A320-21-1208 R03 (2)
A320-21-1208 R03 (2)
SERVICE BULLETIN
REVISION TRANSMITTAL SHEET
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM: 21
ADDITIONAL WORK
**CONF ALL
No additional work is required by this revision for aircraft modified by any previous issue.
REASON
Revision No. 03 issued to incorporate changes found necessary and carried out during the
accomplishment of this Service Bulletin on aircraft with Manufacturer Serial Number (MSN) 2292, 2329,
2455, 2515, 2526, 2537, 2573, 2608, 2642, 2651, 2703, 2766, 2787, 3474, 3495, 3668, 3717, 3783,
3899, 3916, 3917, 3948, 4177, 4178, 4229, 4245, 4257, 4303, 4343, 4356, 4434, 4460, 4466, 4495,
4497, 4527, 4899, 4922, 5039 and 5211.
NOTE: This revision satisfies the requirements of the subsequent Technical Adaptation(s) (TA)
issued for the related Manufacturer Serial Number (MSN)s:
TA MSN
80341162/003/2017 2292, 2329, 2455, 2515, 2526, 2537,
2573, 2608, 2642, 2651, 2703, 2766,
2787, 3474, 3495, 3668, 3717, 3783,
3899, 3916, 3917, 3948, 4177, 4178,
4229, 4245, 4257, 4303, 4343, 4356,
4434, 4460, 4466, 4495, 4497, 4527,
4899, 4922, 5039 and 5211
CONF 004 added for MSNs that have not embodied MOD No. 151801P12216.
CHANGES
- Removal, Installation and Test work-steps for the Pack Controller Removed from
ACCOMPLISHMENT INSTRUCTIONS
Some revision bars are produced due to a text amendment to change "(Refer to...)" into "refer to".
Some revision bars are produced due to a text amendment to change "(Refer to...)" into "in accordance
with".
FRONT MATTER
AIR CONDITIONING - REMOVE CONFIGURATION UPDATED R
INTERFERENCES BETWEEN ACSC
AND LGCIU SIGNALS BY SHIELDING
OF 47HH AND 57HH WIRE
SUMMARY
MATERIAL PRICE INFORMATION MATERIAL PRICE INFORMATION TABLE R
UPDATED
MATERIAL PRICE INFORMATION TABLE R
UPDATED
MATERIAL PRICE INFORMATION TABLE R
UPDATED
MATERIAL PRICE INFORMATION TABLE ADDED N
EFFECTIVITY OPERATOR LIST UPDATED R
MANPOWER MANPOWER ADDED N
APPENDICES APPENDICES UPDATED R
Fig. A-FSAAA FIGURE SOLUTION UPDATED R
CONFIGURATION UPDATED
PLANNING INFORMATION
EFFECTIVITY EFFECTIVITY RELATED INFORMATION R
UPDATED
Configuration definition CONFIGURATION LIST UPDATED R
CONF 001 CONFIGURATION DEFINITION UPDATED R
CONF 003 CONFIGURATION DEFINITION UPDATED R
CONFIGURATION DESCRIPTION UPDATED
CONF 004 CONFIGURATION ADDED N
Material Effectivity MATERIAL EFFECTIVITY UPDATED R
CONFIGURATION UPDATED
FILING INSTRUCTIONS
This Service Bulletin has been generated electronically and is reissued as a complete document.
Replace the complete document.
Update the Kit references (administrative update) and to complete the Price and Availability.
Delete 3009VN of the paragraph PROCEDURE and of the Kit A01, A02, A03.
Update the elapsed time and illustration FAAAB (Gantt Chart) according to the testing time increase.
REVISION SEQUENCE
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
This summary is for information only and is not approved for modification of the aircraft.
ATA SYSTEM: 21
MODIFICATIONS
MODIFICATION CLASSIFICATION
MAJOR None
MINOR 153571K15409
NOTE: As per EASA IR 21, a minor change is one that has no appreciable effect on the
mass, balance, structural strength, reliability, operational characteristics affecting the
airworthiness of the product. All other changes are major changes.
REASON/DESCRIPTION/OPERATIONAL CONSEQUENCES
Experiences have shown that the sensors for monitoring the landing gear and the aft cargo door
give indications that do not agree with each other. This behavior is caused by an Electro Magnetic
Interference (EMI) effect across the sensor cables.
This Service Bulletin gives the necessary instructions to remove and install a new shielded cable from:
- Connector 241VC to connector 1943VC to prevent the EMI effect on sensors 32WV and 34WV.
- Connector 248VC-A to connector 1994VC to prevent the EMI effect on sensor 35GA.
The accomplishment of this Service Bulletin will increase the operational reliability of the related
sensors.
GENERAL EVALUATION
EVALUATION TABLE
COMPLIANCE RECOMMENDED (1) CANCELS INSPECTION SB NO
POTENTIAL AD NO A/C OPERATION AFFECTED NO
RELIABILITY AFFECTED NO PAX COMFORT AFFECTED NO
COST SAVING NO ETOPS AFFECTED NO
STRUCTURAL LIFE EXTN NO VENDOR SB INVOLVED NO
**CONF 001
**CONF 002
**CONF 003
**CONF 004
EFFECTIVITY
**CONF ALL
15T 16T 17M 20Q 24L 27V 31X 41N 45O 46U 48O 69X 74T
80X 89T 91X 95V 95W AAF AAR AAW AAY ABL ABQ ABY ACA
ACI ADR AEE AFL AFR AHY AIC AIJ ALK AMC AMU ANZ APJ
ASL ASV AUA AVA AWC AWW AXM AZA BAW BEC BEG BEL BER
BGF BGH BJN BKP BSX C2C CBG CBJ CCA CCM CEB CEF CES
CGH CHB CQH CQN CRK CSA CSC CSN CSZ CTV D2F DCS DKH
DLH DRK EIN ELB ESW ETD EVA EWE EWG EZY F2I FCB FFT
FHY FIA FJW FLI FTZ G8E GAF GAP GCR GFA GLG GMI GOW
GSW GWI HDA HKE HKJ HVN I2L IAW IBE IBS IGO ISR IYE
JAD JBU JCC JJP JSA JST JZR KAC KAY KFR KHO KKK KNE
KZR LAA LAN LAO LBT LGW LKE LLC LLM LLP LLX LWA LZB
MAC MEA MJF MJN MKR MLD MLM MON MOV MSC NIA NKS NLY
NMA NMB NWS OLY OMS ONE ORF OTC PAL PGT PIA PIC QQE
QTR RBA RBG RJA SAA SAI SAS SBI SDM SDR SFJ SHU SKU
SLK SNG SSG SUD SVA SVR SVW SWM SWR TAE TAI TAM TAP
TAR TBA TGW THD THY TJS TTW UAE UAL UEA UKN UNA USA
UZB VIP VIV VJC VLG VOE VOI VRD VRE VVC WHT WOW WZZ
CONCURRENT REQUIREMENTS
None
REFERENCES / REPERCUSSIONS
TFU None
OEB None
AOT None
SIL None
ISI None
LINE MAINTENANCE AFFECTED No
LIFE LIMIT None
OTHER None
AIRCRAFT YES
EQUIPMENT NO
HARD NO
SOFT NO
OBRM NO
MANPOWER
**CONF 001
**CONF 002
**CONF 003
**CONF 004
APPENDICES
**CONF ALL
2M
FR35
1M
FR32
N_SB_211208_5_SAAA_01_00
**CONF 002
FR35.6
2M
FR35.7
1M
N_SB_211208_5_SAAB_01_00
**CONF 003
2M
1M
FR34
FR30
N_SB_211208_5_SAAC_01_00
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX
FRANCE
Tel : (33) 5 61 93 33 33
Telex : AIRBU 530526F
Fax : (33) 5 61 93 42 51
ATA SYSTEM: 21
1. PLANNING INFORMATION
**CONF ALL
A. EFFECTIVITY
This modification is embodied before delivery on aircraft with Manufacturer Serial Number
(MSN) 5220 and subsequent for A320, on aircraft with MSN 5265 and subsequent for A321,
on aircraft with MSN 5267 and subsequent for A319 and on aircraft with MSN 5478 and
subsequent of A318.
(1) Models
2037 2043 2050 2053 2062 2119-2120 2129 2170 2176 2181 2184 2196 2213-2214
2224 2228 2230 2245 2249 2251 2265 2268 2271 2277 2279 2281 2283 2289 2292
2296 2299-2300 2306 2308 2319 2322 2326 2329 2335 2338 2346 2353-2355
2360-2362 2366 2370 2375-2376 2378-2380 2383 2385 2387 2392 2395-2396 2398
2400-2402 2404 2406 2412-2414 2417-2420 2423 2427 2431 2433-2434 2436
2438-2444 2446 2448 2450 2452-2453 2455-2457 2460 2463 2465 2467-2471 2473
2475-2477 2481 2483-2485 2487 2490 2492 2495-2497 2501-2503 2506 2511-2516
2518-2519 2522 2524 2526-2529 2531 2537-2541 2545-2546 2548 2550-2551
2553-2561 2564-2567 2569 2571-2574 2576 2578-2579 2581 2584-2588 2590
2592-2593 2596 2598 2600 2602-2605 2607-2612 2614 2616-2617 2619-2626
2628-2629 2631-2634 2636-2638 2642-2646 2648-2651 2653-2662 2664-2668 2670
The Operator/MSN relationship is provided for information only and is correct at the time
of issue in accordance with the information available to AIRBUS. Any future changes
resulting from transfer of an aircraft from one operator to another will not be reflected in
this list unless the Service Bulletin is revised for another reason.
OPERATOR MSN
15T 3261
16T 4024 4679
17M 3856
20Q 4842
24L 3604 3865
27V 3826
31X 4319
41N 3164
45O 5040
46U 2906 2952 2982 3275 3296 3332 3674 3734 3986 4053 5218
48O 3362 3412
69X 2245
74T 4768
80X 2748
89T 3356
91X 2837
95V 3379
95W 2949 4199
AAF 3136 3242 3289 4589 4675 4758 4767
AAR 3437 3483 3496 3641 3873 4112 5169 5173
AAW 3224 3236 3615 3657 4004 4521
AAY 2170 2176 2224 2265 2271 2289 2300 2319 2387 2398 2420 2427
2450 2556 2586 2625 2638 2702 2709 2729 2786 2790 2821 2831
2876 2932 2995 3076 3079 3084 4015 4057 4104 4115 4122 4135
ABL 2732 2808 2840 2927 2933 2943 3297
ABQ 3974
ABY 4468 4524 4958 5017
ACA 3051 3401 3884 5038
OPERATOR MSN
ACI 3547
ADR 4282 4301
AEE 2468 2553 2610 2828 3033 3066 3074 3162 3302 3316 3322 3365
3392 3423 3439 3462 3478 3484 3519 3526 3527 3709 3714 3745
3748 3753 3773 3785 3812 3820 3829 3850 3878 3990 4065 4094
4165
AFL 3157 3267 3334 3373 3511 3545 3574 3627 3631 3640 3644 3699
3711 3778 3786 3835 3923 3954 4058 4074 4099 4103 4116 4133
4148 4160 4453 4461 4498 4500 4579 4625 4649 4656 4684 4692
4712 4835 5044 5059
AFR 2456 2705 2716 2721 2938 2961 3008 3098 3372 3399 3419 3420
3441 3470 3777 3795 3814 3825 3859 3930 4063 4084 4105 4137
4139 4241 4251 4267 4295 4298 4335 4402 4601 4604 4664 4714
4747 4800 4820 4901 4908 5084 5129
AHY 2487 2516 2588 2685 2788 2846 2853 2865 2991 3006
AIC 2593 2624 2629 2907 3130 3146 3212 3271 3288 3300 3305 3326
3340 3344 3367 3498 3551 3557 3573 3619 3620 3687 3752 3792
3822 3874 3918 3955 3970 4002 4009 4020 4029 4052 4078 4089
4096 4121 4138 4155 4164 4201 4212 4236 4237 4280
AIJ 2539 2930 2964 3021 3044 3123 3149 3160 3286 3304 3312 3374
3508 3514 3667 3690 4235 4304 4411 4730 4733 4924 4933 5163
ALK 2731 3397 3636 4694 4869 4915 5086
AMC 2665 2768 3056 3068
AMU 4197
ANZ 4553 4584 4884 4926
APJ 4887 4936 5015 5166
ASL 2277 2296 2335 2587 2621 2645 3252 3317
ASV 4142 5035
AUA 3295 3482 3502 3515 3532 5122 5181
AVA 3647 3664 3691 3961 3980 3988 3992 4001 4011 4026 4046 4051
4167 4200 4281 4284 4345 4381 4567 4763 4789 4821 4862 4939
5057 5119 5195
AWC 2564 2791 3830 4701
AWW 3364 3403
AXM 2612 2633 2656 2683 2699 2760 2816 2826 2842 2881 2885 2956
2989 3000 3018 3052 3064 3117 3140 3154 3173 3182 3194 3201
3223 3232 3277 3291 3299 3327 3338 3353 3370 3394 3404 3427
3448 3477 3486 3489 3505 3521 3536 3549 3568 3576 3582 3610
3628 3679 3701 3715 3729 3758 3765 3776 3813 3875 3963 3997
4019 4035 4070 4079 4088 4098 4126 4147 4263 4278 4293 4302
4333 4346 4361 4367 4386 4390 4404 4426 4458 4462 4477 4486
4557 4562 4571 4582 4641 4727 4793 4797 4807 4815 4882 4889
4917 4964 4969 4979 4980 4989 5109 5137 5149 5153 5165 5200
5215
AZA 2869 3115 3343 3563 3598 3609 3643 3666 3695 3732 3815 3846
3885 3906 3921 3956 3976 3978 4075 4108 4119 4143 4152 4195
4249 4520 4523 4536 4759 4764 4859 4875 4910 5018 5130
OPERATOR MSN
BAW 2441 2653 2694 2697 2720 2799 2981 3049 3081 3089 3235 3254
3290 3301 3314 3351 3468 3499 3512 3550 3607 3649 3697 3703
3721 3726 3912 3926 4185 4238 4265 4306 4464 4551 4725 4791
4975
BEC 3199
BEG 3139
BEL 2196 2230 2392 2400 2700 2763 2925 3161 3255 3790 3895 4243
4275
BER 2668 3945 3995
BGF 3188
BGH 2844 2863 3125
BJN 4956
BKP 2362 2366 2383 2417 2467 2531 2600 2634 2648 2660 2664 2783
3421 3424 3454 3672 3694 3759 3911
BSX 3577
C2C 5023 5088
CBG 4970
CBJ 2557 2561 2611 2644 2733 2985 3285 3520 3548 3561 3578 3580
3638 3842 3851 3914 3958 3982 4388 4410 4412 4428 4440 4471
4483 4505 4513 4529 4540 4580 4602 4677 5008 5072 5114 5185
5216
CCA 2545 2551 2559 2614 2643 2805 2819 2839 2847 2890 3195 3200
3215 3221 3226 3250 3307 3329 3337 3461 3506 3523 3601 3623
3653 3655 3665 3678 3722 3725 3766 3806 3940 3973 4022 4031
4062 4091 4131 4180 4221 4283 4317 4318 4348 4377 4472 4473
4494 4538 4566 4593 4617 4719 4771 4775 4803 4829 4834 4873
4895 4900 4949 4963 4985 4997 5014 5032 5054 5091 5124 5174
5199
CCM 3325 3882 3952
CEB 2852 2994 3048 3272 3762 3767 4447 4508 4537 4574 4852 4861
4870 4927 4993 5045 5067
CEF 2801 3085
CES 2693 2757 2825 2882 2895 3168 3170 3186 3197 3233 3247 3249
3262 3471 3481 3559 3593 3611 3612 3613 3639 3650 3677 3682
3692 3716 3775 3793 3797 3870 3904 3929 3937 3965 3969 4027
4037 4043 4045 4111 4144 4186 4198 4209 4220 4239 4240 4252
4297 4309 4340 4342 4355 4374 4423 4627 4638 4659 4685 4702
4709 4711 4718 4722 4723 4729 4746 4748 4765 4769 4776 4799
4831 4844 4857 4877 4886 4903 4938 4946 4967 4987 5047 5048
5053 5063 5135 5136 5144 5156 5192 5210 5227
CGH 3768 3849 4522
CHB 4231 4262 4452 4482 4569 4644 4686 4687 4995 5105
CQH 2939 3014 3023 3747 3819 4072 4093 4168 4244 4331 4366 4373
4375 4499 4586 4738 4750 4760 4809 4816 4909 4978 4983 5022
