Electric Drives Linear Motion and

and Controls Hydraulics Assembly Technologies Pneumatics Service

Axial piston-variable motor A10VM RA 91703/11.07

Replaces:11.04
/28

Plug-in version A10VE

Technical Data Sheet

Series 52
Size 28...85
Nom. pressure 4000 psi (280 bar)
Peak pressure 5100 psi (350 bar)
open and closed circuit

Contents Features
Ordering code - Standardprogram 2 – Dual displacement motor, axial piston swashplate design,for
hydrostatic transmissions in open and closed circuits
Technical data 4
– Output speed is directly proportional to inlet flow and inver-
Two-point direct control DG 7
sely proportional to motor displacement
Two-point control, hydraulically operated HZ/HZ6 8
– Output torque increases proportional to the pressure dif-
Two-point control, electrically operated EZ 9 ference between high and low pressure sides and increasing
displacement
Unit dimensions A10VM, Size 28 10
– Heavy duty bearings for long service life
Unit dimensions A10VM, Size 45 12
– High permissible output speed
Unit dimensions A10VM, Size 63 14
– Well proven A10-rotary unit technology
Unit dimensions A10VM, Size 85 16
– High power/weight ratio – compact dimensions
Unit dimensions A10VE, Size 28 18
– Cost effective
Unit dimensions A10VE, Size 45 20
– Low noise
Unit dimensions A10VE, Size 63 22
– Control range 1 : 3,75
Integrated flushing and boost press. relief valve, N007 24
– External control pressure supply possible
Speed pickup 25
– Minimum displacement can be set externally
Mounting position 26
– SAE-2-bolt mounting flange on A10VM
Notes 27
– Special 2-bolt mounting flange on A10VE
General Notes 28
/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Ordering code - Standardprogram

A10V M / 52 W – V C
01 02 03 04 05 06 07 08 09 10 11 12 13
Axial piston unit
01 Swash plate design, variable A10V

Operating mode
02 Motor M

size 28 45 63 85
03 ~ Displacement Vg max [in3 /rev.] (cm3 /rev.) 1.71 (28) 2.75 (45) 3.78 (62) 5.19 (85)

Control devices 28 45 63 85
Two point control
Directly operated, external control supply, without pilot valve DG
Hydraulically operated Stroking time without HZ
orifice with HZ6
04
Electrically with solenoid valve Stroking time without EZ1
Control voltage 12V orifice with EZ6
Electrically with solenoid valve Stroking time without EZ2
Control voltage 24V orifice with EZ7

Series
05 52

Direction of rotation
06 Viewed on shaftend Bi-directional W

Minimum displacement 28 45 63 85
Vg min in3 (cm3) steplessly adjustable from/to 0.49/1.71 0.73/1.52 0.98/2.32 1.34/3.05
1
(8/28) (12/25) (16/38) (22/50)
07
Adjustment please state in clear text from/to 1.59/2.75 2.44/3.78 2.93/5.19
­— 2
(26/45) (40/62) (48/85)

Seals
08 FKM (fluor rubber) V

Shaft end 28 45 63 85
Splined acc. to SAE J744 R
09
(for details see unit dimensions) – W

Mounting flange
10 SAE 2-bolt C

Ports for service lines

SAE flanges , at side-same side, UNC fixing screws 60N00
11 SAE flanges at rear, UNC fixing screws 61N00
Threaded ports on side-same side, UNC thread 66N00

Valves
Without valves 0
12
Integrated flushing valve, only with side ports (10N00 and 16N00) 7

Speed pickup
Without speed pickup —
13
Prepared for inductve type of speed pickup ID R D
available in preparation – not available
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation /28

Ordering code - Standardprogram

A10V E / 52 W – V F
01 02 03 04 05 06 07 08 09 10 11 12 13
Axial piston unit
01 Swash plate design, variable A10V

Operating mode
02 Motor, plug-in type E

Size 28 45 63
03 ~ Displacement Vg max [in3 /rev. (cm3 /rev.)] 1.71 (28) 2.75 (45) 3.78 (62)

Control devices 28 45 63
Two point control
Directly operated, external control supply, without pilot valve DG
Hydraulically without HZ
Stroking time orifice
with HZ6
04
Electrically with solenoid valve without EZ1
Stroking time orifice
Control voltage 12V with EZ6
Electrically with solenoid valve without EZ2
Stroking time orifice
Control voltage 24V with EZ7

Series
05 52

Direction of rotation
06 Viewed on shaftend Bi-directional W

Minimum displacement 28 45 63
Vg min in3 (cm3) steplessly adjustable from/to 0.61/1.71(10/28) 0.73/1.52(12/25) 0.98/2.32 (16/38) 1
07
Adjustment please state in clear text from/to ­— 1.59/2.75 (26/45) 2.44/3.78 (40/62) 2

Seals
08 FKM (fluoro rubber) V

Shaft end 28 45 63
Splined acc. to SAE J744 R
09
(for details see unit dimensions) – W

Mounting flange
10 Special 2-bolt F

Ports for service lines

SAE flanges at side-same side, UNC fixing screws 60N00
11 SAE flanges at rear, UNC fixing screws 61N00
Threaded ports on side-same side, UNF thread 66N00

Valves
Without valves 0
12
Integrated flushing valve, only with side ports (10N00 and 16N00) 7

