CRP123/CRP129 Premium Quick Start Guide LAUNCH

CRP123/CRP129 Premium Handset 2. Register & Update

DB15 Connector Prerequisite conditions:

(To connect the diagnostic cable.) 1. Go to http://mycar.x431.com and click “Products” --> “CRP” -->
“CRP123/CRP129 Premium Updating Tool Download” to download
and install it on the computer.
2. System requirements: Windows XP, Windows 7, Windows 8,
DTC Lookup Button
Selection Button Windows 10 operating system.
(To retrieve the DTCs in
the database.) There are 2 methods available to update your tool. You may choose
one of the following to proceed.
OK Button
Method 1: Via TF Card
LCD Screen (To confirm an action or operation.)
1. Launch the update tool, a screen similar to Figure 1 will appear:
ESC Button 1
Select Language English
(To go back to the previous screen.)
Product Serial Number

TF Card Slot USB Port

Device Upgrade
(To insert the TF card.) (To connect the included USB cable.)
2. In Figure 1, type in the Product Serial Number (located at the back
of the tool).
1. Preparation & Connections Note: Once the Serial Number is entered, “Restore System” will become
activated, which is used to restore system if a new TF card is replaced.
3. Click [Device Upgrade] to jump to the registration page. Enter the
Note: To make sure the tool is running the latest available software, it is advisable to check for updates on a frequent following information and click [Submit] (refer to Figure 2).
basis. Refer to Section 2 “Register & Update” for details.
2
1. Preparation Your E-mail address:

1. Turn the vehicle ignition on. 2. Throttle should be in a closed position.

Confimr E-mail:
2. Vehicle Connection Note: Remember to remove the
1. Locate vehicle's DLC socket: The DLC (Data Link Connector or Diagnostic diagnostic cable from the DLC
Register Code:
if it remains unused.
Link Connector) is typically a standard 16-pin connector where diagnostic
code readers interface with a vehicle's on-board computer. It is usually Cancel Submit Exit
located 12 inches from the center of the steering wheel, under or around
the driver's side for most vehicles. (If you need the Register Code, please refer to steps 4~7.)
2. Connect the diagnostic cable into the vehicle's DLC socket. (If you have the Register Code, directly proceed to step 8.)
3. Plug the other end of diagnostic cable into the DB15 connector of the 4. The Register Code can be found in your tool. Connect one end of
handset and tighten the captive screws. DLC Location the supplied USB cord to your tool, and the other end on the
computer.
5. After the tool has powered up and entered the main menu screen,
move the highlight bar on the “Help” icon (See Figure 3) and press
Note: For more details on how to diagnose a vehicle, refer to the User Manual included in the package. [OK].

Pictures illustrated here are for reference purpose only and this Quick Start Guide is subject to change without notice.
CRP123/CRP129 Premium Quick Start Guide LAUNCH