5051 5108
CQN 3828 3836 3876 3901 3903 3941 4140 4172 4696
CRK 5147 5189
CSA 3043 3094 3406 3436 3452 3660 3892 4258 4713
OPERATOR MSN
CSC 2431 3114 3116 3124 3158 3167 3196 3210 3386 3449 3583 3591
3680 3730 3893 3962 3996 4018 4068 4288 4326 4378 4420 4424
4525 4575 4619 4642 4660 4707 4731 4824 4830 4856 4905 4911
4923 5041 5121 5141 5160 5197 5208 5233
CSN 2354 2361 2484 2506 2511 2519 2541 2546 2554 2555 2558 2574
2579 2637 2701 2708 2713 2741 2743 2759 2767 2770 2772 2796
2809 2824 2834 2855 2861 2877 2899 2915 2936 2950 2960 2971
2986 3067 3075 3112 3217 3241 3251 3459 3493 3507 3552 3566
3587 3645 3681 3764 3784 3847 3860 3867 3890 3910 3920 3934
3938 3951 3959 3981 3983 3999 4003 4017 4036 4038 4071 4184
4189 4194 4205 4217 4224 4225 4230 4232 4248 4260 4266 4271
4274 4279 4290 4292 4299 4322 4325 4338 4341 4350 4362 4365
4369 4370 4387 4396 4416 4430 4456 4507 4550 4613 4671 4751
4782 4794 4808 4836 4854 4864 4880 4883 4912 4919 4928 4982
5061 5151 5168 5170 5183 5202 5214 5237
CSZ 2672 2684 2841 2905 2909 2935 2973 2980 3131 3132 3153 3206
3366 3383 3435 3440 3456 3528 3599 3696 3698 3756 3848 3855
3887 3898 3935 3971 4010 4028 4159 4176 4208 4214 4226 4300
4359 4407 4409 4435 4474 4514 4531 4620 4633 4666 4726 4845
4866 4876 4897 4920 4929 4977 4986 5002 5082 5110 5176
CTV 2598 2692 3147 3148 3861 4961
D2F 2747
DCS 3243
DKH 2975 3027 3234 3268 3368 3485 3596 3605 3967 3984 4064 4102
4154 4276 4401 4429 4573 4587 4652 4833 4840 4981 5013 5070
5071 5131
DLH 3265 3339 3360 3387 3434 3592 3625 3864 3936 3987 4005 4016
4047 4054 4073 4085 4097 4120 4141 4153 4182 4191 4261 4289
4324 4332 4360 4363 4398 4449 4455 4511 4545 4560 4585 4607
4626 4672 4710 4753 4792 4796 4819 4841 4881 4916 4976 4994
5028 5049 5087 5186 5203 5239
DRK 2306 2346
EIN 3129 3174 3318 3345 3501 3755 3781 3789 3823 3857 4572 4634
4678 4715
ELB 3705
ESW 3513
ETD 3004 3050 3676 3693 3713 3902 4066 4077 4124 4934 5095
EVA 5261
EWE 2813 3352 3358 4227 4256 4285 4368 4565 4606 4631 4998
EWG 2749 2867 3080 3093 3121 3178 3213 3328 3422 3464 3516 3540
3594
OPERATOR MSN
EZY 2037 2043 2050 2120 2181 2184 2353 2360 2370 2385 2402 2412
2463 2471 2477 2481 2492 2495 2503 2512 2514 2527 2528 2538
2565 2578 2605 2636 2646 2677 2681 2691 2715 2727 2735 2742
2744 2754 2765 2769 2777 2779 2782 2795 2803 2812 2818 2827
2829 2854 2860 2866 2873 2884 2923 2946 2959 2968 3003 3036
3041 3053 3055 3059 3061 3082 3088 3090 3118 3122 3134 3137
3176 3184 3411 3413 3426 3432 3442 3466 3537 3544 3555 3569
3571 3608 3634 3675 3683 3702 3720 3735 3742 3746 3754 3763
3774 3788 3799 3805 3808 3810 3824 3843 3844 3845 3854 3871
3888 3909 3913 3922 3946 3953 3975 3979 3991 4006 4012 4013
4014 4033 4034 4040 4048 4056 4069 4076 4080 4087 4125 4129
4132 4157 4179 4196 4219 4233 4234 4250 4286 4313 4316 4327
4380 4385 4418 4425 4427 4437 4444 4451 4554 4556 4581 4588
4591 4594 4624 4635 4636 4640 4646 4667 4676 4680 4693 4705
4708 4717 4721 4740 4744 4749 4778 4781 4785 4787 4837 5019
5020 5046 5052 5056 5064 5104 5111 5113 5116 5138 5146 5150
5187 5201
F2I 2308 3853
FCB 2662 2875 2920 3259
FFT 2406 2448 2483 2518 2695 2806 2836 2857 3205 3389 3431 4127
4204 4253 4254 4272 4307 4668 4688 4704 4745
FHY 2524 3025 3852 3891 4207 4658 5096
FIA 3581
FJW 2281
FLI 3905 5079
FTZ 2268
G8E 2718
GAF 3897 4060
GAP 3087 3187 3273 3310 3455 3731 4777 4984 5007 5012 5103
GCR 2338 2475 4600 4739 4825 5006 5117
GFA 4030 4059 4083 4146 4158 4188 4218 4255 4502 4541 4780 4827
4860 4865 5025 5074 5171 5175 5180 5257
GLG 3408 3467 3518 4100 4379 4487 4547 4599
GMI 3019 3407 3533 3560 3689 3872 3950 4268 4663 4691 5085
GOW 3063 3306 3597 3616 3798 3827 3900 3915 3972 5016 5112
GSW 3589 3818
GWI 2607 2628 2632 2833 2976 3011 3128 3172 3193 3375 3500 3534
3839 3841 4166 5043
HDA 3369 3669 4023 4247 5024 5030
HKE 2299 2322 2717 4181 4445
HKJ 2706 3073
HVN 2974 3005 3013 3022 3198 3315 3355 3600 3737 3862 3964 3966
4136 4213 4277 4311 4315 4669 4703 4737 4783 4826 4863 4945
4971 5164 5241 5247 5251
I2L 2730 2739 2793
IAW 4044 4067
IBE 2736 2756 2843 2889 2897 2996 3078 3209 3278 3320 3380 3443
3651 3744
OPERATOR MSN
IBS 2807
IGO 2457 2584 2609 2626 2649 2712 2737 2804 2914 3138 3264 3308
3330 3357 3414 3453 3457 3497 3541 3618 3750 3782 3863 3943
4008 4113 4156 4216 4294 4312 4328 4384 4399 4433 4438 4481
4488 4506 4510 4518 4535 4552 4603 4609 4614 4630 4637 4752
4757 4762 4813 4818 4868 4888 4947 4954 4965 5027 5036 5073
5076 5080 5090 5092 5094 5120 5155 5158 5188 5190 5194
ISR 4354 4413
IYE 4653 4690
JAD 2764 3246
JBU 3381 3416 3451 3479 3488 3517 3554 3572 3622 3659 3707 3724
3760 3800 3811 4578 4612 4647 4904 5060 5142 5148
JCC 4128
JJP 5093 5145 5161
JSA 2423 2453 2604 4443 4515 4772 4786 4872 4914
JST 2292 2329 2455 2515 2526 2537 2573 2608 2642 2651 2703 2766
2787 3474 3495 3668 3717 3783 3899 3916 3917 3948 4177 4178
4229 4245 4257 4303 4343 4356 4434 4460 4466 4495 4497 4527
4899 4922 5039 5211
JZR 3919 3939 4162 5033
KAC 3957
KAY 3046 4470
KFR 2650
KHO 2957 2965
KKK 5115
KNE 2569 2776 3218 3256 3361 3396 3425 3475 3787 3802 3809 3817
3868 3889 3894 3933 4055 4061 4699 4735
KZR 3141 3614
LAA 4405 4490 4526
LAN 2572 2585 2845 2858 2864 2872 2886 2892 2894 3280 3319 3535
3556 3663 3671 3770 3772 3779 4383 4400 4439 4476 4509 4516
4543 4546 4549 4576 4597 4598 4605 4657 4697 4839 4871 4892
4896 4921 4943 4972 5005 5097 5125 5178 5213
LAO 4596 4639
LBT 3480 3487 4623
LGW 3202 3245 3415 3447 3661 3700 3704 3728
LKE 2581 2617 2746 3240 5100 5172
LLC 2987 4203 4489
LLM 2413 2419 2439 2571 2688
LLP 2903 2912 3191
LLX 2529 2619
LWA 2878 2954
LZB 2540 2596 3309 3564 3780
MAC 4539 4568 4806 4848 5143 5206
MEA 3736 3804 3837 4296 4339 4632 5000 5152 5162
MJF 3402 4353
MJN 3723 4117 4795
OPERATOR MSN
MKR 2784 3522
MLD 2849
MLM 4622
MON 3293 3546 3575
MOV 2442 2446
MSC 2937 2966 3282 3323 3626 3840 4320
NIA 2476 2874 3183 3219 3925 4310
NKS 2433 2470 2473 2485 2490 2560 2567 2603 2622 2673 2679 2698
2704 2711 2723 2797 2893 2898 2929 2942 2963 2978 2983 3007
3017 3026 3165 3393 3395 4206 4264 4321 4403 4422 4431 4548
4592 4595 4902 4951 4996 5029 5042 5132 5159
NLY 2902 3504 3708 3749 3908 4161 4187 4269 4329 4334 4728 5126
5133
NMA 2676
NMB 3346 3586
NWS 3034 3120 3458
OLY 2396
OMS 3035 3047 3111
ONE 4222 4287 4336 4891 4913 4941 4942 5193
ORF 2566 4992
OTC 5209
PAL 3553 3579 3652 5081 5140
PGT 3831 4175
PIA 2719 2758 2789 2926 2944 3031 3060 3097
PIC 2670 2922 3012 3621 4459 4533
QQE 3994 4114 4170
QTR 3274 4110 4130 4173 4183 4382 4406 4436 4479 4496 4530 4615
4700 4754 4784 4802 4810 4858 4930 4968 5010 5078 5127 5217
RBA 3071
RBG 3152 4890
RJA 2953 3428 3685 3803 3832 4670 4817 4853 5099 5128 5177
SAA 2326 2355 2375 2379 2418 2438 2469 2501 4990 5011
SAI 2404 2414 2452 2496 2502 2631 2655 2738 3105 3270
SAS 2817 2850 2856 2883 2888 2911 2958 2990 3086 3159 3192 3227
3231 3292 3335
SBI 2279 3446 3473 3490 3494 3866 3880 4032 4150 5001 5026 5031
5106 5134 5167
SDM 2465 2497 2751 2879 2913 3065 3179 3794 3942 3998
SDR 4953 4974
SFJ 4555 4720 5102
SHU 3108 3281 3298 3336 3838
SKU 2119 2129 2214 2249 2251 2283 2378 2380 2436 2460 2548 3171
3331
SLK 2775 3570 4118 4215 4259 4457 5050 5089
SNG 4611 4648
SSG 2550
OPERATOR MSN
SUD 3040
SVA 4081 4090 4092 4273 4314 4337 4349 4357 4364 4376 4391 4392
4393 4394 4397 4408 4414 4419 4432 4442 4454 4467 4484 4501
4517 4519 4542 4564 4577 4590 4811 4823 4838 4925 4955 4962
5009 5065
SVR 2376 2590 2623 2707 2862 2947 2998 3099 3107 3189 3385 3388
3410 3433 3472 3834 5055
SVW 2592 3133 3542
SWM 2689
SWR 4534 4618 4673 5037 5069
TAE 2659
TAI 2434 2444 2687 2917 3042 3057 3103 3113 3248 3276 3378 3418
3510 3538 3869 4906 4944 5068 5219
TAM 2513 2734 2838 2859 2887 2896 2904 2924 3002 3032 3058 3156
3180 3211 3222 3229 3266 3284 3294 3313 3391 3565 3588 3595
3630 3658 3662 3710 3727 3733 3761 3816 4000 4163 4171 4192
4352 4358 4389 4441 4446 4465 4544 4563 4570 4662 4734 4756
4773 5066 5101 5107 5184
TAP 2792 2822 2870 3769 3883 4021 4095 4106 4145 4742
TAR 3096 4344 4689 5204
TBA 4766 4801 4846 5157 5256
TGW 2724 2728 3757 3801 4210 4421 4469 4491 4493 4532 4561 4608
4645 4812 4879 4918 4931 4973
THD 5198
THY 2395 2401 2522 2602 2823 2868 2916 2919 2928 2934 2984 2999
3010 3015 3126 3142 3185 3207 3208 3239 3257 3283 3303 3341
3350 3382 3405 3429 3525 3539 3558 3567 3603 3637 3654 3673
3688 3718 3719 3738 4042 4629 4643 4654 4665 4682 4695 4698
4706 4755 4761 4774 4779 4788 4790 5077 5083 5118 5154 5205
5254
TJS 3632
TTW 4804 4874
UAE 4822
UAL 2667 2680 2714 2815 2901 2940 2948 2969 3020 3144 3258 3269
3311 3342
UEA 2654 2696 2762 2774 2820 2835 3024 3706 4347 4743 4988 5003
5191
UKN 3260
UNA 2921 4228 4583
USA 3584 3629 3633 3712 3740 3796 3858 3879 3881 3924 3928 3944
3960 3977 3989 3993 4025 4041 4050 4082 4086 4107 4123 4134
4149 4202 4242 4843 4847 4850 4885 4893 4898 4932 4935 4940
4957 4960 4966 5235 5244
UZB 4371 4395 4417 4485 4492 4528 4651 4724 4770 4952
VIP 4151
VIV 2443 2576 2661 2752 2908 3743
VJC 2745 3646 3739 3791 4049 4190 4193 4415 4475 4504 4512 4907
OPERATOR MSN
VLG 2620 2658 2678 2753 2761 2785 2794 2798 2962 2988 3028 3054
3083 3095 3102 3109 3145 3151 3169 3203 3237 3321 3376 3377
3400 3444 3476 3492 3529 3833 3907 4101 4291 4463 4478 4661
4674 4681 4849 4855 4937
VOE 2053 2062
VOI 2657 2666 2771 2780 2979 2997 3045 3069 3077 3175 3253 3279
3450 3463 3491 3524 3543 3590 3624 4741 4798 4828 4832 4950
5062 5207 5212
VRD 2616 2674 2740 2773 2778 2800 2811 2830 2851 2993 3016 3037
3101 3135 3155 3181 3204 3230 3324 3347 3349 3359 3398 3417
3445 3460 3465 3503 3656 3670 3684 3686 4448 4480 4558 4559
4610 4616 4655 4805 4814 4851 4867 4894 4948 4959 4991 4999
5004 5034 5058 5179
VRE 2213 2228
VVC 3896 3931 3949
WHT 2440 2675
WOW 4270 4305
WZZ 3127 3143 3166 3177 3354 3384 3409 3430 3531 3562 3741 3771
3807 3877 3927 3947 3968 4109 4174 4223 4246 4308 4323 4351
4372 4621 4628 4683 4716 4736 5021 5075 5123 5139 5196
MSN CONFIGURATION
2037 2043 2050 2053 2062 2119 2120 2129 2170 2176 2181 003
2184 2196 2213 2214 2224 2228 2230 2245 2249 2251 2265
2268 2271 2277 2279 2281 2283 2289 2296 2300 2306 2308
2319 2326 2335 2346 2353 2355 2360 2362 2370 2375 2378
2379 2380 2383 2385 2387 2392 2396 2398 2400 2402 2404
2406 2412 2414 2418 2420 2427 2431 2433 2436 2438 2440
2442 2444 2446 2448 2450 2452 2456 2460 2463 2465 2467
2468 2469 2470 2471 2473 2477 2481 2483 2485 2487 2490
2492 2495 2497 2501 2503 2512 2514 2516 2518 2519 2527
2528 2538 2541 2545 2546 2548 2550 2551 2554 2555 2556
2557 2558 2559 2560 2561 2565 2567 2572 2574 2578 2579
2581 2585 2586 2588 2592 2593 2603 2605 2607 2611 2614
2617 2621 2622 2624 2625 2628 2629 2631 2632 2634 2636
2638 2643 2644 2646 2648 2650 2655 2657 2659 2660 2662
2664 2666 2667 2672 2673 2675 2677 2679 2681 2684 2691
2693 2694 2697 2698 2700 2702 2704 2706 2709 2711 2715
2716 2718 2720 2723 2727 2729 2733 2735 2738 2739 2742
2744 2746 2748 2751 2754 2757 2762 2763 2765 2769 2771
2773 2774 2777 2779 2780 2782 2784 2786 2788 2790 2795
2797 2801 2803 2805 2806 2811 2812 2813 2815 2818 2819
2821 2825 2827 2829 2831 2833 2836 2837 2839 2841 2843
2845 2847 2849 2850 2852 2854 2857 2858 2860 2864 2866
2870 2872 2873 2876 2878 2879 2884 2886 2887 2888 2889
2890 2892 2893 2894 2897 2898 2901 2905 2907 2913 2921
2923 2925 2929 2935 2938 2940 2942 2946 2948 2949 2954
2959 2961 2963 2969 2976 2978 2979 2981 2983 2985 2997
3003 3007 3011 3017 3019 3020 3024 3026 3028 3032 3036
3041 3043 3045 3046 3049 3053 3054 3057 3059 3061 3065
3069 3073 3077 3078 3082 3084 3085 3088 3090 3094 3096
3102 3108 3114 3116 3118 3122 3124 3128 3133 3134 3137
3139 3142 3144 3165 3168 3169 3171 3172 3175 3176 3179
3181 3184 3186 3188 3193 3195 3200 3202 3204 3209 3226
3231 3243 3245 3248 3250 3252 3253 3255 3258 3260 3269
3271 3276 3279 3281 3285 3288 3292 3298 3300 3305 3309
3311 3317 3320 3324 3331 3336 3342 3344 3346 3347 3352