Speed pickup
Without speed pickup —
13
Prepared for inductive type of speed pickup ID R D
available in preparation – not available
/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Technical data
Fluid se of extreme operating parameters or high ambient tempera-
tures please consult us
Prior to project design please see our data sheets RE 90220
(mineral oil), RE 90221 (ecologically acceptable fluids) and Filtration of fluid
RE90223 (HF-fluids) for detailed information on fluids and The finer the filtration the better the achieved cleanliness of the
application conditions. fluid and the longer the life of the axial piston unit.
When operating on ecologically acceptable fluids, limitations to To ensure a reliable functioning of the axial piston unit, a mini-
the techical data may be necessary. mum cleanliness of
Please contact us and state the fluid used in clear text when 20/18/15 to ISO 4406 is necessary.
ordering.
At very high fluid temperatures (194 °F to max. 240 °F)(90 °C
Operating viscosity range to max. 115 °C)) the minimum cleanliness has to be at least
For optimum efficiency and service life we recommend an ope- 19/17/14 to ISO 4406 .
rating viscosity (at operating temperature) in the range
If above cleanliness classes cannot be met please consult us.
nopt = opt. operating viscosity 80...170 SUS (16...36 mm2/s)
Operating pressure range
referred to circuit temperature in closed circuits or tank tempe-
Pressure at port A or B
rature in open circuits.
(Pressure data to DIN 24312)
Limits of viscosity range
Nominal pressure pN_________________ 4000 psi (280 bar)1)
The following limits are valid for extreme operating conditions:
Peak pressure pmax_ ___________________5100 psi (350 bar)
nmin = 42 SUS (5 mm2/s) (closed circuit) With motors connected in series please consult us.
nmin = 60 SUS (10 mm2/s) (open circuit)
Case drain pressure
briefly (t ≤ 1 min) at max. permissible temperature of 240 °F
Max. permissible pressure at leakage port L
(115 °C).
pabs max operation as motor in open circuit_ __58 psi(4 bar abs)
Please note, that the max. fluid temperature of 240 °F (115 °C)
pabs max operation as motor in closed circuit__58 psi(4 bar abs)
may also not be exceeded in certain areas (for instance bearing
pabs max motor/pump operation in open circuit 29 psi(2 bar abs)
area) The temperature in the bearing area is approx. 9°F (5 K)
higher than the average fluid temperature. Direction of rotation
nmax = 7400 SUS (1600 mm2/s) Direction of rotation, viewed on shaft end
briefly (t ≤ 1 min)
on cold start (tmin = -13 °F (-25°C), p ≤ 435 psi (30 bar), n ≤ clockwise counter-clockwise
1000 rpm). B to A A to B
At temperatures between -13 °F (–25 °C) and -40 °F (–40 Adjustment of displacement
°C) special measures may be required for certain installation
positions. Please consult us for further information The minimum displacement is steplessly adjustable within the
range of the screw lenghts 1 or 2 (see ordering code).
For detailed information on operation at very low temperatures
see RE 90300-03-B. Please state minimum displacement in clear text when orde-
ring.
Notes on the selection of the hydraulic fluid Selection diagram
In order to select the correct fluid, it is necessary to know the -40° -4° 32° 68° 104° 140° 176° 212° °F
operating temperature in the tank (open circuit), circuit tempe- -40° -20° 0° 20° 40° 60° 80° 100° °C
7400 1600 1600 7400
rature (closed circuits), in relation to the ambient temperature. 4600 1000
3000 600
2000 400
The fluid should be selected, so that within the operating tem-
VG 68

1000
VG
VG 22
VG 32
VG 46

200
peratue range, the viscosity lies within the optimum range (nopt)
10

500 100
0

, see shaded section of the selection diagram. We recommend

300 60
to select the higher viscosity grade in each case.
Viscosity n

200 40 36 170
Example: at an ambient temperature of X °F (X °C) the opera-
100 20
ting temperature in the tank is 140 °F (60 °C). In the optimum 80 16 80
viscosity range (nopt; shaded area) this corresponds to viscosi- 60 10
ty grades VG 46 resp. VG 68; select VG 68.
SUS mm 2/s mm 2/s SUS
Important: The leakage oil (case drain oil) temperature is influ- 42 5 5 42
-40° -25° 10° 0° 10° 30° 50° 70° 90° 115° °C
enced by pressure and motor speed and is always higher than
the tank temperature. However, at no point in the circuit may -40° -13° 14° 32° 50° 86° 122° 158° 194° 240° °F

the temperature exceed 240 °F (115 °C). Temperature t

tmin = -40°F (-40°C) Fluid temperature range tmax = 240°F (115°C)
If it is not possible to comply with the above conditions becau-
1) Higher pressures on request
 RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation /28

Technical data
Table of values
theoretical, rounded values, without considering hmh and hv

