Sealant Type Specification Requirements Proposed Material Remarks

GUARDIAN GP – Single-component, neutral cure, non-

Single-Component, Non-sag, Neutral-Curing sag silicone sealant. Complies with ASTM C920 Type S,
Direct match to specification. Suitable for general-purpose
Silicone Sealant Silicone Joint Sealant: In accordance with ASTM Grade NS, Class 25. UV resistant, flexible, and weather
construction joints.
C920, Type S, Grade NS, Class 25, for Use NT. durable. Used for glass, aluminum, and precast joints in
vertical and horizontal applications.

NEOFLEX PU 25 LM – One-component, low modulus

Single-Component, Nonsag, Urethane Joint polyurethane joint sealant. ASTM C920 compliant. Non-
Urethane Sealant Sealant: In accordance with ASTM C920, Type S, sag, paintable, excellent adhesion to porous substrates. Fully compliant. Ideal for façade and movement joints.
Grade NS, Class 25, for Use NT. Used for vertical and horizontal joints in precast, curtain
walls, and blockwork.
NEOSULPHIDE PG – Two-component pouring grade
Multicomponent, Nonsag, Traffic-Grade,
polysulfide joint sealant. Complies with ASTM C920 Type
Polysulfide Joint Sealant: In accordance with Exact match. Designed for high-performance infrastructure
Polysulfide Sealant M, Grade NS, Class 25. Fuel and chemical resistant. Used
ASTM C920, Type M, Grade NS, Class 25, for Use joints.
for horizontal expansion joints in water retaining and
T.
traffic areas.
ELEMENTS D3618 – One-part, siliconized acrylic acoustic
Latex Joint Sealant: In accordance with Acrylic
sealant. ASTM C834 compliant. Paintable, flexible, and Meets interior latex sealant requirements as per ASTM
Latex Joint Sealant latex or siliconized acrylic latex, ASTM C834,
easy to apply. Ideal for gypsum board joints, trims, and C834.
Type OP, Grade NF.
indoor acoustic sealant applications.
 C. Durability

1. Sealants and joint fillers to be serviceable and maintain their performance for the duration of
their service life without the following failures or defects.

a) Adhesive or cohesive failure.

b) Spalling of joint edges.

c) Slumping or folding of surface.

d) Extrusion beyond surfaces adjacent to joint.

e) Inclusions.

f) Crazing of surface greater than 0.1mm in depth.

g) Staining of adjacent surfaces.

h) Blistering of the surface.

i) Puncture of surface.

j) Chalking or color change.

k) Change in 'Shore A' durometer hardness of more than 15% of 7-day value.

l) Displacement.

m) Chemical attack.

2.4 MATERIALS
A. Silicone Joint Sealants

1. Single-Component, Non-sag, Neutral-Curing Silicone Joint Sealant: In accordance with ASTM C

920, Type S, Grade NS, Class 100/ 50, for Use NT.

2. Single-Component, Non-sag, Neutral-Curing Silicone Joint Sealant: In accordance with ASTM C

920, Type S, Grade NS, Class 50, for Use NT.

3. Single-Component, Non-sag, Neutral-Curing Silicone Joint Sealant: In accordance with ASTM C

920, Type S, Grade NS, Class 25, for Use NT.

Section 07 92 00 Joint Sealants

Page 7
 4. Single-Component, Non-sag, Acid-Curing Silicone Joint Sealant: In accordance with ASTM C
920, Type S, Grade NS, Class 25, for Use NT.

5. Single-Component, Nonsag, Traffic-Grade, Neutral-Curing Silicone Joint Sealant: In

accordance with ASTM C 920, Type S, Grade NS, Class 100/ 50, for Use T.

6. Single-Component, Pourable, Traffic-Grade, Neutral-Curing Silicone Joint Sealant: In

accordance with ASTM C 920, Type S, Grade P, Class 100/ 50, for Use T.

7. Multicomponent, Nonsag, Neutral-Curing Silicone Joint Sealant: In accordance with ASTM C

920, Type M, Grade NS, Class 50, for Use NT.

