R

Grid-connected PV Inverter
SUN-�K-G�� SUN-�K-G�� SUN-�K-G��
SUN-�K-G�� SUN-�K-G�� SUN-�K-G��
SUN-�K-G�� SUN-��K-G�� SUN-��K-G��

User Manual
Contents
�. Introduction ………………………………………………………… - � -
�.� Appearance Introduction …………………………………………………… - � -
�.� Parts list ……………………………………………………………… - � -

�. Safety warnings and instructions ……………………………………… - � -

�.� Safety signs ………………………………………………… - � -
�.� Safety instructions ………………………………………………… - � -
�.� Notes for using …………………………………………………… - � -

�. Operation Interface ……………………………………………… - � -

�.� Interface View ………………………………………………………… - � -

�.� Status Indicator ……………………………………………………… - � -
�.� Buttons …………………………………………… - � -
�.� LCD Display ……………………………………………… - � -

�. Product installation …………………………………………………………… - � -

�.� Select installation location ………………………………………………… - � -
�.� Inverter Installation ………………………………………………… - �� -

�. Electrical Connection ……………………………………………………… - �� -

�.� PV Module Selection ……………………………………………… - �� -

�.� DC input terminal connection ……………………………………………… - �� -

�.� AC input terminal connection ……………………………………………… - �� -
�.� The connection of the ground line ………………………………………… - �� -
�.� Max. over current protection device ……………………………………… - �� -
�.� Inverter monitoring connection ………………………………………… - �� -
�.� Installation of datalogger …………………………………………………… - �� -
�.� Configuration of datalogger……………………………………………………… - �� -

�. Startup and Shutdown …………………………………………………… - �� -

�.� Start up the inverter ………………………………………………… - �� -

�.� Inverter Shutdown ………………………………………………………… - ��-
�.� Anti-PID Function(optional) ……………………………………………… - �� -
�. Zero-export function via energy meter …………………………… - �� -

�.� Use of zero-export function ………………………………………………… - �� -

�.� Sensor Clamp(optional) ……………………………………………… - �� -

�.� Use of limiter function ………………………………………………… - �� -

�.� How to browse the load power of your PV grid-tieplant on monitoring platform? - �� -
�. General Operation …………………………………………… - �� -

�.� The initial interface …………………………………………… - �� -

�.� Submenus in the Main Menu ……………………………………………… - �� -

�.� System param setting ……………………………………………… - �� -

�.� Running param setting ……………………………………………… - �� -

�.� Protect Param setting …………………………………………………… - �� -

�.� Comm. param setting …………………………………………………… - �� -

�. Repair and Maintenance ……………………………………………… - �� -

��. Error information and processing……………………………………… - �� -
��.� Error code ………………………………………………………… - �� -
��. Specification ……………………………………………………………… - �� -
About This Manual
The manual mainly describes the product information, guidelines for installation, operation and
maintenance. The manual cannot include complete information about the photovoltaic (PV) system.

How to Use This Manual

Read the manual and other related documents before performing any operation on the inverter.
Documents must be stored carefully and be available at all times. Contents may be periodically
updated or revised due to product development. The information in this manual is subject
to change without notice.The latest manual can be acquired via [email protected]

Photovoltaic Grid-connected System

PV array Inverter Metering Power grid

Family load
Application of inverter in photovoltaic power system

- �� -
�. Introduction
�.� Appearance Introduction
On-grid Inverter can convert solar panel DC power into AC power which can directly input to
the grid. Its appearance is shown below.These models contain SUN-�K-G��, SUN-�K-G��,
SUN-�K-G��, SUN-�K-G��, SUN-�K-G��, SUN-�K-G��, SUN-�K-G��, SUN-��K-G��,
SUN-��K-G��.
The following is collectively referred to as “inverter”.

Pic �.� Front view

Pic �.� Bottom view

- �� -
�.� Parts list

Please check the following table, to see whether all the parts are included in the package：

Mounting stainless steel

Grid-tied PV String Inverter Wall mounting bracket x� screws M���
x� x�

DC+/DC- Plug connectors Stainless steel anti-collision

AC power connectors x� including metal terminal bolt M���
xN x�

User
manual

User manual x� Datalogger (optional) x� Meter(optional)

x�

*Sensor Clamp(optional)
x�

- �� -
�. Safety warnings and instructions
Improper use may result in potential electric shock hazards or burns. This manual contains
important instructions that should be followed during installation and maintenance. Please
read these instructions carefully before use and keep them for future reference.

�.� Safety signs

Safety symbols used in this manual, which highlight potential safety risks and important
safety information, are listed as follows:

Warning:
Warning symbol indicates important safety instructions, which if not correctly
followed, could result in serious injury or death.

Shock Hazard:
Caution, risk of electric shock symbol indicates important safety instructions,
which if not correctly followed, could result in electric shock.

Safety Hint:
Note symbol indicates important safety instructions, which if not correctly
followed, could result in some damage or the destruction of the inverter.

High Temperature Hazard:

Caution, hot surface symbol indicates safety instructions, which if not correctly
followed, could result in burns.

�.� Safety instructions

Warning:
Electrical installation of the inverter must conform to the safety operation rules
of the country or local area.

Warning:
Inverter adopts non-isolated topology structure, hence must insure DC input and
AC output are electrical isolated before operating the inverter.

Shock Hazard:
Prohibit disassembling inverter case, there existing shock hazard, which may
cause serious injury or death, please ask qualified person to repair.

- �� -
 Shock Hazard:
When PV module is exposed to sunlight, the output will generate DC voltage.
Prohibit touching to avoid shock hazard.

Shock Hazard:
While disconnect the input and output of the inverter for maintenance, please
waits for at least � mins until the inverter discharge the remnant electricity.

High Temperature Hazard:

Local temperature of inverter may exceed ��℃ while under operating.
Please do not touch the inverter case.

�.� Notes for using

The single phase string power inverter is designed and tested under related safety regula-
tions. It can ensure the personal safety of the user. But as a electric device, it may cause
shock or injury by incorrect operation. Please operate the unit under below requirements:

�. Inverter should be installed and maintained by qualified person under local standard
regulations.
�. Must disconnect the AC side first, then disconnect DC side while doing installation and
maintenance, after that, please wait at least � mins to avoid getting shocked.
�. Local temperature of the inverter may exceed �� ℃ while under operating.Do not touch
to avoid getting injured.
�. All electrical installation must be in accord with local electrical standards, and after
obtaining the permission of the local power supply department, the professionals can
connect the inverter to the grid.
�. Please take appropriate anti-static measure.
�. Please install where children can not touch.
�. The steps to start the inverter：�) switch on the AC side circuit breaker, �) Switch on the DC
side circuit breaker of the PV panel. �) Turn on the DC switch of the inverter.
The steps to stop the inverter：�) switch off the AC side circuit breaker, �) switch off the DC side
circuit breaker of the PV panel. �) Turn off the DC switch of the inverter.
�. Don’t insert or remove AC and DC terminals when the inverter is in normal operation.
�. The DC input voltage of the inverter must not exceed the maximum value of the model.

- �� -
�. Operation Interface

�.� Interface View

DC AC Normal Alarm

Pic �.� Front panel display

�.� Status Indicator

There are four LED status indicator lights in the front panel of the inverter. Please see table �.�
for details.

Indicator status Explanation

on Inverter detects DC input
off

Low DC input voltage
on Grid Connected
off

Grid Unavailable
on Under normal operating
off

Stop operating
on Detected faults or report faults
off

Under normal operating

Table �.� Status indicator lights

- �� -
�.� Buttons

There are four keys in the front panel of the Inverter(from left to right): Esc, Up, Down and
Enter keys. The keypad is used for:

● Scrolling through the displayed options (the Up and Down keys);

● Access to modify the adjustable settings (the Esc and Enter keys).

Esc Up Down Enter

�.� LCD Display

The two-line Liquid Crystal Display (LCD) is located on the front panel of the Inverter, which
shows the following information:

● Inverter operation status and data;

● Service messages for operator;
● Alarm messages and fault indications.

- �� -
�. Product installation

4.1 Select installa�on loca�on

To select a location for the inverter, the following criteria should be considered:

WARNING: Risk of fire

● Do not install the inverter in areas containing highly flammable materials or gases.
● Do not install the inverter in potentially explosive atmospheres.
● Do not install in small closed spaces where air can not circulate freely. To avoid overheating,
always make sure the flow of air around the inverter is not blocked.
● Exposure to direct sunlight will increase the operational temperature of the inverter and
may cause output power limiting. It is recommended that inverter installed to avoid direct
sunlight or raining.
● To avoid overheating ambient air temperature must be considered when choosing the
inverter installation location. It is recommended that using a sun shade minimizing direct
sunlight when the ambient air temperature around the unit exceeds ���°F/��℃.

Pic �.� Recommended installation place

- �� -
● Install on a wall or strong structure capable of bearing the weight.
● Install vertically with a maximum incline of +/-��°. If the mounted inverter is tilted to an
angle greater than the maximum noted, heat dissipation can be inhibited, and may result in
less than expected output power.
● If install more than one inverter, must leave at least ���mm gap between each inverter. And
two adjacent inverters are also separated by at least ��� mm. And must install the inverter at
the place where children cannot touch. Please see picture �.�.
● Consider whether the installation environment is helpful to see the inverter LCD display and
indicator status clearly.
● Must offer a ventilate environment if inverter installed in the airtight house.

Safety Hint:
Do not place or store any items next to the inverter.

� �°

Pic �.� Installation Angle

- �� -
 ≥���mm

≥���mm

Pic �.� Installation Gap

�.� Inverter Installation

The inverter is designed according to the wall mounted type installation, please use the wall
mounted (the brick wall of the expansion bolt) when installing.

Anchoring

Mounting bracket

Stainless steel screws

Inverter

Pic �.� Inverter Installation

- �� -
Procedure shows below:
�. Locate on the appropriate wall according to the bolt position on the mounting bracket, then
mark the hole.On the brick wall, the installation must be suitable for the expansion bolt
installation.

Pic �.� Inverter hanging plate installation

�. Ensure that the position of the installation holes on the wall is in accordance with the
mounting plate, and the mounting rack is vertically placed.
�. Hang the inverter to the top of the mounting rack and then use the M� screw in the
accessory to lock inverter heat sink to the hanging plate, to ensure that the inverter will not
move.