Size 28 45 63 85
Displacement Vg max in3 (cm3) 1.71 (28) 2.75 (45) 3.78 (62) 5.31 (87)
V g min in3 (cm3) 0.49 (8 (VM) 0.73 (12) 0.98 (16) 1.34 (22)
0.61 (10)(VE)
Speed1)
max. at Vg max n0 max rpm 4700 4000 3300 3100
max. at Vg min n0 cont. rpm 5400 4600 3900 3560
Min. speed in cont. operation n0 min rpm 250 250 250 250
Inlet flow
at n0 max and Vg max qV0 max gpm (L/min) 34.8 (131,6) 47.5 (180) 54 (205) 71.3 (270)
Torque constant2) at Vg max TC lb-ft/psi (Nm/bar) 0.022 (0,445) 0.036 (0,716) 0.049 (1,002) 0.071 (1,35)
Torque
at Vg max pN= 4000 psi Tmax lb-ft 91 146 200 283
(280 bar) (Nm) (125) (200) (276) (387)
Actual starting torque
at n = 0 rpm pN = 4000 psi T lb-ft 67 108 149 184
(280 bar) Nm (92) (149) (205) (253)
Rotary stiffness Shaft R c lb-ft/rad 18900 29800 50500 111600
(Nm/rad) (26000) (41000) (69400) (152900)
Shaft W c lb-ft/rad 14400 25000 39300 85800
(Nm/rad) (19800) (34400) (54000) (117900)
Mass moment of inertia JTW lb-ft2 0.0403 0.0783 0.1329 0.2847
(about output shaft)
(kgm2) (0,0017) (0,0033) (0,0056) (0,012)
Angular acceleration, max. a rad/s2 5500 4000 3300 2700
Filling volume V gal (L) 0.16 (0,6) 0.185 (0,7) 0.21 (0,8) 0,26 (1,0)
Weight approx. m lbs (kg) 30.9 (14) 39.7 (18) 57.3 (26) 75.0 (34)
1) At max. speed in closed circuit operation make sure that motor outlet pressure is at least ≥ 18 bar.
2) in open circuit ∆p 280bar at pboostpress. 2bar
in closed circuit ∆p 260bar at pboostpress. 20bar

Minimum required outlet pressure at port A (B)

depending on motor speed

363 25

290 20
Outlet pressure pND [bar]

permissible
range
218 15

145 10

73 5

0 0
psi bar 0,8 0,9 1 1,1 1,2
Motor speed n/nmax
/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Technical data
Calculating size
Vg • n Vg = geometric displacement per rev. in3
Flow qV = [gpm]
231 • hV ∆p = Differential pressure in psi
Vg • ∆p • hmh n = speed in rpm
Torque T = [lb-ft]
24 • p hV = volumetric efficiency
hmh = mechanical-hydraulic efficiency
T•n qV • ∆p • ht ht = Total efficiency (ht = hV • hmh)
Output power P = = [HP]
5252 1714 TK = Torque constant
qv • 231 • hv
Output speed n = [rpm]
Vg

Vg • n Vg = geometric displacement per rev. in cm3

Flow qV = [L/min]
1000 • hV ∆p = Differential pressure in bar
1,59 • Vg • ∆p •hmh n = speed in rpm
Torque T = [Nm]
100 hV = volumetric efficiency
or T = TK • ∆p • hmh hmh = mechanical-hydraulic efficiency
2p • T • n qV • ∆p • ht ht = Total efficiency (ht = hV • hmh)
Output power P = = [kW]
60000 600 TK = Torque constant
qv • 1000 • hv
Output speed n = [min-1]
Vg

Permissible radial and axial forces on drive shaft

Size 28 45 63 85

Max. radial Fq
bei X/2 Fq max lb 270 337 382 450
force X/2 X/2 (N) (1200) (1500) (1700) (2000)
X

Max. axial force Fax lb 225 337 450 674

± Fax
(N) (1000) (1500) (2000) (3000)
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation /28

Two-point direct control DG

Normally the motor is at max. displacement. By applying an ex- Schematic
ternal pressure to port G, the control piston is directly pressuri-
zed.and the motor swivels back to min. displacement
L L1 G G1
The minimum required control pressure is pSt ≥ 580 psi
(40 bar) A
Please note, that this minimum required control pressure at
port G depends directly on the operating pressure pB in port A
or B. (Pressure in A or B),see control pressure diagram below.
With a control pressure above this minimum required pressure
level the motor will destroke properly.

B
Control pressure diagram

2030 140

1450 100
Control pressure pSt

870 60
580 40
290 20 Ports
psi bar
0 20 40 60 100 140 180 220 260280 bar A, B Pressure port
290 870 1450 2030 2610 3190 3770 psi L, L1 Case drain ports
580 4000
Operating pressure pB G, G1 Ports for external control pressure

Control pressure = 0 psi (0 bar) ^

= Vg max
Control pressure ≥ 580 psi (40 bar) = Vg min (see diagram)
The max. perm. control pressure is pSt ^
= 4000 psi (280 bar).
Vgmin.. adjustment please state in clear text with order
/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Two-point control, hydraulically operated HZ/HZ6

Normally the motor is at max. displacement. By applying a Schematic HZ
pilot pressure pX to port X the pilot valve shifts and the control
piston is pressurized causing the motor to swivel to min. X
displacement.(pX ≥ 435 psi (30bar)).
The necessary control pressure is via a shuttle valve taken
out of the motor pressure side A or B. A minimum pressure
difference of DpA,B ≥ 290 psi (20 bar) between the motor
pressure sides is required.
L L1 A
Only Vg max or Vg min are possible.
Vg min - adjustment please state in clear ext when ordering.

