.984.2 Media Dependent (PMD) layer specification. N/A

GPON with nominal line rates of 1244.160 Mbit/s and

2488.320 Mbit/s in the downstream direction and 155.520
3 Mbit/s, 622.080 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s N/A
in the upstream direction

Specifies the transmission convergence layer for gigabit-

4 ITU-T Rec. G.984.3 capable passive optical networks N/A

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in N/A
Recommendations ITU-T G.984.2 and G.984.3.

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1

Used for transmission over short distances at up to 54-Mbps

3 IEEE 802.11g in the 2.4 GHz bands 1

an extension which adds MIMO. The additional antenna allow

for increased data throughput through spatial multiplexing
4 IEEE 802.11n and increased range. Provides up to 100 Mbps transmission 1
speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps
5 IEEE 802.11ac in a three antenna design 1

IEEE 802.11ax 0.50

Minimun score for this sub section is 5 5.5 0.0
3.4 802.3 (All CPE Models)
1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1
 3 IEEE 802.3ab 1000BASE-T Gbit/s Ethernet over twisted pair at 1 Gbit/s 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1

Certification compliance

BBF.247 certification compliance. Conformance to TR-156 and

Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1
standards for interoperable implementations

3.6 3G/4G ( Mobile and FMC Models)

All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G 1
LTE signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL,

2 FMC WiMAX, TD-LTE) Ethernet WAN connection which will provide 1
fail-safe connectivity for mobile broadband access.

4G support must allow automatic 3G fallback if/when 4G

3 3G Fallback for 4G supported devices signal strength becomes low. 1

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 150

4 Supported Data rates Mbps to be supported

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps 1

The CPE must provide a downlink connection of up to 150

b) LTE Downlink Up to 100 Mbps downlink Mbps 1

The 900 MHz and 2100MHz frequency must be supported for

5 Frequency support for 3G 3G Connectivity 1

The 1800 MHz frequency must be supported for 4G

6 Frequency support for 4G connectivity 1

The 2300 MHz frequency and Band 40 must be supported for

7 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity 1

The 2600 MHz frequency and Band 41 must be supported for

8 Frequency support for TD LTE & WTTX TD-LTE & WTTX connectivity 1

Please note that For TD-LTE & WTTX, the CPE need to be
enabled for us to lock it via Selected Band, Frequency and 1
a) Physical ID.

It will be good if the above mentioned functionality will be

enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to 1
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will

support the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the 1
Routers interface and to lock it via Selected Band, Frequency
and Physical ID
c)
18.00 0.00

SECTION TOTAL 31.5 0.0

3.7 Mandatory Requirements 2 (20%) Description Score supplier Comment

CPE Interfaces
1 RJ-45 10/100/1000 LAN Ports 1
2 RJ-45 10/100/1000 WAN Ports 1

Telephony Support (Voice enabled CPE) Interfaces

For analogue phones or for Fax. (Not applicable to Entry Level
3 RJ-11 FXS Ports A and High End Level A CPE offered) 1

4 RJ-45 Ports For ISDN BRI/PRI

5 DECT / Other alternative to register 4 devices Digital Enhanced Cordless Communication 1

GPON and AE Interfaces

6 SC/UPC connector GPON ONT Fibre Port N/A
7 SC/UPC connector Active Ethernet ONT Fibre Port N/A

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1
3 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5
4 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1
6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image
1 TR-069 Management Support management, Status and performance monitoring and 1
Diagnostics
Auto-configuration and dynamic service provisioning 1
The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1

The CPE shall support both in-band and out-of-band

3 management. 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1
Control when clients or PC's connected to the device are
2 Block MAC Address allowed to access the internet 1
3.12 USB Support
1 File Server File Server supported on USB N/A
2 Print Server Print Server supported on USB N/A

3.13 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1

SECTION TOTAL 24 0 0.7916667

Telephony Support

Mandatory Requirements 3 (20%) Description Score supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated) 1

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1
3 Echo Cancellation Echo Cancellation 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1
5 T.38 Support T.38 support for Fax 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1
7 Out of Band DTMF event Out of Band DTMF event 1

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map 1
2 Multi SIP Accounts Multi SIP Accounts 1
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call
2 Call Parking Call Parking
3 Message Waiting Indicator Message Waiting Indicator
4 Hot Line Calling Hot Line Calling
5 Music on Hold Music on Hold
6 Anonymous Call Blocking Anonymous Call Blocking
7 Call Block and Filter Call Block and Filter
8 Call Forwarding -- Always Call Forwarding -- Always
9 Call Forwarding -- Busy Call Forwarding -- Busy
10 Call Forwarding -- No Answer Call Forwarding -- No Answer
11 Call Forwarding -- Follow me Call Forwarding -- Follow me
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable
14 Call History Call History
15 Call Hold Call Hold
16 Call ID (Proxy Support) Call ID (Proxy Support)
17 Caller ID Blocking Caller ID Blocking
18 Do Not Disturb Do Not Disturb
19 Cal Back on Busy Cal Back on Busy
20 Direct Inward Dialing Direct Inward Dialing
21 Line Hunting Line Hunting

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1
2 TCP/IP TCP/IP 1
3 UDP UDP 1
4 ICMP ICMP 1
5 DNS DNS 1
6 DDNS DDNS 1
7 DHCP DHCP 1
8 IGMP IGMP 1
9 FTP FTP 1
10 QoS QoS 1