Pic �.� Inverter installation

- �� -
5 Electrical Connec�on
�.� PV Module Selection:
When selecting proper PV modules, please be sure to consider below parameters:
�) Open circuit Voltage (Voc) of PV modules not exceeds max. PV array open circuit voltage of
inverter.
�) Open circuit Voltage (Voc) of PV modules should be higher than min. start voltage.
�) The PV modules used to connected to this inverter shall be Class A rating certified according
to lEC �����.

Inverter Model �KW �KW �KW �KW �KW �KW �KW ��KW ��KW

PV Input Voltage ���V (���V~����V)

PV Array MPPT Voltage Range ���V~����V

No. of MPP Trackers �

No. of Strings per MPP Tracker �+�

�.� DC input terminal connection

�. Switch the Grid Supply Main Switch(AC)OFF.
�. Switch the DC lsolator OFF.
�. Assemble PV input connector to the inverter.

Warning:
When using PV modules, please ensure the PV+ & PV- of solar panel is not
connected to the system ground bar.
Safety Hint:
Before connection, please make sure the polarity of the output voltage of PV
array matches the “DC+” and “DC-” symbols.
Warning:
Before connecting inverter, please make sure the PV array open circuit voltage is
within the ����V of the inverter.

Pic �.� DC+ male connector Pic �.� DC- female connector

- �� -
 Safety Hint:
Please use approved DC cable for PV system.

Cross section（mm ）
Cable type
Range Recommended value
Industry generic PV cable �.�~�.�
�.�(��AWG)
(model: PV�-F) (��~��AWG)

Table �.� DC Cable Specifications

The steps to assemble the DC connectors are listed as follows:
a) Strip off the DC wire about �mm, disassemble the connector cap nut (see picture �.�).

�mm

�mm

Pic �.� Disassemble the connector cap nut

b) Crimping metal terminals with crimping pliers as shown in picture �.�.

Crimping plier

Pic �.� Crimp the contact pin to the wire

c) Insert the contact pin to the top part of the connector and screw up the cap nut to the top
part of the connector. (as shown in picture �.�).

Pic �.� connector with cap nut screwed on

- �� -
d) Finally insert the DC connector into the positive and negative input of the inverter,shown as
picture �.�.

Pic �.� DC input connection

Warning:
Sunlight shines on the panel will generate voltage, high voltage in series may
cause danger to life. Therefore, before connecting the DC input line, the solar
panel needs to be blocked by the opaque material and the DC switch should
be 'OFF', otherwise, the high voltage of the inverter may lead to life-
threatening conditions.

Warning:
Please use its own DC power connector from the inverter accessories. Do not
interconnect the connectors of different manufacturers. Max. DC input current
should be ��A. if exceeds, it may damage the inverter and it is not covered by
Deye warranty.

�.� AC input terminal connection

Do not close the DC switch after the DC terminal is connected.Connect the AC terminal to the
AC side of the inverter, the AC side is equipped with Three phase AC terminals that can be
conveniently connected. Flexible cords are recommended for easy installation. The are as
shown in Table �.�.

Warning:
Prohibit using a single circuit breaker for multiple inverters, prohibit the
connection of load between inverter circuit breakers.

- �� -
 Model Cable CSA Cable outer dia AWG Breaker Max cable length

SUN-�K/�K/�K/�K Outside cable

�mm² ��-��mm �� ��A/���V
/�K/�K/�K/��K-G�� (�+N+PE)��m

Outside cable
SUN-��K-G�� �mm² ��-��mm �� ��A/���V
(�+N+PE)��m

Table �.� Cable information

The AC output connector is divided into three parts: matching socket, sleeve and sealingsleeve,
as shown in picture �.�, the steps are as follows:

Step �: Remove the cable sealing ring and sleeve in sequence from the AC connector.
Step �: Use strippers to strip the protective sheath and insulation layer of the AC cable to the
right length, as shown in Picture �.�.

� � � �
�. Matching socket �.Sleeve �.Sealing core �.Sealing nut

Pic �.� AC connector structure

Step �: Insert the cable (L�, L�, L�, N，PE) into the sealing sleeve.

��mm

�~��mm

Pic �.� Strip AC cable

Warning:
Be careful to distinguish the L�, L�,L�,N and PE of the AC cables.

- �� -
Step �: Use the hexagon screwdriver, loosen the bolts of the socket in turn, and insert each
cable core into the corresponding jack, and set each screw. The connection hole of AC
connection terminal labeling is shown in Picture �.�.

Pic �.� AC Connector Hole Pattern

Step �: Set the sleeve and sealing ring in place.

Step �: Connect the terminals to the inverter as shown in picture �.��.

Pic �.�� AC input connection

- �� -
�.� The connection of the ground line
Good grounding is good for resisting surge voltage shock and improving EMI performance.There-
fore, before connecting AC, DC and communication cables, you need to ground the cable firstly.
For a single system, just ground the PE cable. For multiple machine systems, all PE cables of the
inverter need to be connected to the same grounding copper platoon to ensure the equipoten-
tial connection. The installation of the shell ground wire is shown as picture �.��.

Pic �.��The installation of the shell ground wire

Model Wire Size Cable(mm�) Torque value(max)

�/�/�/�/�/�/�KW ��AWG �.�mm� �.�Nm

��/��KW ��AWG �mm� �.�Nm

Warning:
Inverter has built-in leakage current detection circuit, If an external leakage
current protection device is connected, its operating current must be greater
than ��� mA or higher, otherwise inverter may not work properly.

- �� -
�.� Max. over current protection device
In order to protect the inverter AC connection, it is recommended to install a circuit breaker to
prevent overcurrent. See table �.� below.

Rated output Rated output Current for protection

Inverter
voltage(V) current(A) device(A)

SUN-�K-G�� ���/��� �.�/�.�A ��

SUN-�K-G�� ���/��� �.�/�.�A ��
SUN-�K-G�� ���/��� �.�/�.�A ��
SUN-�K-G�� ���/��� �.�/�.�A ��
SUN-�K-G�� ���/��� ��.�/��.�A ��
SUN-�K-G�� ���/��� ��.�/��.�A ��
SUN-�K-G�� ���/��� ��.�/��.�A ��
SUN-��K-G�� ���/��� ��.�/��.�A ��
SUN-��K-G�� ���/��� ��.�/��.�A ��

Table �.� Recommended current protector specifications

�.� Inverter monitoring connection

Inverter has the function of wireless remote monitoring. The inverter with Wi-Fi function is
equipped with Wi-Fi Plug to connect the inverter and network. Wi-Fi Plug's operation, installa-
tion, Internet access, APP downloading and other processes are detailed in the instructions.

Phone

GPRS

Router Web Server

WIFI

PC

Pic �.�� Internet monitoring solution

- �� -
�.� Installation of datalogger

When installing the WiFi stick, tear off the sealing strip on the inverter. Insert the datalogger
into the interface and fix it with a screw. The configuration of the datalogger needs to be
performed after various electrical connections have been completed and the inverter DC
power on. When the inverter is on the DC power, it is determined whether the datalogger is
normally electrified (The LED light shines out of the shell).

Pic �.�� Datalogger installation diagram

�.� Configuration of datalogger

For the configuration of datalogger, please refer to illustrations of the datalogger.

�. Startup and Shutdown

Before starting the inverter, make sure that the inverter can meet the following conditions,
otherwise it may result in fire or damage to the inverter. In this case, we do not undertake
any responsibility. At the same time, to optimize the system configuration, it is recommended
that the two inputs be connected to the same number of photovoltaic modules.

a). The maximum open circuit voltage of each set of photovoltaic modules shall not exceed
����Vdc under any conditions.

b). Each input of the inverter better use the same type of photovoltaic module in series.

c). Total output power of PV shall not exceed the maximum input power of inverter, each
photovoltaic modules shall not exceed the rated power of each channel.

- �� -
�.� Start up the inverter

When starting up the three phase string inverter, should fellow steps below：

�. Starting switch on the AC breaker.

�. Turn on the DC switch of the photovoltaic module, and if the panel provides sufficient
starting voltage and power, the inverter will start.

�. The inverter will first check the internal parameters and the grid parameters, while the
liquid crystal will show that the inverter is self-checking.

�. If the parameter is within acceptable range, the inverter will generate energy.
NORMAL indicator light is on.

�.� Inverter Shutdown

Must follow below steps while shutting down the inverter:

�. Switch off the AC breaker.

�. Wait for �� seconds, turn off the DC switch (if any), or simply disconnect the DC input
connector. The inverter will close the LCD and all LED within two minutes.

�.� Anti-PID Function(option)

Inverter
PV+

... PV- V+
R

S
PID
T
V-

PE

The Anti-PID module repairs the PID effect of the PV module at night.The PID module always
runs when connected to AC.
If maintenance is required and turn off the AC switch can disable the Anti-PID function.

Warning:
The PID functionality is automatic.When the DC bus voltage is below ��VDC, the PID module
will create ���VDC between the PV and ground.No control and equipment are required.

Warning:
If you need to maintain the inverter, Please turn off the AC switch first,then turn off the DC switch,
and wait � minutes before you do other operations.

- �� -
7. Zero-export func�on via energy meter
There're two kinds of energy meters for this series inverter. First type is Eastron SDM���-Mod-
bus V� which is able to measure the Max. ���A current directly. More details please refer to Pic
�.� & �.�. For the Eastron SDM��� MCT ��mA, it needs external CT to measure the current. The
CT power range is from �A-����A. More details about the Eastron SDM��� MCT, please refer to
Pic �.� & �.�. Also, the CHNT meter DTSU��� is supported, it can measure the Max. ��A current
directly. More details about the DTSU���, please refer to Pic �.� & �.��.
When you are reading this, we believe that you have completed the connection according to
the requirements of chapter �, if you have been running your inverter at this time, and you
want to use the zero-export function, please turn off AC and DC switch of the inverter, and
wait for � minutes until the inverter completely discharged.Please follow below Picture �.�
to connect the energy meter.
For system wiring diagram, the red line refers to L line (L�, L�, L�), the black line refers to the
neutral line (N). Connecting energy meter RS��� cable to inverter's RS��� port. It's recommended
to install an AC switch between the inverter and the utility grid, the specs of the AC switch are
determined by the power of load.
If there is no integrated DC switch inside the inverter you purchased, we commend you to
connect the DC switch. The voltage and current of the switch depend on the PV array you access.