8. Multicomponent, Pourable, Traffic-Grade, Neutral-Curing Silicone Joint Sealant: In accordance

with ASTM C 920, Type M, Grade P, Class 100/ 50, for Use T.

9. Mildew-Resistant, Single-Component, Nonsag, Neutral-Curing Silicone Joint Sealant: In

accordance with ASTM C 920, Type S, Grade NS, Class 25, for Use NT.

10. Mildew-Resistant, Single-Component, Acid-Curing Silicone Joint Sealant: In accordance with

ASTM C 920, Type S, Grade NS, Class 25, for Use NT.

B. Urethane Joint Sealants

1. Single-Component, Nonsag, Urethane Joint Sealant: In accordance with ASTM C 920, Type S,
Grade NS, Class 100/ 50, for Use NT.

2. Single-Component, Nonsag, Urethane Joint Sealant: In accordance with ASTM C 920, Type S,
Grade NS, Class 50, for Use NT.

3. Single-Component, Nonsag, Urethane Joint Sealant: In accordance with ASTM C 920, Type S,
Grade NS, Class 25, for Use NT.

4. Single-Component, Nonsag, Traffic-Grade, Urethane Joint Sealant: In accordance with ASTM

C 920. Type S, Grade NS, Class 25, for Use T.

5. Single-Component, Pourable, Traffic-Grade, Urethane Joint Sealant: In accordance with ASTM

C 920, Type S, Grade P, Class 25, for Use T.

6. Multicomponent, Nonsag, Urethane Joint Sealant: In accordance with ASTM C 920, Type M,
Grade NS, Class 50, for Use NT.

7. Multicomponent, Nonsag, Urethane Joint Sealant: In accordance with ASTM C 920, Type M,
Grade NS, Class 25, for Use NT.

8. Multicomponent, Nonsag, Traffic-Grade, Urethane Joint Sealant: In accordance with ASTM C

920, Type M, Grade NS, Class 50, for Use T.

9. Multicomponent, Nonsag, Traffic-Grade, Urethane Joint Sealant: In accordance with ASTM C

Section 07 92 00 Joint Sealants

Page 8
 920, Type M, Grade NS, Class 25, for Use T.

10. Immersible, Single-Component, Nonsag, Traffic-Grade, Urethane Joint Sealant: In accordance

with ASTM C 920, Type S, Grade NS, Class 25, for Uses T and I.

11. Immersible, Single-Component, Pourable, Traffic-Grade, Urethane Joint Sealant: In

accordance with ASTM C 920, Type S, Grade P, Class 25, for Uses T and I.

12. Immersible Multicomponent, Nonsag, Traffic-Grade, Urethane Joint Sealant: In accordance

with ASTM C 920, Type M, Grade NS, Class 25, for Uses T and I.

13. Immersible Multicomponent, Pourable, Traffic-Grade, Urethane Joint Sealant: In accordance

with ASTM C 920. Type M, Grade P, Class 25, for Use T and I.

C. Polysulfide Joint Sealants

1. Single-Component, Nonsag, Polysulfide Joint Sealant: In accordance with ASTM C 920, Type S,
Grade NS, Class 25, for Use NT.

2. Multicomponent, Nonsag, Polysulfide Joint Sealant: In accordance with ASTM C 920, Type M,
Grade NS, Class 25, for Use NT.

3. Multicomponent, Nonsag, Traffic-Grade, Polysulfide Joint Sealant: In accordance with ASTM C

920, Type M, Grade NS, Class 25, for Use T.

4. Multicomponent, Pourable, Traffic-Grade, Polysulfide Joint Sealant: In accordance with ASTM

C 920, Type M, Grade P, Class 25, for Use T.

5. Immersible, Multicomponent Nonsag, Traffic-Grade, Polysulfide Joint Sealant: In accordance

with ASTM C 920, Type M, Grade NS, Class 25, for Use T and Use I.