SECTION TOTAL 21 0

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
Firmware upgrade via web-based UI, Mobile app or TR-
1 069 Firmware upgrade vai web-based UI, Mobile app or TR-069 1

2 File server for Network Attached Storage (NAS) Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1

5 port-based VLAN port-based VLAN 1
6 Guest Networks Separate and secure network for guest users 1
7 Up to 4 PVC or Virtual Networks Up to 4 PVC or Virtual Networks 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers 1
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1
 11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type 1
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1
15 GUI for Web configuration User friendly GUI for Web configuration 1
16 Downloadable flash software updates Downloadable flash software updates
17 System statistics and monitoring System statistics and monitoring 1
18 Web Based Management (WBM) Web Based Management (WBM) 1
19 TR-069 WAN management protocol TR-069 WAN management protocol 1
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps

1 Hardware and Software version Hardware and Software version for each CPE 1
2 Duration of Standard Support Duration of standard support reference 1
3 Duration of Extended Support Duration of Extended Support 1
4 End of Life (Date) End of Life Date 1

SECTION TOTAL 20 0

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be pre-

3.17 configured on test units to be provided with offer

The following general parameters are specific to Telecom

3.17.1 Namibia and must be pre-configured onto the CPE by the
supplier:
1 Language: English (South Africa) Language: English (South Africa) 1
2 Country: Namibia Country: Namibia 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69
6 Status: Enabled 1

Pre- Configuration Parameters Supported for ADSL CPE.

3.17.2 Must be pre-configured on test units to be provided
with offer
Internet
1 VPI/VCI 0/35 1
2 Mode Routing 1
3 Connection type PPPOE 1
4 PPP Username "Unique. To be entered manually." No Pre-configuring 1
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring 1
required
6 Connection trigger Always On 1
VOIP
7 VPI/VCI 1/35 1
8 Connection type DHCP (IPoE) 1
9 Connection trigger Always On 1
10 IP protocol version IPv4 1
TR-069
11 VPI/VCI 8/35 1
12 Connection type DHCP (IPoE) 1
13 Connection trigger Always On 1
14 IP protocol version IPv4 1

Pre- Configuration Parameters Supported for VDSL CPE.

3.17.3 Must be pre-configured on test units to be provided
with offer
Internet
1 VLAN ID 200 1
2 Connection type PPPOE 1
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required 1

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required 1

5 Connection trigger Always On 1

6 IP protocol version IPv4 1
VOIP
7 VLAN ID 100 1
8 Connection type DHCP (IPoE) 1
9 Connection trigger Always On 1
10 IP protocol version IPv4 1
TR-069
11 VLAN ID 800 1
12 Connection type DHCP (IPoE) 1
13 Connection trigger Always On 1
14 IP protocol version IPv4 1

The following parameters must be pre-configured for

3.17.4 WIMAX or FTTH (WAN Ethernet) implementation

Internet
1 VLAN ID 200 1
2 Connection type PPPOE
"Unique. To be entered manually." No Pre-configuring
3 PPP Username required 1

"Unique. To be entered manually." No Pre-configuring

4 PPP Password required 1

"Unique. To be entered manually." No Pre-configuring

Bandwidth (uplink & downlink) required but modifiable by user via GUI 1

5 Connection trigger Always On 1

6 IP protocol version IPv4 1
VOIP
7 VLAN ID 100 1
8 Connection type DHCP (IPoE) 1
9 Connection trigger Always On 1
10 IP protocol version IPv4 1
TR-069
 11 VLAN ID 800 1
12 Connection type DHCP (IPoE) 1
13 Connection trigger Always On 1
14 IP protocol version IPv4 1

The following parameters must be pre-configured for

3.17.5 TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection 1

2 Mode Routing 1
3 Connection type DHCP 1
4 Connection trigger Always On 1
5 IP protocol version IPv4 1
6 NAT Enable Enable 1
DSCP Flags for VoIP
7 sip_prio 26 1
8 rtp_prio 46 1
9 rtcp_prio 46 1

Pre- Configuration Parameters Supported for VSAT CPE.

3.17.6 Must be pre-configured on test units to be provided
with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for analogue

3.17.7 Fax implementation (Voice CPE)
Fax Mode T.38 support for Fax 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates and
1 Upgrades for free 1

2 Are SW versions backward compatable within 1

SECTION TOTAL 60 0
6.19 Additional Features and Functionality SCORE supplier
TR-369 1
Others 1
Accessories that support CPE on offer
Wi-Fi extender / repeaters 5
Iot switches 1
Ethernet over power line adapter 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1
Lead Time
8 weeks delivery 1
13 0

5% General Requirements (5%) 0.00

23% Mandatory Requirements: Technical 0.00 98% PASS RATE REQUIRED
Standards (23%)
only WPA3 is not
20% Mandatory Requirements 2: Interfaces (20%) 0.00 79.2% PASS RATE REQU mandatory

20% Mandatory Requirements 3:Telephony Support (20%) 0.00

15% Mandatory Requirements 4: Other features 0.00

(15%)
15% Mandatory Requirements 5: Pre-configuration 0.00
parameters (20%)
2% Additional Features and Functionality (2%) 0.00

OVERALL SCORE 0.0

FINAL SCORE 0
 Bid Evalaution Score Sheet - Hybrid A- Fiber + Wireless Acess
Bid Name
Bid Number
CPE MODEL Hybrid A: Fiber + Wireless Acess

