WARNING!
IMPORTANT SAFETY INSTRUCTIONS
Please read the document completely before Installation or use
INSTALLATION GUIDELINES
This symbol alerts you that important literature concerning LASER RADIATION STEP 1: IDENTIFYING CORRECT TUBE CENTER
operation and maintenance has been included with this product The geometric center of tubes of most C arms do not coincide with the actual Image Center. The aim of step 1 is to have a
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
clear sticker on the tube corresponding to the image center. We shall use the Tube Stickers provided with the kit to
permanently mark this center position on the X ray tube cover using following process
This symbol identifies location of a laser aperture from which LASER
laser radiation is emitted.
1 – Take the Metal wire Cross provided in the kit and create a cross at the center of the imager. Most grids in imager have a
small dot at the center. Place the wires such that they intersect at the imager Center and stick it there. (See FIG 1)
- This apparatus uses batteries. In your community there might be regulations that require you to dispose of these
batteries properly under environmental considerations. Please contact your local authorities for disposal or recycling
- Take an Image shot. You shall get the cross Image on the monitor (See FIG 2)
information
- Do not dispose of batteries in fire
-Mark a dot on the Monitor (using a removable marker pen) corresponding to the intersection of the cross on the image.
- Do not short circuit, disassemble or overheat the batteries
This is the Imager Center as well as Image Center (See FIG 2) as represented on the monitor(FIG 3).
- Use the batteries with correct polarity in series as described within the battery box.
- Please use correct batteries (AA Type) in correct polarity and direction. Wrong polarity can lead to short circuit or FIG 1 FIG 2 FIG 3 FIG 4 FIG 5 FIG 6
damage.
- Do not drop or impart any mechanical shock to the product.
- Ensure the device is secured properly to the Imager before completion of installation
- Apparatus shall not be exposed to dripping or splashing. Use appropriate Sterile Drapes as defined in the User Manual. IMAGE OF THE CROSS A DOT IS MARKED ON PUT TUBE CENTER
METAL WIRES STUCK METAL WIRE CROSS IS
- Use of lens in the path of beam may concentrate the laser to a detrimental extent. Kindly avoid use of lens in the path of TO IMAGER SUCH THAT APPEARS ON THE THE MONITOR AT THE NOW PLACED ON TUBE IMAGE OF CROSS TO BE STICKER ON THE TUBE
the laser. THEY INTERSECT AT ITS MONITOR CENTER & MOVED AROUND IN MATCHED WITH DOT COVER AT THE SAME
CENTER FLURO SHOT. POINT
- The Laser Aimer is meant to indicate the center of beam within an accuracy range of +/- 5mm and is not meant for precise
aiming beyond specified tolerance
- Now take the Metal Wire Cross stuck on imager and place it on the Tube such that it approximately lies on the geometric
- Certain C arms may have excessive lateral C deflection when C is in complete over scan and in horizontal plane due to
center of the tube (See FIG 4). Take an X Ray Shot. It is most probable that the Cross mark on the screen does not match with
overhanging weight of the Imager. This may further impact the accuracy of laser as the C itself might deflect by up to 6mm
the Dot we marked on the monitor.
in such angulations only (measured on some real C arms)
- Figures and illustrations in the user manual are provided for reference only and may differ from the actual product
- Take a continuous fluro shot and move the Metal Wire Cross on the Tube so that the Image of the Metal Wire Cross
appearance.
matches the dot on the screen (See FIG 4 & 5)
- Disposal of the product at end of working life shall not be done with general waste. The Product shall
be properly stripped and parts separated and recycled to prevent poisoning of environment of - Once the mark on Monitor and the image of the Metal Cross match, it implies we have located the Image center on the
disposal. Please contact us for effective disposal of the product. Tube Cover. Mark this center with a marker pen. This mark represents the actual center of X ray cone that emerges from the
tube
CONTENTS OF THE LASER KIT - Carefully place the TUBE CENTER STICKER on it such that the intersection of the plus mark on the sticker coincides with the
point marked on the tube cover (see FIG 6)
The LASER KIT contains following items
LASER RING :1 per kit consisting of two pre-installed TUBE STICKERS: 2 per kit - The tube center which is true to the IMAGER and IMAGE CENTER is now identified and suitably marked for laser alignment.
Lasers of 650nm 5mW power and running on 4.5 V. ( one extra to allow assembly errors)
STEP 2: INSTALLATION OF THE LASER RING
- Remove the screw from top of both the laser covers as shown in FIG 7
- Release the laser cover by opening the snaps on the cover by accessing the snaps with a simple screw driver from the holes
in the backside of the device (FIG 8)
ALLEN KEY : One per kit FIG 7 FIG 8
SCREW DRIVER: 1 per kit
METAL WIRE CROSS: 1 per kit
RELEASE SNAPS (red) FROM
Apart from this, following additional parts are provided for exceptional cases where further adjustment of rubber pads BACKSIDE HOLES AND
may be required REMOVE COVER
REMOVE SCREW
STRIPS OF NEOPRENE RUBBER PAD: 2 strips QUICK FIX GLUE: 1 mini pack FROM TOP
INSTALLATION GUIDELINES INSTALLATION GUIDELINES
REPLACEMENT OF BATTERIES
- Open the screw on the battery box and replace batteries with AA size
1.5 V batteries in the polarity as mentioned Inside the box. Replace cover
and tighten screw after replacing batteries.
FIG 9 FIG 10
TROUBLESHOOTING
FIX LASER WITH BATTERY BOX FACING THE C SIDE AS SHOWN TIGHTEN THE SCREW INSIDE THE JOINT TILL LASER RING IS
PROPERLY SECURED
ISSUE ACTION TO BE TAKEN
- Install the laser on the Imager. Place the laser such that it is parallel to the edge of the Imager and the Battery Box faces the
Laser does not turn ON - Please check whether switch near the battery box is switched ON
C side. This is illustrated in FIG 9.
