Technical Data Sheet
Resin
E-SOLDER® 3022
Silver Epoxy
Conductive, Room Temperature Curing Adhesive
High Electrical Conductivity
Good Adhesion Properties
Description
E-SOLDER® 3022 is an epoxy silver paste recommended for applications requiring low electrical resistance and good
adhesive properties. E-SOLDER® 3022 requires the addition of Hardener No. 18 to harden and cure. E-SOLDER®
3022 may be cured at room temperature; however the application of heat will accelerate and shorten the cure time.
Application
Typical applications of E-SOLDER® 3022 are lead terminations, printed circuits and shielding on bases which will not
withstand the elevated temperatures required for fired-on coatings or solders.
Processing
E-SOLDER® 3022 requires a 100:8 mix ratio. To 100 parts of E-SOLDER® 3022, part A by weight, add 8 parts of part
B, hardener No. 18. The hardener and silver epoxy must be weighed carefully and mixed thoroughly until uniform.
Suggested cure cycle per temperature; 77°F (25°C) for 24 hrs or 149°F (65°C) for 3 hrs or 185°F (85°C) for 1.5 hours.
Packaging
E-SOLDER® 3022 is available in 2 oz. squeeze tube kits and 8 oz. containers.
Storage conditions – Shelf life
E-SOLDER® 3022 should be stored in a cool place. Elevated temperatures accelerate the aging of E-SOLDER® 3022.
This results in an increase in viscosity and grainy appearance with time. Although resistivity appears to be unaffected
the handling and dispensing properties become more difficult. Shelf life at 77°F (25°C) is up to 12 months, during which
viscosity can increase or crystallization of the epoxy can occur. Crystallization is completely reversible if part A is
placed in an oven at 110°F (43.3°C) for a few hours.
Von Roll USA
Schenectady, NY 12306 3022
www.vonroll.com
BG 05/05/2022
Physical Properties Test norm Unit Value
Color Silver
Specific Gravity 2.1
Viscosity @ 25ºC (77ºF) Paste
Mix Ratio 100:8
Pot Life (mixed) @ 25ºC (77ºF) hours 1-2
Technical Properties Test norm Unit Value
Volume Resistivity @ 25ºC (77ºF)* ohm-cm 0.019***
Volume Resistivity @ 65ºC (149ºF) ohm-cm 0.003
Lap Shear Tensile Strength,
ASTM D1002 psi 1,800
Aluminium to aluminium, 25ºC
Glass Transition Temperature, Tg DMA, RT-180°C, 5°C/min °C 84
Coefficient of Thermal Expansion Below Tg ppm/°C 55
Coefficient of Thermal Expansion Above Tg ppm/°C 189
Thermal Conductivity ASTM D7984 W/m·K 0.907
Operating Temperature °C 150
NASA Data Reference Number GSFC3207
*Volume Resistivity at 25ºC cure will continue to improve with time.
Health and safety
Precautions: May cause skin sensitization. Do not get on skin, in eyes, or on clothing. Avoid inhalation. Use good
ventilation. In case of skin contact, wash with soap and water. If eye contact occurs, flush with water and get prompt
medical attention.
Safety Data Sheets defining the known hazards and describing safety precautions appropriate for this product are
available upon request from Von Roll USA, Inc., Schenectady, NY, (518) 344-7100 and/or www.vonroll.com. Similar
information for solvents and other chemicals to be used with this product may be obtained from the appropriate
supplier and used accordingly. We recommend following all hygiene and safety standards while processing material.
Liability
The information on this data sheet and the chart above is to be understood as a guideline and has general information. It is not binding for VR and it justifies in no case
any liability. VR reserves the right to change the information at any time. The product properties set forth in this data sheet are based on the results of testing of typical
material produced by the affiliated companies of Von Roll Holding Ltd. (underneath referred as Von Roll). Some variation in product properties is typical. Comments or
suggestions relating to any subject other than product properties are offered only to call the end-user's or other person's attention to considerations which may be relevant
in the independent determination of the use and/or manner of use of product. Von Roll does not claim or warrant that the use of its product will have the results described
in this data sheet or that the information provided is complete, accurate or useful. The user should test the product to determine its properties and its suitability for the
intended use. Von Roll expressly disclaims any liability for any damage, harm, injury, cost or expense to any person resulting directly or indirectly from that person's
reliance on any information contained in this data sheet. Nothing contained in this data sheet constitutes representation or warranty as to any matter whatsoever. Von Roll
makes no warranties whatsoever in this data sheet, expressed or implied, including any implied warranty or fitness for a particular use or purpose. Von Roll shall in no
event be liable for incidental, exemplary, punitive or consequential damages.
Von Roll USA
Schenectady, NY 12306 3022
www.vonroll.com
BG 05/05/2022