4000 psi
(280 bar)

B
Pilot pressure px

435 psi
(30 bar) Ports
145 psi A,B Pressure ports
(10 bar)
L, L1 Case drain ports
X Pilot pressure port

Schematic HZ6
X
Vg min Displacement Vg max

Pilot pressure pX = 0 psi (0 bar) ^

= Vg max
Pilot pressure pX ≥ 435 psi (30 bar) ^
= Vg min

Techn. data HZ/HZ6

Minimum pilot pressure 435 psi (30 bar)
Maximum pilot pressure 4000 psi (280 bar)
L L1 A
Version HZ6 with stroking time shuttle orifice
Slow down of swivel action by means of shuttle orifice.
This enables a smooth swivel action.
Standard orifice size = dia 0.0083 in (ø 0,21 mm); other sizes
on request.

Ports
B
A,B Pressure ports
L, L1 Case drain ports
X Pilot pressure port
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation /28

Two-point control, electrically operated EZ

Normally the motor is at maximum displacement. By energizing Schematic EZ1/2
the solenoid of the control valve, the control piston is pressuri-
zed and the motor swivels to minimum displacement.
The control pressure is via a shuttle valve taken out of the
motor pressure side A or B. A minimum pressure difference
of DpA,B ≥ 290 psi (20 bar) between the pressure sides is
required. L L1 A
The motor can only swivel between Vg max or Vg min.
Vg min-adjustment please state in clear ext when ordering.

12V / 24V

B
Ports
A,B Pressure ports
L, L1 Case drain ports

Connection to solenoid Plug connection to

0
acc. to DIN 43650 DIN EN 175301-803-A
V g min V g max Cable screw joint
M16x1.5

De-energized ^V
= g max

Energized ^
= Vg min

PE PE
A A
Techn. data EZ 1 2 1 2
Version EZ 1/6 EZ 2/7
Supply voltage 12V DC 24V DC
Nom. current at 68 °F (20°C) 1,5 A 0,8 A
Schematic EZ6/7
Duty cycler 100% 100%
Plug protection class IP 65 IP 65
to DIN 43650

Ambient temperature range -4°F (-20°C) to 140°F(+60°C).

If the above temperature range cannot be met please consult
us.

L L1 A
Features
– with spring return at solenoid
– Solenoid plug can be turned 4 x 90°

Version EZ6/7 with stroking time shuttle orifice

Slow down of swivel action by means of shuttle orifice.
This enables a smooth swivel action.
B
Standard orifice size = 0.0083 in (0,21mm); other sizes on Ports
request. A,B Pressure ports
L, L1 Case drain ports
10/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VM, Size 28 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 28DG/52WX-VXC60N000

3.54 (90) 2.64 (67)

0.47 (12) 1.77 (45)
Flange SAE 0.37 (9.5)
J744 101-2(B)) G1 G

3.70 (94)

2.74 (69.7)
2.6 (67.5)
L

2.35 (59.6)
DIA (ø101.6 h8)

45
°
.5
68

0.56 (14.3)
2.60 (66)
3.26 (83)
4.0000
3.9979

1.06
(27)
L1
5.75 (146)
6.77 (172)
4.53 (115)
4.32 (109.8)
G G1 2.0 (50.8)

A
(37.5) (37.5)
1.48 1.48

B
0.75 (19)

0.47 (12) 0.94 (23.8)

6.34 (161)
7.44 (189)

Shaft end
R splined 7/8in 13T 16/32DP1)
(SAE J744 - 22-4 (B))
1/4-20UNC-2B

0.63
(16)
ø7/8in

usable 0.98
spline length (25)
0.25 (6.3)
1.61
(41)
Ports
Tightening torque, max.2)
A, B Pressure port (high press. series, code 62) SAE J518C 3/4 in
Fixing thread ISO 68 3/8-16UNC-2B; 0.83 (21) deep 30 lb-ft (42 Nm)

L/L1 Case drain port (L1 plugged) ISO 11926 3/4-16 UNF-2B 116 lb-ft (160 Nm)
G,G1 Port for ext. contr. press. (G1 plugged) ISO 11926 7/16-20 UNF-2B; 0.47 (12) tief 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 11/28

Unit dimensions A10VM, Size 28 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 28HZX/52WX-VXC66N000
A10VM 28EZX/52WX-VXC66N000

3.54 (90) 4.09 (106)

0.47 (12) 3.50 (89)
Flange SAE 0.37 (9.5)

0.79 (20)
J744 101-2(B))

3.70 (94)
3.25 (82.5)
L
L
DIA (ø101.6 h8)

45°
2.60 (66) 1.89 (48)
)
8.5
(6
70
2.

0.56 (14.3)
3.27 (83)
4.0000
3.9979

1.06 L1
(27) 5.75 (146)
6.77 (172)

A10VM 28HZ.... A10VM 28EZ....

6.04 (153.5) 8.19 (208)

4.37 (111)
A A
1.22 1.22
(31) (31)

B B

0.47 (12)
6.34 (161)
7.44 (189)

Ports
Tightening torque, max.1)
A, B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 3/4-16 UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.39 (10) deep 29 lb-ft (40 Nm)
1) see safety information
12/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VM, Size 45 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 45DG/52WX-VXC60N000
A10VM 45DG/52WX-VXC61N000
2.87 (73)
1.93 (49)
45°
0.37 (9.5) 3.90 (99)
Flange SAE L1 G L1
J744 101-2(B))

4.04 (102.5)
L
DIA (ø101.6 h8)

3.07 (78)

3.03 (77)
L

3.07 (78)
2.60 (66)
G1

8)
(7
Z

07
3.