EVALUATION CRITERIA

Supplier
3.1 General Requirements (5%) Description Score Supplier Comment

The equipment should comply with operations from an AC mains

3.1.1 Power Supply voltage, 230V and frequency 50 Hz. Power plug should be Type D 1 1
or Type M, Alternatively TN will also consider Type C and Type N

Tenderers should indicate what surge protection the specific CPE

3.1.2 Voltage Protection has on board. Alternatively a surge protection accessory can be 1 1
recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1 1

3.1.4
The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory Authority 1 1
of Namibia (CRAN) if the Tender is successful.
b) Safety CPE must comply with IEC 60950-1 safety standards 1 1
3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1 1

SECTION TOTAL 6 6

Mandatory Requirements: Technical

OVERALL SECTION Score Supplier Comment
Standards (23%)
3.2 ADSL (Mobile CPE is an exception) Description Score Supplier Comment

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards G.984.1
3.3.1 ITU-T G.984 to G.984.4 1 1

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements of
1 ITU-T Rec. G.984.1 business and residential services and covers systems with 1 1
nominal line rates of 2.488 Gbit/s in the downstream direction
and 1.244 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical Media

2 ITU-T Rec. G.984.2 Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and 2488.320

Mbit/s in the downstream direction and 155.520 Mbit/s, 622.080
3 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s in the upstream 1 1
direction

Specifies the transmission convergence layer for gigabit-capable

4 ITU-T Rec. G.984.3 passive optical networks 1 1

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in 1 1
Recommendations ITU-T G.984.2 and G.984.3.
6
5.00 5.00

3.3.2 802.11 (All CPE Models) Description Score Supplier Comment

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1 1

Used for transmission over short distances at up to 54-Mbps in

3 IEEE 802.11g the 2.4 GHz bands 1 1

an extension which adds MIMO. The additional antenna allow for

4 IEEE 802.11n increased data throughput through spatial multiplexing and 1 1
increased range. Provides up to 100 Mbps transmission speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps in
5 IEEE 802.11ac a three antenna design 1 1

6 IEEE 802.11ax 0.50 0.50

Minimun score for this sub section is 5 5.5 5.5

3.4 802.3 (All CPE Models) Description Score Supplier Comment

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1 1

4 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1 1

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1 1

Certification compliance
BBF.247 certification compliance. Conformance to TR-156 and
Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1 1
standards for interoperable implementations

Interoperability with GPON OLT's from DSAN Zhone Telecom Namibia have two OLT vendors namely: Huawei and
and Huawei DSAN Zhone. The vendor is responsible to ensure that any 1 1
software adaptation to ensure interoperatibilty at their own cost

3.6 3G/4G ( Mobile and FMC Models)

All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G LTE 1 1
signal strength becomes low.
 All FMC CPEs must have a fixed broadband (ADSL, VDSL, WiMAX,
2 FMC TD-LTE) Ethernet WAN connection which will provide fail-safe 1 1
connectivity for mobile broadband access.
4G support must allow automatic 3G fallback if/when 4G signal
3 3G Fallback for 4G supported devices strength becomes low. 1 1

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps to

4 Supported Data rates be supported

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps 1 1

b) LTE Downlink Up to 100 Mbps downlink The CPE must provide a downlink connection of up to 100 Mbps 1 1

The 900 MHz and 2100MHz frequency must be supported for 3G

5 Frequency support for 3G Connectivity 1 1

6 Frequency support for 4G The 1800 MHz frequency must be supported for 4G connectivity 1 1

The 2300 MHz frequency and Band 40 must be supported for TD-
7 Frequency support for TD LTE & WTTX LTE & WTTX connectivity 1 1

The 2600 MHz frequency and Band 41 must be supported for TD-
8 Frequency support for TD LTE & WTTX LTE & WTTX connectivity 1 1

Please note that For TD-LTE & WTTX, the CPE need to be enabled
for us to lock it via Selected Band, Frequency and Physical ID. 1 1
a)
It will be good if the above mentioned functionality will be
enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to 1 1
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will support

the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the 1 1
Routers interface and to lock it via Selected Band, Frequency and
Physical ID
c)

18.00 18.00
SECTION TOTAL 28.5 28.5

3.7 Mandatory Requirements 2 (20%) Description Score Supplier Comment

CPE Interfaces
1 RJ-45 10/100 /1000 LAN Ports 1 1
2 RJ-45 10/100/1000 WAN Ports 1 1

Telephony Support (Voice enabled CPE) Interfaces

3 RJ-11 FXS Ports For analogue phones or for Fax. 1 1

4 RJ-45 Ports For ISDN BRI/PRI
5 DECT Digital Enhanced Cordless Communication 1 1

GPON and AE Interfaces

6 SC/APC connector GPON ONT Fibre Port 1 1
7 SC/UPC connector Active Ethernet ONT Fibre Port

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1 1
2 Wi-Fi Protected Access (WPA,WPA2) Wi-Fi Protected Access (WPA,WPA2) Security 1 1
Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5 5
3 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image management,

1 TR-069 Management Support Status and performance monitoring and Diagnostics 1 1

Auto-configuration and dynamic service provisioning 1 1

The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1 1

The CPE shall support both in-band and out-of-band

3 management. 1 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1 1
Control when clients or PC's connected to the device are allowed
2 Block MAC Address to access the internet 1 1

3.12 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1 1

SECTION TOTAL 25 25 0.8

Telephony Support

Mandatory Requirements 3 (20%) Description Score Supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated)