3356 3358 3364 3375 3377 3380 3385 3388 3393 3395 3403
3406 3407 3411 3413 3415 3417 3421 3424 3426 3428 3432
3436 3442 3443 3445 3447 3450 3452 3454 3463 3466 3467
3491 3500 3513 3518 3520 3533 3534 3537 3542 3544 3548
3551 3555 3560 3561 3564 3569 3571 3578 3580 3586 3588
3589 3590 3595 3604 3608 3614 3615 3620 3632 3634 3638
3647 3651 3657 3660 3661 3663 3671 3675 3680 3683 3684
3685 3686 3687 3689 3691 3694 3700 3702 3704 3705 3710
3720 3727 3728 3733 3735 3742 3744 3746 3754 3757 3759
3763 3768 3770 3772 3774 3779 3788 3790 3794 3799 3801
3803 3808 3810 3818 3822 3824 3826 3828 3832 3834 3836
3838 3839 3841 3842 3844 3845 3849 3851 3853 3854 3856
3860 3865 3872 3874 3876 3888 3890 3892 3895 3897 3901
3903 3905 3911 3914 3918 3942 3950 3957 3958 3962 3970
MSN CONFIGURATION
3982 3983 3994 3998 4000 4004 4018 4020 4024 4029 4036 003
4038 4040 4042 4048 4052 4056 4060 4069 4071 4076 4080
4087 4089 4114 4121 4125 4127 4129 4132 4141 4151 4163
4164 4166 4171 4182 4192 4200 4204 4215 4222 4227 4228
4254 4256 4258 4259 4262 4268 4275 4282 4285 4287 4301
4313 4319 4327 4332 4336 4353 4380 4385 4389 4403 4410
4418 4422 4425 4427 4428 4437 4444 4451 4452 4455 4470
4511 4522 4529 4563 4583 4598 4605 4622 4624 4629 4635
4640 4660 4663 4665 4667 4679 4691 4693 4695 4705 4713
4717 4734 4744 4755 4756 4759 4764 4766 4768 4773 4774
4778 4781 4785 4787 4790 4796 4801 4822 4837 4841 4842
4846 4859 4871 4875 4910 4956 4992 4995 4998 5005 5018
5023 5040 5043 5057 5079 5085 5088 5097 5105 5119 5130
5157 5193 5208 5219 5239 5256 5261
MSN CONFIGURATION
2292 2299 2322 2329 2338 2354 2361 2366 2376 2395 2401 001
2413 2417 2419 2423 2434 2439 2441 2443 2453 2455 2457
2475 2484 2496 2502 2506 2511 2513 2515 2522 2524 2526
2529 2531 2537 2539 2540 2564 2566 2569 2571 2573 2576
2584 2587 2596 2598 2600 2602 2604 2608 2609 2612 2616
2619 2620 2623 2626 2633 2637 2642 2645 2649 2651 2654
2656 2658 2661 2665 2668 2670 2674 2676 2678 2680 2683
2685 2688 2689 2692 2695 2696 2699 2701 2703 2705 2708
2712 2714 2717 2719 2721 2724 2728 2731 2732 2734 2737
2740 2743 2745 2747 2749 2752 2753 2758 2760 2761 2764
2766 2768 2770 2772 2775 2776 2778 2783 2785 2787 2789
2791 2792 2794 2796 2798 2800 2804 2807 2808 2816 2817
2820 2822 2824 2826 2828 2830 2834 2835 2838 2840 2842
2844 2846 2851 2853 2855 2856 2859 2861 2863 2865 2867
2869 2874 2875 2877 2881 2883 2885 2896 2899 2902 2904
2906 2908 2909 2911 2914 2915 2917 2920 2922 2924 2926
2928 2930 2932 2934 2937 2939 2943 2944 2947 2950 2952
2953 2956 2958 2960 2962 2964 2966 2968 2973 2975 2980
2982 2984 2986 2987 2988 2989 2990 2991 2993 2994 2995
2998 3000 3002 3004 3006 3008 3010 3012 3014 3016 3018
3021 3023 3025 3027 3031 3033 3035 3037 3040 3042 3044
3047 3048 3050 3052 3055 3056 3058 3060 3063 3064 3066
3068 3071 3074 3076 3079 3080 3083 3086 3087 3089 3093
3095 3097 3099 3101 3103 3105 3107 3109 3111 3113 3115
3117 3121 3123 3125 3127 3129 3131 3132 3135 3136 3138
3140 3141 3143 3145 3147 3148 3149 3151 3152 3153 3154
3155 3156 3157 3158 3159 3160 3161 3162 3164 3166 3167
3170 3173 3174 3177 3178 3180 3182 3183 3185 3187 3189
3192 3194 3196 3197 3199 3201 3203 3205 3206 3208 3210
3211 3213 3215 3218 3219 3221 3223 3224 3227 3230 3232
3234 3236 3237 3239 3240 3242 3246 3256 3257 3259 3261
3264 3266 3268 3270 3272 3273 3275 3277 3278 3280 3282
3284 3286 3289 3291 3293 3295 3296 3299 3301 3303 3304
3306 3308 3310 3312 3313 3314 3316 3318 3319 3321 3323
3325 3327 3328 3330 3332 3335 3337 3338 3341 3343 3345
3349 3351 3353 3354 3357 3359 3361 3362 3365 3366 3368
3370 3373 3374 3376 3378 3379 3381 3383 3384 3386 3389
3391 3392 3394 3396 3398 3400 3402 3404 3408 3409 3410
3412 3414 3416 3418 3420 3422 3423 3425 3427 3430 3431
3433 3435 3437 3439 3440 3444 3446 3448 3449 3451 3453
3455 3456 3457 3460 3461 3464 3465 3468 3470 3472 3473
3474 3475 3476 3477 3478 3479 3480 3481 3482 3483 3484
3485 3486 3487 3488 3489 3490 3492 3494 3495 3496 3497
3499 3501 3502 3503 3505 3506 3508 3510 3511 3514 3515
3516 3517 3519 3521 3524 3526 3528 3529 3531 3532 3535
3536 3538 3540 3541 3543 3545 3547 3549 3550 3553 3554
3556 3558 3559 3562 3563 3565 3567 3568 3570 3572 3574
3576 3577 3579 3581 3582 3591 3594 3596 3597 3598 3599
3601 3603 3605 3607 3609 3610 3611 3613 3616 3618 3621
3622 3624 3626 3627 3628 3630 3631 3640 3641 3643 3644
3646 3649 3650 3652 3654 3656 3658 3659 3662 3664 3666
MSN CONFIGURATION
3667 3668 3670 3672 3674 3676 3677 3679 3690 3692 3693 001
3695 3696 3697 3698 3699 3701 3703 3706 3707 3709 3711
3713 3714 3715 3716 3718 3719 3721 3723 3724 3726 3729
3731 3732 3734 3736 3739 3741 3743 3745 3747 3748 3750
3753 3755 3756 3758 3760 3762 3765 3767 3769 3771 3773
3775 3776 3777 3778 3780 3781 3782 3783 3785 3786 3787
3789 3791 3793 3795 3797 3798 3800 3802 3804 3805 3807
3809 3811 3812 3813 3815 3817 3819 3823 3825 3827 3829
3831 3833 3835 3837 3840 3843 3846 3848 3850 3852 3855
3857 3859 3861 3863 3866 3868 3870 3871 3873 3875 3877
3880 3882 3883 3885 3887 3889 3891 3894 3896 3898 3900
3902 3904 3906 3907 3908 3909 3910 3912 3913 3915 3919
3921 3922 3923 3925 3927 3929 3931 3933 3935 3937 3939
3941 3943 3945 3946 3947 3949 3952 3953 3954 3956 3959
3961 3963 3965 3967 3968 3971 3972 3974 3975 3976 3978
3979 3980 3984 3986 3988 3990 3991 3992 3995 3997 3999
4001 4003 4006 4008 4010 4011 4012 4013 4014 4015 4017
4019 4021 4023 4026 4027 4028 4030 4032 4033 4034 4035
4037 4043 4046 4049 4051 4053 4055 4057 4059 4061 4063
4064 4065 4066 4068 4070 4072 4075 4077 4079 4081 4083
4084 4086 4088 4090 4092 4093 4094 4095 4097 4098 4100
4101 4102 4104 4105 4106 4108 4109 4110 4111 4113 4115
4117 4118 4119 4120 4122 4124 4126 4128 4130 4133 4135
4137 4139 4140 4143 4144 4145 4146 4147 4149 4150 4152
4153 4154 4156 4157 4158 4159 4160 4161 4162 4165 4167
4168 4170 4172 4174 4175 4176 4179 4181 4183 4185 4186
4187 4188 4190 4191 4193 4195 4196 4197 4199 4201 4202
4203 4205 4206 4207 4208 4210 4212 4214 4216 4218 4219
4220 4223 4225 4226 4231 4232 4233 4234 4235 4236 4237
4238 4239 4240 4241 4242 4243 4244 4246 4247 4248 4249
4250 4252 4253 4255 4260 4261 4263 4264 4265 4267 4269
4270 4272 4273 4276 4278 4279 4281 4284 4286 4288 4289
4290 4291 4293 4294 4295 4296 4297 4298 4300 4302 4304
4305 4306 4307 4308 4309 4310 4312 4314 4316 4317 4320
4321 4322 4323 4324 4325 4326 4328 4329 4331 4333 4335
4337 4339 4340 4342 4344 4345 4346 4347 4348 4349 4350
4351 4354 4355 4357 4359 4361 4362 4363 4364 4365 4366
4367 4368 4370 4371 4372 4373 4375 4376 4378 4379 4381
4383 4384 4386 4388 4390 4391 4392 4393 4394 4395 4396
4397 4398 4399 4400 4401 4402 4404 4405 4407 4408 4409
4411 4412 4413 4414 4415 4417 4419 4421 4423 4424 4426
4429 4431 4432 4433 4435 4436 4438 4439 4440 4441 4442
4443 4445 4446 4447 4448 4449 4453 4454 4456 4457 4458
4459 4462 4463 4464 4465 4468 4469 4471 4473 4474 4475
4476 4477 4478 4479 4480 4481 4482 4483 4484 4485 4486
4487 4488 4489 4490 4491 4492 4493 4496 4498 4499 4501
4502 4504 4505 4506 4507 4508 4509 4510 4512 4513 4514
4515 4516 4517 4518 4519 4520 4521 4523 4524 4525 4526
4528 4531 4532 4533 4535 4536 4537 4539 4540 4541 4543
4544 4546 4547 4548 4549 4550 4551 4552 4553 4554 4555
4556 4557 4558 4559 4561 4562 4564 4565 4566 4567 4568
MSN CONFIGURATION
4569 4571 4572 4573 4574 4575 4576 4578 4579 4580 4581 001
4582 4584 4586 4587 4588 4589 4591 4592 4593 4594 4595
4596 4597 4599 4600 4601 4602 4603 4604 4606 4608 4609
4610 4612 4613 4614 4615 4616 4618 4619 4620 4621 4623
4625 4627 4628 4630 4631 4632 4633 4634 4636 4637 4639
4641 4642 4644 4645 4646 4647 4649 4651 4652 4653 4655
4656 4657 4658 4659 4661 4664 4666 4668 4670 4671 4673
4674 4675 4676 4677 4678 4680 4681 4683 4684 4685 4686
4687 4688 4689 4690 4692 4694 4696 4697 4699 4700 4701
4702 4704 4707 4708 4709 4711 4712 4714 4715 4716 4718
4720 4721 4722 4723 4724 4725 4726 4727 4729 4730 4733
4735 4736 4738 4739 4740 4741 4742 4743 4745 4747 4748
4749 4750 4751 4752 4754 4757 4758 4760 4762 4763 4765
4767 4769 4770 4772 4775 4776 4777 4780 4782 4784 4786
4789 4791 4793 4794 4795 4797 4798 4799 4800 4802 4803
4804 4805 4806 4807 4808 4809 4810 4812 4813 4814 4815
4816 4817 4818 4820 4821 4823 4825 4827 4828 4829 4831
4832 4833 4835 4836 4839 4840 4844 4845 4848 4849 4851
4852 4853 4854 4855 4857 4858 4860 4861 4862 4864 4865
4866 4867 4868 4869 4870 4872 4874 4876 4877 4879 4880
4882 4883 4884 4886 4887 4888 4889 4890 4891 4892 4894
4895 4896 4897 4899 4900 4902 4903 4904 4905 4906 4907
4908 4909 4911 4912 4913 4914 4915 4917 4918 4919 4920
4921 4922 4924 4926 4927 4928 4929 4930 4931 4933 4934
4936 4937 4938 4939 4941 4942 4943 4944 4946 4947 4948
4950 4951 4952 4953 4954 4955 4958 4959 4961 4963 4964
4965 4967 4968 4969 4970 4972 4973 4974 4975 4977 4978
4979 4980 4981 4982 4983 4984 4985 4986 4987 4988 4989
4990 4991 4993 4996 4997 4999 5000 5001 5002 5003 5004
5006 5007 5008 5010 5011 5012 5013 5014 5015 5016 5017
5019 5020 5021 5022 5024 5026 5027 5029 5030 5031 5032
5033 5034 5036 5037 5039 5041 5042 5045 5046 5047 5048
5050 5051 5052 5053 5055 5056 5058 5060 5061 5062 5063
5064 5066 5067 5068 5069 5070 5071 5072 5073 5075 5076
5078 5080 5081 5082 5084 5086 5089 5090 5091 5092 5093
5094 5095 5096 5100 5101 5102 5103 5104 5106 5107 5108
5109 5110 5111 5112 5113 5114 5115 5116 5117 5120 5121
5122 5123 5125 5127 5128 5129 5131 5132 5134 5135 5136
5137 5138 5139 5140 5141 5142 5143 5144 5145 5146 5147
5148 5149 5150 5151 5152 5153 5155 5156 5158 5159 5161
5162 5163 5165 5166 5167 5168 5170 5171 5172 5174 5175
5176 5178 5179 5181 5183 5184 5185 5187 5188 5189 5190
5191 5194 5195 5196 5198 5200 5201 5202 5203 5204 5206
5207 5209 5211 5212 5213 5214 5215 5216 5217 5218
MSN CONFIGURATION
2476 2553 2590 2610 2653 2687 2707 2713 2730 2736 2741 002
2756 2759 2767 2793 2799 2809 2823 2862 2868 2882 2895
2903 2912 2916 2919 2927 2933 2936 2957 2965 2971 2974
2996 2999 3005 3013 3015 3022 3034 3051 3067 3075 3081
3098 3112 3120 3126 3130 3146 3191 3198 3207 3212 3217
3222 3229 3233 3235 3241 3247 3249 3251 3254 3262 3265
3267 3274 3283 3290 3294 3297 3302 3307 3315 3322 3326
3329 3334 3339 3340 3350 3355 3360 3367 3369 3372 3382
3387 3397 3399 3401 3405 3419 3429 3434 3441 3458 3459
3462 3471 3493 3498 3504 3507 3512 3522 3523 3525 3527
3539 3546 3552 3557 3566 3573 3575 3583 3584 3587 3592
3593 3600 3612 3619 3623 3625 3629 3633 3636 3637 3639
3645 3653 3655 3665 3669 3673 3678 3681 3682 3688 3708
3712 3717 3722 3725 3730 3737 3738 3740 3749 3752 3761
3764 3766 3784 3792 3796 3806 3814 3816 3820 3830 3847
3858 3862 3864 3867 3869 3878 3879 3881 3884 3893 3899
3916 3920 3924 3926 3928 3930 3934 3936 3938 3940 3944
3948 3951 3955 3960 3964 3966 3969 3973 3977 3981 3987
3989 3993 3996 4002 4005 4009 4016 4022 4025 4031 4041
4044 4045 4047 4050 4054 4058 4062 4067 4073 4074 4078
4082 4085 4091 4096 4099 4103 4107 4112 4116 4123 4131
4134 4136 4138 4142 4148 4155 4173 4180 4184 4189 4194
4198 4209 4213 4217 4221 4224 4230 4251 4266 4271 4274
4277 4280 4283 4292 4299 4311 4315 4318 4334 4338 4341
4352 4358 4360 4369 4374 4377 4382 4387 4406 4416 4420
4430 4461 4467 4472 4494 4500 4530 4534 4538 4542 4545
4560 4570 4577 4585 4590 4607 4611 4617 4626 4638 4643
4648 4654 4662 4669 4672 4682 4698 4703 4706 4710 4719
4728 4731 4737 4746 4753 4761 4771 4779 4783 4788 4792
4811 4819 4824 4826 4830 4834 4838 4843 4847 4850 4856
4863 4873 4881 4885 4893 4898 4901 4916 4923 4925 4932
4935 4940 4945 4949 4957 4960 4962 4966 4971 4976 4994
5009 5025 5028 5035 5038 5044 5049 5054 5059 5065 5074
5077 5083 5087 5099 5118 5124 5126 5133 5154 5160 5164
5169 5173 5177 5180 5186 5192 5197 5199 5205 5210 5227
5233 5235 5237 5241 5244 5247 5251 5254 5257
3917 4177 4178 4229 4245 4257 4303 4343 4356 4434 4460 004
4466 4495 4497 4527
**CONF 001
Config. 001 is valid for A320 aircraft on which:
- Mod. No. 30948P6972 (or Service Bulletin No. A320-92-1021) is embodied.