- �� -
 � � � � � � � �
L� N
L� L�
Eastron
L� L�
N L�
Gird Load
(�,�,�,�) (�,�,�,�)

B A G
5 6 7 8
RS ���
RS���B RS���A GND

Eastron SDM���-Modbus V�
Pic �.� Eastron meter

Inverter
Solar Panel array

AC Breaker
RS ���
Male
connector L� L� L� N

Family load
VCC_�V ���_B
N L� L� L�
RS ���
Female connector L� L� L� N

GND ���_A
meter

L� L� L� N
5 6 7 8

� ���_A L� L� L� N
���_B
�

� RS��� Communication
GND

Pic �.� Connection diagram of Eastron meter Grid

Warning:
In final installation, breaker certified according to IEC �����-� and IEC �����-� shall be installed
with the equipment.

- �� -
 � � � � � � � �
L� N
L� L�
Eastron
L� L�
N L�
Gird Load
(�,�,�,�) (�,�,�,�)

B A G
5 6 7 8
RS ���
RS���B RS���A GND

Eastron SDM���-Modbus V�
Pic �.� Eastron meter

Inverter
Solar Panel array

AC Breaker
RS ���
Male
connector L� L� L� N

Family load
VCC_�V ���_B
N L� L� L�
RS ���
Female connector L� L� L� N

GND ���_A
meter

L� L� L� N
5 6 7 8

� ���_A L� L� L� N
���_B
�

� RS��� Communication
GND

Generator

Pic �.� Connection diagram of Eastron meter

- �� -
 � �� �� �� �� �� �� �� �� �� �� ��

L�
P� P�

� P HA S E � W IR E
Eastron L�
P� P� S � S�

U/I
L�
P� P� S � S�

M S� S�
N
P
� � � � � � �� �� �� �� �� ��
E
Grid voltage Auxiliary Current inputs
sampling power supply

�� �� ��
� � � � � � � �

RS ���
Eastron SDM���MCT RS485A RS485B GND
Pic �.� Eastron meter

Inverter
Solar Panel array

AC Breaker

RS ���

N L� L� L�
Male connector

Family load
black line

VCC_�V ���_B
White line

CT�

RS ���
black line

White line

Female
CT�
black line

connector
White line

CT�

GND ���_A
GND B A S� S� S� S� S� S�
9 1 0 11 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0

U/I ESC

P
M

Note: the arrow direction

E

towards the inverter

N L� L� L� LA NA
�
�
�
�
�

�
�

���_A
�

���_B
meter
�

L� L� L� N
� RS��� Communication
GND

Grid
Pic �.� Connection diagram of Eastron meter

- �� -
 � �� �� �� �� �� �� �� �� �� �� ��

L�
P� P�

� P HA S E � W IR E
Eastron L�
P� P� S � S�

U/I
L�
P� P� S � S�

M S� S�
N
P
� � � � � � �� �� �� �� �� ��
E
Grid voltage Auxiliary Current inputs
sampling power supply

�� �� ��
� � � � � � � �

RS ���
Eastron SDM���MCT RS485A RS485B GND
Pic �.� Eastron meter

Inverter
Solar Panel array

AC Breaker

RS ���

N L� L� L�
Male connector

Family load
black line

VCC_�V ���_B
White line

CT�

RS ���
black line

White line

Female
CT�
black line

connector
White line

CT�

GND ���_A
GND B A S� S� S� S� S� S�
9 1 0 11 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0

U/I ESC

P
M

Note: the arrow direction

E

towards the inverter

N L� L� L� LA NA
�
�
�
�
�

�
�

���_A
�

���_B
meter
�

L� L� L� N
� RS��� Communication
GND

Generator

Pic �.� Connection diagram of Eastron meter

- �� -
 � � � ��
� � � � � � ��

L�
Grid L� Load
(�,�,�,��)
Three-Phase Smart Meter

(�,�,�,��) L�
N
SET ESC

�� ��
RS ���
�� ��

� � � ��

CHNT DTSU���
Pic �.� CHNT meter

Inverter
Solar Panel array

AC Breaker

RS ���
Male connector
N L� L� L�

L� L� L� N Family load
VCC_�V 485_B

RS 485
Female connector
meter
GND 485_A

L� L� L� N
� ���_A
���_B
�

� RS��� Communication

Grid

Pic �.�� Connection diagram of CHNT meter

- �� -
 � � � ��
� � � � � � ��

L�
Grid L� Load
(�,�,�,��)
Three-Phase Smart Meter

(�,�,�,��) L�
N
SET ESC

�� ��
RS ���
�� ��

� � � ��

CHNT DTSU���
Pic �.�� CHNT meter

Inverter
Solar Panel array

AC Breaker

RS ���
Male connector
N L� L� L�

L� L� L� N Family load
VCC_�V 485_B

RS 485
Female connector
meter
GND 485_A

L� L� L� N
� ���_A
���_B
�

� RS��� Communication
Generator

Pic �.�� Connection diagram of CHNT meter

- �� -
 � � � ��
� � � �� �� �� �� �� �� ��

L�
Three-Phase Smart Meter
L�
���/���V,
L�
N
�~���A/��mA
��/��Hz

SET ESC

�� ��
Phase A current =�.���A
�� �� �� �� �� �� �� �� A B
RS���
� � � ��

Phase B current =�.���A

CHNT DTSU���
�x���/���V Phase C current =�.���A

���A/��mA Pic �.�� CHINT meter

Inverter
Solar Panel array

AC Breaker
RS ���
Male connector N L� L� L�

Home load
VCC_5V 485_B � � � ��

RS 485
Female connector ���/���V,
Three-Phase Smart Meter
L�L�L�N
GND 485_A
�~���A/��mA
��/��Hz

SET ESC

�� �� �� �� �� �� �� ��

� � � ��

Black line

White line
Black line

�
White line

���_A
Black line

White line

Note: the arrow direction

�

���_B towards the inverter

�

RS��� Communication
L�L�L�N

Grid

Pic �.�� Connection diagram of CHNT meter

- �� -
 � � � ��
� � � �� �� �� �� �� �� ��

L�
Three-Phase Smart Meter
L�
���/���V,
L�
N
�~���A/��mA
��/��Hz

SET ESC

�� ��
Phase A current =�.���A
�� �� �� �� �� �� �� �� A B
RS���
� � � ��

Phase B current =�.���A

CHNT DTSU���
�x���/���V Phase C current =�.���A

���A/��mA Pic �.�� CHINT meter

Inverter
Solar Panel array

AC Breaker
RS ���
Male connector N L� L� L�

Home load
VCC_5V 485_B � � � ��

RS 485
Female connector ���/���V,
Three-Phase Smart Meter
L�L�L�N
GND 485_A
�~���A/��mA
��/��Hz

SET ESC

�� �� �� �� �� �� �� ��

� � � ��

Black line

White line
Black line

�
White line

���_A
Black line

White line

Note: the arrow direction

�

���_B towards the inverter

�

RS��� Communication
L�L�L�N

Generator

Pic �.�� Connection diagram of CHNT meter

- �� -
�.� Multiple strings and parallel connection meters

This application is that when the string inverters work in parallel, there is only one power grid
and one load, and only one meter can be connected to prevent reverse current, so only this
many-to-one anti-reverse current connection can be connected.
If there’s several inverters in a plant, also it can use �pcs meter to realize zero export function.
For example,if there’s �pcs inverter in the system with �pcs meter.We need to setup �pcs
inverter as the master and others setup as slaves. And, all of them need to connect to the meter
via RS���. Below is the system diagram and configuration of the system.

Meter OFF << Exp_Mode AVG <<

Limiter OFF CT Ratio 0
MFR ACREL Shunt OFF
FeedIn 0.0KW << ShuntQTY 1 <<
Generator ON G.MFR CHNT
G.CT 1 << G.Pout 0% <<
G.Cap 0.0KW
Back<<
Pic �.�� Meter function

- �� -
 Name Description Range

AVG: Average power of three phase is zero exported.

MIN: Phase with minimum load power is zero
Exp_Mode AVG/MIN
exported, while the other two phase may be
in purchase mode.

CT ratio of power grid side meter when extern CT is

CT_Ratio �-����
applied.

Manufacturer of the grid side meter. Modbus AUTO/CHNT/

MFR Address of it should be set as ��. EASTRON

Percentage of the Feed in power exported to the

Feedin grid. �-���%

Parallel mode. Set one inverter as Master, others OFF/Master/

Shunt are Slave. ONLY need to set the master, Slave will Slave
follow the settings in the master.

ShuntQTY Number of inverters in parallel �-��

Generator DG side meter function Enable/Disable ON/OFF

CT ratio of power DG side meter when extern CT is

G.CT applied. �-����

Manufacturer of the DG side meter. Modbus AUTO/CHNT/

G.MFR Address of it should be set as ��. EASTRON

G.Cap Capacity of the DG. �-���kW

Note: Select Meter option in Run Param and long press ENTER button to enter this
Meter Setting page.

