Ordering number: EN4087C
Monolithic Linear IC
LA4598
Two-channel Power Amplifier for Radio Cassette Players (No Heat
Sink Needed during 9 V Operation)
Overview Package Dimensions
unit : mm
The LA4598 is a two-channel power IC that is intended for
use in portable audio equipment. Needing no heat sink during 3113A-SIP14HZ
9 V operation facilitates set design with a small footprint.
[LA4598]
27.0 4.0
20.0
Functions
. Thermal shutdown protector built in.
R1.7
14.5max
. Standby switch built in.
8.4
11.8
7.8
Features
4.6
5.2
. No heat sink needed during 9 V operation 1
. P = 2.9 W × 2 (V = 9 V, R = 3.2 Ω, THD = 10%). 1.94 0.5 14 0.4
1.6
. Less quiescent current. (V = 9 V, 20 mA, typ).
O CC L 3.56 2.2
. Operating voltage range: V op = 4.2 to 16 V.
CC
CC
1.78 3.56
SANYO : SIP14HZ
Specifications
Maximum Ratings at Ta = 25 °C
Allowable power dissipation, Pd max – W
Al heat sink tightening
With arbitrarily large heat torque 4kg.cm
sink
Parameter Symbol Conditions Ratings Unit With silicone grease
applied
Maximum VCC
18 V
supply voltage max
Allowable
No heat
power Pd max* 3.6 W
sink
dissipation
Junction
Tj max +150 °C With Sanyo-
temperature recommended board
Operating
Topr –20 to +75 °C Independent IC
temperature
Storage
Tstg –40 to +150 °C
temperature
* With Sanyo-recommended board (9.0 cm × 8.5 cm × Ambient temperature, Ta – °C
1.5 mm (thickness))
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft’s
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
D3095HA/N1792TS(II) No.4087-1/9
LA4598
Operating Conditions at Ta = 25 °C
Parameter Symbol Conditions Ratings Unit
Recommended supply voltage VCC 9 V
Recommended load resistance RL 3.2 Ω
Operating voltage range VCC op 4.2 to 16.0 V
Operating Characteristics at Ta = 25 °C, VCC = 9 V, f = 1 kHz, Rg = 600 Ω, RL = 3.2 Ω
Parameter Symbol Conditions min typ max unit
Quiescent current ICCO 10 20 40 mA
Voltage gain VG 47 49 51 dB
PO1 THD = 10% 2.2 2.9 W
Output power
PO2 THD = 10%, RL = 4 Ω 2.3 W
Total harmonic distortion THD VO = 2 V 0.3 1.0 %
Input resistance ri 20 30 kΩ
VNO1 Rg = 0, B.P.F = 20 Hz to 20 kHz 0.4 1.0 mV
Output noise voltage
VNO2 Rg = 10 kΩ, B.P.F = 20 Hz to 20 kHz 0.6 2.0 mV
Ripple rejection ratio Rr Rg = 0, fr = 100 Hz, VCCr = 150 mV 40 50 dB
Channel separation CH Sep Rg = 10 kΩ, VO = 0 dB 45 55 dB
Standby current Isd 10 µA
Block Diagram
ch1 BS
ch1 Input
Input Predrive Power
amplifier amplifier amplifier ch1 output
ch1 NF
Power GND
Pre GND
Thermal shutdown
protector
VCC
D.C Bias circuit
Standby switch Standby
ch2 Input Power
Input Predrive
amplifier amplifier amplifier ch2 output
ch2 NF
ch2 BS
Sample Print Pattern
Unit (resistance: Ω, capacitance: F)
Copper-foiled side 85 × 90 mm2
No.4087-2/9
LA4598
Sample Application Circuit
To large signal GND
Mylar capacitor
Unit (resistance:Ω, capacitance:F)
Mylar capacitor
C + R can be added to the negative side of the output capacitor.
However, this is true only for a Sanyo-recommended board; for a set board, artwork must also be
considered.
Description of External Components
C1, C8: Bootstrap capacitors
These capacitors affect low-region output; if the capacitor value is reduced, the low-region output decreases. Therefore,
47 µF or more is desirable.
C2, C6: Output capacitors
If the capacitor value is reduced, low-region roll-off frequency fL and low-region Po worsen.
C3, C7: Oscillation blocking capacitors
Mylar capacitor, which is excellent in temperature characteristics and frequency characteristics is used.
C4: Power supply capacitor
The capacitor values depends on the power supply line loads (motor, and the like.) and transformer ripple component.
1000 µF to 2200 µF is recommended.
C5: Standby capacitor
Pop noise reduction capacitor
C9, C11: Feedback capacitors
In addition to affecting low-region roll-off frequency fL, if the capacitor value is increased, the start-up time is extended.
C10: Decoupling capacitor
This capacitor absorbs power supply ripples; 220 µF is recommended.
R1, R2: Oscillation blocking resistors
The resistor value may be varied 3.3 Ω to 1.0 Ω.
No.4087-3/9