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1 1

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1 1
3 Echo Cancellation Echo Cancellation 1 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1 1
5 T.38 Support T.38 support for Fax 1 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1 1
7 Out of Band DTMF event Out of Band DTMF event 1 1

Telephony Support (Voice enabled CPE) General

3.14.3 Features
1 Digit Map Digit Map 1 1
2 Multi SIP Accounts Multi SIP Accounts 1 1
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support
 4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call
2 Call Parking Call Parking
3 Message Waiting Indicator Message Waiting Indicator
4 Hot Line Calling Hot Line Calling
5 Music on Hold Music on Hold
6 Anonymous Call Blocking Anonymous Call Blocking
7 Call Block and Filter Call Block and Filter
8 Call Forwarding -- Always Call Forwarding -- Always
9 Call Forwarding -- Busy Call Forwarding -- Busy
10 Call Forwarding -- No Answer Call Forwarding -- No Answer
11 Call Forwarding -- Follow me Call Forwarding -- Follow me
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable
14 Call History Call History
15 Call Hold Call Hold
16 Call ID (Proxy Support) Call ID (Proxy Support)
17 Caller ID Blocking Caller ID Blocking
18 Do Not Disturb Do Not Disturb
19 Cal Back on Busy Cal Back on Busy
20 Direct Inward Dialing Direct Inward Dialing
21 Line Hunting Line Hunting

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1 1
2 TCP/IP TCP/IP 1 1
3 UDP UDP 1 1
4 ICMP ICMP 1 1
5 DNS DNS 1 1
6 DDNS DDNS 1 1
7 DHCP DHCP 1 1
8 IGMP IGMP 1 1
9 FTP FTP 1 1
10 QoS QoS 1 1

SECTION TOTAL 20 20

Mandatory Requirements 4 (15%) Description Score supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1 1

4 IEEE 802.1q IEEE 802.1q 1 1
5 port-based VLAN port-based VLAN 1 1
6 Guest Networks Separate and secure network for guest users 1 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers 1 1
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type 1 1
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1 1
15 GUI for Web configuration User friendly GUI for Web configuration
16 Downloadable flash software updates Downloadable flash software updates 1 1
17 System statistics and monitoring System statistics and monitoring 1 1
18 Web Based Management (WBM) Web Based Management (WBM) 1 1
19 TR-069 WAN management protocol TR-069 WAN management protocol
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps 1 1

1 Hardware and Software version Hardware and Software version for each CPE 1 1
2 Duration of Standard Support Duration of standard support reference 1 1
3 Duration of Extended Support Duration of Extended Support 1 1
4 End of Life (Date) End of Life Date

SECTION TOTAL 20 20

Mandatory Requirements 5 (20%) Description Score supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto 1 1
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1 1
2 Country: Namibia Country: Namibia 1 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69 1
6 Status: Enabled

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP N/A
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
14 IP protocol version IPv4 N/A
N/A
Pre- Configuration Parameters Supported for VDSL
3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet N/A
1 VLAN ID 200 N/A
 2 Connection type PPPOE N/A

3 PPP Username "Unique. To be entered manually." No Pre-configuring required N/A

4 PPP Password "Unique. To be entered manually." No Pre-configuring required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
7 IP protocol version IPv6 N/A
VOIP N/A
8 VLAN ID 100 N/A
9 Connection type DHCP (IPoE) N/A
10 Connection trigger Always On N/A
11 IP protocol version IPv4 N/A
N/A
TR-069 N/A
12 VLAN ID 800 N/A
13 Connection type DHCP (IPoE) N/A
14 Connection trigger Always On N/A
15 IP protocol version IPv4 N/A
16 IP protocol version IPv6 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet 1 1
1 VLAN ID 200
2 Connection type PPPOE 1 1
"Unique. To be entered manually." No Pre-configuring required
3 PPP Username but modifiable by user via GUI 1 1

"Unique. To be entered manually." No Pre-configuring required

4 PPP Password but modifiable by user via GUI 1 1

"Unique. To be entered manually." No Pre-configuring required

5 Bandwidth (uplink & downlink but modifiable by user via GUI 1 1

6 Connection trigger Always On 1 1

7 IP protocol version IPv4 1 1
8 IP protocol version IPv6 1 1
VOIP 1 1
9 VLAN ID 100 1 1
10 Connection type DHCP (IPoE) 1 1
11 Connection trigger Always On 1 1
12 IP protocol version IPv4
13 IP protocol version IPv6
TR-069 1 1
13 VLAN ID 800 1 1
14 Connection type DHCP (IPoE) 1 1
15 Connection trigger Always On 1 1
16 IP protocol version IPv4 1 1
17 IP protocol version IPv6 1 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection 1 1

2 Mode Routing 1 1
3 Connection type DHCP 1 1
4 Connection trigger Always On 1 1
5 IP protocol version IPv4 1 1
6 IP protocol version IPv5 1 1
7 NAT Enable Enable 1 1
DSCP Flags for VoIP
8 sip_prio 26 1 1
9 rtp_prio 46 1 1
10 rtcp_prio 46 1 1

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A N/A
3 Management: TBD Management: TBD N/A N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Codec: G.711 A-Law Codec: G.711 A-Law 1 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1 1

2 Are SW versions backward compatable within 1 1

SECTION TOTAL 37 37

6.19 Additional Features and Functionality (2%) Description Score supplier Comment
TR-369 1 1
Others 1 1
Accessories that support CPE on offer
Wi-Fi extender / repeaters 5 5
Iot switches 1 1
Ethernet over power line adapter 3 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1 1