- �� -
 � � � � � � � �
L� N
L� L�
Eastron
L� L�
N L�
Gird Load
(�,�,�,�) (�,�,�,�)

B A G
5 6 7 8
RS ���
RS���B RS���A GND

Eastron SDM���-Modbus V�
Pic �.�� Eastron meter

Master(Mst) Grid
RS��� L�L�L� N

� ���_B
�

� ���_A

meter
GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A
GND

GND

5 6 7 8

L� L� L� N

� �
VCC_�V ���_B

RS ���
�

� �
Female connector
Slave�(Slv�) Slave�(Slv�)
RS��� RS���
GND ���_A

AC Breaker
L�
L�
L�
N
Master(Mst) load
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

Pic �.�� Eastron Connection diagram(The pass-through table)

- �� -
 � � � � � � � �
L� N
L� L�
Eastron
L� L�
N L�
Gird Load
(�,�,�,�) (�,�,�,�)

B A G
5 6 7 8
RS ���
RS���B RS���A GND

Eastron SDM���-Modbus V�
Pic �.�� Eastron meter

Generator
Master(Mst)
RS��� L�L�L� N

� ���_B
�

� ���_A

meter
GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A
GND

GND

5 6 7 8

L� L� L� N

� �
VCC_�V ���_B

RS ���
�

� �
Female connector
Slave�(Slv�) Slave�(Slv�)
RS��� RS���
GND ���_A

AC Breaker
L�
L�
L�
N
Master(Mst) load
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

Pic �.�� Eastron Connection diagram(The pass-through table)

- �� -
 � �� �� �� �� �� �� �� �� �� �� ��

L�
P� P�

� P HA S E � W IR E
Eastron L�
P� P� S � S�

U/I
L�
P� P� S � S�

M S� S�
N
P
� � � � � � �� �� �� �� �� ��
E
Grid voltage Auxiliary Current inputs
sampling power supply

�� �� ��
� � � � � � � �

RS ���
Eastron SDM���MCT RS485A RS485B GND
Pic �.�� Eastron meter

Master(Mst)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load

black line

VCC_�V ���_B
White line

CT�
black line
White line

RS ���
CT�
black line

Female connector
White line

CT�

GND ���_A Note: the arrow direction

towards the inverter

L� L� L� N
�� ��
GND B A S�S�S�S�S�S�

U/I

�
M

E
� �� �� �� �� �� �� �� �� ��

N L� L� L� LA NA
�
�
�

Master(Mst)
Eastron

�
�

RS���
�

Grid meter Grid

� ���_B
�

� ���_A

GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A
GND

GND

� �
�

� �

Slave�(Slv�) Slave�(Slv�)
RS��� RS���

Pic �.�� Connection diagram(Three-phase electricity )

- �� -
 � �� �� �� �� �� �� �� �� �� �� ��

L�
P� P�

� P HA S E � W IR E
Eastron L�
P� P� S � S�

U/I
L�
P� P� S � S�

M S� S�
N
P
� � � � � � �� �� �� �� �� ��
E
Grid voltage Auxiliary Current inputs
sampling power supply

�� �� ��
� � � � � � � �

RS ���
Eastron SDM���MCT RS485A RS485B GND
Pic �.�� Eastron meter

Master(Mst)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load

black line

VCC_�V ���_B
White line

CT�
black line
White line

RS ���
CT�
black line

Female connector
White line

CT�

GND ���_A Note: the arrow direction

towards the inverter

L� L� L� N
�� ��
GND B A S�S�S�S�S�S�

U/I

�
M

E
� �� �� �� �� �� �� �� �� ��

N L� L� L� LA NA
�
�
�

Master(Mst)
Eastron

�
�

RS���
�

Generator
Grid meter
� ���_B
�

� ���_A

GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A
GND

GND

� �
�

� �

Slave�(Slv�) Slave�(Slv�)
RS��� RS���

Pic �.�� Connection diagram(Three-phase electricity )

- �� -
 � � � ��
� � � � � � ��

L�
Grid L� Load
(�,�,�,��)
Three-Phase Smart Meter

(�,�,�,��) L�
N
SET ESC

�� ��
RS ���
�� ��

� � � ��

CHNT DTSU���
Pic �.�� CHNT meter

Master(Mst)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load
VCC_�V ���_B

RS ���
Female connector

GND ���_A

Master(Mst)
RS��� � � � ��

�
Three-Phase Smart Meter

���_B
�

SET ESC

� ���_A �� ��

GND
� � � ��
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A

L� L� L� N

Slave1(Slv1) Slave2(Slv2)
R S 485 R S 485

Grid
Pic �.�� CHNT Connection diagram(The pass-through table)

- �� -
 � � � ��
� � � � � � ��

L�
Grid L� Load
(�,�,�,��)
Three-Phase Smart Meter

(�,�,�,��) L�
N
SET ESC

�� ��
RS ���
�� ��

� � � ��

CHNT DTSU���
Pic �.�� CHNT meter

Master(Mst)
AC Breaker
L�
L�
L�
N
Solar Panel array
Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�) AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load
VCC_�V ���_B

RS ���
Female connector

GND ���_A

Master(Mst)
RS��� � � � ��

�
Three-Phase Smart Meter

���_B
�

SET ESC

� ���_A �� ��

GND
� � � ��
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A

L� L� L� N

Slave1(Slv1) Slave2(Slv2)
R S 485 R S 485 Generator

Pic �.�� CHNT Connection diagram(The pass-through table)

- �� -
 � � � ��
� � � �� �� �� �� �� �� ��

L�
Three-Phase Smart Meter
L�
���/���V,
L�
N
�~���A/��mA
��/��Hz

SET ESC

�� ��
Phase A current =�.���A
�� �� �� �� �� �� �� �� A B
RS���
� � � ��

Phase B current =�.���A

CHNT DTSU���
�x���/���V Phase C current =�.���A

���A/��mA Pic �.�� CHINT meter

Master(Mst)

AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load
VCC_�V ���_B

RS ��� L� L� L� N
� � � ��

Female connector ���/���V,

�~���A/��mA
Three-Phase Smart Meter

��/��Hz

SET ESC

GND ���_A �� �� �� �� �� ��

� � �
�� ��

��

Master(Mst)
Black line

White line

RS���
Black line

White line

Black line

White line

� ���_B
�

� ���_A

GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A

L� L� L� N
� �
�

� �

Slave1(Slv1) Slave2(Slv2)
R S 485 R S 485

Grid

Pic �.�� CHNT Connection diagram(The pass-through table)

- �� -
 � � � ��
� � � �� �� �� �� �� �� ��

L�
Three-Phase Smart Meter
L�
���/���V,
L�
N
�~���A/��mA
��/��Hz

SET ESC

�� ��
Phase A current =�.���A
�� �� �� �� �� �� �� �� A B
RS���
� � � ��

Phase B current =�.���A

CHNT DTSU���
�x���/���V Phase C current =�.���A

���A/��mA Pic �.�� CHINT meter

Master(Mst)

AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array Slave�(Slv�)
AC Breaker
L�
L�
L�
N
Solar Panel array

AC Breaker
L�
L�
L�
N
load
VCC_�V ���_B

RS ��� L� L� L� N
� � � ��

Female connector ���/���V,

�~���A/��mA
Three-Phase Smart Meter

��/��Hz

SET ESC

GND ���_A �� �� �� �� �� ��

� � �
�� ��

��

Master(Mst)
Black line

White line

RS���
Black line

White line

Black line

White line

� ���_B
�

� ���_A

GND
(as short as possible)

(as short as possible)

(as short as possible)

(as short as possible)

���_B

���_B
���_A

���_A

L� L� L� N
� �
�

� �

Slave1(Slv1) Slave2(Slv2)
R S 485 R S 485
Generator

Pic �.�� CHNT Connection diagram(The pass-through table)

- �� -
�.� Use of zero-export function
When the connection is completed, the following steps should be refered to use this function:
�. Turn on the AC switch.
�. Turn on the DC switch, waiting for the inverter's LCD is turned on.
�. Press Enter button on the LCD panel in the main interface into the menu options, select
[parameter setting] to enter setup submenu, and then select [running parameters] as shown
in picture �.��, at this time please input the default password ���� through pressing the
button [up down, enter], enter the operation parameter setting interface, shown as
picture �.��.

System Param << Island OFF

Run Param Meter 0FF <<
Pic �.�� Parameter setting Pic �.�� Meter switch

�. Operate the button [up down], move setting cursor to energy meter and press the button
[enter]. At this time you can turn on or turn off the energy meter by choosing [up down]
button, please press [enter] button to confirm when setting done.
�. Move the cursor to [OK], press [enter] to save the settings and exit the running parameters
page, otherwise the settings are invalid.
�. If set up successfully, you can return to the menu interface, and display the LCD to [home
page] by press the [up down] button. If it displays [meter power XXW], the zero-export
function setting is completed. Shown as picture �.��.

Meter Power:
20W
Pic �.�� Zero-export function via energy meter turn on
�. Meter power XXW shows positive means grid is supplying the load, and no power fed into
grid. if meter power shows negative, it means PV energy is being sold to grid or energy meter
wiring conncetion has problem.
�. After properly connection is done, wait for inverter starting. If the power of the PV array
meets the current power consumption, the inverter will keep a certain output to counteract
the power of the grid without backflow .

- �� -
�.� Notes while using zero export function

For your safety and the operation of limiter function of the inverter, we put forward the follow-
ing suggestions and precautions:

Safety Hint:
Under zero export mode we strongly recommend that the two PV arrays are formed by the same
number of PV panels of the same size, which will make the inverter more responsive to limit the
power.

Safety Hint:
While the utility power is negative and inverter has no output power, that means the orientation of
the current sensor is wrong, please turn off the inverter and change orientation of the current sensor.

�.� How to browse the load power of your PV grid-tie plant on monitoring platform?
If you want to browse load power of the system and how much energy (KWH) does it export to
grid(inverter output power is used to power the load firstly and then the surplus energy will feed
into grid). You also need to connect the meter according to above diagram. After the connection
completed successfully, the inverter will show the load power on the LCD. But please don’t
setup “Meter ON”. Also, you will be able to browse the load power on the monitoring platform.
The plant setting method as below description.
Firstly, go to the solarman platform(https://pro.solarmanpv.com, this link is for solarman
distributor account; or https://home.solarmanpv.com, this link is for solarman end user
account;) plant home page and click “edit”.
Back to Plants list String inverter Solar Station ID13199 Compare Add Edit More

String inverter Solar Sta...

！ Partially Offline No Alerts Last update 2021/03/22 08:40:59 UTC+08:00
Edit Tags
Dashboard

Devices Cover Updated: 2021/03/22 08:35:33

Flow Graph Production Consumption Grid

Alerts 10℃
Production Power 9.52 kW Grid Power 5℃/13℃ Sunny MON
About
6.87 kW 4 m/s 05:55 18:05
32% Capacity 30 kWp

Authorizations
16℃ 13℃ 17℃ 18℃

Layout

Work Order Address YongJiang Road,Beilun,Ning...

