PRODUCT DATA SHEET
SikaSeal®-470 PG Plus
(formerly MSeal 470)
High performance, elastomeric, pourable grade, polysulphide joint sealant
DESCRIPTION FEATURES
SikaSeal®-470 PG Plus is a high grade, chemically cur- ▪ Forms a tough, flexible, elastomeric, weatherproof
ing, two component polysulphide based sealant that seal
forms a tough, flexible, durable, rubber like material ▪ Excellent resistance to deterioration due to weather-
which adheres to most common construction surfaces ing, ozone, U.V. light and high climatic and in-use
and provides fully weatherproof seal in joints subject temperatures
to a high degree of deformation or continuous cyclic ▪ Excellent chemical resistance
movement. ▪ Durable weatherproof sealing even in joints with
high levels of deformation (M.A.F. 25%) or repeated
USES cyclic movement of compression and extension over
a wide temperature range
▪ Bridges, tunnels and other civil engineering struc- ▪ Excellent storage stability of base and curing agent
tures ensures excellent shelf life
▪ Precast concrete paneling, and high-rise buildings ▪ Excellent adhesion to concrete, brickwork, metal,
▪ Concrete and brick foundations, retaining walls and tiling, masonry, stone, steel and glass (check need for
bridge abutments, reservoirs, water treatment primer)
works, sea walls and roads ▪ Lead free curing compounds ensure that the product
▪ Secondary containment areas is safe for handling and application
▪ Wet areas such as kitchens, laundries, bathrooms
and showers, beneath tiles, terraces, decks and bal- CERTIFICATES AND TEST REPORTS
conies
▪ Floor joints subject to heavy usage and traffic ▪ ASTM C920, Type M, Grade P, Class 25, Use T, M & O
▪ Industrial areas and those subject to chemical ▪ Passes fuel ressistance acc. BS 5212: Part 1: 1990
spillage
▪ Remedial repairs to asphalt, concrete, fiber rein-
forced cement or similar slab surface
▪ As a bolt hole sealant for the Wabo® expansion joints
range
PRODUCT INFORMATION
Packaging Ready to mix 5 L packing (Comp. A + Comp. B)
Appearance and colour Pourable liquid available in black or grey colour
Shelf life 12 months from production date
Storage conditions SikaSeal®-470 PG Plus shall be stored in dry conditions, where it is protec-
ted from direct sunlight and at temperatures between +5 °C and +25 °C.
Density ~1.60 kg/l (at 25 °C)
Product Data Sheet
SikaSeal®-470 PG Plus
December 2024, Version 04.01
020515070000000101
1/3
TECHNICAL INFORMATION
Shore A hardness ~15
Chemical resistance Resistant to many chemicals, contact Sika Technical Department for de-
tails.
Joint design Joint configuration
Minimum Joint width: 6 mm
Maximum Joint width: 50 mm
Width: Depth Ratio
The joint width must be designed to suit the movement capability of the
sealant. For movement joints, a width to depth ratio of approximately 2 : 1
must be maintained. For butt joint the width to depth ratio should be 1 : 1.
Minimum joint depth is recommended:
▪ 6 mm for non-porous surfaces
▪ 10 mm for porous surfaces
▪ 20 mm for trafficked joints and joints that are exposed to hydrostatic
pressure
At chamfered elements, don't fill the chamfer with sealant.
APPLICATION INFORMATION
Ambient air temperature +5 °C to +45 °C, min. 3 °C above dew point temperature
Substrate temperature +5 °C to +45 °C
Curing time Initial cure time for light traffic Final cure for chemical attack or wa-
ter immersion
~24 h (at 25 °C) ~14 days (at 25 °C)
~5 h (at 40 °C) ~7 days (at 40 °C)
BASIS OF PRODUCT DATA ECOLOGY, HEALTH AND SAFETY
All technical data stated in this Data Sheet are based User must read the most recent corresponding Safety
on laboratory tests. Actual measured data may vary Data Sheets (SDS) before using any products. The SDS
due to circumstances beyond our control. provides information and advice on the safe handling,
storage and disposal of chemical products and con-
IMPORTANT CONSIDERATIONS tains physical, ecological, toxicological and other
safety-related data.
▪ SikaSeal®-470 PG Plus must be fully cured before
permanent immersion in water. APPLICATION INSTRUCTIONS
▪ Joints subject to total immersion should have a 1:1
(width to depth) ration. SUBSTRATE PREPARATION
▪ Joints should be designed so total movement does
not exceed the ±25 % related to the joint width. ▪ All surfaces must be clean, dry and free from any
▪ When using filler boards in expansion joints to loosely adhering particles.
achieve the correct depth, it is essential to use a ▪ Check the joints edges for soundness and if found
backer rod or insert a bond breaking tape into the weak cut recess and fill up with suitable repair mor-
joint in order to prevent 3-side adhesion. tar.