Lead Time
8 weeks delivery 1 1
SECTION TOTAL 13 13

5% General Requirements (5%) 5

23% Mandatory Requirements: Technical 23 91% PASS RATE REQUIRAll techincal standards must be passed, with exception of the DSAN & Huawei OLT interoperability
Standards (23%)
Only WPA3 is not
20% Mandatory Requirements 2: Interfaces 20 80% PASS RATE REQUIR mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 20

15% Mandatory Requirements 4: Other 15

features (15%)
15% Mandatory Requirements 5: Pre- 15
configuration parameters (20%)
2% Additional Features and Functionality (2%) 2

OVERALL SCORE 100.00

FINAL SCORE 60
 Bid Evalaution Score Sheet - Hybrid A- Fiber + Wireless Acess
Bid Name
Bid Number
CPE MODEL Hybrid A: Fiber + Wireless Acess

EVALUATION CRITERIA

3.1 General Requirements (5%) Description SCORE Supplier Comment

The equipment should comply with operations from an AC mains

3.1.1 Power Supply voltage, 230V and frequency 50 Hz. Power plug should be Type D 1
or Type M, Alternatively TN will also consider Type C and Type N

Tenderers should indicate what surge protection the specific CPE

3.1.2 Voltage Protection has on board. Alternatively a surge protection accessory can be 1
recommended.
The CPE will be marked with the suppliers name/id mark and
3.1.3 Identification of Equipment equipment model/type reference 1

3.1.4
The Tenderer shall ensure that the CPE offered pass the type
a) Type Approval approval process with the Communication Regulatory Authority 1
of Namibia (CRAN) if the Tender is successful.
b) Safety CPE must comply with IEC 60950-1 safety standards 1
3.1.5 Electromagnetic Compatibility CPE Shall comply with IEC CISPR 22 for radio interference 1

SECTION TOTAL 6 0

Mandatory Requirements: Technical

Description SCORE supplier Comment Column2 Column3
Standards (23%)

3.2 ADSL (Mobile CPE is an exception)

3.2.1

1 ITU-T Rec. G992.1 Annex A Asymmetric digital subscriber line (ADSL) transceivers N/A

2 ITU-T Rec. 992.3 Annex A Asymmetric digital subscriber line 2 (ADSL2) transceivers N/A

Asymmetric digital subscriber line 2 (ADSL2) transceivers –

3 ITU-T Rec. 992.5 Annexure M Extended bandwidth ADSL2 (ADSL2plus) N/A

3.2.2 VDSL (Mobile CPE is an exception)

1 ITU-T Rec. 993.1 Very high speed digital subscriber line (VDSL) transceivers N/A

2 ITU.T Rec. 993.2 Very high speed digital subscriber line 2 (VDSL2) transceivers N/A

3 ITU.T Rec. 993.5 Self-FEXT (far-end crosstalk) cancellation (vectoring) N/A

3.2.3 xDSL (Mobile CPE is an exception)

ITU-T Rec. 994.1 Handshake Procedure for digital subscriber line transceivers N/A

3.3 ITU-T G.984: GPON

GPON CPEs must comply with the ITU-T GPON standards G.984.1
3.3.1 ITU-T G.984 to G.984.4 N/A

General characteristics for GPON - flexible optical fibre access

network capable of supporting the bandwidth requirements of
1 ITU-T Rec. G.984.1 business and residential services and covers systems with N/A
nominal line rates of 2.488 Gbit/s in the downstream direction
and 1.244 Gbit/s in the upstream direction.

Gigabit-capable Passive Optical Networks (GPON): Physical Media

2 ITU-T Rec. G.984.2 Dependent (PMD) layer specification.

GPON with nominal line rates of 1244.160 Mbit/s and 2488.320

Mbit/s in the downstream direction and 155.520 Mbit/s, 622.080
3 Mbit/s, 1244.160 Mbit/s and 2488.320 Mbit/s in the upstream N/A
direction

Specifies the transmission convergence layer for gigabit-capable

4 ITU-T Rec. G.984.3 passive optical networks N/A

provides the optical network termination (ONT) management

and control interface (OMCI) specification for gigabit-capable
5 ITU-T Rec. G.984.4 passive optical network (G-PON) systems as defined in N/A
Recommendations ITU-T G.984.2 and G.984.3.
6

3.3.2 802.11 (All CPE Models)

Provides up to 54-Mbps in the 5 GHz band. Uses an OFDM
1 IEEE 802.11a encoding rather than FHSS/DSSS 1

2 IEEE 802.11b Provides up to 11-Mbps in the 2.4 GHz band. Uses DSSS Only. 1

Used for transmission over short distances at up to 54-Mbps in

3 IEEE 802.11g the 2.4 GHz bands 1

an extension which adds MIMO. The additional antenna allow for

4 IEEE 802.11n increased data throughput through spatial multiplexing and 1
increased range. Provides up to 100 Mbps transmission speeds.