Plant Type Residential

5℃ 9℃ 9℃ 10℃
Plan

System Type Self-consumption Consumption Power

Maintenance
Record 2.6kW TUE WED THU FRI
Phone
3/23 3/24 3/25 3/26

- �� -
And then choose your system type as “Self-consumption”

Edit Plant Cancel Done

* Address :
Basic Info
YongJiang Road, Beilum,NingBo, 315806, China
System Info
Yield Info * Coordinates :
Owner Info Longitude 121 46 19.03 ” Latitude 29 53 36.11
‘ ‘
”

Time Zone : Creation Time :

2020/04/08
(UTC+08:00) Beijing,Chongqing,Hong Kong,Urumqi

System Info Collapse

Plant Type : System Type :

Residential Self-consumption

* Capacity(kWp): Azimuth( ):

30 0~360

Secondly, go to plant page, if it shows the PV power, load power and grid power, which means
the configuration is correct.
Back to Plants list String inverter Solar Station ID13199 Compare Add Edit More

String inverter Solar Sta...

！ Partially Offline No Alerts Last update 2021/03/22 08:40:59 UTC+08:00
Edit Tags
Dashboard

Devices Cover Updated: 2021/03/22 08:35:33

Flow Graph Production Consumption Grid

Alerts 10℃
Production Power 9.52 kW Grid Power 5℃/13℃ Sunny MON
About
6.87 kW 4 m/s 05:55 18:05
32% Capacity 30 kWp

Authorizations
16℃ 13℃ 17℃ 18℃

Layout

Work Order Address YongJiang Road,Beilun,Ning...

Plant Type Residential

5℃ 9℃ 9℃ 10℃
Plan

System Type Self-consumption Consumption Power

Maintenance
Record 2.6kW TUE WED THU FRI
Phone
3/23 3/24 3/25 3/26

Flow Graph Production Consumption Grid

Production Power 9.52 kW Grid Power

32% Capacity 30 kWp 6.87 kW

Consumption Power
2.6kW

- �� -
8. General Opera�on
During normal operation, the LCD shows the current status of the inverter, including the current
power, total generation, a bar chart of power operation and inverter ID,etc. Press the Up key
and the Down key to see the current DC voltage, DC current, AC voltage, AC current,inverter
radiator temperature,software version number and Wifi connection state of the inverter.

LCD Main menu

GL3000 SN-01
Total DC Power PF:0.000
Device ID:2104149060
PV1 and Power informa�on Inv1400
LcdA244
UA and UB 1 F35 220513 07
2 F35 220513 06
UC and Freq Fault record 3 F35 220513 06
4 F35 220513 06
E-Day and E-Total
Start Time ON/OFF
Turn ON

Turn OFF
*Meter

*IoaEp and Total Setup

*lmpEp and Total Branch 1 : 0.0A

*PV VA
*Load Branch 2 : 0.0A

*ExpEp and Total

Time Set
English
Polski
Language Set P cck
Nederland
Bright Delay
Setup System param Display Set Delay �me 05S
OK << Cancel
Confirm Reset
Factory Reset
Cancel
I Confirm
Set Restore
Cancel

- �� -
 P1-P6
QP Vstart
Q1-Q6
Vstop
PFP
Pstart P1-P6 PF1-PF6
Pstop RmpTime
Ac�veP QU
PmpTime
Q-Mode PtUsed
PF
VRated V1-V6 Q1-Q6
Q(%)
ReactP

PF OFF
AVG
Fun- ISO Exp_Mode
MIN EXT_01
CT_Ra�o 0 ACREL
Fun RCD MFR EASTRON
FeedIn OFF CHNT
SelfCheck Shunt MST AUTO
ShuntQTY SLV
Island
Generator
Meter G.CT AUTO
EASTRON
Setup Limiter
G.MFR
G.FeedIn
ACREL
CHNT
Running param Feed-in G.Pout
G.Cap V1-V12
MPPT Num DC1-Wind OFF/ON
DC2-Wind OFF/ON
WindTurbine OK
CLR
Cancel
ARC ON
OFF
OF-Derate HYS
ON
UF-Uprate OFF
WGRa

WGraStr
ON
PU OFF
V1-V4 P1-P4
LVRT

HVRT

DRM
Sunspec

ZVRT

- �� -
 Brazil
*Note: These parameters will be avaiable after the meter is EN50549-1-PL
connected successfully. Otherwise, it won't show. EN50549-1
IEC61727
CUSTOM
VDE_4105
VDE_0126
Spain
CEI_0-21
G98_G99
NB/T 32004-B
Australia-A-C
NEW Zealand
E MEA
PEA
Norway
Switzerland
GridStanderd R25
Protect Param Advanced OverVolt Lv3-Lv1
Point 240.0V
Back Delay 1000ms
UnderVolt Lv1-Lv3
Point 235.0V
Delay 1000ms
Setup OverFreq Lv3-Lv1
Point 52.00Hz
Delay 1000ms
UnderFreq Lv1-Lv3
Point 48.00Hz
Delay 1000ms
Reconnec�on
Vup
Vdown
Fup
Fdown
OV 10 Minutes
Enable
Point
Grid: 127/220V

Address:01
Comm. param Meter:AUTO
BaudRate: 9600

Pic 8.1 LCD opera�on flow chart

- �� -
�.� The initial interface

From the initial interface, you can check PV power, PV voltage, grid voltage, inverter ID, model
and other infomation.

Power: 0W Power: 0W
State: Standby State: Com.Error
Pic �.� The initial interface

Press UP or Down, you can check inverter DC voltage, DC current, AC voltage, AC current and
inverter temperature.

Total DC POWER: PV1: 0.0V 0.0A

0W Power: 0W
Pic �.� PV input voltage and current Pic �.� Load power
information

UA: 234V 0.0A UC: 0V 0.0A

UB: 0V 0.0A Freq: 0.00Hz
Pic �.� Grid voltage and current information Pic �.� Grid voltage and frequency

E-Day: Daily generation;

E-Day : 0Wh E-Total: Total generation.

E-Total : 134KWh
Pic �.� PV generation

21 - 05 - 2020 Meter
15 : 57 : 08 Power: 0W
Pic �.� Time Pic �.� Meter power

LoadEp: Daily consumption;

LoadEp: 0.00KWh Total: Total energy consumption.

Total : 0.00KWh
Pic �.�� Load consumption

- �� -
 ImpEp: Daily energy purchased from grid;
ImpEp: 0.00KWh Total: Total energy purchased from grid.

Total : 0.00KWh
Pic �.�� Electrical energy
ExpEp: Daily energy sold to grid;
ExpEp: 0.00KWh Total: Total energy sold to grid.

Total : 0.00KWh
Pic �.�� Electrical energy

�.� Submenus in the Main Menu

There are five submenus in the Main Menu.

�.�.� Device information

You can see the LCD software VerA��� and control board software Ver����. In this interface,
there are parameters such as rated power communication addresses.

Device Info. << GL3000 SN-01

Fault Record PF: 0.000

ID:2104149060 Inv1400
Inv1400 LcdA244
Pic �.�� Device information

�.�.� Fault Record

It can keep Eight fault records in the menu including time, customer can deal with it depends
on the error code.

Device Info. 1 F35 220513 07

Fault Record << 2 F35 220513 06
3 F35 220513 06
4 F35 220513 06
Pic �.�� Fault Record

- �� -
�.�.� ON/OFF setting

ON / OFF << Turn ON <<

Setup Turn OFF
Turn ON Turn OFF
OK << Cancel OK << Cancel
Pic �.�� ON/OFF setting

When the inverter is turned off, it stops working immediately, and go to standby mode and
then will go to self-test program again. If it passed the self-test, it will start to work again.

�.�.� Parameter setting

There are five submenus in the setup.Setting includes system param, run param, protect
param, comm: param. All of these information for maintenance reference.

System Param << Protect Param

Run Param Comm. Param <<
Pic �.�� Submenus of the parameter setup

- �� -
�.� System param setting

System Param includes time set, language set, display set and factory reset.

Time Set << Display Set

Language Set Factory Reset <<
Factory Reset
Set Restore <<
Pic �.�� System Param

20200522 OK English <<

08:11:21 Cancel Polski
Pic �.�� Time

English Bright Delay <<

Nederland << Delay time 05S
Pic �.�� Language Pic �.�� LCD Screen settings

Delay time 05S Factory Reset <<

OK << Cancel Cancel
Pic �.�� Delay time set Pic �.�� Reset to factory setting

I Confirm <<
Cancel
Pic �.�� Set Restore

- �� -
�.� Running param set

Warning:
Password required-- only for access-authorized engineer. Un-authorized access
may avoid the warranty. The initial password is ����.

PassWord

Pic �.�� Password

ActiveP 0% Vref 0.0V

Q-Mode OFF << ReactP 0.0% <<
PF -1.000 Fun -RCD OFF <<
FunISO
- OFF << SelfCheck 0S
Island OFF << Limiter OFF
Meter OFF Feed-in 0% <<
MPPT Num 0 ARC ON
WindTurbine << OF-Derate OFF <-
UF-Uprate OFF <- WGra 0.0% <<
WGra 0.000% WGraStr 0.0%
PU ON LVRT OFF
PowerLim << HVRT OFF <<
DRM OFF Sunspec OFF <<
Sunspec OFF << ZVRT <<

- �� -
OK Cancel <<

Pic �.��

Name Description Range

ActiveP Adjust the output active power in % �-���%

OFF/Q(P)/PF(P)
Q-Mode Multiple reactive power control modes
/Q(U)/PF/Q(%)

Grid reference voltage for functions

Vref including Q(U),PF(P),P(U)etc. ��-���V

ReactP Adjust reactive power output in % -���%-+���%

PF Power Fator -�-�.�~+�.�-�

Fun_ISO Insulation resistance detection ON/OFF

Fun_RCD Residual current detection ON/OFF

Inverter's self-check time.The default

Self-check value ��s �-����s

Island Anti-islanding protection ON/OFF

If you want to use zero output mode,please set

Meter Meter to ON and select OFF to view data only ON/OFF

It is used to deploy how much power can be

feed in to grid when the inverter works under
zero export mode.(For example,Feed_in=��%
Feed_IN % of the ��KW model and load power is �KW. �-���%
which means Max �KW power can be feed into
grid after inverter providing �Kw to the load
firstly.