0.56 (14.3)
3.43 (87)
4.0000
3.9979

5.75 (146)
6.77 (172)
6.89 (175)
4.35 (110.5) View Z Port plate 61
1.18 (30)

(50 00
A

.8)
2.
(37.5) (37.5)
1.48 1.48

L1 B A
(50.8)

(50 00
2.00

.8)
2.
L
0.94 0. 0.
0.47 (12) (23.8) (23 94 (23 94
.8) 30° .8) 30°
1.50 1.50
(38) (38)

Shaft ends
R splined 1in 15T 16/32DP1) W splined 7/8in 13T 16/32DP1)
(SAE J744 - 25-4 (B-B)) (SAE J744 - 22-4 (B))
1/4-20UNC-2B

1/4-20UNC-2B

0.63 0.63
(16) (16)
ø7/8in
ø1in

usable 1.16 usable 0.98

spline length (29.5) spline length (25)
0.25 (6.3) 0.25 (6.3)
45.9 1.61 (41)

Ports
Tightening torque, max.2)
A, B Pressure port (high press. series, code 62) SAE J518C 3/4 in
Fixing thread ISO 68 3/8-16UNC-2B; 0.83 (21) deep 31 lb-ft (42 Nm)

L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
G, G1 Port for ext. control press. (G1 plugged) ISO 11926 7/16-20 UNF-2B; 12 deep 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 13/28

Unit dimensions A10VM, Size 45 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 45HZX/52WX-VXC66N000
A10VM 45EZX/52WX-VXC61N000

4.33 (110)
3.74 (95) 45°
3.90 (99)
Flange SAE L1
J744 101-2(B)) L1

4.04 (102.5)

3.03 (77)
L
(ø101.6 h8)

3.13 (79.5)
L

2.24 (57)

(14.3)
8)
(7
7
3.9979 DIA

3 .0

0.56
4.0000

3.43 (87) 5.75 (146)

6.77 (172)

A10VM 45HZX/52WX-VXC66N000 A10VM 45EZX/52WX-VXC61N000

0.37 (9.5) 6.50 (165) 8.58 (218.5)
1.18 (30)
X

4.53 (115)
A
1.34 1.34
(34) (34)

L1 L1

L
L B
0.47 (12) 7.44 (189)
6.89 (175)
8.07 (205)

Ports
Tightening torque, max.1)
A, B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.39 (10) deep 29 lb-ft (40 Nm)
1) see safety information
14/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VM, Size 63 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 63DG/52WX-VXC60N000

2.78 (70.5)
G 1.77 (45)
Flange SAE 4.61 (117)
J744 101-2(B)) L1

0.56 (14.3)
4.21 (107)
3.98 (101)
DIA (ø101.6 h8)

3.29 (83.5)
3.43 (87)

DUESE N02.105
09156493
FD6000
M6-1.0
001
--10
#
45°

2.56 (65)
8°
G1
Z

3.62 (92)
4.0000
3.9979

5)
8.
(7
09
3.
8.64 (219.5) 5.75 (146)
6.77 (172)

4.82 (122.5)
0.37 (9.5) 4.23 (107.5)
1.57 (40)

B A
ø19

A
(37.5) (37.5)
1.48 1.48
(50.8)
2.00

0.59 (15) 0.94 (23.8)

7.66 (194.5)

Shaft ends
R splined 1 1/4in 14T 12/24DP1) W splined 1in 15T 16/32DP1)
(SAE J744 - 32-4 (C)) (SAE J744 - 25-4 (B-B))
5/16-18UNC-2B

1/4-20UNC-2B

0.75 0.63
(19) (16)
ø1 1/4in

ø1in

usable 1.57 usable 1.14

spline length (40) spline length (29)
0.25 (6.3) 0.25 (6.3)
2.18 (55.4) 1.81 (45.9)

Ports
Tightening torque, max.2)
A/B Pressure port (high press. series, code 62) SAE J518C 3/4 in
Fixing thread ISO 68 3/8-16UNC-2B; 0.83 (21) deep 31 lb-ft (42 Nm)

L/L1 Case drain port (L1plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
G,G1 Port for ext. control press. (G1 plugged) ISO 11926 7/16-20 UNF-2B; 12 deep 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 15/28

Unit dimensions A10VM, Size 63 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 63HZX/52WX-VXC66N000
A10VM 63EZX/52WX-VXC60N000

4.35 (110.5)
45°
4.61 (117)
0.37 (9.5) 1.57 L1
Flange SAE (40)
J744 101-2(B)) L

4.21 (107)
4.02 (102)
(ø101.6 h8)

3.43 (87)
2.44 (62)

(14.3)
0.55
4.0000 DIA

3.62 (92)
3.9979

(7 .09
5)
3
8.
8.64 (219.5) 5.75 (146)
6.77 (172)

A10VM 63HZX/52WX-VXC66N000 A10VM 63EZX/52WX-VXC60N000

(Dimensions for ports see page 14)
6.50 (165)
8.64 (219.5)
X
(37.5) 3.57 (90.5)

A A
1.48 1.48 (37.5)

L1 L1

B B

7.66 (194.5)

Ports
Tightening torque, max.2)
A/B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 262 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20UNF-2B; 0.39 (10) deep 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
16/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VM, Size 85 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 85DG/52WX-VXC60N000

10.10 (256.5) 3.07 (78)

5.12 (130) 2.17 (55)
Flange SAE 1.57 G L1
L1 L
J744 127-2(C)) (40)