Deliver data rates of 433 Mbps per spatial stream or 1.3 Gbps in
5 IEEE 802.11ac a three antenna design 1

6 IEEE 802.11ax 0.50

Minimun score for this sub section is 5 5.5 0.0

3.4 802.3 (All CPE Models) SCORE supplier

1 IEEE 802.3i 10BASE-T 10 Mbit/s (1.25 Mbit/) over twisted pair 1
100BASE-TX, 100BASE-T4, 100BASE-FX Fast Ethernet at 100
2 IEEE 802.3u Mbit/s (12.5 Mbit/s) with auto negotiation 1

3 IEEE 802.3x Full Duplex and flow control, also incorporates DIX framing 1
Ethernet Link OAM (EFM OAM) - Link layer connectivity
4 IEEE 802.3ah management between PE and CE, Link layer monitoring, UNI 1
status

3.5 802.1 (All CPE Models)

Standard for local and metropolitan networks -- Media access

IEEE 802.1q control bridges and virtual bridged local area networks 1

Certification compliance
BBF.247 certification compliance. Conformance to TR-156 and
Broadband Forum certification BBF.247 TR-280 using OMCI as defined in the ITU G.988 which is critical 1
standards for interoperable implementations

Interoperability with GPON OLT's from DSAN Zhone Telecom Namibia have two OLT vendors namely: Huawei and
and Huawei DSAN Zhone. The vendor is responsible to ensure that any
software adaptation to ensure interoperatibilty at their own cost

DSAN ZHONE 1
HUAWEI MSAN VERSION 1
3.6 3G/4G ( Mobile and FMC Models)
All CPEs must support dual-bands 3G (UMTS) and 4G (LTE). 3G
1 3G/4G Dual Band Support support must allow automatic 3G fall-back if or when the 4G LTE 1
signal strength becomes low.

All FMC CPEs must have a fixed broadband (ADSL, VDSL, WiMAX,
2 FMC TD-LTE) Ethernet WAN connection which will provide fail-safe 1
connectivity for mobile broadband access.
4G support must allow automatic 3G fallback if/when 4G signal
3 3G Fallback for 4G supported devices strength becomes low. 1

LTE uplink: Up to 50 Mbps, and LTE downlink: Up to 100 Mbps to

4 Supported Data rates be supported

a) LTE Uplinkg Up to 50 Mbps uplink The CPE must provide an uplink connection of up to 50 Mbps 1

b) LTE Downlink Up to 100 Mbps downlink The CPE must provide a downlink connection of up to 100 Mbps 1

The 900 MHz and 2100MHz frequency must be supported for 3G

5 Frequency support for 3G Connectivity 1

6 Frequency support for 4G The 1800 MHz frequency must be supported for 4G connectivity 1

The 2300 MHz frequency and Band 40 must be supported for TD-
7 Frequency support for TD LTE & WTTX LTE & WTTX connectivity 1

The 2600 MHz frequency and Band 41 must be supported for TD-
8 Frequency support for TD LTE & WTTX LTE & WTTX connectivity 1

Please note that For TD-LTE & WTTX, the CPE need to be enabled
for us to lock it via Selected Band, Frequency and Physical ID. 1
a)
It will be good if the above mentioned functionality will be
enabled automatically or if you can give us the Super User
Password for us to control the Routers on TDD-LTE & WTTX to 1
lock it via Selected Band, Frequency and Physical ID.
b)

Please note that capability/functionality the Routers will support

the above mentioned Frequency as per their current
specifications but they will connect to any available network
within that Frequency. We want to be able to logon to the 1
Routers interface and to lock it via Selected Band, Frequency and
Physical ID
c)

20.00 0.00
SECTION TOTAL 25.50 0.00

3.7 Mandatory Requirements 2 (20%) Description SCORE supplier Comment

CPE Interfaces
1 RJ-45 10/100 /1000 LAN Ports 1
2 RJ-45 10/100/1000 WAN Ports 1

Telephony Support (Voice enabled CPE) Interfaces

3 RJ-11 FXS Ports For analogue phones or for Fax. 1

4 RJ-45 Ports For ISDN BRI/PRI
5 DECT Digital Enhanced Cordless Communication 1

GPON and AE Interfaces

6 SC/APC connector GPON ONT Fibre Port
7 SC/UPC connector Active Ethernet ONT Fibre Port 1

3.8 Security Features

1 WEP (64/128 bits) Wireless Equivalent Privacy Security 1
2 Wi-Fi Protected Access (WPA,WPA2, WPA3) Wi-Fi Protected Access (WPA,WPA2, WPA3) Security 1
3 Wi-Fi Protected Access (WPA3) Wi-Fi Protected Access (WPA3) Security 5
4 Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1

Firewall Features
4 Network Address Translation (NAT) Network Address Translation (NAT) 1
5 Stateful Packet Inspection (SPI) Stateful Packet Inspection (SPI) 1

6 VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec VPN Pass-through/Multi-sessions PPTP/L2TP/Ipsec 1

3.9 Demarcation Zone

DMZ IP address for a single host on the LAN DMZ IP address for a single host on the LAN 1

3.1 CPE WAN Management Protocol (CWMP)

TR-069 should include Software/firmware image management,

1 TR-069 Management Support Status and performance monitoring and Diagnostics 1

Auto-configuration and dynamic service provisioning 1

The CPE shall be TR-069 enabled and be able to support a 3rd
2 party ACS 1

The CPE shall support both in-band and out-of-band

3 management. 1

3.11 Access Control

1 Block Website Create a lis of Websites which must not be accessed 1
Control when clients or PC's connected to the device are allowed
2 Block MAC Address to access the internet 1

3.12 Port Forwarding

The user should be able to open this ports on the CPE and
1 Range (e.g. 50-100) redirect data through this ports to a single PC on the LAN 1

The user should be able to open this ports on the CPE and
2 Individual (e.g. 80, 68, 888) redirect data through this ports to a single PC on the LAN 1