- Mod. No. 30626K6443 is embodied.
- Mod. No. 30027P6972 is not embodied.
- Mod. No. 35481P9181 is not embodied.
- Mod. No. 35482P9182 is not embodied.
- Mod. No. 35483P9183 is not embodied.
**CONF 002
Config. 002 is valid for A321 aircraft on which:
- Mod. No. 30948P6972 (or Service Bulletin No. A320-92-1021) is embodied.
- Mod. No. 30626K6443 is embodied.
- Mod. No. 30027P6972 is not embodied.
- Mod. No. 35481P9181 is not embodied.
- Mod. No. 35482P9182 is not embodied.
- Mod. No. 35483P9183 is not embodied.
**CONF 003
Config. 003 is valid for A319 aircraft on which:
- Mod. No. 30948P6972 (or Service Bulletin No. A320-92-1021) is embodied.
- Mod. No. 30626K6443 is embodied.
- Mod. No. 30027P6972 is not embodied.
- Mod. No. 35481P9181 is not embodied.
- Mod. No. 35482P9182 is not embodied.
- Mod. No. 35483P9183 is not embodied.
or A318 aircraft on which:
- Mod. No. 30948P6972 (or Service Bulletin No. A320-92-1021) is not embodied.
- Mod. No. 30626K6443 is embodied.
- Mod. No. 30027P6972 is embodied.
- Mod. No. 35481P9181 is not embodied.
- Mod. No. 35482P9182 is not embodied.
- Mod. No. 35483P9183 is not embodied.
**CONF 004
Config 004 is valid for A320 aircraft on which
- Mod. No. 30948P6972 (or Service Bulletin No. A320-92-1021) is embodied.
- Mod. No. 30626K6443 is embodied.
- Mod. No. 30027P6972 is not embodied.
- Mod. No. 35481P9181 is not embodied.
- Mod. No. 35482P9182 is not embodied.
- Mod. No. 35483P9183 is not embodied.
- Mod No. 151801P12216 is not embodied.
**CONF 002
**CONF 003
**CONF ALL
B. CONCURRENT REQUIREMENTS
None
C. REASON
(1) History
Experiences have shown that the sensors for monitoring the landing gear and the aft
cargo door give indications that do not agree with each other. This behavior is caused
by an Electro Magnetic Interference (EMI) effect across the sensor cables.
(2) Objective/Action
This Service Bulletin gives the necessary instructions to remove and install a new
shielded cable from:
- Connector 241VC to connector 1943VC to prevent the EMI effect on sensors 32WV
and 34WV.
(3) Advantages
The accomplishment of this Service Bulletin will increase the operational reliability of the
related sensors.
None
D. DESCRIPTION
**CONF 001
(1) Modify the Wiring between the Avionics Compartment and the Cargo Compartment.
**CONF 002
(1) Modify the Wiring between the Avionics Compartment and the Cargo Compartment.
**CONF 003
(1) Modify the Wiring between the Avionics Compartment and the Cargo Compartment.
**CONF 004
(1) Modify the Wiring between the Avionics Compartment and the Cargo Compartment.
**CONF ALL
E. COMPLIANCE
(1) Classification
F. APPROVAL
The technical content of this document is approved under the authority of Design
Organisation Approval No. EASA.21J.031.
If an aircraft listed in the effectivity has a modification or repair embodied that is not of
AIRBUS origin, and which affects the content of this Service Bulletin, the operator is
responsible for obtaining approval by its airworthiness authority for any adaptation necessary
before incorporation of the Service Bulletin.
G. MANPOWER
The manpower estimates given in this Service Bulletin are based on the direct labor cost to
do the work. These estimates assume that the work will be done by experienced personnel,
and may need to be revised upwards to suit operator’s circumstances. The estimates do not
include the time to prepare, plan or inspect the work. Manufacture and procurement of parts
and tools, drying times for paints, sealants, etc., and general administration work are also not
included.
**CONF 001
NOTE: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAB given in Appendix 01 - Manpower Gantt Chart .
**CONF 002
NOTE: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAB given in Appendix 01 - Manpower Gantt Chart .
**CONF 003
NOTE: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAB given in Appendix 01 - Manpower Gantt Chart .
**CONF 004
NOTE: For an explanation of the man-hours and elapsed time, refer to the Gantt
Chart, Fig. A-FAAAB given in Appendix 01 - Manpower Gantt Chart .
**CONF ALL
Not Changed
Not Changed
J. REFERENCES
**CONF 001
**CONF 002
**CONF 003
**CONF 004
**CONF ALL
K. PUBLICATION AFFECTED
L. INTERCHANGEABILITY/MIXABILITY
Not Applicable
M. SPARES
None
2. MATERIAL INFORMATION
**CONF ALL
Customers with aircraft shown in the effectivity of this Service Bulletin should send a
purchase order to AIRBUS. Quote the number of this Service Bulletin. The address is:
Kit 211208A01R04
Cost 2,550.00 USD
Availability 120 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AIRBUS Spares portal or through a request for quotation to [email protected].
Kit 211208A02R04
Cost 2,570.00 USD
Availability 120 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AIRBUS Spares portal or through a request for quotation to [email protected].
Kit 211208A03R04
Cost 2,550.00 USD
Availability 120 calendar days from receipt of order
The availability given above is the standard lead time from the date of your purchase
order. If items are required before this time, please include a retrofit planning schedule
with your order so that we can try to comply with your requirements.
The sales terms (costs and availability) are estimated in relation to economic conditions.
The latest valid price and lead time for ordering purposes shall be obtained through the
AIRBUS Spares portal or through a request for quotation to [email protected].
As a special policy applied to this Service Bulletin, AIRBUS will provide a 15% reduction to
the applicable kits sales prices given in the paragraph Price and Availability for orders placed
before Dec 31/18.
C. LIST OF COMPONENTS
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
1 NAS1149F0332P 5 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
5 NAS1801-3-9 1 SCREW
6 D9241759800000 1 PLATE
7 NAS1149C0332R 6 WASHER
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
D9000095225695 1 BUNDLE
D9100095214495 1 SET
NSA935401-03 TIE
NSA935401-05 TIE
NSA935401-08 TIE
NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
Kit 211208A02R04
ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
1 NAS1149F0332P 8 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
5 NAS1801-3-9 1 SCREW
6 D9241763400000 1 PLATE
8 NAS1801-3-11 1 SCREW
ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
9 NSA5516-02ND 1 CLAMP
D9000095225695 1 BUNDLE
D9100095214495 1 SET
NSA935401-03 TIE
NSA935401-05 TIE
NSA935401-08 TIE
NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
Kit 211208A03R04
ITEM NEW PART N˚ QTY (UM) KEYWORD ITEM OLD PART N˚ INT SEE
NOTES
1 NAS1149F0332P 8 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
5 NAS1801-3-9 1 SCREW
6 D9241764000000 1 PLATE
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
D9000095225695 1 BUNDLE
D9100095214495 1 SET
NSA935401-03 TIE
NSA935401-05 TIE
NSA935401-08 TIE
NOTE: If you find part numbers of hardware components in the related kit(s) which
you cannot identify in the LIST OF COMPONENTS of this Service Bulletin,
refer to Standards Manual (SM). The SM will give you the correct part number
to part number relationship.
None
None
F. TOOLING
None
3. ACCOMPLISHMENT INSTRUCTIONS
WARNING: MAKE SURE THAT YOU OBEY ALL THE WARNINGS AND ALL THE CAUTIONS
INCLUDED IN THE REFERENCED PROCEDURES.
NOTE: The accomplishment instructions of this Service Bulletin include procedures given
in other documents or in other sections of the Service Bulletin. When the words
’refer to’ are used and the operator has a procedure accepted by the local authority
he belongs to, the accepted alternative procedure can be used. When the words ’in
accordance with’ are used then the given procedure must be followed.
NOTE: The access and close-up instructions, not comprising return to service tests, in this
Service Bulletin do not constitute or affect the technical intent of the Service
Bulletin. Operators can therefore, as deemed necessary, omit or add access and/or
close-up steps to add flexibility to their maintenance operations as long as the
technical intent of the Service Bulletin is met within the set parameters.
NOTE: Manual titles given in the accomplishment instructions are referred to by acronyms.
Refer to paragraph 1.J., References, for the definition of acronyms.
NOTE: This Service Bulletin contains the instructions for the on-aircraft maintenance
necessary to ensure the continued airworthiness of the aircraft.
For any deviations to the instructions contained herein, contact AIRBUS for further
instructions and approval.
**CONF 001
Zone
120 130
From 120 to 130
Modified FIN
2208VN 3311VN
Access
Door 811 812 822 824 825
Manpower
TOTAL MANHOURS 28.00
ELAPSED TIME (HOURS) 23.50
**CONF 002
Zone
120 130
From 120 to 130
Modified FIN
2208VN 3311VN
Access
Door 811 812 822 824 825
Manpower
TOTAL MANHOURS 28.00
ELAPSED TIME (HOURS) 23.50
**CONF 003
Zone
120 130
From 120 to 130
Modified FIN
2208VN 3311VN
Access
Door 811 812 822 824 825
Manpower
TOTAL MANHOURS 28.00
ELAPSED TIME (HOURS) 23.50
**CONF 004
Zone
120 130
From 120 to 130
Modified FIN
2208VN 3311VN
Access
Door 811 812 822 824 825
Manpower
TOTAL MANHOURS 28.00
ELAPSED TIME (HOURS) 23.50
**CONF ALL
A. GENERAL
**CONF 001
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-001
Task 20-21-15-912-001
Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-33-00
20-33-44
20-51-20
20-52-21
20-56-51
Structural Repair Manual (SRM) 51-42-00
51-43-00
51-44-00
51-47-00
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag the parts you must remove and retain to make the subsequent installation
easier.
(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(f) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-001.
(g) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.
(i) Get fasteners spacing and margin data in accordance with SRM 51-47-00.
(j) Get alternative and substitute fasteners data in accordance with SRM 51-43-00.
(k) Get fastener hole diameters and drill data in accordance with SRM 51-44-00.
(l) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
(m) For the general installation of electrical wire harnesses, refer to ESPM 20-33-00.
(n) Make sure that the electrical connectors are serviceable before you connect them
again.
(q) To install new wires, cut them to the necessary length, crimp the terminal and
connect them.
(r) Route the new wires with the wires that are in the aircraft.
(s) Use existing spare conduits to route wires in locations with difficult access.
(t) Do a continuity test of the new and/or modified wires, refer to ESPM 20-52-21.
(u) For the cable tie application and tooling, refer to ESPM 20-33-44 and ESPM
20-56-51.
(v) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
Manpower Resources
Skills NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 002
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-001
Task 20-21-15-912-001
Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-33-00
20-33-44
20-51-20
20-52-21
20-56-51
Structural Repair Manual (SRM) 51-42-00
51-43-00
51-44-00
51-47-00
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag the parts you must remove and retain to make the subsequent installation
easier.
(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(f) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-001.
(g) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.
(i) Get fasteners spacing and margin data in accordance with SRM 51-47-00.
(j) Get alternative and substitute fasteners data in accordance with SRM 51-43-00.
(k) Get fastener hole diameters and drill data in accordance with SRM 51-44-00.
(l) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
(m) For the general installation of electrical wire harnesses, refer to ESPM 20-33-00.
(n) Make sure that the electrical connectors are serviceable before you connect them
again.
(q) To install new wires, cut them to the necessary length, crimp the terminal and
connect them.
(r) Route the new wires with the wires that are in the aircraft.
(s) Use existing spare conduits to route wires in locations with difficult access.
(t) Do a continuity test of the new and/or modified wires, refer to ESPM 20-52-21.
