®

OPA1013

Precision, Single-Supply
DUAL OPERATIONAL AMPLIFIER

FEATURES APPLICATIONS
● SINGLE POWER SUPPLY OPERATION ● PRECISION INSTRUMENTATION
● INPUT VOLTAGE RANGE TO GROUND ● BATTERY-POWERED EQUIPMENT
● OUTPUT SWINGS NEAR GROUND ● BRIDGE AMPLIFIERS
● LOW QUIESCENT CURRENT: 550µA max ● 4-20mA CURRENT TRANSMITTERS
● LOW VOS: 300µV max ● VOLTAGE COMPARATOR
● LOW DRIFT: 2.5µV/°C max
● LOW IOS: 1.5nA max
● LOW NOISE: 0.55µVp-p, 0.1Hz to 10Hz

DESCRIPTION
The OPA1013 dual operational amplifier provides The OPA1013 is characterized for operation at both
precision performance in single power supply and low +5V (single supply) and ±15V power supplies. When
power applications. It is laser trimmed for low offset operated from a single supply, the input common-mode
voltage and drift, greatly reducing the large errors range includes ground and the output can swing to
common with LM324-type op amps. Input offset within 15mV of ground. Completely independent bias-
current is also trimmed to reduce errors in high im- ing networks eliminate interaction between the two
pedance applications. amplifiers—even when one is used as a comparator.
The OPA1013 is available in an 8-pin plastic DIP
specified for the 0°C to +70°C temperature range.
V+
3.3µA 8
Simplified Circuit 3.3µA 7.5µA
(Half of Dual)

2nd
Gain 22Ω
400Ω 0.9V 400Ω
Stage
Out
1, 7
In – In +
2, 6 3, 5

22Ω

V–
4
International Airport Industrial Park • Mailing Address: PO Box 11400 • Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd. • Tucson, AZ 85706
Tel: (520) 746-1111 • Twx: 910-952-1111 • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132

© 1990 Burr-Brown Corporation PDS-1059F Printed in U.S.A. December, 1994

SBOS005 This datasheet has been downloaded from http://www.digchip.com at this page
SPECIFICATIONS
ELECTRICAL
VS = ±15V, VCM = 0V, TA = +25°C unless otherwise noted.

OPA1013CN8 OPA1013DN8
PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS
Input Offset Voltage ±50 ±300 ±200 ±800 µV
Time Stability 0.5 * µV/Mo
Input Offset Current ±0.08 ±1.5 * * nA
Input Bias Current 7 30 * * nA
Voltage Noise, BW = 0.1 to 10Hz 0.55 * µVp-p
Noise Density, f = 10Hz 28 * nV/√Hz
f = 1kHz 25 * nV/√Hz
Current Noise Density, f = 10Hz 0.12 * pA/√Hz
Input Resistance: Differential 70 300 * * MΩ
Input Resistance: Common-Mode 4 * GΩ
Open-Loop Voltage Gain VO = ±10V, RL = 2kΩ 1.2 2.9 * * V/µV
VO = ±10V, RL = 600Ω 0.5 1.9 * * V/µV
Common-Mode Input Range +13.5 +13.8 * * V
–15 –15.3 * * V
Common-Mode Rejection VCM = +13.5 to –15V 97 114 * * dB
Power Supply Rejection VS = ±2 to ±18V 100 117 * * dB
Channel Separation VO = ±10V, RL = 2kΩ 120 137 * * dB
Voltage Output RL = 2kΩ ±12.5 ±14 * * V
Slew Rate 0.2 0.35 * * V/µs
Quiescent Current (per amplifier) ±0.35 ±0.55 * * mA

*Specification same as OPA1013CN8.

VS = +5V/0V, VCM = 0V, VO = +1.4V, TA = +25°C unless otherwise noted.

OPA1013CN8 OPA1013DN8
PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS
Input Offset Voltage ±90 ±450 ±250 ±950 µV
Input Offset Current ±3.0 ±2.0 * * nA
Input Bias Current 10 50 * * nA
Open-Loop Voltage Gain VO = 5mV to 4V 0.1 * V/µV
RL = 500Ω
Common-Mode Input Range +3.5 +3.8 * * V
0 –0.3 * * V
Voltage Output Low No Load 15 25 * * mV
Low RL = 600Ω to Ground 5 10 * * mV
Low ISINK = 1mA 200 350 * * mV
High No Load 4 4.4 * * V
High RL = 600Ω to Ground 3.4 4 * * V
Quiescent Current (per amplifier) 0.33 0.5 * * mA

*Specification same as OPA1013CN8.