D. Latex Joint Sealants

1. Latex Joint Sealant: In accordance with Acrylic latex or siliconized acrylic latex, ASTM C 834,
Type OP, Grade NF.

E. Solvent-Release-Curing Joint Sealants

1. Acrylic-Based Joint Sealant: In accordance with ASTM C 1311.

2. Butyl-Rubber-Based Joint Sealant: In accordance with ASTM C 1311.

Section 07 92 00 Joint Sealants

Page 9
 SEALANTS | CONSTRUCTION CHEMICALS | SPORTS FLOORING

PRODUCT DATA SHEET

GUARDIAN GP
SINGLE COMPONENT ACETIC CURE SILICONE SEALANT

DESCRIPTION AREA OF APPLICATION

GUARDIAN GP is a premium-quality, one-component, ace�c GUARDIAN GP is suitable for a wide range of sealing and
cure silicone sealant that vulcanizes upon exposure to bonding applica�ons, including:
moisture at room temperature. It forms a flexible, durable
elastomeric seal with excellent adhesion to a wide variety of Non-structural glazing
non-porous substrates such as glass, ceramic �les, aluminum, Structural a�achments of mul�-panel systems
and metals. Designed to resist ozone, UV radia�on, and Demanding sanitary applica�ons
extreme temperatures, GUARDIAN GP is ideal for a broad Panel s�ffener bonding
range of glazing and construc�on applica�ons. Aluminum, steel, and EIFS substrates
Painted metals, granites, and other natural stones
Concrete, brick, and various plas�cs
Kitchens and bath installa�ons (countertops, tubs, sinks,
ADVANTAGES / CHARACTERISTICS showers)
GUARDIAN GP offers excep�onal performance with mul�ple General sealing and adhesive applica�ons
benefits for long-term applica�ons: Cabinet assembly, carpentry, and installa�on works

Excellent adhesion to a wide range of non-porous surfaces

ensuring versa�le applica�on
Permanently flexible with low shrinkage for durable seals
Mould and mildew resistant, ideal for humid and wet areas
Outstanding resistance to weathering, moisture, ozone, and
UV exposure for exterior use
High elonga�on at break allowing for joint movement and
flexibility
All-temperature gun ability: easily applied between 5°C and
40°C for all-season use
Excellent tooling proper�es, enabling a clean, professional
finish
Suitable for both indoor and outdoor applica�ons in
demanding environments

PACKAGING AND COLOR

GUARDIAN GP is available in 280 ml cartridges, packed in
cartons of 24 cartridges.

Available Colors: Clear, White , Black & Grey ( RAL color ,

Special Color Order may Require lead �me and minimum
order quan��es)

Page 1

DS-RI-JS-GGP-V02-2025-01
TECHNICAL SPECIFICATION
PROPERTY VALUE TEST STANDARD
Chemical Base Single Component -

Cure type Acetoxy -

Appearance Smooth Paste -

Applica�on Temperature Range 5°C to 40°C -

Service Temperature Range -40°C to 110°C -

Specific Gravity 0.97 ± 0.2 g/cm³ ASTM D1475

Skin Over �me @ 25 0 C 4 to 7 min Approx. ASTM C679

Tack-Free Time 10 to 14 minutes ASTM C679

Depth Cure 24 hours 2 - 4 mm/day LAB Test

Durometer Hardness (Shore A) 27 ± 2 ASTM D2240

Tensile Strength > 1.30 N/mm² ASTM D412

Elonga�on at Break 600% ASTM D412

Modulus at 100% Elonga�on ~0.35 N/mm² ASTM D412

COVERAGE RATE
One 280 ml cartridge seals approximately 10 linear meters of
a 5mm x 5mm joint

METHOD OF APPLICATION
D. Avoid Applica�on In
A. Surface Prepara�on Wet or damp surfaces
All surfaces must be clean, dry, and free of dust, oil, Areas exposed to con�nuous water immersion
grease, and contaminants. Remove old sealants, dirt, Surfaces contaminated with oils, solvents, or release
and other debris by mechanical means. Use appropriate agents
primers where necessary for improved adhesion. Extremely high humidity or during rainy condi�ons

B. Applica�on E. Curing Time Considera�ons

Cut the �p of the cartridge at an angle and fix it into a Tack-free within 10 to 14 minutes under standard
standard caulking gun. condi�ons (25°C, 50% RH)
Apply the sealant uniformly into the joint ensuring full Thicker sec�ons or low humidity condi�ons may increase
contact with bonding surfaces. cure �mes
Tool the sealant immediately a�er applica�on to ensure
firm contact and a smooth finish.
Remove excess sealant before it skins over.
Ensure joints are designed to accommodate expected
movement.

