DRAIN LINE SHALL BE AT LEAST CONICAL SPIN-IN FITTING

FLOOR ABOVE THE SAME SIZE AS THE NIPPLE Design

FRAMING ON THE DRAIN PAN. WITH DAMPER AND
CEILING EXHAUST FAN INSULATION GUARD
NOTE: MOUNTING BRACKETS SHALL
ACCEPTABLE SHEATHING CLEAN OUT
SCREENS AND RIVETS ON BE ADJUSTABLE TO ALLOW INSULATED FLEXIBLE DUCT R
DRYER DUCTING IS NOT FLUSH MOUNTING IN CEILING. WITH STAINLESS STEEL BAND
SECCONDARY MOISTURE EQUIPMENT
ALLOWED (TYPICAL)
PROTECTION BARRIER 15° MEP
PITCH DOWN
TOWARD DRAIN. GREEN
FASTENERSET IN SEALANT SEE PLAN FOR
FAN TO BE FURNISHED WITH DESIGN
BACKDRAFT DAMPER AIR FLOW DUCT SIZE
SET FLANGE IN SEALANT A & BUILD
CLEAN OUT
DRYER VENT DRAIN PAN INSULATION
SHEETMETAL DUCT
HANGER RODS SUPPORTED DUCTWORK WITH FAST AND ACCURATE
FROM STRUCTURE ABOVE B
PLAN OR SIDE VIEW PLAN OR SIDE VIEW INTERNAL LINING
CEILING
SEALANT AT PERMETER OF

1"
PENETRAITION DUCT TRANSITION DUCT TRANSITION
FLEXIBLE DUCT UNIT TYPE A B
MAY 29, 2025
WITH EQUIPMENT IN DUCT DRAW THRU X+1" X/2 +.5"
FASTENER THROUGH NYLON OPEN SITE DRAIN OR CEILING DIFFUSER
APPROVED RECEPTOR BLOW THRU .5" X +.75" ESS
PROF IONAL
SLEEVE CEILING NOTE: UNLESS OTHERWISE INDICATED ON PLANS, ED DUC
NOTE:

TER
NG

EN
WHERE X = STATIC PRESS. IN PAN

G IN
MAXIMUM ANGLES SHOWN SHALL APPLY. No.

REGIS
DU
FLEXIBLE DUCT INSULATION SHALL BE TAPED TO MAIN DUCT AND

V
PERFORATED METAL GRILLE NOTES:

EER
CEMENT BOARD M37777
BACKDRAFT FURNISHED WITH FAN 1. COIL MUST BE MOUNTED HIGH ENOUGH TO PERMIT TRAP TO BE INSTALLED. TO BACK OF CEILING DIFFUSER. INSULATION SHALL COVER SPIN-IN EXP. DATE
DAMPER 2. PROVIDE SHIMS OR STRUCTURAL PLATFORMS REQUIRED TO ELEVATE FACTORY FITTING AND FLUSH WITH THE BACK OF DIFFUSER. 03/31/26
PACKAGED AIR HANDLING UNITS TO OBTAIN REQUIRED TRAP HEIGHT. M L
E C HA N I C A
ST I

A
AT
E OF L I FORN
CA

DRYER WALL CAP DETAIL CEILING EXHAUST FAN DETAIL DUCT TRANSITION DETAIL AIR HANDLING UNIT DRAIN TRAP DETAIL FLEXIBLE DUCT CONNECTION DETAIL
10 8 5 4 11

FLOOR/CEILING ASSEMBLIES NOTE:

FRESH
M 1 1/2-5 TONS CONDENSING UNIT
AIR
- THREE (3) FEET CLEARANCE MUST BE PROVIDED IN FRONT OF THE CONTROL BOX

RESIDENCE
(ACCESS PANELS) AND ANY OTHER SIDE REQUIRING SERVICE.
- POSITION THE OUTDOOR UNIT A MINIMUM OF 12" FROM ANY WALL OR
SURROUNDING SHRUBBERY TO ENSURE ADEQUATE AIRFLOW. METAL FASTENERS :

NEWPORT BEACH, CA 92663

- TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100" MINIMUM. UNIT
OMARK INSUL-PINS, DURA DYNE FASTENERS OR GRIP NAILS. 1" DUCT LINER

BALBOA
SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES NOT POUR DIRECTLY ON UNIT
NONE RATED DROOPED CEILING GRIP NAILS SHALL BE INSTALLED BY "GRIP NAIL

1509 W. BALBOA BLVD,

RETURN AIR SUPPLY AIR
CEILING AIR HAMMER" OR BY AUTOMATIC FASTENER EQUIP.
TOP AND BOTTOM
ELECTRICAL DISCONNECT
1" DUCT LINER SECTION OF LAPPED & BUTTED
MOUNTED 30" HIGH
FRONTSERVC
I ECLEARANCE CORNERS
LINER SHALL
2,3,4 tons : 21 INCHES
5 tons : 24 INCHES ON
OVERLAP THE
SIDES
OFF METAL FASTENERS UPPER LEVEL FLOOR
NOTE: EXTERIOR WALL
12" O.C. MAX.
- MOTORIZED DAMPER GALV. SHT.
FOR BELOW
INTERLOCK WITH SUPPLY FAN METAL DUCT
2500 FPM WALL LOUVER
VELOCITY PAINT TO
ALL ENDS OF LINER LINER TO BE MATCH WALL
NOT MORE THAN TO BE COATED WITH ADHERED TO
INSULATED REFRIGERANT LINES, SIZED ADHESIVE. ENDS OF DUCT WITH SEE FLOOR PLAN
PER MANUFACTURER'S SPECS 2" FROM EDGE FOR CONTINUATION
WALL AC ROOM OF LINER LINER SHALL BE BUTTED 90% MIN. AREA
FIRMLY TOGETHER COVERAGE OF BACKDRAFT
1'-621"x 5'-1021" FULL SIZE PIPE FLASHING AND FLASHING CAP, SEALED
THE VELOCITY RATED SIDE AND TAPED OVER. (MIRACLE PF96) DAMPER
LOUVER DOOR OF LINER MUST FACE THE (MIRACLE PF96) ADHESIVE
MEMBRANE TO OVERLAP FLASHING
AIR FLOW
ISSUE
COOLING COIL CONCRETE PAD
ON GRADE SURFACE REFRIGERANT PIPING IN WALL OR ABOVE CEILING
CEILING, ROUTED TO FAN COIL UNIT
(INSULATION NOT SHOWN)
CONDENSATE EXHAUST DUCT
DRAIN LINE
CONNECT TO
FLOOR DRAIN
SUPPORT STEEL

AHUs VERTICAL MOUNTING DETAIL CONDENSER UNIT SLAB @ GRADE DETAIL DUCT LINER DETAIL GUEST DRYER WALL BOX DETAIL WALL LOUVER DETAIL
4 3 2 1 9
REVISION

SCALE:

M3.0