TA = 0°C to +70°C, VS = ±15V, VCM = 0V unless otherwise noted.

OPA1013CN8 OPA1013DN8

PARAMETER CONDITION MIN TYP MAX MIN TYP MAX UNITS

Input Offset Voltage ±80 ±400 ±230 ±1000 µV

VS = +5/0V, VO = +1.4V ±110 ±570 ±280 ±1200 µV
Input Offset Voltage Drift(1) 0.4 2.5 0.7 5 µV/°C
Input Offset Current ±0.3 ±2.8 * * nA
VS = +5/0V, VO = +1.4V ±0.5 ±6 * * nA
Input Bias Current 9 38 * * nA
VS = +5/0V, VO = +1.4V 13 90 * * nA
Open-Loop Voltage Gain VO = ±10V, RL = 2kΩ 0.7 2.2 * * V/µV
Common-Mode Rejection VCM = +13 to –15V 94 113 * * dB
Power Supply Rejection VS = ±2 to ±18V 97 116 * * dB
Voltage Output RL = 2kΩ ±12.0 ±13.9 * * V
VO Low VS = +5/0V, RL = 600Ω 6 13 * * mV
VO High VS = +5/0V, RL = 600Ω 3.2 3.9 * * V
Quiescent Current (per amplifier) ±0.37 ±0.6 * * mA
VS = +5/0V, VO = +1.4V 0.34 0.55 * * mA

*Specification same as OPA1013CN8.

NOTE: (1) Guaranteed by design. This specification is established to a 98% confidence level.

OPA1013 2
DICE INFORMATION

PAD FUNCTION
1 Output A
2 –In A
3 +In A
4 V–
5 +In B
6 –In B
7 Output B
8 V+
4 Substrate Bias: –VS

MECHANICAL INFORMATION
MILS (0.001") MILLIMETERS
Die Size 112 x 100 ±5 2.84 x 2.54 ±0.13
Die Thickness 20 ±3 0.51 ±0.08
Min. Pad Size 4x4 0.10 x 0.10
Transistor Count 92
Backing Gold

OPA1013 DIE TOPOGRAPHY

CONNECTION DIAGRAM ABSOLUTE MAXIMUM RATINGS

Power Supply Voltage ....................................................................... ±22V
N8 — Plastic Package — Top View Differential Input Voltage ................................................................... ±30V
Input Voltage ...................................................................... V+ to (V–) –5V
Output Short Circuit (TA = 25°C) ............................................. Continuous
Operating Temperature: ....................................................... 0°C to +70°C
Storage Temperature .......................................................... –65 to +150°C
Out A 1 8 V+
Lead Temperature (soldering, 10s) ............................................... +300°C
A
–
+

–In A 2 7 Out B

B
–
ORDERING INFORMATION
+

+In A 3 6 –In B
MODEL PACKAGE TEMPERATURE RANGE
OPA1013CN8 Plastic DIP 0°C to +70°C
V– 4 5 +In B OPA1013DN8 Plastic DIP 0°C to +70°C

PACKAGE INFORMATION
PACKAGE DRAWING
MODEL PACKAGE NUMBER(1)
OPA1013CN8 Plastic DIP 006
OPA1013DN8 Plastic DIP 006
NOTE: (1) For detailed drawing and dimension table, please see end of data
sheet, or Appendix D of Burr-Brown IC Data Book.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.

3 OPA1013
TYPICAL PERFORMANCE CURVES
TA = +25°C unless otherwise noted.

OFFSET VOLTAGE
OFFSET VOLTAGE vs TEMPERATURE vs BALANCED SOURCE RESISTANCE
10
VS = ±15V R
200
+

Input Offset Voltage (mV)

–
Offset Voltage (µV)

100
1 R
V S = 5V/0V, 25°C

0.1
–100 V S = ±15V, 25°C

–200
6 Representative Devices
0.01
–50 –25 0 25 50 75 100 125 1k 3k 10k 30k 100k 300k 1M 3M 10M
Temperature (°C) Balanced Source Resistor (Ω)

COMMON-MODE REJECTION RATIO

OFFSET VOLTAGE vs TIME vs FREQUENCY
5 120
Common-Mode Rejection Ratio (dB)

VS = ±15V
Changes in Offset Voltage (µV)

100
4
V = ±15V
80
3
V = 5V/0V
60
2
Plastic DIP N8 Package 40

1
20

0 0
0 1 2 3 4 5 10 100 1k 10k 100k 1M
Time After Power On (Minutes) Frequency (Hz)

POWER SUPPLY REJECTION RATIO

vs FREQUENCY 0.1Hz TO 10Hz NOISE
120
VS = ±2V to ±18V
Power Supply Rejection Ratio (dB)

100
Noise Voltage (200nV/Div)

Negative
Supply
80

Positive
60
Supply

40

20

0
0.1 1 10 100 1k 10k 100k 1M 0 2 4 6 8 10
Frequency (Hz) Time (s)

OPA1013 4
 TYPICAL PERFORMANCE CURVES (CONT)
TA = +25°C unless otherwise noted.