(u) For the cable tie application and tooling, refer to ESPM 20-33-44 and ESPM
20-56-51.
(v) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
Manpower Resources
Skills NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 003
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-001
Task 20-21-15-912-001
Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-33-00
20-33-44
20-51-20
20-52-21
20-56-51
Structural Repair Manual (SRM) 51-42-00
51-43-00
51-44-00
51-47-00
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag the parts you must remove and retain to make the subsequent installation
easier.
(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(f) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-001.
(g) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.
(i) Get fasteners spacing and margin data in accordance with SRM 51-47-00.
(j) Get alternative and substitute fasteners data in accordance with SRM 51-43-00.
(k) Get fastener hole diameters and drill data in accordance with SRM 51-44-00.
(l) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
(m) For the general installation of electrical wire harnesses, refer to ESPM 20-33-00.
(n) Make sure that the electrical connectors are serviceable before you connect them
again.
(q) To install new wires, cut them to the necessary length, crimp the terminal and
connect them.
(r) Route the new wires with the wires that are in the aircraft.
(s) Use existing spare conduits to route wires in locations with difficult access.
(t) Do a continuity test of the new and/or modified wires, refer to ESPM 20-52-21.
(u) For the cable tie application and tooling, refer to ESPM 20-33-44 and ESPM
20-56-51.
(v) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
Manpower Resources
Skills NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF 004
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-20-00, Page Block 001
06-31-53, Page Block 001
06-41-53, Page Block 001
11-00-00, Page Block 201
Task 20-21-11-911-001
Task 20-21-15-912-001
Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-33-00
20-33-44
20-51-20
20-52-21
20-56-51
Structural Repair Manual (SRM) 51-42-00
51-43-00
51-44-00
51-47-00
(a) For the Frame (FR) identification, refer to AMM 06-31-53, Page Block 001.
(b) For the identification of zones, refer to AMM 06-20-00, Page Block 001.
(c) For the identification of access panels, refer to AMM 06-41-53, Page Block 001.
(d) Tag the parts you must remove and retain to make the subsequent installation
easier.
(e) Put all the retained hardware in identified plastic bags and attach the bags to the
related unit.
(f) To torque tighten the electrical component fasteners, refer to AMM Task
20-21-15-912-001.
(g) To torque tighten the standard threaded fasteners, refer to AMM Task
20-21-11-911-001.
(i) Get fasteners spacing and margin data in accordance with SRM 51-47-00.
(j) Get alternative and substitute fasteners data in accordance with SRM 51-43-00.
(k) Get fastener hole diameters and drill data in accordance with SRM 51-44-00.
(l) For the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
(m) For the general installation of electrical wire harnesses, refer to ESPM 20-33-00.
(n) Make sure that the electrical connectors are serviceable before you connect them
again.
(q) To install new wires, cut them to the necessary length, crimp the terminal and
connect them.
(r) Route the new wires with the wires that are in the aircraft.
(s) Use existing spare conduits to route wires in locations with difficult access.
(t) Do a continuity test of the new and/or modified wires, refer to ESPM 20-52-21.
(u) For the cable tie application and tooling, refer to ESPM 20-33-44 and ESPM
20-56-51.
(v) For the installation of placards, refer to AMM 11-00-00, Page Block 201.
Manpower Resources
Skills NON SPECIFIC
Write in the applicable aircraft records that you have done all the work given in this
Service Bulletin.
**CONF ALL
B. PREPARATION
**CONF 001
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-41-53, Page Block 001
Task 12-34-24-869-002
Task 24-38-51-000-001
Task 25-54-11-000-001
Task 25-54-12-000-001
Task 25-54-12-000-002
Task 52-10-00-010-001
Task 52-30-00-860-001
Task 52-30-00-860-003
Task 52-30-00-860-005
Task 52-41-00-010-002
NOTE: For the basic Aircraft configuration, refer to AMM Chapter ’Introduction -
Aircraft status for maintenance’ in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-002.
(b) Put the access platforms in position at doors 825, 831 or 841, 811, 812, 822 and
824.
(c) Open the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-001 or AMM Task 52-30-00-860-003 or AMM Task
52-30-00-860-005.
(d) Open the FWD Passenger/Crew door 831 or 841, refer to AMM Task
52-10-00-010-001.
(e) Open the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-010-002.
(f) Remove all the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-000-002.
(g) Remove the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-000-001 and AMM 06-41-53, Page
Block 001.
(h) Remove all the necessary partition panels, refer to AMM Task 25-54-12-000-001.
(i) If installed, remove from the modified plate the connectors No. 1939VC, 1941VC,
1943VC, 1945VC, 1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC,
1961VC, 1963VC, 1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC,
1979VC, 1981VC, 1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and
1999VC without disconnection of the wires.
(j) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(k) Make sure that there is (are) warning notice(s) on external power receptacle to tell
persons not to connect an external power source.
(l) Make sure that the EMER EXIT LT pushbutton switch on 25VU is on OFF position.
(m) In the cockpit, on the overhead panel 35VU release BAT pushbutton switches.
(n) Put a warning notice on panel 35VU to tell persons not to operate the batteries.
(o) Put a warning notice on refuel/defuel panel 800VU to tell persons not to operate the
NORMAL BATTERY switch.
(p) Put a warning notice in the cockpit to tell persons not to start the APU.
(q) Put a warning notice in the cockpit to tell persons not to start the ENG1,2.
- For Job Set-up, refer to the removal of the Batteries, refer to AMM Task
24-38-51-000-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 21-31-34-000-001
Task 21-43-34-000-002
Task 21-61-34-000-001
Task 24-22-33-000-001
Task 34-36-31-000-001
Task 36-11-34-000-001
1 Remove and retain the cabin pressure controller (FIN 11HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the air conditioning controller (FIN 47HH) (if installed),
refer to AMM Task 21-61-34-000-001.
3 Remove and retain the electrical generation interface unit (FIN 22XU1) (if
installed), refer to AMM Task 24-22-33-000-001.
4 Remove and retain the multi-mode receiver (FIN 40RT1) (if installed), refer to
AMM Task 34-36-31-000-001.
5 Remove and retain the instrument landing system receiver (FIN 2RT1) (if
installed), refer to AMM Task 34-36-31-000-001.
6 Remove and retain the bleed monitoring computer (FIN 1HA1) (if installed),
refer to AMM Task 36-11-34-000-001.
8 Disconnect the bonding strap and remove the shelf from the aircraft.
1 Remove and retain the cabin pressure controller (FIN 12HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the heat controller (FIN 10HC) (if installed), refer to AMM
Task 21-43-34-000-002.
3 Remove and retain the air conditioning controller (FIN 57HH) (if installed),
refer to AMM Task 21-61-34-000-001.
4 Remove and retain the electrical generation interface unit (FIN 22XU2), refer
to AMM Task 24-22-33-000-001.
5 Remove and retain the multi-mode receiver (FIN 40RT2) (if installed), refer to
AMM Task 34-36-31-000-001.
6 Remove and retain the instrument landing system receiver (FIN 2RT2) (if
installed), refer to AMM Task 34-36-31-000-001.
7 Remove and retain the bleed monitoring computer (FIN 1HA2) (if installed),
refer to AMM Task 36-11-34-000-001.
9 Disconnect the bonding strap and remove the shelf from the aircraft.
**CONF 002
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-41-53, Page Block 001
Task 12-34-24-869-002
Task 24-38-51-000-001
Task 25-54-11-000-001
Task 25-54-12-000-001
Task 25-54-12-000-002
Task 52-10-00-010-001
Task 52-30-00-860-001
Task 52-30-00-860-003
Task 52-30-00-860-005
Task 52-41-00-010-002
NOTE: For the basic Aircraft configuration, refer to AMM Chapter ’Introduction -
Aircraft status for maintenance’ in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-002.
(b) Put the access platforms in position at doors 825, 831 or 841, 811, 812, 822 and
824.
(c) Open the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-001 or AMM Task 52-30-00-860-003 or AMM Task
52-30-00-860-005.
(d) Open the FWD Passenger/Crew door 831 or 841, refer to AMM Task
52-10-00-010-001.
(e) Open the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-010-002.
(f) Remove all the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-000-002.
(g) Remove the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-000-001 and AMM 06-41-53, Page
Block 001.
(h) Remove all the necessary partition panels, refer to AMM Task 25-54-12-000-001.
(i) If installed, remove from the modified plate the connectors No. 1939VC, 1941VC,
1943VC, 1945VC, 1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC,
1961VC, 1963VC, 1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC,
1979VC, 1981VC, 1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and
1999VC without disconnection of the wires.
(j) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(k) Make sure that there is (are) warning notice(s) on external power receptacle to tell
persons not to connect an external power source.
(l) Make sure that the EMER EXIT LT pushbutton switch on 25VU is on OFF position.
(m) In the cockpit, on the overhead panel 35VU release BAT pushbutton switches.
(n) Put a warning notice on panel 35VU to tell persons not to operate the batteries.
(o) Put a warning notice on refuel/defuel panel 800VU to tell persons not to operate the
NORMAL BATTERY switch.
(p) Put a warning notice in the cockpit to tell persons not to start the APU.
(q) Put a warning notice in the cockpit to tell persons not to start the ENG1,2.
- For Job Set-up, refer to the removal of the Batteries, refer to AMM Task
24-38-51-000-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 21-31-34-000-001
Task 21-43-34-000-002
Task 21-61-34-000-001
Task 24-22-33-000-001
Task 34-36-31-000-001
Task 36-11-34-000-001
1 Remove and retain the cabin pressure controller (FIN 11HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the air conditioning controller (FIN 47HH) (if installed),
refer to AMM Task 21-61-34-000-001.
3 Remove and retain the electrical generation interface unit (FIN 22XU1) (if
installed), refer to AMM Task 24-22-33-000-001.
4 Remove and retain the multi-mode receiver (FIN 40RT1) (if installed), refer to
AMM Task 34-36-31-000-001.
5 Remove and retain the instrument landing system receiver (FIN 2RT1) (if
installed), refer to AMM Task 34-36-31-000-001.
6 Remove and retain the bleed monitoring computer (FIN 1HA1) (if installed),
refer to AMM Task 36-11-34-000-001.
8 Disconnect the bonding strap and remove the shelf from the aircraft.
1 Remove and retain the cabin pressure controller (FIN 12HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the heat controller (FIN 10HC) (if installed), refer to AMM
Task 21-43-34-000-002.
3 Remove and retain the air conditioning controller (FIN 57HH) (if installed),
refer to AMM Task 21-61-34-000-001.
4 Remove and retain the electrical generation interface unit (FIN 22XU2), refer
to AMM Task 24-22-33-000-001.
5 Remove and retain the multi-mode receiver (FIN 40RT2) (if installed), refer to
AMM Task 34-36-31-000-001.
6 Remove and retain the instrument landing system receiver (FIN 2RT2) (if
installed), refer to AMM Task 34-36-31-000-001.
7 Remove and retain the bleed monitoring computer (FIN 1HA2) (if installed),
refer to AMM Task 36-11-34-000-001.
9 Disconnect the bonding strap and remove the shelf from the aircraft.
**CONF 003
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-41-53, Page Block 001
Task 12-34-24-869-002
Task 24-38-51-000-001
Task 25-54-11-000-001
Task 25-54-12-000-001
Task 25-54-12-000-002
Task 52-10-00-010-001
Task 52-30-00-860-001
Task 52-30-00-860-003
Task 52-30-00-860-005
Task 52-41-00-010-002
NOTE: For the basic Aircraft configuration, refer to AMM Chapter ’Introduction -
Aircraft status for maintenance’ in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-002.
(b) Put the access platforms in position at doors 825, 831 or 841, 811, 812, 822 and
824.
(c) Open the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-001 or AMM Task 52-30-00-860-003 or AMM Task
52-30-00-860-005.
(d) Open the FWD Passenger/Crew door 831 or 841, refer to AMM Task
52-10-00-010-001.
(e) Open the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-010-002.
(f) Remove all the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-000-002.
(g) Remove the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-000-001 and AMM 06-41-53, Page
Block 001.
(h) Remove all the necessary partition panels, refer to AMM Task 25-54-12-000-001.
(i) If installed, remove from the modified plate the connectors No. 1939VC, 1941VC,
1943VC, 1945VC, 1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC,
1961VC, 1963VC, 1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC,
1979VC, 1981VC, 1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and
1999VC without disconnection of the wires.
(j) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(k) Make sure that there is (are) warning notice(s) on external power receptacle to tell
persons not to connect an external power source.
(l) Make sure that the EMER EXIT LT pushbutton switch on 25VU is on OFF position.
(m) In the cockpit, on the overhead panel 35VU release BAT pushbutton switches.
(n) Put a warning notice on panel 35VU to tell persons not to operate the batteries.
(o) Put a warning notice on refuel/defuel panel 800VU to tell persons not to operate the
NORMAL BATTERY switch.
(p) Put a warning notice in the cockpit to tell persons not to start the APU.
(q) Put a warning notice in the cockpit to tell persons not to start the ENG1,2.
- For Job Set-up, refer to the removal of the Batteries, refer to AMM Task
24-38-51-000-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 21-31-34-000-001
Task 21-43-34-000-002
Task 21-61-34-000-001
Task 24-22-33-000-001
Task 34-36-31-000-001
Task 36-11-34-000-001
1 Remove and retain the cabin pressure controller (FIN 11HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the air conditioning controller (FIN 47HH) (if installed),
refer to AMM Task 21-61-34-000-001.
3 Remove and retain the electrical generation interface unit (FIN 22XU1) (if
installed), refer to AMM Task 24-22-33-000-001.
4 Remove and retain the multi-mode receiver (FIN 40RT1) (if installed), refer to
AMM Task 34-36-31-000-001.
5 Remove and retain the instrument landing system receiver (FIN 2RT1) (if
installed), refer to AMM Task 34-36-31-000-001.
6 Remove and retain the bleed monitoring computer (FIN 1HA1) (if installed),
refer to AMM Task 36-11-34-000-001.
8 Disconnect the bonding strap and remove the shelf from the aircraft.
1 Remove and retain the cabin pressure controller (FIN 12HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the heat controller (FIN 10HC) (if installed), refer to AMM
Task 21-43-34-000-002.
3 Remove and retain the air conditioning controller (FIN 57HH) (if installed),
refer to AMM Task 21-61-34-000-001.
4 Remove and retain the electrical generation interface unit (FIN 22XU2), refer
to AMM Task 24-22-33-000-001.
5 Remove and retain the multi-mode receiver (FIN 40RT2) (if installed), refer to
AMM Task 34-36-31-000-001.
6 Remove and retain the instrument landing system receiver (FIN 2RT2) (if
installed), refer to AMM Task 34-36-31-000-001.
7 Remove and retain the bleed monitoring computer (FIN 1HA2) (if installed),
refer to AMM Task 36-11-34-000-001.
9 Disconnect the bonding strap and remove the shelf from the aircraft.
**CONF 004
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) 06-41-53, Page Block 001
Task 12-34-24-869-002
Task 24-38-51-000-001
Task 25-54-11-000-001
Task 25-54-12-000-001
Task 25-54-12-000-002
Task 52-10-00-010-001
Task 52-30-00-860-001
Task 52-30-00-860-003
Task 52-30-00-860-005
Task 52-41-00-010-002
NOTE: For the basic Aircraft configuration, refer to AMM Chapter ’Introduction -
Aircraft status for maintenance’ in Manual Front Matter section.
(a) Make sure that the aircraft is electrically grounded, refer to AMM Task
12-34-24-869-002.
(b) Put the access platforms in position at doors 825, 831 or 841, 811, 812, 822 and
824.
(c) Open the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-001 or AMM Task 52-30-00-860-003 or AMM Task
52-30-00-860-005.
(d) Open the FWD Passenger/Crew door 831 or 841, refer to AMM Task
52-10-00-010-001.
(e) Open the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-010-002.