Pic �.��

- �� -
Name Descrip�on Range

ARC Arc-fault detection function ON/OFF/CLR

Active power response to over-

OF-Derate frequency
ON/OFF/HYS

Active power response to under-

UF-Uprate frequency
ON/OFF

power response to grid voltage

PU deviation
ON/OFF

LVRT voltage ride through function ON/OFF

HVRT voltage ride through function ON/OFF

PowerLim Hard/soft export limit control ON/OFF

DRM Demand Response Modes ON/OFF

Sunspec Sunspec Function ON/OFF

Percentage of Nominal Power

WGraStr per second
�.�%~��%

percentage of Nominal Power

WGra per second
�.�%~��%

ZVRT Zero Current Mode ON/OFF

Pic �.��

ISO SEN MIN<< ISO SEN HIG<<

Back Back
ISO SEN MID<<
Back
Pic �.�� FUN_ISO

- �� -
RCD SEN MIN << ARC SEN HIG <<
Back Back
ARC SEN MID <<
Back
Pic �.�� FUN_RCD

Island SEN MIN << Island SEN HIG <<

Back Back
Island SEN MID <<
Back
Pic �.�� Island

ARC SEN HIG << ARC SEN MID <<

Back Back
ARC SEN MIN <<
Back
Pic �.�� ARC

- �� -
Over-frequency Response
This series inverter provides “over-frequency response” function.
Long pressing the “OFD Mode” to enter the “over-frequency response”
setting menu.

ARC ON ARC ON
OF-Derate ON <- OFDMode HYS <-
ARC ON
OF-Derate OFF <-
Tab. �-� Definition of Over-frequency Response Parameters

Parameter Range Description

Fstr ��HZ-��HZ The Start frequency value for over-frequency response.
Fstop ��HZ-��HZ The Stop frequency value for over-frequency response.
RecGra [�,���] �.��%Pmax/s Rate of Power recovery(Percentage of active power)

For example, StrtPT: ��.�Hz, StopPT:

��.�Hz, RecPT: ��.�Hz, when the grid
frequency increases beyond Start: ��.�Hz, Fstr 50.50Hz
the inverter will linearly reduce the power
output with a gradient of ���% Pmax/Hz
until it reaches StopPT: ��.�Hz.
Fstop 51.50Hz <<

Rated
Output RecPT
Power(kW) Fstr

Hysteresis mode Fstop

��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.� ��.�
Grid Frequency(Hz)

Fig. �-� Frq-Watt Mode for Over-frequency Conditions

- �� -
HardLimitation HardLimitation
Enable OFF << Point 0.0% <<
SoftLimitation SoftLimitation
Enable OFF << Point 0.0% <<
PTD_H 0.0S OK << Cancel
M_OFF 0.0%<<
Pic �.�� PowerLim

Vstart 0.0% OK Cancel <<

Vsop 0.0% <<
Pic �.�� LVRT

- �� -
When the frequency exceeds Fstop: ��.�Hz, the inverter output should stop (ie � W).
When the frequency is lower than Fstop: ��.� Hz, the inverter will linearly increase the power
output with a gradient of ���% Pmax/Hz until it reaches Fstr: ��.� Hz.
In the hysteresis mode, when the frequency is lower than Fstop: ��.� Hz, the inverter will not
increase the power output until it is lower than RecPT: ��.� Hz.

Frec 50.10Hz RecDly 0s

RecGra 0.00% << RsponDy 0s <<
OK << Cancel

The inverter provides a reactive power regulation function.

Tap Reactive Power Regulation Mode to select proper regulation mode and set the correspond-
ing parameters.
Pic �.�� OF-Derate

ActiveP 0% ActiveP 0%
Q-Mode OFF << Q-Mode QU+QP <<
ActiveP 0% ActiveP 0%
Q-Mode Q(P) << Q-Mode PF(P) <<
ActiveP 0% ActiveP 0%
Q-Mode Q(U) << Q-Mode PF <<
ActiveP 0%
Q-Mode Q(%) <<
Pic �.��

- �� -
 "OFF" Mode
The reactive power regulation function is disabled. The PF is fixed at +1.000

Q(%)
Adjust reactive power output in %.

"PF" Mode
The power factor (PF) is fixed and the reactive power is regulated by the parameter PF. The PF
ranges from 0.8 leading to 0.8 lagging.
•Leading: the inverter is absorbing reactive power from the Grid.
•Lagging: the inverter is injecting reactive power into the grid.

"Q(U)" Mode
The reactive power output of the inverter varies in response to the grid voltage.
"Q(P)" Mode
The reactive power output by the inverter is controlled by the active power of the inverter.

"PF(P)" Mode
The PF is controlled by the active power of the inverter.

“PU” Mode

The active power output of the inverter varies in response to the grid voltage.

WGraStr 0.0% WGraStr 0.0%

PU OFF <- PU ON <-
V1 0.0% << V2 0.0% <<
P1 0.0% P2 0.0%
V3 0.0% << V4 0.0% <<
P3 0.0% P4 0.0%
Ti 0s
OK Cancel <<

- �� -
 U/Vref

(U1,P1)

(U2,P2)

(U3,P3)

(U4,P4)

P/Pn

Pic �.�� Active Power Regulation Curve in PU Curve

Parameter Range Descrption

Value of P/Pn at point (P�,U�) on the PU mode
P� �%-���% Pn curve
Grid voltage limit at point (P�,U�) on the PU mode
U� �% -���% Vref curve
Value of P/Pn at point (P�,U�) on the PU mode
P� �%-���% Pn
curve
Grid voltage limit at point (P�,U�) on the PU mode
U� �% -���% Vref curve
Value of P/Pn at point (P�,U�) on the PU mode
P� �%-���% Pn
curve
Grid voltage limit at point (P�,U�) on the PU mode
U� �% -���% Vref curve
Value of P/Pn at point (P�,U�) on the PU mode
P� �%-���% Pn
curve
Grid voltage limit at point (P�,U�) on the PU mode
U� �% -���% Vref
curve
The adjustment time of PU Curve in seconds (time
Ti �-����s
to accomplish a change of ��%).

"PU" Mode Parameters Explanation

- �� -
“Q(U)” Mode

ActiveP 0% Pstart 0.0% <<

QMode Q(U) <- Pstop 20.0%
RmpTime 0s UrefAuto 0s
RmpUref 0 << PtUsed 0 <<
V1 0.0% << V2 0.0% <<
Q1 0.0% Q2 0.0%
V3 0.0% << V4 0.0% <<
Q3 0.0% V4 0.0%
V5 0.0% << V6 130.0% <<
Q5 0.0% Q6 30.0%
Q6 0.0%
OK Cancel <<
Pic �.��

- �� -
 (U�,Q�)
Upper
Q/Pn lnd

(U�,Q�)

(U�,Q�)
Grid
Voltage
(U�,Q�)

(U�,Q�)

Lower
Q/Pn Cap (U�,Q�)

Pic �.�� Reactive Power Regulation Curve in Q(U) Curve

- �� -
Parameter Range Description
The QU mode starts when the active power
Pstart �%-���% Rate out power is greater than this value

The QU mode stops when the active power

Pstop �%-���% Rate out power
is less than this value

Value of Q/Pn at point (U1,Q1) on the Q(U)

Q� -��% -��% Q/Pn mode curve
Grid voltage limit at point (U1,Q1) on the
V� �-���% VRated Q(U) mode curve

Value of Q/Pn at point (U2,Q2) on the Q(U)

Q� -��% -��% Q/Pn mode curve

�-���% VRated Grid voltage limit at point (U2,Q2) on the

V�
Q(U) mode curve

Q� Value of Q/Pn at point (U3,Q3) on the Q(U)

-��% -��% Q/Pn
mode curve
Grid voltage limit at point (U3,Q3) on the
V� �-���% VRated Q(U) mode curve

Q� Value of Q/Pn at point (U4,Q4) on the Q(U)

-��% -��% Q/Pn mode curve

Grid voltage limit at point (U4,Q4) on the

V� �-���% VRated
Q(U) mode curve

Q� Value of Q/Pn at point (U5,Q5) on the Q(U)

-��% -��% Q/Pn mode curve
Grid voltage limit at point (U5,Q5) on the
V� �-���% VRated Q(U) mode curve

Value of Q/Pn at point (U6,Q6) on the Q(U)

Q� -��% -��% Q/Pn mode curve

Grid voltage limit at point (U6,Q6) on the

V� �-���% VRated Q(U) mode curve

Increase or decrease the time required for

RMpTime �-����s the reactive power to reach the specified
value of the curve.

"Q(U)" Mode Parameters Explanation

- �� -
“Q(P)” Mode

The reactive power output by the inverter is controlled by the active power of the inverter.
Upper
Q/Pn lnd
(P1,Q1)

P2(P2,Q2)

P4(P4,Q4) P/Pn

P3(P3,Q3)

P5(P5,Q5)

Lower
P6(P6,Q6)
Q/Pn Cap
Pic �.�� Reactive Power Regulation Curve in Q(P) Mode

ActiveP 20.0% P1 0.0% <<

QMode QP <- Q1 0.0%
P2 0.0% << P3 0.0% <<
Q2 0.0% Q3 0.0%
P4 0.0% << P5 0.0% <<
Q4 0.0% Q5 0.0%
P6 0.0% << OK << Cancel
Q6 0.0%

- �� -
Parameter Range Description
Power value/Pn at point (P1,Q1) on the Q(P) mode
P1 0%-100% Pn
curve
Reac�ve power value at point (P1,Q1) on the Q(P)
Q1 -60% -60% Q/Pn
mode curve
Power value/Pn at point (P2,Q2) on the Q(P) mode
P2 0%-100% Pn
curve
Reac�ve power value at point (P2,Q2) on the Q(P)
Q2 -60% -60% Q/Pn
mode curve
Power value/Pn at point (P3,Q3) on the Q(P) mode
P3 0%-100% Pn
curve
Reac�ve power value at point (P3,Q3) on the Q(P)
Q3 -60% -60% Q/Pn
mode curve
Power value/Pn at point (P4,Q4) on the Q(P) mode
P4 0%-100% Pn
curve
Reac�ve power value at point (P4,Q4) on the Q(P)
Q4 -60% -60% Q/Pn
mode curve
Power value/Pn at point (P5,Q5) on the Q(P) mode
P5 0%-100% Pn
curve
Reac�ve power value at point (P5,Q5) on the Q(P)
Q5 -60% -60% Q/Pn
mode curve
Power value/Pn at point (P6,Q6) on the Q(P) mode
P6 0%-100% Pn
curve
Reac�ve power value at point (P6,Q6) on the Q(P)
Q6 -60% -60% Q/Pn
mode curve

"Q(P)" Mode Parameters Explanation

- �� -
"PF(P)" Mode

The output power factor is controlled by the active power of the inverter.