NOISE DENSITY vs FREQUENCY 10Hz VOLTAGE NOISE DISTRIBUTION

1000 200
V = ±2V to ±18V VS = ±15V
180 340 units tested
Voltage Noise Density (nV/ Hz)
Current Noise Density (fA/ Hz)

160 from three runs.

300
140

Number of Units
Current 120
Noise
100 100
80
60
30
40
Voltage
20
Noise
10 0
1 10 100 1k 10 20 30 40 50 60
Frequency (Hz) Voltage Noise Density (nV/ Hz)

INPUT BIAS CURRENT

SUPPLY CURRENT vs TEMPERATURE vs COMMON-MODE VOLTAGE

Common-Mode Input Voltage, VS = +5V, 0V (V)

Common-Mode Input Voltage, VS = ±15V (V)
460 15 5
Supply Current per Amplifier (µA)

VS = ±15V 10 4
420

5 3
380
VS = 5V/0V
0 2
340 VS = ±15V VS = 5V/0V
–5 1

300
–10 0

260 –15 –1
–50 –25 0 25 50 75 100 125 0 –5 –10 –15 –20 –25 –30
Temperature (°C) Input Bias Current (nA)

INPUT OFFSET CURRENT INPUT BIAS CURRENT

vs TEMPERATURE vs TEMPERATURE
–1 –30
VCM = 0V

–25
–0.8
Input Offset Current (nA)

Input Bias Current (nA)

VS = 5V/0V VCM = 0V
V = ±2.5V
–20
–0.6
–15
V S = ±2.5V
–0.4 VS = ±15V
–10 V S = 5V/0V

–0.2
–5 V S = ±15V

0 0
–50 –25 0 25 50 75 100 125 –50 –25 0 25 50 75 100 125
Temperature (°C) Temperature (°C)

5 OPA1013
TYPICAL PERFORMANCE CURVES (CONT)
TA = +25°C unless otherwise noted.

OUTPUT SATURATION AND SINK CURRENT

vs TEMPERATURE OUTPUT SHORT CIRCUIT CURRENT vs TIME
10 50

Sourcing
+V = 5V to 30V 0°C VS = ±15V
40
–V = 0V
25°C

Output Short Circuit Current

ISINK = 10mA 30
Saturation Voltage (V)

20 70°C
1
ISINK = 5mA 10
0
ISINK = 1mA –10
0.1 –20 70°C
ISINK = 100µA
–30 25°C

Sinking
ISINK = 10µA
–40 0°C
ISINK = 0
0.01 –50
–50 –25 0 25 50 75 100 125 0 1 2 3
Temperature (°C) Time (Minutes)

VOLTAGE GAIN vs LOAD RESISTANCE VOLTAGE GAIN vs FREQUENCY

10M 140
VO = ±10V with VS = ±15V
CL = 100pF
VO = 20mV to 3.5V 120
VS = ±15V
with VS = 5V/0V 100
Voltage Gain (dB)
Voltage Gain

80
(1)
1M 60
VS = 5V/0V
40

(2) 20

100k –20
100 1k 10k 0.01 0.1 1 10 100 1k 10k 100k 1M 10M
Load Resistance to Ground (Ω ) Frequency (Hz)
NOTES: (1) TA = +25°C, VS = ±15V. (2) TA = +25°C, VS = 5V/0V.

GAIN AND PHASE vs FREQUENCY CHANNEL SEPARATION vs FREQUENCY

80 160
VCM = 0V VS = ±15V
20 CL = 100pF 100 VIN = 20Vp-p to 5kHz
140 RL = 2kΩ
Channel Separation (dB)

120 Limited by
Phase Shift (Degrees)

thermal
Voltage Gain (dB)

10 140 interaction
120
VS = ±15V Phase RS =100Ω
160
Gain
VS = ±15V 100 RS =1k
0 180
VS = 5V/0V VS = 5V/0V
200
80 Limited by
–10 220 pin-to-pin
capacitance
240 60
0.1 1 10 10 100 1k 10k 100k 1M
Frequency (MHz) Frequency (Hz)

OPA1013 6
TYPICAL PERFORMANCE CURVES (CONT)