C. Post-Applica�on Considera�ons
Allow sealant to skin over before exposing to dust or
water.
Avoid disturbing the sealant during ini�al curing.
Protect sealant from mechanical impact during curing

Page 2

DS-RI-JS-GGP-V02-2025-01
ENVIRONMENTAL CONDITIONS STORAGE & SHELF LIFE
Applica�on Temperature: 5°C to 40°C Op�mal Rela�ve Store in a cool, dry place between +5°C and +30°C. Keep
Humidity: 50% - 70% away from direct sunlight and sources of heat.
Substrate must be dry, clean, and stable
Ensure proper ven�la�on during applica�on and curing Shelf Life: 12 months from the date of manufacture if
stored in original unopened packaging under recom-
mended condi�ons.
HEALTH & SAFETY
Releases ace�c acid during curing; ensure adequate WARRANTY
ven�la�on.
Royal Industries LLC warrants that GUARDIAN GP will meet
Avoid direct contact with uncured sealant; may cause eye
its specifica�ons at the �me of delivery. Liability is limited
or skin irrita�on.
to the replacement of defec�ve product or refund of the
Wear appropriate PPE: gloves, goggles, and protec�ve
purchase price. Please refer to Royal Industries’ Terms
clothing.
& Condi�ons of Sale for full details.
In case of contact, rinse thoroughly with water and seek
medical advice if necessary.

For further details, refer to the Safety Data Sheet (SDS).

CERTIFICATES & STANDARDS

DCL Cer�fied
Conforms to ASTM C920, Type S, Grade NS, Class 25, Use
NT, G, A.
Manufactured under ISO-cer�fied quality management
systems.

The technical information and application advice given in this ROYAL INDUSTRIES LLC publication are based on
STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law.
The user is responsible for checking the suitability of products for their intended use.

NOTE ROYAL INDUSTRIES LLC either orally or in writing may be followed, modified or rejected by the owner, engineer or
contractor since they, and not ROYAL INDUSTRIES LLC, are responsible for carrying out procedures appropriate to
a specific application.

Manufactured by :
Royal Industries L.L.C
Email: info@royalindustries.ae
Tel: +971 6 5679000 SEALANTS | CONSTRUCTION CHEMICALS | SPORTS FLOORING

P.O.Box 650 34 Page 3

DS-RI-JS-GGP-V02-2025-01
 NEOFLEX PU 25 LM
Polyurethane Sealant
NEOFLEX PU 25-LM is a one-component, low-modulus polyurethane sealant that cures on exposure to atmospheric humidity.
Meets the requirements of ISO 11600 F 25 LM, ASTM C-920, ASTM C 719 - Type S, Grade NS Class 25 Use NT, M.A

PROPERTIES

Possesses permanent elasticity

No sagging – Thixotropic
No shrinkage
PROPRETIES
Can be applied using a manual application gun and
easily Paintable (recommended to apply elastomeric
flexible paint only).
25 % movement capability
Confirms to BS 6920
Suitable for use in Potable water Tanks under special
conditions.
CHARACTERISTICS
Acoustic Sealant

AREAS OF APPLICATION

Expansion joints between many different construction PACKAGING

materials
Movement and construction joints in floors NEOFLEX PU 25 LM is available in 600 ml Sausage.
Indoor and outdoor applications for pedestrian and
traffic areas
Joints between prefabricated construction materials
CONSUMPTION (approx.)
Sealing and bonding of ventilation ducts, gutters and
spouts etc. Joint Width 15mm 20mm 25mm 30mm 35mm
Excellent Material for sealing joints between pre-cast
concrete panels Joint Depth 8mm 10mm 12mm 15mm 15mm
Conceal GRC & GRP Lining joints
Joint 5m 3m 2m 1.3m 1.1m
Length/600ml
METHOD OF APPLICATION