SECTION TOTAL 25 0

Telephony Support

Mandatory Requirements 3 (20%) Description SCORE supplier Comment

3.14 Telephony Support

3.14.1 Interfaces supported by all voice enabled CPE:

1 RJ-11 FXS Analogue phone or Fax Ports RJ-11 FXS Analogue phone or Fax Ports 1
2 RJ-45 for ISDN BRI/PRI Ports RJ-45 for ISDN BRI/PRI Ports
3 DECT support (where indicated) DECT support (where indicated) 1

Telephony Support (Voice enabled CPE) Telephone

3.14.2 Features

1 Signalling Protocols: SIP Signalling Protocols: SIP 1

2 Codec: G.711 A-Law, G.729, G.723, G.726 Codec: G.711 A-Law, G.729, G.723, G.727 1
3 Echo Cancellation Echo Cancellation 1
4 Voice Activity Detection for G.711/723/729 Voice Activity Detection for G.711/723/730 1
5 T.38 Support T.38 support for Fax 1
6 Comfort Noise Generation for G.711/723/729 Comfort Noise Generation for G.711/723/730 1
7 Out of Band DTMF event Out of Band DTMF event 1
 Telephony Support (Voice enabled CPE) General
3.14.3 Features
1 Digit Map Digit Map 1
2 Multi SIP Accounts Multi SIP Accounts 1
Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP
3 Support Direct Ip-to-Ip Call without SIP Proxy (P2P and RTP Support

4 Call Pick Up Call Pick Up (where PABX support is required)

5 Call Transfer Call Transfer (Proxy Support) Where PABX support is required

Telephony Support (Voice enabled CPE) Optional

3.14.4 General Features
1 3 Party Call 3 Party Call
2 Call Parking Call Parking
3 Message Waiting Indicator Message Waiting Indicator
4 Hot Line Calling Hot Line Calling
5 Music on Hold Music on Hold
6 Anonymous Call Blocking Anonymous Call Blocking
7 Call Block and Filter Call Block and Filter
8 Call Forwarding -- Always Call Forwarding -- Always
9 Call Forwarding -- Busy Call Forwarding -- Busy
10 Call Forwarding -- No Answer Call Forwarding -- No Answer
11 Call Forwarding -- Follow me Call Forwarding -- Follow me
12 Call Forwarding -- Unconditional Call Forwarding -- Unconditional
13 Call Forwarding -- Unavailable Call Forwarding -- Unavailable
14 Call History Call History
15 Call Hold Call Hold
16 Call ID (Proxy Support) Call ID (Proxy Support)
17 Caller ID Blocking Caller ID Blocking
18 Do Not Disturb Do Not Disturb
19 Cal Back on Busy Cal Back on Busy
20 Direct Inward Dialing Direct Inward Dialing
21 Line Hunting Line Hunting

6.14.5 Other Features

6.14.5.1 Other Protocols that must be Supported
1 IP Routing (v4/v6) IP Routing (v4/v6) 1
2 TCP/IP TCP/IP 1
3 UDP UDP 1
4 ICMP ICMP 1
5 DNS DNS 1
6 DDNS DDNS 1
7 DHCP DHCP 1
8 IGMP IGMP 1
9 FTP FTP 1
10 QoS QoS 1

SECTION TOTAL 21 0

Mandatory Requirements 4 (15%) Description SCORE supplier Comment

3.14.5.2 Other Features Supported
1 Firmware upgrade via web-based UI & TR-069 Firmware upgrade vai web-based UI & TR-069 1
File server for Network Attached Storage (NAS)
2 Devices File server for Network Attached Storage (NAS) Devices

3 Web Filtering Web Filtering 1

4 IEEE 802.1q IEEE 802.1q 1
5 port-based VLAN port-based VLAN 1
6 Guest Networks Separate and secure network for guest users 1
7 Up to 4 Virtual Networks Up to 4Virtual Networks 1
8 Up to 4 PPPoE sessions Up to 4 PPPoE sessions 1
9 0 to 255 virtual path identifiers 0 to 255 virtual path identifiers 1
10 PPPoE (Interface Protocol) Connection Type PPPoE (Interface Protocol) Connection Type 1
11 PPPoA (Interface Protocol) Connection Type PPPoA (Interface Protocol) Connection Type 1
12 Dynamic IP (Interface Protocol) Connection Type Dynamic IP (Interface Protocol) Connection Type 1
13 Static IP (Interface Protocol) Connection Type Static IP (Interface Protocol) Connection Type 1
14 Bridge (Interface Protocol) Connection Type Bridge (Interface Protocol) Connection Type 1
15 GUI for Web configuration User friendly GUI for Web configuration
16 Downloadable flash software updates Downloadable flash software updates 1
17 System statistics and monitoring System statistics and monitoring 1
18 Web Based Management (WBM) Web Based Management (WBM) 1
19 TR-069 WAN management protocol TR-069 WAN management protocol
20 Command Line Interface (CLI) Command Line Interface (CLI)

3.16 Product Roadmaps 1

1 Hardware and Software version Hardware and Software version for each CPE 1
2 Duration of Standard Support Duration of standard support reference 1
3 Duration of Extended Support Duration of Extended Support 1
4 End of Life (Date) End of Life Date

SECTION TOTAL 20 0

Mandatory Requirements 5 (20%) Description SCORE supplier Comment

Pre- Configuration Parameters Supported. Must be
3.17 pre-configured on test units to be provided with
offer