(f) Remove all the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-000-002.
(g) Remove the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-000-001 and AMM 06-41-53, Page
Block 001.
(h) Remove all the necessary partition panels, refer to AMM Task 25-54-12-000-001.
(i) If installed, remove from the modified plate the connectors No. 1939VC, 1941VC,
1943VC, 1945VC, 1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC,
1961VC, 1963VC, 1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC,
1979VC, 1981VC, 1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and
1999VC without disconnection of the wires.
(j) Make sure that the external connector(s) is (are) not connected to the aircraft
receptacle(s) EXT PW.
(k) Make sure that there is (are) warning notice(s) on external power receptacle to tell
persons not to connect an external power source.
(l) Make sure that the EMER EXIT LT pushbutton switch on 25VU is on OFF position.
(m) In the cockpit, on the overhead panel 35VU release BAT pushbutton switches.
(n) Put a warning notice on panel 35VU to tell persons not to operate the batteries.
(o) Put a warning notice on refuel/defuel panel 800VU to tell persons not to operate the
NORMAL BATTERY switch.
(p) Put a warning notice in the cockpit to tell persons not to start the APU.
(q) Put a warning notice in the cockpit to tell persons not to start the ENG1,2.
- For Job Set-up, refer to the removal of the Batteries, refer to AMM Task
24-38-51-000-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 21-31-34-000-001
Task 21-43-34-000-002
Task 21-61-34-000-001
Task 24-22-33-000-001
Task 34-36-31-000-001
Task 36-11-34-000-001
1 Remove and retain the cabin pressure controller (FIN 11HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the air conditioning controller (FIN 47HH) (if installed),
refer to AMM Task 21-61-34-000-001.
3 Remove and retain the electrical generation interface unit (FIN 22XU1) (if
installed), refer to AMM Task 24-22-33-000-001.
4 Remove and retain the multi-mode receiver (FIN 40RT1) (if installed), refer to
AMM Task 34-36-31-000-001.
5 Remove and retain the instrument landing system receiver (FIN 2RT1) (if
installed), refer to AMM Task 34-36-31-000-001.
6 Remove and retain the bleed monitoring computer (FIN 1HA1) (if installed),
refer to AMM Task 36-11-34-000-001.
8 Disconnect the bonding strap and remove the shelf from the aircraft.
1 Remove and retain the cabin pressure controller (FIN 12HL) (if installed), refer
to AMM Task 21-31-34-000-001.
2 Remove and retain the heat controller (FIN 10HC) (if installed), refer to AMM
Task 21-43-34-000-002.
3 Remove and retain the air conditioning controller (FIN 57HH) (if installed),
refer to AMM Task 21-61-34-000-001.
4 Remove and retain the electrical generation interface unit (FIN 22XU2), refer
to AMM Task 24-22-33-000-001.
5 Remove and retain the multi-mode receiver (FIN 40RT2) (if installed), refer to
AMM Task 34-36-31-000-001.
6 Remove and retain the instrument landing system receiver (FIN 2RT2) (if
installed), refer to AMM Task 34-36-31-000-001.
7 Remove and retain the bleed monitoring computer (FIN 1HA2) (if installed),
refer to AMM Task 36-11-34-000-001.
9 Disconnect the bonding strap and remove the shelf from the aircraft.
**CONF ALL
C. PROCEDURE
**CONF 001
Manpower Resources
Manhours 10.00
Minimum number of person 2
Subtask elapsed time 7.00
Skills ELECTRICAL
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
D9000095225695 BUNDLE
NSA935401-03 265 TIE
NSA935401-05 265 TIE
NSA935401-08 265 TIE
References
Fig. A-FBAAA Sheet 01
Location of the Modification.
Fig. A-FWAAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(LH Side).
Fig. A-FWBAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(RH Side).
Fig. A-FHAAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (LH Side).
References
Fig. A-FHBAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (RH Side).
(a) Modify the connection of the wires as shown in the wiring diagrams Fig. A-FWAAA
Sheet 01 and Fig. A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
(b) Install the wires as shown in the wiring diagrams Fig. A-FWAAA Sheet 01 and Fig.
A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 3 WASHER
5 NAS1801-3-9 1 SCREW
6 D9241759800000 1 PLATE
7 NAS1149C0332R 6 WASHER
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Fig. A-FBDAA Sheet 01
Modification of the Plate in the Cargo Sheet 02
Compartment. Sheet 03
attached with:
attach with:
(c) Install the grounding point 3311VN with, refer to Fig. A-FBDAA Sheet 03:
(d) Attach the shielding wires with, refer to Fig. A-FBDAA Sheet 03:
(3) Subtask 211208-831-002-006 - Modify the Structure of the Electronics Rack 90VU.
Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 1.00
Skills AIRFRAME
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 2 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
D9100095214495 SET
NSA935401-03 1 TIE
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-44-00
Fig. A-FBBAA Sheet 01
Installation of the Grounding Point
2208VN
(a) Install the grounding point 2208VN, refer to Fig. A-FBBAA Sheet 01:
1 In the structure of the FWD Electronics Rack 90VU, drill the 2 holes to a
diameter of 5.2 mm (0.2047 in.).
3 Install:
attach with:
(b) Attach the shielding wire to the grounding point 2208VN with:
1 Tie-Cable NSA935401-03
**CONF 002
Manpower Resources
Manhours 10.00
Minimum number of person 2
Subtask elapsed time 7.00
Skills ELECTRICAL
Kit 211208A02R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
D9000095225695 BUNDLE
NSA935401-03 265 TIE
NSA935401-05 265 TIE
NSA935401-08 265 TIE
References
Fig. A-FBAAB Sheet 01
Location of the Modification.
Fig. A-FWAAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(LH Side).
Fig. A-FWBAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(RH Side).
Fig. A-FHAAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (LH Side).
Fig. A-FHBAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (RH Side).
(a) Modify the connection of the wires as shown in the wiring diagrams Fig. A-FWAAA
Sheet 01 and Fig. A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
(b) Install the wires as shown in the wiring diagrams Fig. A-FWAAA Sheet 01 and Fig.
A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC
Kit 211208A02R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 8 WASHER
5 NAS1801-3-9 1 SCREW
6 D9241763400000 1 PLATE
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Fig. A-FBDAB Sheet 01
Modification of the Plate in the Cargo Sheet 02
Compartment. Sheet 03
attach with:
(c) Install the grounding point 3311VN with, refer to Fig. A-FBDAB Sheet 03:
(d) Attach the shielding wires with, refer to Fig. A-FBDAB Sheet 03:
(3) Subtask 211208-831-002-005 - Modify the Structure of the Electronics Rack 90VU.
Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 1.00
Skills AIRFRAME
Kit 211208A02R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 2 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
D9100095214495 SET
NSA935401-03 1 TIE
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-44-00
Fig. A-FBBAA Sheet 01
Installation of the Grounding Point
2208VN
(a) Install the grounding point 2208VN, refer to Fig. A-FBBAA Sheet 01:
1 In the structure of the FWD Electronics Rack 90VU, drill the 2 holes to a
diameter of 5.2 mm (0.2047 in.).
3 Install:
attach with:
(b) Attach the shielding wire to the grounding point 2208VN with:
1 Tie-Cable NSA935401-03
**CONF 003
Manpower Resources
Manhours 10.00
Minimum number of person 2
Subtask elapsed time 7.00
Skills ELECTRICAL
Kit 211208A03R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
D9000095225695 BUNDLE
NSA935401-03 265 TIE
NSA935401-05 265 TIE
NSA935401-08 265 TIE
References
Fig. A-FBAAC Sheet 01
Location of the Modification.
Fig. A-FWAAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(LH Side).
Fig. A-FWBAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(RH Side).
References
Fig. A-FHAAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (LH Side).
Fig. A-FHBAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (RH Side).
(a) Remove the wires as shown in the wiring diagrams Fig. A-FWAAA Sheet 01 and
Fig. A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
(b) Install the wires as shown in the wiring diagrams Fig. A-FWAAA Sheet 01 and Fig.
A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC
Kit 211208A03R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 8 WASHER
5 NAS1801-3-9 1 SCREW
6 D9241764000000 1 PLATE
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Fig. A-FBDAC Sheet 01
Modification of the Plate in the Cargo Sheet 02
Compartment. Sheet 03
attached with:
attach with:
(c) Install the grounding point 3311VN with, refer to Fig. A-FBDAC Sheet 03:
(d) Attach the shielding wires with, refer to Fig. A-FBDAC Sheet 03:
(3) Subtask 211208-831-002-002 - Modify the Structure of the Electronics Rack 90VU.
Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 1.00
Skills AIRFRAME
Kit 211208A03R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 2 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
D9100095214495 SET
NSA935401-03 1 TIE
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-44-00
Fig. A-FBBAA Sheet 01
Installation of the Grounding Point
2208VN
(a) Install the grounding point 2208VN, refer to Fig. A-FBBAA Sheet 01:
1 In the structure of the FWD Electronics Rack 90VU, drill the 2 holes to a
diameter of 5.2 mm (0.2047 in.).
3 Install:
attach with:
(b) Attach the shielding wire to the grounding point 2208VN with:
1 Tie-Cable NSA935401-03
**CONF 004
Manpower Resources
Manhours 10.00
Minimum number of person 2
Subtask elapsed time 7.00
Skills ELECTRICAL
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
D9000095225695 BUNDLE
NSA935401-03 265 TIE
NSA935401-05 265 TIE
NSA935401-08 265 TIE
References
Fig. A-FBAAA Sheet 01
Location of the Modification.
Fig. A-FWAAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(LH Side).
Fig. A-FWBAA Sheet 01
Modification of the wiring between the
Avionics and the Cargo Compartment
(RH Side).
Fig. A-FHAAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (LH Side).
Fig. A-FHBAA Sheet 01
Hook-up Chart of the Modification of the
wiring between the Avionics and the
Cargo Compartment (RH Side).
(a) Modify the connection of the wires as shown in the wiring diagrams Fig. A-FWAAA
Sheet 01 and Fig. A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
(b) Install the wires as shown in the wiring diagrams Fig. A-FWAAA Sheet 01 and Fig.
A-FWBAA Sheet 01, and as described in the hook-up chart lines:
Bundle D9000095225695
Manpower Resources
Manhours 0.50
Minimum number of person 1
Subtask elapsed time 0.50
Skills NON SPECIFIC
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 3 WASHER
5 NAS1801-3-9 1 SCREW
6 D9241759800000 1 PLATE
7 NAS1149C0332R 6 WASHER
8 NAS1801-3-11 1 SCREW
9 NSA5516-02ND 1 CLAMP
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Fig. A-FBDAD Sheet 01
Modification of the Plate in the Cargo Sheet 02
Compartment. Sheet 03
attached with:
attach with
(c) Remove the placard 3309VN, Item (10), from the Plate, refer to Fig. A-FBDAD
Sheet 03:
(d) Install the grounding point 3311VN with refer to Fig. A-FBDAD Sheet 03:
(e) Attach the shielding wires, refer to Fig. A-FBDAD Sheet 03:
(3) Subtask 211208-831-002-006 - Modify the Structure of the Electronics Rack 90VU.
Manpower Resources
Manhours 1.00
Minimum number of person 1
Subtask elapsed time 1.00
Skills AIRFRAME
Kit 211208A01R04
ITEM NEW PART N˚ QTY (UM) KEYWORD SEE
NOTES
1 NAS1149F0332P 2 WASHER
2 NAS1801-3-8 2 SCREW
3 NSA5050-3 2 NUT
4 NSA935504-01 1 BRACKET
D9100095214495 SET
NSA935401-03 1 TIE
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Elec. Std. Practices Manual (ESPM) 20-51-20
Structural Repair Manual (SRM) 51-44-00
Fig. A-FBBAA Sheet 01
Installation of the Grounding Point
2208VN
(a) Install the grounding point 2208VN, refer to Fig. A-FBBAA Sheet 01:
1 In the structure of the FWD Electronics Rack 90VU, drill the 2 holes to a
diameter of 5.2 mm (0.2047 in.).
3 Install:
attach with:
(b) Attach the shielding wire to the grounding point 2208VN with:
1 Tie-Cable NSA935401-03
**CONF ALL
D. TEST
**CONF 001
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-720-005
Task 20-28-00-869-002
Task 21-21-00-710-001
Task 21-26-00-710-001
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-00-710-001
Task 21-61-34-400-002
Task 21-63-00-710-004
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 23-12-00-710-001
Task 24-22-33-400-002
Task 24-38-51-400-001
Task 24-41-00-861-002
Task 26-16-00-710-001
Task 28-28-00-710-003
Task 28-42-00-740-001
Task 28-46-00-710-001
Task 28-46-00-740-002
Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001
Task 34-36-31-400-001
Task 34-55-00-720-001
Task 36-11-34-400-001
Task 36-12-00-710-001
Task 47-31-34-740-001
Elec. Std. Practices Manual (ESPM) 20-52-10
- For Job Set-up, refer to the installation of the Batteries, refer to AMM Task
24-38-51-400-001.
- Make sure that the electrical connectors are clean and in correct condition.
(c) Energize the aircraft electrical circuits, refer to AMM Task 24-41-00-861-002.
NOTE: For the Maximum Permitted Resistance Values, refer to the table in
AMM Task 20-28-00-869-002.
NOTE: If the aircraft is operated in CAT 3 conditions, you must also do the
Land CAT 3 Capability Test, refer to AMM Task 22-97-00-710-001.
1 Do the operational test of the Instrument and Panel Integral Lighting, refer to
AMM Task 33-13-00-710-001.
4 Do the operational test of the Auto Flight System (AFS), refer to AMM Task
22-96-00-710-001.
7 Do the Ground Scanning of the Central Warning System, refer to AMM Task
31-50-00-710-001.
11 If connector 1949VC was removed, do the operational test of the APU Bleed
Air Supply and Crossbleed Systems, refer to AMM Task 36-12-00-710-001.
13 If connector 1957VC was removed, do the operational test of the ACT Fuel
Transfer-Pump Pressure Switch, refer to AMM Task 28-28-00-710-003.
14 If connector 1959VC or 1961VC was removed, do the BITE Test of the IGGS
without Bleed Air, refer to AMM Task 47-31-34-740-001.
(f) Procedure:
2 Do the test procedure as specified after the installation (if installed) of the aft
Cargo Heat Controller (FIN 10HC), refer to AMM Task 21-43-34-400-002.
3 Do the test procedure as specified after the installation (if installed) of the Air-
Conditioning System Controller (FIN 47HH and 57HH), refer to AMM Task
21-61-34-400-002.
4 Do the test procedure as specified after the installation (if installed) of the
Electrical Generation Interface Unit (EGIU)-1(2) (FIN 22XU1 and 22XU2), refer
to AMM Task 24-22-33-400-002.
6 Do the test procedure as specified after the installation (if installed) of the
Bleed Monitoring Computer (BMC) (FIN 1HA1 and 1HA2), refer to AMM Task
36-11-34-400-001.
7 Do the test procedure as specified after the installation (if installed) of the
Instrument Landing System (ILS) Receiver (FIN 2RT1 and 2RT2), refer to
AMM Task 34-36-31-400-001.
**CONF 002
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-720-005
Task 20-28-00-869-002
Task 21-21-00-710-001
Task 21-26-00-710-001
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-00-710-001
Task 21-61-34-400-002
Task 21-63-00-710-004
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 23-12-00-710-001
Task 24-22-33-400-002
Task 24-38-51-400-001
Task 24-41-00-861-002
Task 26-16-00-710-001
Task 28-28-00-710-003
Task 28-42-00-740-001
Task 28-46-00-710-001
Task 28-46-00-740-002
Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001
Task 34-36-31-400-001
Task 34-55-00-720-001
Task 36-11-34-400-001
Task 36-12-00-710-001
Task 47-31-34-740-001
Elec. Std. Practices Manual (ESPM) 20-52-10
- For Job Set-up, refer to the installation of the Batteries, refer to AMM Task
24-38-51-400-001.