NEOFLEX PU 25 LM sealant shall be applied as per the

following general method of application:
PACKAGING
Before application, the joint surfaces should be thoroughly
clean, dry and free of all contamination. Apply sealant PRODUCT VOLUME PACKAGING
evenly, use masking tape and remove the tape while the
WHITE (Sausage) 600 ml 20
sealant is still tacky.
Joint width/depth ratio should be 2:1 BEIGE (Sausage) 600 ml 20
Use a high density polyethylene backer rod as a backup
material always to adjust the joint width – depth ratio. GREY (Sausage) 600 ml 20
Sealants should adhere to only two surfaces of the joint to
take care of thermal expansion and contraction of the joint.

RESTRICTIONS

Avoid application below +5°C and above +45°C

Do not apply on frozen or wet surface or through
standing water at all.

Page 1

Revision Date 09.05.2024 Revision No. 01 TDS-S-NPU-001_05/24

 HEALTH & SAFETY TECHNICAL SPECIFICATION

Protective clothing such as gloves and goggles should be

worn while applying NEOFLEX PU 25 LM. In case the PROPERTIES TYPICAL VALUES TEST
material splashes to the skin or eyes wash the same with STANDARDS
fresh water immediately. BEFORE CURING
Color White – Grey – Note: special
In critical cases seek medical assistance. Beige color can be
made upon
request as per
STORAGE & SHELF LIFE MOQ norms.
Base Polyurethane -
NEOFLEX PU 25 LM should always be stored in dry and
consistency Thixotropic
covered areas. The product should not be exposed to direct
sunlight or be kept near any source of heat. Store in indoor Curing Mechanism Moisture Curing -
at 25 °C Density, g/ml 1.50 ± 0.05
Tack free Time 30 – 60 min (23°C
The product Shelf life is up to 12 months when stored as per and 50% R.H)
the recommended storage conditions. Curing rate Min. 2.5mm/day -
(23°C and 50% R.H)
Sagging 0mm EN ISO 7390
Temperature -40°C to +90°C -
Resistance
Application +5°C to +45°C -
Temperature
AFTER CURING
Hardness Shore A 40 ± 3 After 28 days
(ASTM C661)
Paintibility Yes* -
Elastic Recovery ISO 7389
*Considering the diversity of paint base and quality,
compatibility tests should be done before application.
GLASS-GLASS
Elongation at Min 200% ISO 8339
Break
E100 Modulus 0.35-0.40 N/mm² ISO 8339
(23°C)
E100 Modulus (- ISO 8339
20°C)
DUMBLE TEST
Elongation at ASTM D412
Break
Tensile Strength 1.5 – 2.0 N/mm² ASTM D412

All values are subject to 5-10 % tolerance

NOTE: The information contained in this DATA SHEET, as well as our advice, both written as oral or ROYAL INDUSTRIES LLC
provided through testing, are based on our experience, and they do not constitute any product
Sajaa Industrial Area behind Sharjah Cement
guarantee for the installer, who must take them as simple orientations, provided strictly as information.
We recommend to study deeply all information provided before proceeding to the use or application Factory, Sharjah U.A.E.
of any of our products, and strongly advise to conduct tests “on-site” in order to determine their Email: qcdept@royalindustries.ae
convenience for a specific project. Our recommendations do not exempt of the obligation that PO BOX: 65034
installers have to deeply know the right application method for these systems before they use them, Tel: +971 6 5679000
as well as to conduct as many preliminary tests as possible if there are any doubts about the
Website: www.royalindustries.ae
appropriate system to use. The application, use and processing of our products are beyond our control,
and therefore under the exclusive responsibility of the installer. In consequence, the installer will be
the only responsible of any damage or prejudice derived from the partial or total in-observation of
our indications, and in general, of the inappropriate use or application of these materials.

