All Sky Camera
LY
N
O
EL
Enclosure
D
O
M
3D
edgett
VIEW IN BROWSER
updated 2. 1. 2023 | published 2. 1. 2023
Summary
This is an actively-cooled enclosure for housing an All Sky camera running
- Thomas Jacquin's software. It can be...
Gadgets > Photo & Video
Tags: camera astrophotography raspberrypi photography
raspberrypizero raspberrypicamera timelapse allskycamera
allsky
This is an actively-cooled enclosure for housing an All Sky camera running
- Thomas Jacquin's software.
It can be equipped with a high quality camera module, a Raspberry Pi
Zero, and a 30mm 5v fan.
To enable remote focusing, consider installing the following remote
software.
Getting Started You will need the following non-included
parts:
• (1) - Raspberry Pi Zero WH
• (1) - Micro SD card (Sandisk preferred)
• (1) - USB to Micro-USB cable of appropriate length (do not exceed
25'). This will be used to deliver power to the Raspberry Pi Zero WH.
• (1) - Raspberry Pi HQ Camera (with tripod mount removed)
• (1) - StarDot 1.55mm lens
• (1) - JMX 4 Inch Acrylic Indoor/Outdoor Clear Camera Dome
• (1) - 30mm x 30mm5-volt Fan
• (1) - Set of assorted M2.5 Cap Head Screws
• (1) - Set of M3, M4, M5 Cap Head Screws
You may need the following additional tools:
• Metric tap set
• Needle nose pliers
• Xacto Knife (for cleaning up small imperfections in prints)
• WD-40 (for lubricating threads of fasteners)
Print Settings
Printer Brand:
Creality
Printer:
Ender 3
Rafts:
No
Supports:
Yes
Resolution:
0.2mm
Infill:
20%
Filament: Hatchbox PLA Cool Gray
Notes:
IMPORTANT: Please review each part in your slicing software before
printing to ensure a logical face is touching the build plate!
This was printed on a Creality CR-6 SE with the hot end set at 200C and
the bed set at 65C.
Please see the following individual print notes below.
*Base
+ Infill: 20% + Material Required: 42g - Hatchbox Cool Gray 1.75mm PLA
+ Adhesion Type: Skirt + Supports: None + Positioning: Bottom Side Down
/ Top Side Up + Quantity: 1
*Camera Carrier
+ Infill: 30% + Material Required: 97g - Hatchbox Cool Gray 1.75mm PLA
+ Adhesion Type: Skirt + Supports: Touching Buildplate + Positioning: Top
Side Down / Bottom Side Up + Quantity: 1
*Dome Retainer
+ Infill: 20% + Material Required: 66g - Hatchbox Cool Gray 1.75mm PLA
+ Adhesion Type: Skirt + Supports: None + Positioning: Top Side Down /
Bottom Side Up + Quantity: 1
*OPTIONAL - Rear Vanity Cap (for angled tripod mounting) + Infill:
30% + Material Required: 45g - Hatchbox Cool Gray 1.75mm PLA +
Adhesion Type: Skirt + Supports: None + Positioning: Bottom Side Down /
Top Side Up + Quantity: 1
Post-Printing
Assembly Instructions
1. Install Raspbian OS onto the SD card and perform any initial
configuration.
2. Remove any support material from your printed pieces.
3. Use your tap set to clean all the threads of your printed pieces
4. Attach the camera ribbon cable to the Raspberry Pi Zero WH. Ensure
the cable is properly secured.
5. Attach the Raspberry Pi Zero WH to thebase using four M2.5 cap
head screws.
6. Insert the micro SD card into the Raspberry Pi Zero WH via the recess
on the side of thebase.
7.) Insert the Micro USB plug through the cable routing recess on the side
of thebase and plug it into the Raspberry Pi Zero WH. 7. Attach the fan to
thecarrier board using four M3 cap head screws and nuts. 8. Carefully
remove the tripod mount from the Raspberry Pi HQ Camera 9. Attach the
remaining end of the camera ribbon cable to the Raspberry Pi HQ Camera
(leave the protective cap in place). Ensure the cable is properly secured.
10. Attach the camera to thecarrier board using four M2.5 cap head
screws and nuts. 11. Plug the fan into the Raspberry Pi's GPIO header. The
red wire should be attached to pin 4 and the black wire should be attached
to pin 6. 12. Carefully set thecarrier board onto thebase. The alignment
pins ensure the two parts are correctly oriented. 13. OPTIONAL: To reduce
the chance of reflection, cut a circle of black wool felt with a an outer
diameter of 92mm and an inner diameter of 37mm. For best results use a
cutting machine -- such as a Silhouette Cameo -- to cut the felt. Set the
felt on top of thecarrier board 14. Set the camera dome on top of
thecarrier board. Ensure the four recesses on the outer edge of the dome
are aligned with the four holes in the top of thecarrier board. 15. Set
thedome retaining ring on top of the rest of the camera assembly.
Ensure the micro USB cable routes along the outer edge of thebase and
exits through the small pass through on thedome retaining ring. 16.
Secure thedome retaining ring to thebase using two M4 cap head
screws
NOTE: You may need to remove the dome retaining ring and dome when
you place the camera in its final location to adjust the lens focus.
Category: Camera
Model files
all_sky_camera_dome_retainergcode.stl
all_sky_camera_carriergcode.stl
optional_all_sky_camera_rear_vanity_cap_for_angled_… .stl
all_sky_camera_basegcode.stl
Find source .stl files on Thingiverse.com
License
This work is licensed under a
Creative Commons (4.0 International License)
Attribution
✖ | Sharing without ATTRIBUTION
✔ | Remix Culture allowed
✔ | Commercial Use
✔ | Free Cultural Works
✔ | Meets Open Definition