The following general parameters are specific to

3.17.1 Telecom Namibia and must be pre-configured onto 1
the CPE by the supplier:
1 Language: English (South Africa) Language: English (South Africa) 1
2 Country: Namibia Country: Namibia 1
3 Time Zone: (UCT +02:00) Windhoek Time Zone: (UCT +02:00) Windhoek 1
4 Country Code (for telephony): 264 Country Code (for telephony): 264 1
5 ACS settings: Server URL 1
http://acs.telecom.na:9675/tn/CPEManager/CPEs/Auth_Basic/genericTR69
6 Status: Enabled

Pre- Configuration Parameters Supported for ADSL

3.17.2 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VPI/VCI 0/35 N/A
2 Mode Routing N/A
3 Connection type PPPOE N/A
4 PPP Username "Unique. To be entered manually." No Pre-configuring N/A
required
5 PPP Password "Unique. To be entered manually." No Pre-configuring N/A
required
6 Connection trigger Always On N/A
VOIP N/A
7 VPI/VCI 1/35 N/A
8 Connection type DHCP (IPoE) N/A
9 Connection trigger Always On N/A
10 IP protocol version IPv4 N/A
TR-069 N/A
11 VPI/VCI 8/35 N/A
12 Connection type DHCP (IPoE) N/A
13 Connection trigger Always On N/A
 14 IP protocol version IPv4 N/A

Pre- Configuration Parameters Supported for VDSL

3.17.3 CPE. Must be pre-configured on test units to be
provided with offer
Internet
1 VLAN ID 200 N/A
2 Connection type PPPOE N/A

3 PPP Username "Unique. To be entered manually." No Pre-configuring required N/A

4 PPP Password "Unique. To be entered manually." No Pre-configuring required N/A

5 Connection trigger Always On N/A

6 IP protocol version IPv4 N/A
7 IP protocol version IPv6 N/A
VOIP N/A
8 VLAN ID 100 N/A
9 Connection type DHCP (IPoE) N/A
10 Connection trigger Always On N/A
11 IP protocol version IPv4 N/A
IP protocol version IPv6 N/A
TR-069 N/A
12 VLAN ID 800 N/A
13 Connection type DHCP (IPoE) N/A
14 Connection trigger Always On N/A
15 IP protocol version IPv4 N/A
IP protocol version IPv6 N/A

The following parameters must be pre-configured

3.17.4 for WIMAX or FTTH (WAN Ethernet)
implementation
Internet 1
1 VLAN ID 200
2 Connection type PPPOE 1
"Unique. To be entered manually." No Pre-configuring required
3 PPP Username but modifiable by user via GUI 1

"Unique. To be entered manually." No Pre-configuring required

4 PPP Password but modifiable by user via GUI 1

"Unique. To be entered manually." No Pre-configuring required

5 Bandwidth (uplink & downlink but modifiable by user via GUI 1

6 Connection trigger Always On 1

IP protocol version IPv4
7 VOIP 1
8 VLAN ID 100 1
9 Connection type DHCP (IPoE) 1
10 Connection trigger Always On 1
IP protocol version IPv4
11 TR-069 1
12 VLAN ID 800 1
13 Connection type DHCP (IPoE) 1
14 Connection trigger Always On 1
15 IP protocol version IPv4 1
15 IP protocol version IPv6 1

The following parameters must be pre-configured

3.17.5 for TD-LTE (WAN Ethernet) implementation:

1 Connection Internet connection via external modem Internet connection 1

2 Mode Routing 1
3 Connection type DHCP 1
4 Connection trigger Always On 1
5 IP protocol version IPv4 1
6 IP protocol version Ipv6 1
7 NAT Enable Enable 1
DSCP Flags for VoIP
7 sip_prio 26 1
8 rtp_prio 46 1
9 rtcp_prio 46 1

Pre- Configuration Parameters Supported for VSAT

3.17.6 CPE. Must be pre-configured on test units to be
provided with offer
1 Data: VLAN ID 24 Data: VLAN ID 24 N/A
2 Voice: VLAN ID 2668 Voice: VLAN ID 2668 N/A
3 Management: TBD Management: TBD N/A

Pre- Configuration Parameters Supported for

3.17.7 analogue Fax implementation (Voice CPE)
Codec: G.711 A-Law Codec: G.711 A-Law 1

3.18 Software Updates and Upgrades

Does the supplier offer all future Software Updates
1 and Upgrades for free 1

2 Are SW versions backward compatable within 1

SECTION TOTAL 35 0

6.19 Additional Features and Functionality (2%) Description SCORE supplier Comment
TR-369 1
Others 1

Accessories that support CPE on offer

Wi-Fi extender / repeaters 5
Iot switches 1
Ethernet over power line adapter 3
Wi-Fi Protected Setup (WPS) -- PIN/PBC Wi-Fi Protected Setup (WPS) -- PIN/PBC Security 1

Lead Time
8 weeks delivery 1
SECTION TOTAL 13 0

5% General Requirements (5%) 0

23% Mandatory Requirements: Technical 0 90% PASS RATE REQUIRAll techincal standards must be passed, with exception of the DSAN & Huawei ONT interoperability
Standards (23%)
Only WPA3 is not
20% Mandatory Requirements 2: Interfaces 0 80% PASS RATE REQUIR mandatory
(20%)
Mandatory Requirements 3:Telephony Support
20% (20%) 0

15% Mandatory Requirements 4: Other 0

features (15%)
15% Mandatory Requirements 5: Pre- 0
configuration parameters (20%)
2% Additional Features and Functionality (2%) 0

OVERALL SCORE 0.00

FINAL SCORE 0