Page 2

Revision Date 09.05.2024 Revision No. 01 TDS-S-NPU-001_05/24

 SEALANTS | CONSTRUCTION CHEMICALS | SPORTS FLOORING

PRODUCT DATA SHEET

NEOSULPHIDE PG
TWO-COMPONENT, POURING GRADE POLYSULPHIDE SEALANT

DESCRIPTION AREA OF APPLICATION

NEOSULPHIDE PG is a high-performance, two component, NEOSULPHIDE PG is designed for sealing horizontal movement
pouring-grade polysulphide-based joint sealant. Upon mixing joints in various construc�on and infrastructure projects, including:
and applica�on, it cures to form a tough, highly elas�c, and
durable rubber-like seal. The sealant exhibits excellent Expansion joints in concrete floors and pavements
weathering, chemical, and mechanical resistance, making it PQC (Pavement Quality Concrete) joints and precast
ideal for horizontal joints subject to movement and exposure concrete elements
to aggressive environmental condi�ons. Bridge deck joints and culvert joints
Reservoirs, canals, and water retaining structures
Horizontal joints in vacuum dewatered floors
Crack repairs in concrete surfaces
ADVANTAGES / CHARACTERISTICS Trafficable joints in airport runways, car parks, roads, and
industrial floors
NEOSULPHIDE PG offers the following key benefits:
Situa�ons requiring permanently flexible horizontal sealing
Easy to use two-component system
Economical and cost-effec�ve joint sealing solu�on Its excep�onal durability makes it the preferred choice for
Excellent adhesion to concrete, metals, and various substrates cri�cal civil and infrastructure projects.
Good chemical and fuel resistance
Permanently elas�c with excellent movement accommoda�on
Outstanding weather and aging resistance
High resistance to physical damages and climate extremes

PACKAGING AND COLOR

NEOSULPHIDE PG is supplied in 4-liter kits (Part A and Part B
combined).

Available Colors: Grey.

Page 1

TDS-RI-JS-NGP02-V02-2025-01
TECHNICAL SPECIFICATION
PROPERTY TYPICAL VALUES TEST STANDARD
Type Two-Component Polysulphide Sealant -

Color Grey -

Density 1.6 ± 0.02 kg/L ASTM D1475

Applica�on Temperature Range >+5°C to +50°C -

Service Temperature Range -20°C to +120°C -

Movement Accommoda�on ±25% ISO 11600

Elonga�on at Break 500% ASTM D412

Shore A Hardness 15 ±5 ASTM D2240

Solid Content 100% -

Tack Free Time 36 hours -

Curing Time Approximately 1 week -

Pot Life >60 Minutes -

Recovery A�er Extension High -

Water Immersion Resistance Fully cured sealant only -

Pain�ng Yes, subject to compa�bility tes�ng -

METHOD OF APPLICATION
SURFACE PREPARATION APPLICATION PROCEDURE
Ensure joint surfaces are dry, clean, sound, and free from dust, Pour the mixed material directly into the prepared horizontal joints.
laitance, oil, grease, or any contaminants that may impair adhesion. Use a sealant gun if necessary for controlled applica�on.
Mechanical cleaning methods such as wire brushing or grit Tool the surface to achieve a smooth finish.
blas�ng are recommended. Use a dilute detergent solu�on if needed.
Metal surfaces should be free of rust, scale, and protec�ve Remove any masking tape immediately a�er tooling.
lacquers.
COVERAGE
PRIMING Theore�cal coverage based on joint
For porous substrates such as concrete, brick, or stone,
Joint Size (mm) Liters per Meter Run Meter Run per 4L Kit
apply a thin coat of NEOPRIME PS2 primer.
Allow the primer to become tack-free before applying 10 x 10 0.100 40.0
the sealant but ensure the sealant is applied within the 20 x 20 0.200 20.0
primer's open �me. 20 x 20 0.400 10.0
40 x 40 0.800 5.0
MIXING Allowances must be made for wastage and joint irregulari�es.
NEOSULPHIDE PG is supplied in two separate containers
(Part A and Part B). Post-Applica�on Considera�ons
Transfer the en�re contents of Part B into Part A. Protect freshly applied sealant from rain, dust, and
Mix thoroughly for 5 minutes using a low-speed mechanical extreme temperatures during the ini�al cure.
mixer un�l a uniform, homogeneous consistency is achieved. Light traffic is permissible a�er 48 hours; full chemical
Mixing Ra�o: Part A : Part B = 95 : 5 (by weight). resistance and durability are achieved a�er 7 days

