Scribd
Upload
2K views4 pages

Multi Pulse Width Modulation Techniques (MPWM) : Experiment Aim

The document discusses multi-pulse width modulation (MPWM) techniques used to control the output voltage of power converters. There are two main MPWM techniques: uniform pulse width modulation (UPWM) and sinusoidal pulse width modulation (SPWM). UPWM maintains a uniform width for each pulse, while SPWM varies the width of each pulse proportionally to a sine wave. The experiment aims to study these techniques by plotting input and output signals from a comparator for different carrier frequencies and observing the resulting number of pulses per cycle and harmonic reduction. Increasing the carrier frequency increases the number of pulses per cycle and reduces lower-order harmonics in the converter output.

Uploaded by

Ajay Ullal
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2K views4 pages

Multi Pulse Width Modulation Techniques (MPWM) : Experiment Aim

The document discusses multi-pulse width modulation (MPWM) techniques used to control the output voltage of power converters. There are two main MPWM techniques: uniform pulse width modulation (UPWM) and sinusoidal pulse width modulation (SPWM). UPWM maintains a uniform width for each pulse, while SPWM varies the width of each pulse proportionally to a sine wave. The experiment aims to study these techniques by plotting input and output signals from a comparator for different carrier frequencies and observing the resulting number of pulses per cycle and harmonic reduction. Increasing the carrier frequency increases the number of pulses per cycle and reduces lower-order harmonics in the converter output.

Uploaded by

Ajay Ullal
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

University of Technology Laser and Optoelectronics Engineering Department Laser Engineering Branch

Multi Pulse Width Modulation Techniques (MPWM)

Experiment aim
U

To study the commonly used pulse-width modulation techniques

Apparatus
U

1. Power electronic trainer 2. oscilloscope with two probe

Theory
U

In many industrial applications, it is often required to control the output voltage of converters. The most efficient method of controlling the output voltage is to incorporate pulse-width modulation (PWM) control within the inverters. The commonly used techniques are: 1. single pulse-width modulation 2. multi-pulse width modulation

Multi-Pulse width modulation


U

The harmonic content can be reduced by using several pulses in each halfcycle of output voltage. The generation of gating signals for turning on and off transistors is shown in Figure (3). The gating signals are produced by comparing reference signal with triangular carrier wave. The frequency of the reference signal sets the output frequency (fo) and carrier frequency (fc ) determine the number of pulses per half cycle, p:
R R R R

p=

fc 2f o

The variation of modulation index (M) from 0 to 1 varies the pulse from 0 to /p and the output voltage from 0 to Vm.
1

University of Technology Laser and Optoelectronics Engineering Department Laser Engineering Branch

Uniform pulse width modulation (UPWM) Figure (1) shows the uniform pulse width modulation (UPWM). It can be note the reference voltage is square wave changed from the Vm to Vm in frequency = fo. The carrier frequency is triangle wave with amplitude equal to Vc in frequency = fc. If the is the width of each pulse, the rms output voltage can be found from:
2p ( / p+ ) / 22 Vo = Vs d (t ) 2 ( / p ) / 2
1/ 2

= Vs

Sinusoidal Pulse Width modulation Instead of maintaining the width of all pulses the same as in the case of uniform pulse width modulation, the width of each pulse is vary in proportion to the amplitude of a sine wave evaluated at the center of the same pulse.
Carrier signal Vc Vm Reference signal

Gating signal generation

Vs

Output voltage
-Vs

Fig.(1): uniform pulse width modulation (UPWM)

University of Technology Laser and Optoelectronics Engineering Department Laser Engineering Branch

The distortion factor and lower-order harmonics are reduced scientifically. The gating signals as shown in Fig.(2) are generated by comparing a sinusoidal reference signal with a triangular carrier signal of frequency fc. This type of modulation is commonly used in industrial applications and abbreviated as SPWM. The frequency of reference signal (fr ), determine the converter output frequency (fo) and its peak amplitude (Ar ) controls the modulation index, M. The number of pulses per half cycle depends on the carrier frequency.
R R R R R R R R

Reference signal

Carrier signal

Output voltage

Fig.(2): Sinusoidal Pulse width modulation

Procedure Multi-pulse width modulation 1. Apply oscilloscope probe to sine wave generator output, then plot output signal. 2. Set the triangle generator frequency to fc=(400Hz), then determine the number of pulses per half cycle(p). 3. Set the triangle generator frequency to fc=(1000Hz), then determine the number of pulses per half cycle(p). 4. Plot the input and output signals of comparator in the same graph paper along y-axis.
U R R R R

University of Technology Laser and Optoelectronics Engineering Department Laser Engineering Branch

Discussion 1. Comment on the your result 2. How you can reduce the harmonic in the output of the converter. 3. What effect of the increase carrier frequency on the low order harmonic.
U

You might also like