Vstart 0.0% P1 0.0%

Vstop 0.0% PF1 -1.000 <<
P2 0.0% P3 0.0%
PF2 -1.000 << PF3 -1.000 <<
P4 0.0% P5 0.0%
PF4 -1.000 << PF5 -1.000 <<
P6 0.0% RmpTime 0s
PF6 -1.000 << OK Cancel <<
PF lagging
P�(P�,PF�)

P�(P�,PF�)

P4(P4,PF4)
P/Pn
P�(P�,PF�)

P5(P5,PF5)

PF leading
P6(P6,PF6)

Pic �.�� Power factor Regulation Curve in PF(P) Mode

- �� -
Parameter Range Description
The PFP mode is enable when grid
Vstart �-���% Vref
voltage is greater than Vstart
The PFP mode is disable when grid voltage
Vstop �-���% Vref
is less than Vstop
Power value at point (PF�,P�) on the PF(P)
P� �-���% Pn
Curve
PF value at point (PF�,P�) on the PF(P)
PF� �.� leading - �.� lagging
Curve
Power value at point (PF�,P�) on the PF(P)
P� �-���% Pn
Curve
PF value at point (P�,PF�) on the PF(P)
PF� �.� leading - �.� lagging
Curve
Power value at point (P�,PF�) on the PF(P)
P� �-���% Pn
Curve
PF value at point (P�,PF�) on the PF(P)
PF� �.� leading - �.� lagging
Curve
Power value at point (P�,PF�) on the PF(P)
P� �-���% Pn
Curve
PF value at point (P�,PF�) on the PF(P)
PF� �.� leading - �.� lagging
Curve
Power value at point (P�,PF�) on the PF(P)
P� �-���% Pn
Curve

PF� �.� leading - �.� lagging

PF value at point (P5,PF5) on the PF(P)
Curve
Power value at point (P�,PF�) on the PF(P)
P� �-���% Pn
Curve
PF value at point (P�,PF�) on the PF(P)
PF� �.� leading - �.� lagging
Curve

The time of the PFF Curve in seconds

RMpTime �-����s
(time to accomplish a change of ��%).

"PF(P)" Mode Parameters Explanation

- �� -
�.� Protect Param

Warning:
Engineer Only.
We will set the param depends on the safety requirements, so customers don't
need to reset it. The password is same as �.� Running param

PassWord GridStanderd <<

Advanced

Back <<

Pic �.�� Password

Braszil EN50549-1
EN50549-1-PL << IEC61727 <<
CUSTOM VDE0126
VDE4105 << Spain <<
_
CEI_0-21 G99
G98 << NBT32004-B <<
Australia-A Australia-C
Australia-B << New Zealand <<
MEA Norway
PEA << Switzerland <<
R25
OK Cancel <<
Pic �.�� GridStanderd

- �� -
OverVolt Lv3 OverVolt Lv3
Point 240.0V << Delay 1000ms <<
OverVolt Lv2 OverVolt Lv2
Point 240.0V << Delay 1000ms <<
OverVolt Lv1 OverVolt Lv1
Point 240.0V << Delay 1000ms <<
UnderVolt Lv1 UnderVolt Lv1
Point 235.0V << Delay 1000ms <<
UnderVolt Lv2 UnderVolt Lv2
Point 235.0V << Delay 1000ms <<
UnderVolt Lv3 UnderVolt Lv3
Point 235.0V << Delay 1000ms <<
OverFreq Lv3 OverFreq Lv3
Point 52.00Hz << Delay 1000ms <<
OverFreq Lv2 OverFreq Lv2
Point 52.00Hz << Delay 1000ms <<
OverFreq Lv1 OverFreq Lv1
Point 52.00Hz << Delay 1000ms <<
UnderFreq Lv1 UnderFreq Lv1
Point 48.00Hz << Delay 1000ms <<
- �� -
 UnderFreq Lv2 UnderFreq Lv2
Point 48.00Hz << Delay 1000ms <<
UnderFreq Lv3 UnderFreq Lv3
Point 48.00Hz << Delay 1000ms <<
Reconnection Reconnection
Vup 0.0V << Vdown 0.0V <<
Reconnection Reconnection
Fup 0.00Hz << Fdown 0.00Hz <<
OV 10 Minutes OV 10 Minutes
Enable OFF << Point 0.0% <<
Point 0.0% OK Cancel <<
Grid --- <<
Pic �.�� “CUSTOMIZED”

Please set the proper grid parameters according to the requirements of your current country's
grid regulations.If you are not clear about it, please consult your installer.

�.� Comm. param set

Address: 01 << Func: Meter

BaudRate: 9600 Address1: 01 <<
Pic �.�� Comm. Param

- �� -
9. Repair and Maintenance
String type inverter doesn’t need regular maintenance. However,debris or dust will affect
heat sink’s thermal performance. It is better to clean it with a soft brush. If the surface is too
dirty and affect the reading of LCD and LED lamp, you can use wet cloth to clean it up.

High Temperature Hazard:

When the device is running, the local temperature is too high and the touch can
cause burns. Turn off the inverter and wait for it cooling, then you can clean and
maintain.
Safety Hint:
No solvent, abrasive materials or corrosive materials can be used for cleaning
any parts of the inverter.

10.Error informa�on and processing

Inverter has been designed in accordance with international grid tied standards for safety, and
electromagnetic compatibility requirements. Before delivering to the customer the inverter
has been subjected to several tests to ensure its optimal operation and reliability.

- �� -
��.� Error code
If there is any failure,the LCD screen will display an alarm message. In this case,the inverter
may stop feeding energy into the grid. The alarm description and their corresponding alarm
messages are listed Table ��.�.

Error code Description Ongrid - Three Phase

F01 DC input polarity reverse fault Check the PV input polarity.

DC insulation impedance
F02 Check the grounding cable of inverter.
permanent fault

F03 DC leakage current fault Hardly appear the code. Never ever happened so far.

F04 Ground fault GFDI Check the solar panel output connection.

Failure in reading memory (EEPROM). Restart the inverter if the

F05 Read the memory error
fault still exists, contact your installer or Deye service.

Failure in writing memory (EEPROM). Restart the inverter if the

F06 Write the memory error
fault still exists, contact your installer or Deye service.

F07 GFDI blown fuse Hardly appear the code. Never ever happened so far.

F08 GFDI grounding touch failure Hardly appear the code. Never ever happened so far.

IGBT damaged by excessive drop

F09 Hardly appear the code. Never ever happened so far.
voltage

1. It tells the DC 12V is not existed.

Auxiliary switch power supply
F10 2. Restart the inverter, if the fault still exists, please contact
failure
your installer or Deye service.

F11 AC main contactor errors Hardly appear the code. Never ever happened so far.

F12 AC auxiliary contactor errors Hardly appear the code. Never ever happened so far.

1. Loss of one phase or AC voltage detection part failure or

relays not closed.
F13 reserved
2. Restart the inverter, if the error still exists, please contact your
installer or Deye service.

F14 DC firmware over current Hardly appear the code. Never ever happened so far.

1. The internal AC sensor or detection circuit on control board

or connection wire may loose.
F15 AC firmware over current 2. Restart the inverter, if the error still exists, please contact
your installer or Deye service.

1. This fault means the average leakage current is over 300mA.

Check whether DC power supply or solar panels is ok, then
check 'Test data'-> 'diL'value is about 40; Then check the
GFCI(RCD) Ac leakage current
F16 leakage current sensor or circuit (the following picture).
fault
Checking test data needs using big LCD.
2. Restart the inverter, if the error still exists, please contact your
installer or Deye service.

Three phase current,

F17 Hardly appear the code. Never ever happened so far.
over-current fault

1. Check AC sensor or detection circuit on control board or

connection wire.
F18 AC over current fault of hardware 2. Restart the inverter or factory reset, if the error still exists,
please contact your installer or Deye service.

F19 All hardware failure synthesis Hardly appear the code. Never ever happened so far.

- �� -
Error code Description Ongrid - Three Phase
1. Check whether solar panel output current is within the
allowed range.
DC over current fault of the 2. Check DC current sensor and its detection circuit.
F20
hardware 3. Check if the inverter FW version is suitable for the hardware.
4. Restart the inverter, if the error still exists, please contact your
installer or Deye service.

F21 DC leakage flow fault Hardly appear the code. Never ever happened so far.

Crash stop (if there is a stop

F22 Contact your installer for help.
button)

1. This fault means the leakage current is above 30mA suddenly.

Check whether DC power supply or solar panels is ok, then
AC leakage current is transient check 'Test data'-> 'diL'value is about 40; Then check the
F23 leakage current sensor or circuit. Check test data needs
over current
using big LCD.
2. Restart the inverter, if the fault still exists, contact your installer
or Deye service.
1. Check Vpe resistance on main board or detection on control board.
Check PV panels is OK. Many times this issue is the PV problem.
2. Check whether the PV panel (aluminum frame) is grounded well and
inverter is grounded well. Open the cover of inverter and then check
F24 DC insulation impedance failure the inside ground cable is fixed well on the shell.
3. Check if the AC/DC cable, terminal block are shorted to ground or
the insulation is damaged.
4. Restart the inverter, if the fault still exists, contact your installer or
Deye service.

F25 DC feedback fault Hardly appear the code. Never ever happened so far.

1. Check whether the 'BUSN' cable or driver board power supply

F26 The DC busbar is unbalanced cable is loose.
2. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

F27 DC end insulation error Hardly appear the code. Never ever happened so far.

F28 Inverter 1 DC high fault Hardly appear the code. Never ever happened so far.

F29 AC load switch failure Hardly appear the code. Never ever happened so far.