Page 2

TDS-RI-JS-NGP02-V02-2025-01
AVOID APPLICATION IN STORAGE & SHELF LIFE
Joints with standing water or high moisture Store in a cool, dry area between +5°C and +30°C.
Direct contact with bituminous surfaces or highly Protect from direct sunlight and heat.
chlorinated water
Cold weather below +5°C unless specially approved Shelf Life: 12 months in original, unopened packaging
under recommended storage condi�ons.
CURING TIME CONSIDERATIONS
Ini�al cure: 48 hours at 25°C HEALTH & SAFETY
Full cure: 7 days depending on ambient condi�ons Wear protec�ve gloves, safety glasses, and clothing
during handling and applica�on.
ENVIRONMENTAL CONDITIONS Avoid contact with skin and eyes. In case of contact, rinse
Applica�on Temperature Range: +5°C to +50°C immediately with clean water.
Rela�ve Humidity: 50%-70% op�mal Ensure adequate ven�la�on during applica�on.
Substrate must be dry and clean Refer to the Safety Data Sheet (SDS) for detailed health
and safety informa�on.
CERTIFICATES & STANDARDS
DCL Cer�fied
Manufactured under ISO-cer�fied quality management
systems
Tested in accordance with ISO 11600, BS 4254, ASTM
C920, Federal Specs TT-S-00227E

The technical information and application advice given in this ROYAL INDUSTRIES LLC publication are based on
STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature, no
RESPONSIBILITY assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law.
The user is responsible for checking the suitability of products for their intended use.

NOTE ROYAL INDUSTRIES LLC either orally or in writing may be followed, modified or rejected by the owner, engineer or
contractor since they, and not ROYAL INDUSTRIES LLC, are responsible for carrying out procedures appropriate to
a specific application.

Manufactured by :
Royal Industries L.L.C
Email: info@royalindustries.ae
Tel: +971 6 5679000 SEALANTS | CONSTRUCTION CHEMICALS | SPORTS FLOORING

P.O.Box 650 34 Page 3

TDS-RI-JS-NGP02-V02-2025-01
 ELEMENTS D 3618
Acrylic Acoustic Sealant - Siliconized Duct Seal 36-18

ELEMENTS D3618 Acrylic Acoustic Sealant is a water based general-purpose, paintable sealant that is used for caulking, grouting,
jointing, acoustic assemblies and embedding in building construction. It is easy to apply and compatible with most materials used
in construction e.g. concrete, wood, brick, natural and artificial stone, metal, and sanitary ware. Optimus Acrylic is flexible and resists
cracking, giving a smooth finish that is suitable for interior and exterior use.

PROPERTIES
Over paintable in one hour
Flexible with low VOC
Excellent airborne sound insulation properties.
PROPRETIES
Provides a smooth finish
Water based and non-toxic
Complies the standard BS3712

FIELD OF APPLICATION

ELEMENTS D3618CHARACTERISTICS
Acrylic Sealant is ideal for sealing low
movement joints, as a flexible crack filler before painting
jobs, for sealing construction frameworks e.g. between
window and door frames and walls: Suitable for Duct Seal
Joints, acoustic assemblies also suitable as an adhesive for
bonding. If there is any uncertainty regarding the
application, adhesion tests should be carried out.