- Make sure that the electrical connectors are clean and in correct condition.
(c) Energize the aircraft electrical circuits, refer to AMM Task 24-41-00-861-002.
NOTE: For the Maximum Permitted Resistance Values, refer to the table in
AMM Task 20-28-00-869-002.
NOTE: If the aircraft is operated in CAT 3 conditions, you must also do the
Land CAT 3 Capability Test, refer to AMM Task 22-97-00-710-001.
1 Do the operational test of the Instrument and Panel Integral Lighting, refer to
AMM Task 33-13-00-710-001.
4 Do the operational test of the Auto Flight System (AFS), refer to AMM Task
22-96-00-710-001.
7 Do the Ground Scanning of the Central Warning System, refer to AMM Task
31-50-00-710-001.
11 If connector 1949VC was removed, do the operational test of the APU Bleed
Air Supply and Crossbleed Systems, refer to AMM Task 36-12-00-710-001.
13 If connector 1957VC was removed, do the operational test of the ACT Fuel
Transfer-Pump Pressure Switch, refer to AMM Task 28-28-00-710-003.
14 If connector 1959VC or 1961VC was removed, do the BITE Test of the IGGS
without Bleed Air, refer to AMM Task 47-31-34-740-001.
(f) Procedure:
2 Do the test procedure as specified after the installation (if installed) of the aft
Cargo Heat Controller (FIN 10HC), refer to AMM Task 21-43-34-400-002.
3 Do the test procedure as specified after the installation (if installed) of the Air-
Conditioning System Controller (FIN 47HH and 57HH), refer to AMM Task
21-61-34-400-002.
4 Do the test procedure as specified after the installation (if installed) of the
Electrical Generation Interface Unit (EGIU)-1(2) (FIN 22XU1 and 22XU2), refer
to AMM Task 24-22-33-400-002.
6 Do the test procedure as specified after the installation (if installed) of the
Bleed Monitoring Computer (BMC) (FIN 1HA1 and 1HA2), refer to AMM Task
36-11-34-400-001.
7 Do the test procedure as specified after the installation (if installed) of the
Instrument Landing System (ILS) Receiver (FIN 2RT1 and 2RT2), refer to
AMM Task 34-36-31-400-001.
**CONF 003
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-720-005
Task 20-28-00-869-002
Task 21-21-00-710-001
Task 21-26-00-710-001
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-00-710-001
Task 21-61-34-400-002
Task 21-63-00-710-004
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 23-12-00-710-001
Task 24-22-33-400-002
Task 24-38-51-400-001
Task 24-41-00-861-002
Task 26-16-00-710-001
Task 28-28-00-710-003
Task 28-42-00-740-001
Task 28-46-00-710-001
Task 28-46-00-740-002
Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001
Task 34-36-31-400-001
Task 34-55-00-720-001
Task 36-11-34-400-001
Task 36-12-00-710-001
Task 47-31-34-740-001
Elec. Std. Practices Manual (ESPM) 20-52-10
- For Job Set-up, refer to the installation of the Batteries, refer to AMM Task
24-38-51-400-001.
- Make sure that the electrical connectors are clean and in correct condition.
(c) Energize the aircraft electrical circuits, refer to AMM Task 24-41-00-861-002.
NOTE: For the Maximum Permitted Resistance Values, refer to the table in
AMM Task 20-28-00-869-002.
NOTE: If the aircraft is operated in CAT 3 conditions, you must also do the
Land CAT 3 Capability Test, refer to AMM Task 22-97-00-710-001.
1 Do the operational test of the Instrument and Panel Integral Lighting, refer to
AMM Task 33-13-00-710-001.
4 Do the operational test of the Auto Flight System (AFS), refer to AMM Task
22-96-00-710-001.
7 Do the Ground Scanning of the Central Warning System, refer to AMM Task
31-50-00-710-001.
11 If connector 1949VC was removed, do the operational test of the APU Bleed
Air Supply and Crossbleed Systems, refer to AMM Task 36-12-00-710-001.
13 If connector 1957VC was removed, do the operational test of the ACT Fuel
Transfer-Pump Pressure Switch, refer to AMM Task 28-28-00-710-003.
14 If connector 1959VC or 1961VC was removed, do the BITE Test of the IGGS
without Bleed Air, refer to AMM Task 47-31-34-740-001.
(f) Procedure:
2 Do the test procedure as specified after the installation (if installed) of the aft
Cargo Heat Controller (FIN 10HC), refer to AMM Task 21-43-34-400-002.
3 Do the test procedure as specified after the installation (if installed) of the Air-
Conditioning System Controller (FIN 47HH and 57HH), refer to AMM Task
21-61-34-400-002.
4 Do the test procedure as specified after the installation (if installed) of the
Electrical Generation Interface Unit (EGIU)-1(2) (FIN 22XU1 and 22XU2), refer
to AMM Task 24-22-33-400-002.
6 Do the test procedure as specified after the installation (if installed) of the
Bleed Monitoring Computer (BMC) (FIN 1HA1 and 1HA2), refer to AMM Task
36-11-34-400-001.
7 Do the test procedure as specified after the installation (if installed) of the
Instrument Landing System (ILS) Receiver (FIN 2RT1 and 2RT2), refer to
AMM Task 34-36-31-400-001.
**CONF 004
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-720-005
Task 20-28-00-869-002
Task 21-21-00-710-001
Task 21-26-00-710-001
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-00-710-001
Task 21-61-34-400-002
Task 21-63-00-710-004
Task 22-96-00-710-001
Task 22-97-00-710-001
Task 23-12-00-710-001
Task 24-22-33-400-002
Task 24-38-51-400-001
Task 24-41-00-861-002
Task 26-16-00-710-001
Task 28-28-00-710-003
Task 28-42-00-740-001
Task 28-46-00-710-001
Task 28-46-00-740-002
Task 31-50-00-710-001
Task 31-50-00-710-004
Task 31-60-00-710-001
Task 33-13-00-710-001
Task 33-14-00-710-001
Task 34-36-31-400-001
Task 34-55-00-720-001
Task 36-11-34-400-001
Task 36-12-00-710-001
Task 47-31-34-740-001
Elec. Std. Practices Manual (ESPM) 20-52-10
- For Job Set-up, refer to the installation of the Batteries, refer to AMM Task
24-38-51-400-001.
- Make sure that the electrical connectors are clean and in correct condition.
(c) Energize the aircraft electrical circuits, refer to AMM Task 24-41-00-861-002.
NOTE: For the Maximum Permitted Resistance Values, refer to the table in
AMM Task 20-28-00-869-002.
NOTE: If the aircraft is operated in CAT 3 conditions, you must also do the
Land CAT 3 Capability Test, refer to AMM Task 22-97-00-710-001.
1 Do the operational test of the Instrument and Panel Integral Lighting, refer to
AMM Task 33-13-00-710-001.
4 Do the operational test of the Auto Flight System (AFS), refer to AMM Task
22-96-00-710-001.
7 Do the Ground Scanning of the Central Warning System, refer to AMM Task
31-50-00-710-001.
11 If connector 1949VC was removed, do the operational test of the APU Bleed
Air Supply and Crossbleed Systems, refer to AMM Task 36-12-00-710-001.
13 If connector 1957VC was removed, do the operational test of the ACT Fuel
Transfer-Pump Pressure Switch, refer to AMM Task 28-28-00-710-003.
14 If connector 1959VC or 1961VC was removed, do the BITE Test of the IGGS
without Bleed Air, refer to AMM Task 47-31-34-740-001.
(f) Procedure:
2 Do the test procedure as specified after the installation (if installed) of the aft
Cargo Heat Controller (FIN 10HC), refer to AMM Task 21-43-34-400-002.
3 Do the test procedure as specified after the installation (if installed) of the Air-
Conditioning System Controller (FIN 47HH and 57HH), refer to AMM Task
21-61-34-400-002.
4 Do the test procedure as specified after the installation (if installed) of the
Electrical Generation Interface Unit (EGIU)-1(2) (FIN 22XU1 and 22XU2), refer
to AMM Task 24-22-33-400-002.
6 Do the test procedure as specified after the installation (if installed) of the
Bleed Monitoring Computer (BMC) (FIN 1HA1 and 1HA2), refer to AMM Task
36-11-34-400-001.
7 Do the test procedure as specified after the installation (if installed) of the
Instrument Landing System (ILS) Receiver (FIN 2RT1 and 2RT2), refer to
AMM Task 34-36-31-400-001.
**CONF ALL
E. CLOSE-UP
**CONF 001
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-34-400-001
Task 24-22-33-400-002
Task 25-54-11-400-001
Task 25-54-12-400-001
Task 25-54-12-400-002
Task 34-36-31-400-001
Task 36-11-34-400-001
Elec. Std. Practices Manual (ESPM) 20-51-20
NOTE: Do the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
2 Install the cabin pressure controller (FIN 11HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the air conditioning controller (FIN 47HH) (if removed), refer to AMM
Task 21-61-34-400-001.
4 Install the EGIU (FIN 22XU1) (if removed), refer to AMM Task
24-22-33-400-002.
5 Install the multi-mode receiver (FIN 40RT1) (if removed), refer to AMM Task
34-36-31-400-001.
6 Install the ILS receiver (FIN 2RT1) (if installed), refer to AMM Task
34-36-31-400-001.
7 Install the BMC (FIN 1HA1) (if installed), refer to AMM Task
36-11-34-400-001.
8 Remove the protective caps and connect the shelf cut-off connectors.
2 Install the cabin pressure controller (FIN 12HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the heat controller (FIN 10HC) (if removed), refer to AMM Task
21-43-34-400-002.
4 Install the air conditioning controller (FIN 57HH) (if removed), refer to AMM
Task 21-61-34-400-001.
5 Install the EGIU (FIN 22XU2) (if removed), refer to AMM Task
24-22-33-400-002.
6 Install the multi-mode receiver (FIN 40RT2) (if removed), refer to AMM Task
34-36-31-400-001.
7 Install the ILS receiver (FIN 2RT2) (if installed), refer to AMM Task
34-36-31-400-001.
8 Install the BMC (FIN 1HA2) (if installed), refer to AMM Task
36-11-34-400-001.
9 Remove the protective caps and connect the shelf cut-off connectors.
(c) If removed, install the connectors No. 1939VC, 1941VC, 1943VC, 1945VC,
1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC, 1961VC, 1963VC,
1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC, 1979VC, 1981VC,
1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and 1999VC.
(d) Install the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-400-002.
(e) Install the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-400-001.
(f) If removed, install the partition panels, refer to AMM Task 25-54-12-400-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 52-10-00-410-001
Task 52-30-00-860-002
Task 52-30-00-860-004
Task 52-30-00-860-009
Task 52-41-00-410-002
(a) Close the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-002 or AMM Task 52-30-00-860-004 or AMM Task
52-30-00-860-009.
(b) Close the FWD Passenger/Crew 831 or 841, refer to AMM Task 52-10-00-410-001.
(c) Close the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-410-002.
(d) Restore the system and the aircraft to the normal operating condition.
(e) Make sure that the work areas are clean and clear of tools and other items of
equipment.
**CONF 002
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-34-400-001
Task 24-22-33-400-002
Task 25-54-11-400-001
Task 25-54-12-400-001
Task 25-54-12-400-002
Task 34-36-31-400-001
Task 36-11-34-400-001
Elec. Std. Practices Manual (ESPM) 20-51-20
NOTE: Do the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
2 Install the cabin pressure controller (FIN 11HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the air conditioning controller (FIN 47HH) (if removed), refer to AMM
Task 21-61-34-400-001.
4 Install the EGIU (FIN 22XU1) (if removed), refer to AMM Task
24-22-33-400-002.
5 Install the multi-mode receiver (FIN 40RT1) (if removed), refer to AMM Task
34-36-31-400-001.
6 Install the ILS receiver (FIN 2RT1) (if installed), refer to AMM Task
34-36-31-400-001.
7 Install the BMC (FIN 1HA1) (if installed), refer to AMM Task
36-11-34-400-001.
8 Remove the protective caps and connect the shelf cut-off connectors.
2 Install the cabin pressure controller (FIN 12HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the heat controller (FIN 10HC) (if removed), refer to AMM Task
21-43-34-400-002.
4 Install the air conditioning controller (FIN 57HH) (if removed), refer to AMM
Task 21-61-34-400-001.
5 Install the EGIU (FIN 22XU2) (if removed), refer to AMM Task
24-22-33-400-002.
6 Install the multi-mode receiver (FIN 40RT2) (if removed), refer to AMM Task
34-36-31-400-001.
7 Install the ILS receiver (FIN 2RT2) (if installed), refer to AMM Task
34-36-31-400-001.
8 Install the BMC (FIN 1HA2) (if installed), refer to AMM Task
36-11-34-400-001.
9 Remove the protective caps and connect the shelf cut-off connectors.
(c) If removed, install the connectors No. 1939VC, 1941VC, 1943VC, 1945VC,
1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC, 1961VC, 1963VC,
1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC, 1979VC, 1981VC,
1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and 1999VC.
(d) Install the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-400-002.
(e) Install the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-400-001.
(f) If removed, install the partition panels, refer to AMM Task 25-54-12-400-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 52-10-00-410-001
Task 52-30-00-860-002
Task 52-30-00-860-004
Task 52-30-00-860-009
Task 52-41-00-410-002
(a) Close the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-002 or AMM Task 52-30-00-860-004 or AMM Task
52-30-00-860-009.
(b) Close the FWD Passenger/Crew 831 or 841, refer to AMM Task 52-10-00-410-001.
(c) Close the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-410-002.
(d) Restore the system and the aircraft to the normal operating condition.
(e) Make sure that the work areas are clean and clear of tools and other items of
equipment.
**CONF 003
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-34-400-001
Task 24-22-33-400-002
Task 25-54-11-400-001
Task 25-54-12-400-001
Task 25-54-12-400-002
Task 34-36-31-400-001
Task 36-11-34-400-001
Elec. Std. Practices Manual (ESPM) 20-51-20
NOTE: Do the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
2 Install the cabin pressure controller (FIN 11HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the air conditioning controller (FIN 47HH) (if removed), refer to AMM
Task 21-61-34-400-001.
4 Install the EGIU (FIN 22XU1) (if removed), refer to AMM Task
24-22-33-400-002.
5 Install the multi-mode receiver (FIN 40RT1) (if removed), refer to AMM Task
34-36-31-400-001.
6 Install the ILS receiver (FIN 2RT1) (if installed), refer to AMM Task
34-36-31-400-001.
7 Install the BMC (FIN 1HA1) (if installed), refer to AMM Task
36-11-34-400-001.
8 Remove the protective caps and connect the shelf cut-off connectors.
2 Install the cabin pressure controller (FIN 12HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the heat controller (FIN 10HC) (if removed), refer to AMM Task
21-43-34-400-002.
4 Install the air conditioning controller (FIN 57HH) (if removed), refer to AMM
Task 21-61-34-400-001.
5 Install the EGIU (FIN 22XU2) (if removed), refer to AMM Task
24-22-33-400-002.
6 Install the multi-mode receiver (FIN 40RT2) (if removed), refer to AMM Task
34-36-31-400-001.
7 Install the ILS receiver (FIN 2RT2) (if installed), refer to AMM Task
34-36-31-400-001.
8 Install the BMC (FIN 1HA2) (if installed), refer to AMM Task
36-11-34-400-001.
9 Remove the protective caps and connect the shelf cut-off connectors.
(c) If removed, install the connectors No. 1939VC, 1941VC, 1943VC, 1945VC,
1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC, 1961VC, 1963VC,
1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC, 1979VC, 1981VC,
1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and 1999VC.
(d) Install the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-400-002.
(e) Install the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-400-001.