SMALL SIGNAL TRANSIENT RESPONSE LARGE SIGNAL TRANSIENT RESPONSE

VS = ±15V, G = +1 VS = ±15V, G = +1

+50mV
+10V

0mV 0V

–10V
–50mV

VS = 5V/0V

SMALL SIGNAL TRANSIENT RESPONSE LARGE SIGNAL TRANSIENT RESPONSE

VS = 5V/0V, G = +1, RL = 600Ω to Ground VS = 5V/0V, G = +1, RL = 4.7kV to 5V

100mV 4V

50mV
FPO 2V
FPO
0V

0mV

Input = 0V to 4V Pulse

COMPARATOR RISE RESPONSE TIME

LARGE SIGNAL TRANSIENT RESPONSE 10mV, 5mV, 2mV Overdrives
VS = 5V/0V, G = +1, No Load

4V
Output (V) 2

2V

0V 0
Input (mV)

–100
Input = 0V to 4V Pulse VS = 5V/0V

7 OPA1013
TYPICAL PERFORMANCE CURVES (CONT)

COMPARATOR FALL RESPONSE TIME

10mV, 5mV, 2mV Overdrives

Output (V)
2

0
100
Input (mV)
0

VS = 5V/0V

APPLICATIONS INFORMATION INPUT PROTECTION

The circuitry of the OPA1013 is protected against overload
The OPA1013 is unity-gain stable, making it easy to use and for input voltages ranging from the positive supply voltage
free from oscillations in the widest range of circuitry. Follow to 5V below the negative supply voltage (below ground in
good design practice by bypassing the power supplies close
single supply operation). No external protection circuitry is
to the op amp pins. In most cases 0.1µF ceramic capacitors required, as it is with other common single-supply op amps.
are adequate.
Furthermore, the OPA1013 is free from phase-reversal prob-
lems common with other single-supply op amps. When the
SINGLE POWER SUPPLY OPERATION inputs are driven below ground (or below the negative
The OPA1013 is specified for operation from a single power power supply), the output polarity remains correct.
supply. This means that linear operation continues with the
input terminals at (or even somewhat below) ground poten-
tial. When used in a non-inverting amplifier, 0V input must COMPARATOR OPERATION
produce 0V output. In practice, the output swing is limited The OPA1013 functions well as a comparator, where high
to approximately 15mV above ground with no load. Output speed is not required. Sometimes, in fact, the low offset and
swing near ground can be optimized when the output load is docile characteristics of the OPA1013 may simplify the
connected to ground. If the output must sink current, the design of comparator circuitry. The two op amps in the
ability to swing near ground will be diminished. The output OPA1013 use completely independent bias circuitry to avoid
swings to within approximately 200mV of ground when interaction when the inputs are over-driven. Driving one op
sinking 1mA. amp into saturation will not affect the characteristics of the
other amplifier. The outputs of the OPA1013 can drive one
TTL load. Quiescent current remains stable when the inputs
are overdriven.

0-4mA In +VS 0-4mA Out

R3
+
100Ω
1/2 N channel enhancement MOSFET
OPA1013 Supertex, Siliconix, Motorola, etc.
– C1 or
0.001µF 2 x 2N2222

R4
R1 R2
500Ω
500Ω 50Ω

To Ground or –VS

FIGURE 1. Precision Current Mirror.

OPA1013 8
 V+
–
7

V1 + 5
– 1/2
OPA1013 2
–
6
VO
+ VO = V2 – V1
3
1
– Input common-mode range
INA105 extends to approximately
4 150mV above V– supply — limited
V2 +
1/2 by OPA1013 output swing.
+ V–
OPA1013

FIGURE 2. Instrumentation Amplifier.

V+

7 8
REF200
100µA
1 2 5
1/2
OPA1013 2
6
3 VO
– PMI VO = V2 – V1
V1 MAT03
Input 1
+
V2 INA105
1/2
OPA1013
V–
Input common-mode range extends
to approximately 200mV below V– supply.

FIGURE 3. Instrumentation Amplifier.

V+

VI
REF200 (+100mV)
100µA V+ (–100mV)

Output

1/2
1kΩ OPA1013
Output

TTL or
CMOS

1kΩ 1/2
OPA1013
VI

NOTE: VI must sink 100µA.

FIGURE 4. Window Comparator.

9 OPA1013
 IMPORTANT NOTICE

Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those
pertaining to warranty, patent infringement, and limitation of liability.

TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.

Customers are responsible for their applications using TI components.

In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.

TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.

Copyright  2000, Texas Instruments Incorporated