2. Register & Update (Cont.) 2. Register & Update (Cont.)

10
3 4 Method 2: Via USB Cable
Help Boot Version: V10.02
Note: Make sure the PC has an Internet connection. Serial Number: XXXXXXXXXXXX
DLC Location Information Register Code: XXXXXXXXXXXX
1. Connect one end of the USB cable to the USB
DTC Library
port of PC, and the other end to the tool. Check for new version?
Abbreviation
2. If a newer version is found, a screen similar to Note: Internet connection is required for
Tool Information PC.
Figure 10 will appear.
About OBD 4
3. Press [OK] to configure this tool as a USB
device. See Figure 11. Yes – OKAY No – ESC
(Note: The Serial Number and Register Code shown
1/5
in this figure are needed for inputting in Steps 4-6.)
7. The Register Code shown in Figure 5 is the 4. Launch the update tool, a screen similar to 11
Register Code needed in step 3. 5 Figure 12 will appear. Boot Version: V10.02
Tool Information
(Return to step 3 and input the Register Code
12 Serial Number: XXXXXXXXXXXX
Boot version: V02.01 Select Language English Register Code: XXXXXXXXXXXX
and then proceed) Display program version: V02.00
Product Serial Number Caution:
8. Install the TF card from the tool into the Diagnostic program version: V10.50 DO NOT disconnect USB while downloading.
supplied USB TF card adaptor and insert Diagnostic library version: V02.24 Update
The unit should be re-powered after
download new version.
into the USB port of the computer. Serial Number: xxxxxxxxxxxx
9. Reopen the update tool, select the Register Code: 270025000247 5. Type in the Product Serial Number.
updates you would like to perform or - Exit 6. Click [Update] to jump to Figure 13. Input
click " Select All ", and then click the following information and click
6 14
[Download] to start downloading. Welcome Select Language [Submit] to enter the update page. Welcome Select Language
Chinese German
Chinese German
Product Serial Number Network Status: French Italian
See Figure 6. Product Serial Number Network Status: French Italian 13 965099000003 Input Flow: 0.0KB/s
English Russian
English Russian
965099000003 Input Flow: 0.0KB/s Your E-mail address: Spanish Portuguese
10.Once all steps are complete, Spanish Portuguese Select All Vehicle Coverage
Select All Vehicle Coverage

reinsert the TF card into the tool Software Name Latest Version Local Version Release Date
Software Name
CRP129 Firmware
Latest Version
V2.19
Local Version Release Date
2015-08-21
CRP129 Firmware V2.19 2015-08-21 ACURA V10.40 2015-09-11
and power the tool via USB cable ACURA V10.40 2015-09-11 Confimr E-mail: AUDI V11.20 2015-09-06
AUDI V11.20 2015-09-06 BENZ V11.30 2015-12-05
BENZ V11.30 2015-12-05 BMW V11.20 2015-08-26
or via OBD II cable. A dialog box BMW
CHRYSLER
V11.20
V11.51
2015-08-26
2015-05-27
CHRYSLER V11.51 2015-05-27
CITROEN V11.03 2015-07-13

(Note: If only diagnostic software is CITROEN V11.03 2015-07-13 Register Code: DAEWOO V11.11 2015-07-22
DAEWOO V11.11 2015-07-22 FIAT V10.12 2015-11-13
FIAT V10.12 2015-11-13 GM V12.02 2015-08-21
updated and no firmware package is GM
HONDA
V12.02
V11.31
2015-08-21
2015-09-11
HONDA
HYUNDAI
V11.31
V12.30
2015-09-11
2015-09-06
HYUNDAI V12.30 2015-09-06 INFINITI V10.40 2015-12-05
downloaded in Figure 6, this box will INFINITI V10.40 2015-12-05 Cancel Submit Exit JAGUAR V10.42 2015-08-26
JAGUAR V10.42 2015-08-26 JPISUZU V10.10 2015-05-27

not appear) prompting you to upgrade JPISUZU

KIA
V10.10
V12.00
2015-05-27
2015-07-13
KIA
LANCIA
V12.00
V11.30
2015-07-13
2015-07-22
LANCIA V11.30 2015-07-22
will pop up on the screen (See 7. Select the updates you would like to Status
Status
Figure 7 & Figure 8), select [OK]. Setup Status perform or click " Select All ", and then Setup Status

11.The registration process is now Total 9 Items Download Quit click [Download] to start downloading. Total 9 Items Download Quit

complete, your tool is now ready for See Figure 14.

use. See Figure 9. 8. Once all steps are complete, restart
7 8 9 your tool. It will prompt you to upgrade, 15 16
System upgrade System upgrade System upgrade System upgrade System upgrade
click [OK] to start updating. It may take
Sure upgrade? Downloading...... Upgrade Complete! several minutes to finish the update. Sure upgrade? Upgrade Complete!
5% 100% 100%
9. The update process is complete, your
tool is now ready for use.

   ：

： A4 ，1:1
 ，  

：，80g