▪ Paint compatibility with sealant should be checked ▪ Correct joint depth can be established by inserting
prior to painting. closed cell polyethylene backing rod tightly into the
joint.
▪ When the joints have been filled with fiber filled
board, this must be raked back to the required
depth. Use bond breaker tape over the backer ma-
terial.
▪ Protect surfaces with masking tape.
Product Data Sheet
SikaSeal®-470 PG Plus
December 2024, Version 04.01
020515070000000101
2/3
Concrete and Masonry APPLICATION
▪ Surfaces must be clean and dry.
▪ Wire brush thoroughly and remove dust and all con- ▪ Where required, protect the surface with masking
taminants. tape.
Metals ▪ Sealant has a suitable consistency to be poured dir-
▪ Remove any corrosion or millscale by grit or shot- ectly from the container into the joint, when thor-
blast, wirebrush, grinder or chemical remover. oughly mixed.
▪ De-grease the surfaces with clean cloths soaked in ▪ For very narrow joints, it should be filled into a seal-
oil-free cleansing solvent. ant gun.
Wood (bare) ▪ Any masking tape should be removed immediately
▪ Wood surfaces must be clean and dry, cut back or after tooling.
abrade where necessary to sound timber. CLEANING OF EQUIPMENT
Glass and glazed materials
▪ Thoroughly clean the surfaces with clean cloths ▪ Application equipment should be cleaned immedi-
soaked in oil-free cleansing solvent. ately with Sika® Colma Cleaner, acetone or any suit-
Coating surfaces able cleaning solvent after use.
▪ Coating should be removed and the surfaces treated ▪ Hardened / cured material can only be mechanically
as above. removed.
Priming LOCAL RESTRICTIONS
▪ Application of Sika® Primer-101 should not be car-
ried out at below 5°C. Note that as a result of specific local regulations the
▪ A single coat of primer should be applied by brush in declared data and recommended uses for this product
accordance with the instructions on the primer tins. may vary from country to country. Consult the local
▪ Sika® Primer-101 must be allowed to dry to a tack Product Data Sheet for exact product data and uses.
free state before applying SikaSeal®-470 PG Plus.
▪ SikaSeal®-470 PG Plus should be applied within 3 LEGAL NOTES
hours of primer, otherwise repriming will be neces-
sary. The information, and, in particular, the recommenda-
MIXING tions relating to the application and end-use of Sika
products, are given in good faith based on Sika's cur-
▪ Mix and use one complete unit at a time. Do not sub- rent knowledge and experience of the products when
divide. properly stored, handled and applied under normal
▪ SikaSeal®-470 PG Plus is supplied in separate base conditions in accordance with Sika's recommenda-
and catalyst units. Sometimes slight settlement may tions. In practice, the differences in materials, sub-
occur in the catalyst, mix well, before adding to the strates and actual site conditions are such that no war-
base component. ranty in respect of merchantability or of fitness for a
▪ Mix curing agent with base material for 5 - 10 particular purpose, nor any liability arising out of any
minutes using a suitable paddle fitted to a 500 rpm legal relationship whatsoever, can be inferred either
electric drill moving the paddle completely through from this information, or from any written recom-
the mass of the material. mendations, or from any other advice offered. The
▪ The sides and base of the container should be peri- user of the product must test the product’s suitability
odically scraped down with a palette knife to ensure for the intended application and purpose. Sika re-
all of the catalyst is completely blended with the serves the right to change the properties of its
base component. products. The proprietary rights of third parties must
▪ Failure to mix correctly will result in uncured sealant. be observed. All orders are accepted subject to our
▪ Once mixed SikaSeal®-470 PG Plus should be used current terms of sale and delivery. Users must always
immediately. refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.
Sika Gulf B.S.C. (c) Sika UAE LLC Sika Saudi Arabia Limited Sika LLC - Oman
Tel: +973 177 38188 Sika MB Construction Chemicals LLC Sika Construction Chemicals for Sika MB LLC
Email: info@bh.sika.com Sika International Chemicals LLC Manufacturing LLC Tel. +968 22 826 500
Sika Kuwait Cons. Mat. & Paints Co WLL Tel: +971 4 439 8200 Riyadh / Jeddah / Dammam / Rabigh Email: info@om.sika.com
Tel: +965 22 282 296 Email: info@ae.sika.com Tel: +966 9200 22167 Web: gcc.sika.com
Email: sika.kuwait@kw.sika.com Web: gcc.sika.com Email: info@sa.sika.com
Web: gcc.sika.com Web: gcc.sika.com
SikaSeal-470PGPlus-en-AE-(12-2024)-4-1.pdf
Product Data Sheet
SikaSeal®-470 PG Plus
December 2024, Version 04.01
020515070000000101
3/3