5.04 (128)

3.68 (93.5)
4.02 (102)

0.69 (17.5)
3.54 (90)
G1

3.43 (87)
5.0000 DIA (ø127 )

45°
h8

5)
(9
74
3.
4.9975

4.43 (112.4)
0.50 (12.7) 6.44 (163.5)
7.13 (181)
6.25 (158.7)
8.27 (210)

A (57.2)
2.25

(45)
1.77

L1
(ø25)
0.98

(45)
1.77

B
0.79 (20) 1.09 (27.8)
8.80 (223.5)

Shaft ends
R splined 1 1/2in 17T 12/24DP1) W splined 1 1/4in 14T 12/24DP1)
(SAE J744 - 38-4 (C-C)) (SAE J744 - 32-4 (C))
5/16-18UNC-2B
7/16-14UNC-2B

1.10 0.75
(28) (19)
ø1 1/4in
ø1 1/2in

usable 1.30
usable 1.65 spline length (33)
spline length (42) 0.25 (6.3)
2.44 (61.9) 2.18 (55.4)

Ports
Tightening torque, max.2)
A/B Pressure port (high press. series, code 62) SAE J518C 1 in
Fixing thread ISO 68 7/16-14UNC-2B; 0.87 (22) deep 48 lb-ft (66) Nm

L/L1 Case drain port (L1 plugged) ISO 11926 1 1/16-12 UN-2B 262 lb-ft (360 Nm)
G,G1 Port for ext. control press. (G1 plugged) ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 17/28

Unit dimensions A10VM, Size 85 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VM 85EZX/52WX-VXC60N000

Flange SAE 5.12 (130)

J744 127-2(C)) L1 L1
L
L

5.04 (128)

0.70 (17.5)

3.68 (93.5)
DIA (ø127h8)

3.54 (90)
45°

5)
(9
74
3.
4.43 (112.4)
5.0000
4.9975

10.10 (256.5) 7.13 (181)

8.27 (210)

4.84 (123)
0.5 (12.7) 1.57 (40)
B

B A
A
(57.2)
2.25

(45) (45)
1.77 1.77

L1

B
(Ø25)
0.98

0.79 (20) 1.09

8.80 (223.5) (27.8)

Ports
Tightening torque, max.2)
A/B Pressure port (high press. series, code 62) SAE J518C 1 in
Fixing thread ISO 11926 7/16-14UNC-2B; 0.87 (22) deep 48 lb-ft (66) Nm
L/L1 Case drain port (L1 plugged) ISO 11926 1 1/16-12 UN-2B 262 lb-ft (360 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
18/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VE, Size 28 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 28DG/52WX-VXF66N000

2.64 (67) 2.60 (66)

3.15 (80) 1.38 (35) 1.77 (45)

Y G1 G

3.70 (94)
3.25 (82.5)
3.31 (84)
L

2,74 (69.7)
2.35 (59.6)
DIA (ø 135 h8)
5.24 DIA (ø 133)

15°
4.35 DIA (ø 115)
2.68 DIA (ø 68)

ø14
31
L R

1.22
(31)
3.27 (83)
5.3150
5.3125

L1
45°

0.50 (12.7)
1.38 2.60 (66)
(35) 6.30 (160)
7.24 (184)
1.62 (41.2)
1.42
(36)
View Y
A 0.13 (3.4)

0.07 (1.9)
0.26 (6.5)
1.22 1.22
(31) (31)

0.47 (12)
3.43 (87)
4.53 (115)

Shaft end
R splined 7/8in 13T 16/32DP1)
(SAE J744 - 22-4 (B))
1/4-20UNC-2B

0.63
(16)
ø7/8in

usable 0.98
spline length (25)
1.37 (34.8)

Ports
Tightening torque, max.2)
A/B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 261 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 3/4-16 UNF-2B 116 lb-ft (160 Nm)
G,G1 Port for ext. control press. (G1 plugged) ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 19/28

Unit dimensions A10VE, size 28 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 28HZX/52WX-VXF60N000
A10VE 28EZX/52WX-VXF60N000
3.15 (80) 1.38 (35) 106

3.70 (94)

1.22 (31)
L

2.66 (67.5)
15°
5.3150 DIA (ø 135 )
h8

1.22 (31) 1.89 (48)

4.35 DIA (ø 115)
5.24 DIA (ø 133)

2.68 DIA (ø 68)

L L R

0.55 DIA (Ø14)

5.3125

3.27 (83)
L1
45°

0.50 (12.7)
1.38 (35) 2.60 (66) 2.60 (66)
6.30 (160)
7.24 (184)

A10VE 28HZ.... A10VE 28EZ....