LIMITATION

Not to be used where high movement accommodations

SURFACE PREPARATION
is needed.
Surfaces to be bonded must be clean, structurally sound,
Not to be used on oily, bituminous substrates, rubber dry, and free from dust, dirt, oil, rust, and loose material.
or materials that may bleed oils, plasticizers, or Non-porous substrates such as metals should be degreased
solvents. with a solvent. Poor surface preparation may result in the
Not recommended for use in floor joints, as a glass delamination of the sealant. Gaps exceeding 5mm should be
sealant, or joints subject to continuous water immersion. filled with backing material before application. Remove
When using mastic acrylic do not expose to water or rain excess acrylic sealant and clean tools immediately after
for at least 24 hours. application, using soapy water. Cured acrylic sealant can be
Will not adhere to some plastics such as polyethylene, removed mechanically i.e. with a sharp knife.
polypropylene, and Teflon.
Not sandable.
PACKAGING

ELEMENTS D3618 is available in 280ml cartridge.

METHOD OF APPLICATION
Customized Bulk packing upon request.
SAFETY INSTRUCTIONS
ELEMENTS D3618 Acrylic Sealant is non-toxic. Avoid contact
with eyes. In the event of skin or eye contact, rinse
thoroughly and immediately with water. Seek medical
assistance if irritation or discomfort persists. Keep out of
reach of small children! Refer to our Safety Data Sheet for
further toxicological information and comprehensive
handling instructions.

Page 1

Revision Date 15.05.2024 Revision No. 01 TDS-S-ED-001_05/24

 HEALTH & SAFETY TECHNICAL SPECIFICATION

Protective clothing such as gloves and goggles should be

worn while applying ELEMENTS D3618 In case the material PRODUCT CHARACTERISTICS
splashes to the skin or eyes wash the same with fresh water
immediately. Type Acrylic

In critical cases seek medical assistance. Appearance White homogenous non

sag paste

Skin formation / Tack Free time Approximately 10-12

STORAGE & SHELF LIFE minutes Max

pH 7.0 – 8.0
ELEMEN TS D3618 cartridge should always be stored in
dry and covered areas. The product should not be Odour Mild
exposed to direct sunlight or be kept near any source of Solids (%) Approximately 80-85
heat. Store in indoor a t 25 C.
Viscosity Thixotropic consistency
The product Shelf life is up to 24 months when stored as
Specific gravity (DIN 53479) 1,70±0,05 g/cm³
per the recommended storage conditions.
(ASTM D792)

ELEMENTS D3618 cartridge should always be stored in dry TYPICAL PERFORMANCE DATA
and covered areas. The product should not be exposed to
direct sunlight or be kept near any source of heat. Store in Application temperature Min. 5°C to Max. 50°C
indoor at 25 C.
Coverage Approximately 20m (4 x
The product Shelf life is up to 15-18 months when stored as 4 mm)
per the recommended storage conditions.
Service temperature range -10 to 80°C

Modulus at 100% elongation

[ASTM D412]

Sound transmission classification STC 53 - ASTM E90

Elongation at break [ASTM D412]

Curing time Approximately 48 hours

per 2mm (25°C, 50%
RH)

Shore A hardness [ASTM D412] 30 ±2

Disclaimer: The information given in this sheet is not intended to be exhaustive and any person using the product for any purpose ROYAL INDUSTRIES LLC
other than that specifically recommended in this document without first obtaining written confirmation from Royal Industries as to the
suitability of the product for the intended purpose does so at his/her own risk. The information contained herein has been prepared in
PO BOX: 65034 Sharjah U.A.E.
good faith to comply with applicable regional Law. However, no warranty of any kind is given or implied and Royal Industries will not be Tel: +971 6 572 6378
responsible for any damages, losses or injuries that may result from the use of any information contained herein. While Royal Industries
endeavors to ensure all advice it gives about the product (whether in this document or otherwise) is correct, we have no control over either Email: info@royalindustries.ae
the quality or condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless Royal Website: www.royalindustries.ae
Industries specifically agrees in writing to do so, it does not accept any liability whatsoever or howsoever arising for the performance of the
product, or for any consequential loss or damage arising out of the use of the product. Any warranty, if given or specific Terms & Conditions
of Sale are contained in Royal Industries, Terms & Conditions of Sale, a copy of which can be obtained upon request. The information
contained herein is liable to modification from time-to-time considering experience and Royal Industries policy of continuous product
improvement.

Page 2

Revision Date 15.05.2024 Revision No. 01 TDS-S-ED-001_05/24