- Please check if batteries are to be replaced
- Please check if batteries are installed in correct order & sequence
- Ensure ring is properly secured by tightening the screw inside the joint as shown in FIG 10. Pull the ring down manually and
ensure it is secure, else add additional rubber strips given to tighten the ring around the device. - Register a Service call if none of the above works
Laser Ring does not sit tightly - Tighten the screw inside the joint till laser is secure as in Fig 10
STEP 3: ALIGNMENT OF THE LASER - Add extra rubber padding to increase tightening pressure
Laser not aligned to tube center - Ensure tube center marked on Tube cover is correct as in STEP 1
- Rotate the screws on left and right of the laser and adjust its angle so that the laser line emitted passes through the TUBE -Re Align the Laser and ensure the alignment screws hold the laser block
STICKER stuck on the tube. This is shown in FIG 11 tight as in FIG 11 post alignment.
ADJUSTMENT SCREWS ON BOTH ENDS Laser Cover seems loose. - Ensure laser cover is snapped back after alignment properly and top
Locking screw is in place.
- Register a service call if none of above works
Laser seems distorted/weak - Please see if exit window is stained/dirty or badly scratched
- Please verify laser quality after removing disposable drapes you are
Using. Laser quality shall be clean only with certain disposable drapes.
- Contact service center to identify best disposable drapes to use in
PRODUCT MAINTENANCE
PRODUCT MAINTENANCE GUIDELINES
FIG 11 : ADJUST LASER LINE SO THAT IT PASSES
LASER LINE - Always use product with Sterile Drapes in the Operating Theater.
THROUGH CROSS POINT ON TUBE STICKER
- Prevent spillage or accumulation of possibly infectious fluids during use of product
- Ensure screw is tightened from both sides once aligned so that it does not mis-align later
- Clean regularly with generic Sterilizing agents with a damp cloth. DO not spray liquid directly onto the device.
- Fit back the Laser covers by SNAPPING them back in and putting the screw on top by reversing the sequences as shown in
- Verify Laser is aligned to Tube sticker periodically to ensure accuracy of indication
FIG 8 & 7
- Remove batteries if the product is not to be used for long periods to prevent leakage/damage of batteries which may
- IMPORTANT NOTE: Once snapped back, the Laser Cover cannot be removed unless the ring is removed from the Imager.
affect product performance.
This is done to prevent tampering of laser alignment by stray people. Hence snap back the cover only when you are sure you
don't need to reopen for alignment.
- Laser is now ready to use through the switch besides the battery box.
English
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
FIG 7 FIG 8
LIBÉRATION LES
ENCLIQUETAGES (rouges)
DES TROUS ARRIÈRE ET
ENLEVER LA VIS DU RETIREZ LE COUVERCLE
HAUT
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
DIRETRIZ
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
RYS. 7 RYS. 8
ZWOLNIJ ZATRZASKI
(CZERWONE) Z TYLNYCH
OTWORÓW I ZDEJMIJ
USUNĄĆ ŚRUBY OD POKRYWĘ
GÓRY
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
SCHIȚĂ 2
IMAGINEA CRUCII
APARE PE MONITOR
SCHIȚĂ 7 SCHIȚĂ 8
ELIBERAȚI ZĂVOARELE
(ROȘII) DIN ORIFICIILE DIN
SPATE ȘI ÎNDEPĂRTAȚI
ÎNDEPĂRTAȚI CAPACUL
SCURTUL DIN SUS
SCHIȚĂ 9 SCHIȚĂ 10
FIXEAZĂ LASERUL CU CUTIA BATERIEI ORIENTATĂ STRÂNGEȚI ȘURUBUL ÎN INTERIORUL ARTICULAȚIEI PÂNĂ
SPRE PARTEA C, AȘA CUM ESTE ARĂTAT CÂND INELUL LASER ESTE BINE FIXAT
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
GAMBAR 9 GAMBAR 10
FIX LASER WITH BATTERY BOX FACING THE C SIDE AS SHOWN TIGHTEN THE SCREW INSIDE THE JOINT TILL LASER RING IS
PROPERLY SECURED
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
Картина 7 Картина 8
ЗНІМІТЬ ЗАЩЕЛКИ (ЧЕРВОНІ)
ІЗ ЗАДНІХ ОТВОРІВ І ЗНІМІТЬ
КРИШКУ
ЗНІМІТЬ ГВИНТ
ЗВЕРХУ
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
BILD 7 BILD 8
LÖSEN SIE DIE DRUCKKNÖPFE
(ROT) VON DEN HINTEREN
LÖCHERN UND ENTFERNEN SIE
SCHRAUBE VON DIE ABDECKUNG
OBEN ENTFERNEN
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
ДИАГРАМА 9 ДИАГРАМА 10
КРЕПЕНЕ НА ЛАЗЕР С КУТИЯТА ЗА БАТЕРИЯ, ЗАТЕГНЕТЕ ВИНТА ВЪТРЕ В ФУГАТА, ДОКАТО ЛАЗЕРНИЯТ
ОБРЪЩЕНА КЪМ СТРАНАТА C, КАКТО Е ПОКАЗАНО ПРЪСТЕН НЕ Е ПРАВИЛНО ОСИГУРЕН
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
LASER RADIATION
CLASS 1 LASER PRODUCT
As per IEC 60825-1:2014
LASER
1
dijagram 4 dijagram 6
KRIŽ OD METALNE ŽICE Stavite naljepnicu X-
SADA SE POSTAVLJA NA RAY COVER na X-RAY
POKLOPAC RTG I POMIĆE poklopac na istoj točki
TIJEKOM RTG