89 5.63 (143)
X

4.37 (111)
A
89
50.8
37.5
37.5
50.8
Ø19

B
B
23.8
12
ViewY 87
111
0.075 (1.9)

0.134 (3.4)
0.256 (6.5)

Ports
Tightening torque, max.2)
A, B Pressure port (high press. series, code 62) SAE J518C 3/4 in
Fixing thread ISO 68 3/8-16 UNC-2B; 0.83 (21) deep 31 lb-ft (42) Nm
L/L1 Case drain port (L1 plugged) ISO 11926 3/4-16 UNF-2B 116 lb-ft (160 Nm)
X Pilot pressure port ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
20/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VE, Size 45 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 45DG/52WX-VXF60N000
A10VE 45DG/52WX-VXF61N000
2.99 (76) 2.60 (66)
1.93 (49) 0.67 (17)
3.43 (87.2) 1.10 (28)
G
Y
L

4.04 (102.5)

3.07 (78)
G1

3.07 (78)

2.60 (66)
19°
(ø135h8)
4.33 DIA (ø110)

1.89 (48)
2.80 DIA (ø71.7)

L L R
W
5.3150 DIA

1.89 (48)

0.55 DIA (ø14)

5.3125

3.43 (87)
40° L1

0.5 (12.7) 1.10 (28) 2.60 (66)

View Y 6.30 (160)
7.28 (185)
0.134
(3.4) 1.15 Viewt W Port plate 61
0.075 (1.9)

0.256 (6.5) (29.2)

4.04 (102.5)
.8)
A
(50
ø19

(37.5)

2.0
1.48

0.75 DIA (ø19)

A
(37.5)
1.48

B
2.83 (72)
2.0 (50.8)

.8)
(50
B

2.0
0.94 (23.8) 0. 0.
(23 94 (23 94
0.55 (14) .8) 30° .8) 30°
3.69 (93.7)
4.87 (123.7) 1.50 1.50
(38) (38)

Shaft ends
R splined 1in 15T 16/32DP1) W splined 7/8in 13T 16/32DP1)
(SAE J744 - 25-4 (B-B)) (SAE J744 - 22-4 (B))
1/4-20UNC-2B

1/4-20UNC-2B

0.63 0.63
(16) (16)
ø7/8 in
ø1in

usable 1.16 usable 0.98

spline length (29.5) spline length (25)
1.57 (39.8) 1.37 (34.8)

Ports
Tightening torque, max.2)
A/B Pressure port (high press. series, code 62) SAE J518C 3/4 in
Fixing thread ISO 68 3/8-16UNC-2B; 0.83 (21) deep 31 lb-ft (42 Nm)

L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
G,G1 Port for ext. control press. (G1 plugged) ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 21/28

Unit dimensions A10VE, Size 45 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 45HZX/52WX-VXF66N000
A10VE 45EZX/52WX-VXFXXN000

3.43 (87.2) 1.10 (28) 4.39 (111.5) 2.60 (66)

0.67 (17)
Y

4.04 (102.5)
L

3.13 (79.5)
5.3150 DIA (ø135 )
h8

1.89 (48) 2.24 (57)

19°

1.89 (48)
4.33 DIA (ø110)
2.80 DIA (ø71)

0.55 DIA (ø14)

L
5.3125

3.43 (87)
40° L1
0.5 (12.7) 1.10 2.60 (66)
(28) 6.30 (160)
7.28 DIA (ø185)

View Y A10VE 45HZ.... A10VE 45EZ....

0.134 (3.4) 3.74 (95) 5.87 (149)
0.256 (6.5)
0.075 (1.9)

4.59 (116.5)
3.80 (96.5)

A A
1.34 1.34
(34) (34)

B B

0.55 (14)
3.67 (93.7)
4.87 (123.7)

Ports
Tightening torque, max.2)
A/B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 262 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
22/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Unit dimensions A10VE, Size 63 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 63HZ/52WX-VXF60N000

3.55 (90.1) 1.57 (40) 4.45 (113) 2.78 (70.5)

3.86 (98) 0.67 (17)

4.33 (110)
3.98 (101)
L
6.2967 DIA (ø160h8)
4.92 DIA (ø 125)
3.15 DIA (ø 80)

45°

2.52
(64)

1.89
(48)
L

3.64 (92.4)

1.89
(48)

0.67 (ø 17)
6.2992

°
19

L1 2.78
0.61 (15.5) 1.57 (40) (70.5)
5.33 (135.4) 7.87 (200)
9.25 DIA (ø 235)
3.92 (99.5)
0.75 DIA (ø19)
X

View Y
A
(37.5)(37.5)

0.39 (10)
1.48 1.48

0.12 (3.15)
0.20 (5.2)
(50.8)
2.00

0.71 (18) 0.94 (23.8)

4.35 (110.4)

Shaft ends
R splined 1 1/4in 14T 12/24DP1) W splined 1in 15T 16/32DP1)
(SAE J744 - 32-4 (C)) (SAE J744 - 25-4 (B-B))
5/16-18UNC-2B

1/4-20UNC-2B

0.63
0.75
(16)
(19)
ø1 1/4in

ø1 in

1.14
usable spline 1.57 usable spline (29)
length (40) length
1.57 (39.9)
1.94 (49.4)

Ports
Tightening torque, max.2)
A/B Pressure port (high press. series, code 62) SAE J518 3/4 in
Fixing thread ISO 68 3/8-16UNC-2B; 0.83 (21) deep 31 lb-ft (42 Nm)

L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
X Pilot pressure port ISO 11926 7/16-20 UNF-2B 29 lb-ft (40 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 23/28

Unit dimensions A10VE, Size 63 Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
A10VE 63EZX/52WX-VXF66N000

3.54 (90) 6.02 (153) 4.72 (120) 2.78 (70.5)

1.57 (40) 0.67 (17)

Y L
19°

4.33 (110)
4.02 (102)
L
6.2992 DIA (Ø160 )
h8

4.92 DIA (Ø125)

Ø17
3.15 DIA (Ø80)

48
Z

1.89 (48)
3.62 (92)
6.2967

L1
45° 0.61 L1
(15.5) 1.57 2.78 (70.5)
(40) 7.87 (200)
9.25 DIA (Ø235)