1. Check relays and AC voltage of relays.

2. Check relays driver circuit. Check if the software is not suitable
F30 AC main contactor failure for this inverter. (Old inverter not have relays detection
function)
3. Restart the inverter, if the fault still exists, contact your
installer or Deye service.
1. At least one Relay can't be closed. Check relays and its driver
F31 Relay open circuit fault signal. (Old inverter not have relays detection function)
2. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

F32 Inverter 2 dc high fault Hardly appear the code. Never ever happened so far.

F33 AC over current Hardly appear the code. Never ever happened so far.

F34 AC current over load Hardly appear the code. Never ever happened so far.

1. Check AC grid voltage. Check AC voltage detection circuit.

Check if the AC connector in good condition. Check whether
F35 No AC grid the AC grid is normal in voltage.
2. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

- �� -
Error code Description Ongrid - Three Phase

F36 AC grid phase error Hardly appear the code. Never ever happened so far.

AC three-phase voltage unbalance

F37 Hardly appear the code. Never ever happened so far.
failure

AC three-phase current unbalance

F38 Hardly appear the code. Never ever happened so far.
failure

1. Check AC current sensor and its circuit.

F39 AC over current(one cycle) 2. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

F40 DC over current Hardly appear the code. Never ever happened so far.

Check the AC voltage protection setting. And Check if the AC

F41 AC Line W,U over voltage cable is too thin.Check the voltage difference between LCD and
meter.

Check the AC voltage protec�on se�ng. Check the voltage

F42 AC Line W,U low voltage difference between LCD and meter. Also need to check whether
AC cables are all firmly and correctly connected.

Check the AC voltage protection setting.And Check if the AC

F43 AC Line V,W over voltage cable is too thin.Check the voltage difference between LCD and
meter.

Check the AC voltage protection setting. Check the voltage

F44 AC Line V,W low voltage difference between LCD and meter. Also need to check whether
AC cables are all firmly and correctly connected.

Check the AC voltage protection setting.And Check if the AC

F45 AC Line U,V over voltage cable is too thin.Check the voltage difference between LCD and
meter.

F46 AC Line U,V low voltage Check the AC voltage protection setting.

F47 AC Over frequency Check the frequency protection setting.

F48 AC lower frequency Check the frequency protection setting.

U phase grid current DC

F49 Hardly appear the code. Never ever happened so far.
component over current

V phase grid current DC

F50 Hardly appear the code. Never ever happened so far.
component over current

W phase grid current DC

F51 Hardly appear the code. Never ever happened so far.
component over current

AC inductor A, phase current

F52 Hardly appear the code. Never ever happened so far.
DC current high

AC inductor B, phase current

F53 Hardly appear the code. Never ever happened so far.
DC current high

AC inductor C, phase current

F54 Hardly appear the code. Never ever happened so far.
DC current high

1. Check PV voltage and Ubus voltage and its detection circuit.

F55 DC busbar voltage is too high If the PV input voltage exceeds the limit, please reduce the
number of solar panels in series.
2. For Ubus voltage, please check the LCD display.

- �� -
 Error code Description Ongrid - Three Phase

1. It tells the PV input voltage is low and it always happens in the

early morning.
2. Check PV voltage and Ubus voltage. When inverter is running,
F56 DC busbar voltage is too low then showing F56, maybe Loss of driver or need update
firmware.
3. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

F57 AC reverse irrigation AC reverse irrigation.

F58 AC grid U over current Hardly appear the code. Never ever happened so far.

F59 AC grid V over current Hardly appear the code. Never ever happened so far.

F60 AC grid W over current Hardly appear the code. Never ever happened so far.

F61 Reactor A phase over current Hardly appear the code. Never ever happened so far.

F62 Reactor B phase over current Hardly appear the code. Never ever happened so far.

1. Check PV module cable connection and clear the fault;

ARC fault 2. Seek help from us, if can not go back to normal state.
F63
1. Check temperature sensor. Check if firmware is suitable for
F64 IGBT heat sink high temperature the hardware. Check if the inverter is its right model.
2. Restart the inverter, if the fault still exists, contact your
installer or Deye service.

Table��.� Error codes and their solutions

Safety Hint:
If your string inverter has any of the fault information shown in Table ��-�,and
when you reset the machine and still don’t solve the problem,please contact
our distributor and provide the below details:

�. Serial number of the inverter;

�. The distributor/dealer of the inverter(if available);
�. Installation date;
�. The discription of problem(include LCD'error code and LED starus indicator lights);
�. Your contact details.

- �� -
11.Specifica�on
SUN-�K- SUN-�K- SUN-�K- SUN-�K-
Model G�� G�� G�� G��
Input Side
Max.DC Power(kW) �.�kW �.�kW �.�kW �.�kW
Max.DC Input Voltage(V) ����V
Start-up DC Input Voltage(V) ���V
MPPT Operating Range(V) ���V~���V
Rated DC input voltage(V) ���V
MPPT Full Power Voltage Range(V) ���V~���V
Max.DC Input Current(A) ��A+��A
Max. Short Circuit Current (A) ��.�A+��.�A
Number of MPPT/Strings per MPPT �/�+�
MAX inverter backfeed current (A) �A
Output Side
Rated Output Power(kW) �kW �kW �kW �kW
Max.Active Power(kW) �.�kW �.�kW �.�kW �.�kW
Rated AC Grid Voltage(V) �L/N/PE ���/���V ���/���V
AC Grid Voltage Range(V) �.��Un-�.�Un (this may vary with grid standards)
Rated Grid Frequency(Hz) ��/�� (Optional)
Operating Phase Three phase
Rated AC Grid Output Current(A) �.�/�.�A �.�/�.�A �.�/�.�A �.�/�.�A
Max.AC Output Current(A) �/�.�A �.�/�.�A �.�/�A ��/�.�A
Maximum output fault �.�A ��.�A ��.�A ��.�A
current (a.c. A, peak )
Maximum output overcurrent �.��A ��.�A ��.�A ��.�A
protection (a.c. A,peak)
Output Power Factor �.� leading~�.� lagging
Grid Current THD <�%
DC Injection Current <�.�%
Grid Frequency Range ��-�� or ��-�� (Optional)
Efficiency
Max.Efficiency ��.�% ��.�%
Euro Efficiency ��.�%
MPPT Efficiency >��%
Surge Protection DC Type II / AC Type II
General Data
Cabinet Size(W*H*D) [mm] ��������� (Excluding connectors and brackets)
Weight(kg) ��
Topology Transformerless
Internal consumption <�W (Night)
Operating temperature -�� ~ ��℃,>��℃ derating
Ingress protection IP��
Noise Emission(Typical) ＜�� dB
Type Of Cooling Free cooling
Permissible Altitude (m) ����m
Warranty [year] Standard � years, extended warranty
VDE����, IEC�����/�����, VDE����, AS����.�, CEI � ��,
Grid Connection Standard
EN�����-�, G��, G��, C��-��, UNE������, NBR�����/NBR�����
Operation surrounding humidity �~���%
Safety EMC / Standard IEC/EN �����-�-�/�/�/�, IEC/EN �����-�, IEC/EN �����-�

- �� -
General Data
Display LCD����
Interface RS���/RS���/Wifi/LAN

- �� -
Model SUN-�K-G�� SUN-�K-G�� SUN-�K-G�� SUN-��K-G�� SUN-��K-G��

Input Side
Max.DC Power(kW) �.�kW ��.�kW ��.�kW ��kW ��.�kW
Max.DC Input Voltage(V) ����V
Start-up DC Input Voltage(V) ���V ���V
MPPT Operating Range(V) ���V~���V ���V~���V
Rated DC input voltage(V) ���V
MPPT Full Power Voltage Range(V) ���V~���V
Max.DC Input Current(A) ��A+��A
Max. Short Circuit Current (A) ��.�A+��.�A
Number of MPPT/Strings per MPPT �/�+�
MAX inverter backfeed current (A) �
Output Side
Rated Output Power(kW) �kW �kW �kW ��kW ��kW
Max.Active Power(kW) �.�kW �.�kW �.�kW ��kW ��.�kW
Rated AC Grid Voltage(V) �L/N/PE ���/���V ���/���V
AC Grid Voltage Range(V) �.��Un-�.�Un (this may vary with grid standards)
Rated Grid Frequency(Hz) ��/�� (Optional)
Operating Phase Three phase
Rated AC Grid Output Current(A) ��.�/��.�A ��.�/��.�A ��.�/��.�A ��.�/��.�A ��.�/��.�A
Max.AC Output Current(A) ��.�/��.�A ��.�/��.�A ��/��.�A ��.�/��.�A ��/��.�A
Maximum output fault ��.�A ��.�A ��.�A ��.�A ��.�A
current (a.c. A, peak )
Maximum output overcurrent ��.�A ��.�A ��.�A ��.�A ��.�A
protection (a.c. A,peak)
Output Power Factor �.� leading~�.� lagging
Grid Current THD <�%
DC Injection Current <�.�%
Grid Frequency Range ��-�� or ��-�� (Optional)
Efficiency
Max.Efficiency ��.�%
Euro Efficiency ��.�%
MPPT Efficiency >��%
Surge Protection DC Type II / AC Type II
General Data
���������
Cabinet Size(W*H*D) [mm] (Excluding connectors and brackets)
Weight(kg) ��
Topology Transformerless
Internal consumption <�W (Night)
Operating temperature -�� ~ ��℃,>��℃ derating
Ingress protection IP��
Noise Emission(Typical) ＜�� dB
Type Of Cooling Free cooling
Permissible Altitude (m) ����m
Warranty [year] Standard � years, extended warranty
VDE����, IEC�����/�����, VDE����, AS����.�, CEI � ��,
Grid Connection Standard
EN�����-�, G��, G��, C��-��, UNE������, NBR�����/NBR�����
Operation surrounding humidity �~���%
Safety EMC / Standard IEC/EN �����-�-�/�/�/�, IEC/EN �����-�, IEC/EN �����-�

- �� -
General Data
Display LCD����
Interface RS���/RS���/Wifi/LAN

����-��-�� Ver: �.�

- �� -
Add: No.�� South YongJiang Road, Daqi, Beilun, NingBo, China.
Tel: +�� (�) ��� ���� ����
Fax: +�� (�) ��� ���� ����
E-mail: [email protected]
Web: www.deyeinverter.com