(f) If removed, install the partition panels, refer to AMM Task 25-54-12-400-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 52-10-00-410-001
Task 52-30-00-860-002
Task 52-30-00-860-004
Task 52-30-00-860-009
Task 52-41-00-410-002
(a) Close the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-002 or AMM Task 52-30-00-860-004 or AMM Task
52-30-00-860-009.
(b) Close the FWD Passenger/Crew 831 or 841, refer to AMM Task 52-10-00-410-001.
(c) Close the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-410-002.
(d) Restore the system and the aircraft to the normal operating condition.
(e) Make sure that the work areas are clean and clear of tools and other items of
equipment.
**CONF 004
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 20-28-00-912-004
Task 20-28-00-912-043
Task 21-31-34-400-001
Task 21-43-34-400-002
Task 21-61-34-400-001
Task 24-22-33-400-002
Task 25-54-11-400-001
Task 25-54-12-400-001
Task 25-54-12-400-002
Task 34-36-31-400-001
Task 36-11-34-400-001
Elec. Std. Practices Manual (ESPM) 20-51-20
NOTE: Do the electrical bonding, refer to ESPM 20-51-20 and AMM Task
20-28-00-912-004 or AMM Task 20-28-00-912-043.
2 Install the cabin pressure controller (FIN 11HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the air conditioning controller (FIN 47HH) (if removed), refer to AMM
Task 21-61-34-400-001.
4 Install the EGIU (FIN 22XU1) (if removed), refer to AMM Task
24-22-33-400-002.
5 Install the multi-mode receiver (FIN 40RT1) (if removed), refer to AMM Task
34-36-31-400-001.
6 Install the ILS receiver (FIN 2RT1) (if installed), refer to AMM Task
34-36-31-400-001.
7 Install the BMC (FIN 1HA1) (if installed), refer to AMM Task
36-11-34-400-001.
8 Remove the protective caps and connect the shelf cut-off connectors.
2 Install the cabin pressure controller (FIN 12HL) (if removed), refer to AMM
Task 21-31-34-400-001.
3 Install the heat controller (FIN 10HC) (if removed), refer to AMM Task
21-43-34-400-002.
4 Install the air conditioning controller (FIN 57HH) (if removed), refer to AMM
Task 21-61-34-400-001.
5 Install the EGIU (FIN 22XU2) (if removed), refer to AMM Task
24-22-33-400-002.
6 Install the multi-mode receiver (FIN 40RT2) (if removed), refer to AMM Task
34-36-31-400-001.
7 Install the ILS receiver (FIN 2RT2) (if installed), refer to AMM Task
34-36-31-400-001.
8 Install the BMC (FIN 1HA2) (if installed), refer to AMM Task
36-11-34-400-001.
9 Remove the protective caps and connect the shelf cut-off connectors.
(c) If removed, install the connectors No. 1939VC, 1941VC, 1943VC, 1945VC,
1947VC, 1949VC, 1951VC, 1953VC, 1955VC, 1957VC, 1959VC, 1961VC, 1963VC,
1965VC, 1967VC, 1969VC, 1971VC, 1973VC, 1975VC, 1977VC, 1979VC, 1981VC,
1983VC, 1985VC, 1987VC, 1989VC, 1991VC, 1997VC and 1999VC.
(d) Install the ceiling panels in the FWD cargo compartment, refer to AMM Task
25-54-12-400-002.
(e) Install the partition panels 131BW, 131AW and 132BW in the FWD cargo
compartment, refer to AMM Task 25-54-11-400-001.
(f) If removed, install the partition panels, refer to AMM Task 25-54-12-400-001.
Manpower Resources
Skills NON SPECIFIC
References
Aircraft Maintenance Manual (AMM) Task 52-10-00-410-001
Task 52-30-00-860-002
Task 52-30-00-860-004
Task 52-30-00-860-009
Task 52-41-00-410-002
(a) Close the FWD Cargo Compartment door 825, refer to AMM
Task 52-30-00-860-002 or AMM Task 52-30-00-860-004 or AMM Task
52-30-00-860-009.
(b) Close the FWD Passenger/Crew 831 or 841, refer to AMM Task 52-10-00-410-001.
(c) Close the Avionics Compartment doors 811, 812, 822 and 824, refer to AMM Task
52-41-00-410-002.
(d) Restore the system and the aircraft to the normal operating condition.
(e) Make sure that the work areas are clean and clear of tools and other items of
equipment.
3302VN
2M
FR35
1M
FR32
90VU
N_SB_211208_5_BAAA_01_01
**CONF 002
3302VN
FR35.6
2M
FR35.7
1M
90VU
N_SB_211208_5_BAAB_01_01
**CONF 003
3302VN
2M
1M
FR34
FR30
90VU
N_SB_211208_5_BAAC_01_01
**CONF ALL
FR1
1 2208VN
2
3 A
9 mm 90VU
02 (0.35 in)
1
2
45 mm
01 H1 (1.77 in)
TIE
CABLE 01 H2
TO 96VU
248VC−A (2M)
4
213.4 mm
(8.40 in)
=
=
B
NOTE:
01 DRILL HOLE TO A DIAMETER OF 5.2 mm (0.2047 in)
02 REMOVE THE SURFACE PROTECTION IN A DIAMETER
OF 14 mm (0.55 in) ON THE HIDDEN SIDE N_SB_211208_5_BBAA_01_02
**CONF 001
A C
FR35
FR32
BEFORE
B (6)
A
VIEW LOOKING FORWARD
FR33
(2) (7)
(2 POS) (4 POS)
(7) (8)
B
VIEW LOOKING DOWN N_SB_211208_5_BDAA_01_00
**CONF 001
AFTER
D 6
C
VIEW LOOKING FORWARD
FR33
E
(9) (2 POS) (4 POS) (9)
(2) 7
(2 POS) (4 POS)
7 (8)
D
VIEW LOOKING DOWN
N_SB_211208_5_BDAA_02_01
**CONF 001
3311VN 1
5
1
9 8
E
VIEW LOOKING AFT
N_SB_211208_5_BDAA_03_02
**CONF 002
A C
FR35.7
FR35.6
BEFORE
B (6)
A
VIEW LOOKING FORWARD
FR35.6
(3) (2 POS)
(4 POS) (3)
(1)
(2)
(2 POS) B (4 POS)
(1)
(2)
VIEW LOOKING DOWN
N_SB_211208_5_BDAB_01_00
**CONF 002
AFTER
D 6
C
VIEW LOOKING FORWARD
FR35.6
E
(3) (2 POS) (4 POS) (3)
1 1
(2 POS) (4 POS)
(2) (2)
D
VIEW LOOKING DOWN
N_SB_211208_5_BDAB_02_02
**CONF 002
3311VN 1
5
1
9 8
E
VIEW LOOKING AFT
N_SB_211208_5_BDAB_03_02
**CONF 003
A C
FR34
FR30
B (6)
A
VIEW LOOKING FORWARD
FR30
(3) (2 POS)
(4 POS) (9)
(1)
(2)
(2 POS) B (4 POS)
(1)
(2)
VIEW LOOKING DOWN
N_SB_211208_5_BDAC_01_00
**CONF 003
AFTER
D 6
C
VIEW LOOKING FORWARD
FR30
E
(3) (2 POS) (4 POS) (9)
1 1
(2 POS) (4 POS)
(2) (2)
D
VIEW LOOKING DOWN
N_SB_211208_5_BDAC_02_03
**CONF 003
3311VN 1
5
1
9 8
E
VIEW LOOKING AFT
N_SB_211208_5_BDAC_03_02
**CONF 004
A C
FR35
FR32
Z130
FR24
BEFORE
B (6)
A
VIEW LOOKING FORWARD
FR33
(2) (7)
(2 POS) (4 POS)
(7) (8)
B
VIEW LOOKING DOWN N_SB_211208_5_BDAD_01_00
**CONF 004
AFTER
D 6
C
VIEW LOOKING FORWARD
FR33
E
(9) (2 POS) (4 POS) (9)
(2) 7
(2 POS) (4 POS)
7 (8)
D
VIEW LOOKING DOWN
N_SB_211208_5_BDAD_02_00
**CONF 004
3311VN 1
5
1
9 8
(10)
3309VN
E
VIEW LOOKING AFT
N_SB_211208_5_BDAD_03_01
**CONF ALL
**CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Length Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 95VU 241VC−A 34 2161−0419 B 1M RF20 131 1943VC 28 M1O+M2O
2 95VU 241VC−A WS NSA936604CA0931 2161−0419 B 1M RF20 131 1943VC WS NSA936604CA0931 M1N+M2N
3 95VU 241VC−A 35 2161−0419 G 1M RF20 131 1943VC 27 M1O+M2O
4 95VU 241VC−A WS NSA936604CA0931 2161−0419 G 1M RF20 131 1943VC WS NSA936604CA0931 M1N+M2N
5 95VU 241VC−A 31 2161−0419 R 1M RF20 131 1943VC 29 M1O+M2O
6 95VU 241VC−A WS NSA936604CA0931 2161−0419 R 1M RF20 131 1943VC WS NSA936604CA0931 M1N+M2N
7 95VU 241VC−A 3 2161−0419 Y 1M RF20 131 1943VC 41 M1O+M2O
8 95VU 241VC−A WS NSA936604CA0931 2161−0419 Y 1M RF20 131 1943VC WS NSA936604CA0931 M1N+M2N
9
10
11
12 95VU 241VC−A SH 2161G7259 1M MLD20 26500 1060 131 1943VC SH (b) A
13 95VU 241VC−A 34 EN3155−015F2018 2161−7259 B 1M MLD20 26500 1060 131 1943VC 28 EN3155−015F2018 (b) A
14 95VU 241VC−A 35 EN3155−015F2018 2161−7259 G 1M MLD20 26500 1060 131 1943VC 27 EN3155−015F2018 (b) A
15 95VU 241VC−A 31 EN3155−015F2018 2161−7259 R 1M MLD20 26500 1060 131 1943VC 29 EN3155−015F2018 (b) A
16 95VU 241VC−A 3 EN3155−015F2018 2161−7259 Y 1M MLD20 26500 1060 131 1943VC 41 EN3155−015F2018 (b) A
17 95VU 2161G7259 W.F. E0160−1−1H 2161−0857 1M CF24 500 20 121 2201VN GND NSA936501TA2206 (b) A
18 131 2161G7259 W.F. E0160−1−1H 2161−0858 1M CF24 1000 40 131 3311VN GND NSA936501TA2206 (b) A
19
20
21
22
23
24
25
(b) = BUNDLE D9000095225695 M1N+M2N= NEW HOOK−UP ON END 1 AND 2
A = ADDED WIRE SH = SHIELD
M1O+M2O= OLD HOOK−UP ON END 1 AND 2 W.F. = WIRE FERRULE
**CONF ALL
**CONF ALL
L
END1 LEAD END2
i
n Instructions
Zone or Wire Lenght Zone or
e
Panel Elec.Ident. Term Terminal P/N Ident. Co Rte Gauge mm Inch Panel Elec.Ident. Term Terminal P/N
1 96VU 248VC−A 25 2161−0426 B 2M RF20 132 1994VC 17 M1O+M2O
2 96VU 248VC−A WS NSA936604CA0931 2161−0426 B 2M RF20 132 1994VC WS NSA936604CA0931 M1N+M2N (1)
3 96VU 248VC−A 27 2161−0426 G 2M RF20 132 1994VC 18 M1O+M2O
4 96VU 248VC−A WS NSA936604CA0931 2161−0426 G 2M RF20 132 1994VC WS NSA936604CA0931 M1N+M2N (1)
5 96VU 248VC−A 24 2161−0426 R 2M RF20 132 1994VC 16 M1O+M2O
6 96VU 248VC−A WS NSA936604CA0931 2161−0426 R 2M RF20 132 1994VC WS NSA936604CA0931 M1N+M2N (1)
7 96VU 248VC−A 23 2161−0426 Y 2M RF20 132 1994VC 15 M1O+M2O
8 96VU 248VC−A WS NSA936604CA0931 2161−0426 Y 2M RF20 132 1994VC WS NSA936604CA0931 M1N+M2N (1)
9
10
11
12 96VU 248VC−A SH 2161G7260 2M MLD20 26500 1060 132 1994VC SH (b) A
13 96VU 248VC−A 25 EN3155−015F2018 2161−7260 B 2M MLD20 26500 1060 132 1994VC 17 EN3155−015F2018 (b) A
14 96VU 248VC−A 27 EN3155−015F2018 2161−7260 G 2M MLD20 26500 1060 132 1994VC 18 EN3155−015F2018 (b) A
15 96VU 248VC−A 24 EN3155−015F2018 2161−7260 R 2M MLD20 26500 1060 132 1994VC 16 EN3155−015F2018 (b) A
16 96VU 248VC−A 23 EN3155−015F2018 2161−7260 Y 2M MLD20 26500 1060 132 1994VC 15 EN3155−015F2018 (b) A
17 96VU 2161G7260 W.F. E0160−1−1H 2161−0860 2M CF24 1000 40 122 2208VN GND NSA936501TA2206 (b) A
18 132 2161G7260 W.F. E0160−1−1H 2161−0861 2M CF24 1500 60 132 3302VN GND NSA936501TA2206 (b) A
19
20
21
22
23
24
25
(b) = BUNDLE D9000095225695 M1N+M2N= NEW HOOK−UP ON END 1 AND 2 (1) = TERMINALS SUPPLIED IN BUNDLE WS = WIRE STOWED
A = ADDED WIRE SH = SHIELD D9000095225695
M1O+M2O= OLD HOOK−UP ON END 1 AND 2 W.F. = WIRE FERRULE GND = GROUND
**CONF ALL
For an explanation of the man-hours and elapsed time, refer to the next page(s).
**CONF ALL
01
ELAPSED TIME ASSUMPTION SERVICE BULLETIN No. A320−21−1208
02
MODIFICATION WIRING
BETWEEN AVIONICS AND 10.00 2 7.00
CARGO COMPARTMENT
REPLACEMENT PLATE IN
0.50 1 0.50
CARGO COMPARTMENT
MODIFICATION STRUCTURE
1.00 1 1.00
ELECTRONICS RACK 90VU
0 2 4 6 8 10 12 14 16 18 20 22 24
SB ELAPSED TIME
TOTAL MANHOURS 28.00 (HOURS)
SB ELAPSED TIME 23.50
NOTES:
01 THIS CHART IS ONLY A PROPOSAL.
OPERATORS MAY DETERMINE THAT ANOTHER WAY
TO DO THE WORK IS MORE SUITABLE FOR THEM.
MH : MANHOURS 02 IF A VSB IS INVOLVED, THE ASSOCIATED MANHOURS
PER : NUMBER OF PERSONS ARE NOT REFLECTED IN THIS GANTT CHART.
ET/S: ELAPSED TIME PER STEP N_SB_211208_5_AAAB_01_01
SB Reporting status
This Service Bulletin will only be incorporated into affected customized Maintenance and Flight
Operations Products if it is duly reported to Airbus.
General information
The SB Reporting policy is published in ISI 00.00.00135. This document provides information regarding:
the SB Reporting means and benefits, the update of customized Maintenance Products and customized
Flight Operations Products.
If this Service Bulletin has an operational impact, refer to paragraph "Flight Operations Products" for
further information on the update of affected Flight Operations Products.
SB Reporting procedure
NOTE: ISI 00.00.00179 covers all the frequently asked questions about SB Reporting. It is revised on a
regular basis.
Use this form to tell us what is your perception of the quality of this Service Bulletin. The reported data
that you provide us will be used to analyse areas of difficulties and to take corrective action to further
improve the quality of our Service Bulletins.
We thank you for the time you have taken in completing this form.
If you have had difficulties in the accomplishment of this SB please quote below the area(s) and give a
short description of the issue.
Comments:
Operator: Date:
Name/Title:
AIRBUS
CUSTOMER SERVICES DIRECTORATE
1 Rond Point Maurice Bellonte
31707 BLAGNAC CEDEX FRANCE