B A
(37.5) (37.5)
1.48 1.48

View Y
0.39 (10)
0.20 (5.2)
0.71 (18)
4.33 (110)
0.124 (3.15)

Ports
Tightenig torque max.2)
A/B Pressure port ISO 11926 1 1/16-12UN-2B; 0.79 (20) deep 262 lb-ft (360 Nm)
L/L1 Case drain port (L1 plugged) ISO 11926 7/8-14 UNF-2B 175 lb-ft (240 Nm)
1) ANSI B92.1a-1996, 30° pressure angle, flat base, flank centering, fit class 5
2) see safety information
24/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Integrated flushing and boost press. relief valve, N007

The flushing and boost pressure relief valve is used in closed
circuits to flush an unacceptable heat load out of the circuit
and to maintain a minimum boost pressure level (fixed setting).
The valve is integrated into the port plate.
A built-in fixed orifice determines the flushing flow, which is
taken out of the low pressure side of the loop and directed into
the motor housing. It leaves the housing together with the case
drain flow. This combined flow must be replenished with fresh,
cool fluid by means of the boost pump.

Standard flushing flow

With a pressure of pND = 290 psi (20 bar) in the low pressure
side of the circuit and an orifice dia. of 0.063 in (ø1,6 mm) the
flushing flow amounts to 1.45 gpm (5,5 L/min) (Size 28 - 85).
Other orifice diameters can be ordered in clear text.
Further flushing flows for sizes 28 - 85 see table:

Flushing flow gpm (L/min) Orifice dia. in inches (mm)

0.92 (3,5) 0.047 (1,2)
1.45 (5,5) 0.063 (1,6)
2.38 (7,2) 0.071 (1,8)

Schematic
eg. A10VM..HZ/...N007

L L1 A

B
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 25/28

Speed pickup Before finalizing your design please

request a certified installation drawing.
Dimensions in inches (mm)
The version A10VM/E...D („prepared for speed pickup“) com- Schematic
prises gearing around the rotary unit.
In this case, the rotating cylinder barrel can provide a speed
dependent signal, which can be picked up by a suitable sensor A B
and processed for further evaluation. The sensor port will be
plugged for delivery.
This preparation for speed pickup does not include the neces-
sary working parts They must be ordered separately as a kit
with a corresponding part number .
Inductive speed sensor ID R 18/20-L250 (see RE 95130) and
mounting parts (spacer and 2 seals per kit) can be ordered D
separately under the following part numbers:

Size Part Nr. Number of teeth

28 R902428802 48 L L1
45 R902437557 48
63 R902428802 56
85 In preparation.

Dimensions port D

A10VM 28

2.4
0 (6
1) 25°
4.41 (112)

A10VM 45, 63 and 85

Size A1 A2 A3
45 3.78 2.72 45°
(96) (69,2)
63 5.53 2.80 57,5°
(140,5) (71)
85 5.12 3.59 45°
(130) (91,3) A3
2
A

A1

A10VE 45
2.7
2(

33°
69

1.73 (44)
.2)
26/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

Mounting position
The motor housing must be filled during start up and operation.
The drain line must be arranged, so that the housing cannot
empty itself when the motor is at standstill. The end of the drain
line must enter the tank below the minimum fluid level.
In all installation positions the highest case drain port must be
used to fill the housing and to connect the drail line.

In case of a vertical installation please consult us.

A10VM

A10VE
RA 91703/11.07 | A10VM/VE Bosch Rexroth Corporation 27/28

Notes
28/28 Bosch Rexroth Corporation A10VM/VE | RA 91703/11.07

General Notes
– The variable motor A10VM/VE was designed for operation in open and closed circuits.
– System design, installation and commissioning require trained technicians and tradesmen.
– All hydraulic ports can only be used for the fastening of hydraulic service lines.
– Tightening torques: The tightening torques, given in this data sheet represent maximum values and may not be exceeded
(max. values for the female threads in the motor castings). Please comply with the manufacturer’s infor-
mation regarding the maximum permissible tightening torques for the used fittings!
For fastening screws to ISO 11926 we recommend to check the permissible tightening torques in each
case acc. to VDI 2230 issue 2003.
– During and shortly after operation of a motor the housing and especially a solenoid can be extremely hot, avoid being burned.
Take suitable safety measures (eg. wear protective clothing).
– All given data, information or instructions must be adhered to!
— To prevent fretting corrosion we recomend permanent oil lubrication of the drive shaft spline.

Bosch Rexroth Corporation Bosch Rexroth Corporation © This document, as well as the data, specifications and other informations set
Axial & Radial Piston Units 2315 City Line Road forth in it, are the exclusive property of Bosch Rexroth AG. Without their consent
8 Southchase Court Bethlehem, PA 18017-2131 it may not be reproduced or given to third parties.
Fountain Inn, SC 29644-9018 USA The data specified above only serve to describe the product. No statements
USA Telephone (610) 694-8300 concerning a certain condition or suitability for a certain application can be de-
Telephone (864) 967-2777 Facsimile (610) 694-8467 rived from our information. The information given does not release the user from
Facsimile (864) 967-8900 www.boschrexroth-us.com the obligation of own judgment and verification. It must be remembered that our
products are subject to a natural process of wear and aging.
www.boschrexroth-us.com
Subject to change.