PAKUR POLYTECHNIC, PAKUR
Presents
POWERPOINT PRESENTATION-2019,
on
“GEAR TRAINS”
By-Mithilesh kumar
DATE: 15th FEBRUARY 2019
Venue: Seminar Hall-II
Introduction to Gear Trains
• Sometimes, two or more gears are made to mesh
with each other to transmit power from one shaft
to another. Such a combination is called gear train
or train of toothed wheels.
• A gear train may consist of Spur, Bevel or
Helical gears.
Types of GearTrains
• Following are the different types of gear trains, depending upon
the arrangement of wheels:
1. Simple gear train
2. Compound gear train
3. Reverted gear train
4. Epicyclic gear train
• In the first three types of gear trains, the axes of the shafts over
which the gears are mounted are fixed relative to each other.
• But in case of epicyclic gear trains, the axes of the shafts on which
the gears are mounted may move relative to a fixed axis.
Simple Gear Train
• When there is only one gear on each shaft, as shown in Fig., it is
known as simple geartrain.
• When the distance between the two shafts is small, the two gears 1
and 2 are made to mesh with each other to transmit motion from
one shaft to the other, as shown in Fig. (a).
• Since the gear 1 drives the gear 2, therefore gear 1 is called the driver
and the gear 2 is called the driven or follower.
• It may be noted that the motion of the driven gear is opposite to the
motion of drivinggear.
Let us consider
T1 , T2= No. of teeth on G1 &G2 respectively
N1 , N2= RPM of G1 & G2
𝑵𝟏 𝑻𝟐
Speed Ratio = =
𝑵𝟐 𝑻𝟏
𝑵𝟐 𝑻𝟏
Train Value = =
𝑵𝟏 𝑻𝟐
Compound Gear Train
• When there are more than one gear on a shaft, as shown in
Fig. , it is called a compound train ofgear.
• We have seen that the idle gears, in a simple train of gears
do not effect the speed ratio of the system.
• But these gears are useful in bridging over the space
between the driver and thedriven.
Compound Gear Train ( Continued)
• But whenever the distance between the driver and the driven or
follower has to be bridged over by intermediate gears and at the
same time a great ( or much less ) speed ratio is required, then the
advantage of intermediate gears is increased by providing compound
gears on intermediateshafts.
• In this case, each intermediate shaft has two gears rigidly fixed to it
so that they may have the same speed.
• One of these two gears meshes with the driver and the other with
the driven or follower attached to the next shaft as shown in Fig.
Reverted Gear Train
• When the axes of the first gear (i.e. first
driver) and the last gear (i.e. last driven or
follower) are co-axial, then the gear trainis
known as reverted gear train as shown in
Fig.
• We see that gear 1 (i.e. first driver) drives the
gear 2 (i.e. first driven or follower) in the
opposite direction.
• Since the gears 2 and 3 are mounted on the
same shaft, therefore they form acompound
gear and the gear 3 will rotate in the same
direction as that of gear2.
• The gear 3 (which is now the second driver)
drives the gear 4 (i.e. the last driven or
follower) in the same direction as that of
gear 1. Thus we see that in a reverted gear
train, the motion of the first gear and the
Epicyclic Gear Train
• In an epicyclic gear train, the axes of
the shafts, over which the gears are
mounted, may move relative to a
fixed axis.
• A simple epicyclic gear train is shown
in Fig., where a gear A and the arm C
have a common axis at O1 about
which they canrotate.
• The gear B meshes with gear A and
has its axis on the arm at O2, about
which the gear B can rotate.
• If the arm is fixed, the gear train is simple
and gear A can drive gear B or vice-
versa, but if gear A is fixed and the arm is
rotated about the axis of gear A (i.e.
O1), then the gear B is forced to rotate
upon and around gearA.
• Such a motion is called epicyclic and the
gear trains arranged in such a manner
that one or more of their members move
upon and around another member are
known as epicyclic geartrains (epi. means
upon and cyclic meansaround).
• The epicyclic gear trains may be simple or
compound.
• The epicyclic gear trains are useful for
transmitting high velocity ratios with
gears of moderate size in a comparatively
lesser space.
• The epicyclic gear trains are used in the
back gear of lathe, differential gears of
the automobiles, hoists,pulley
blocks, wrist watchesetc.
Tabular method.
Consider an epicyclic gear train as shown in Fig.
• Let TA = Number of teeth on gear A, and TB = Number of
teeth on gearB.
• First of all, let us suppose that the arm is fixed. Therefore
the axes of both the gears are also fixed relative to each
other.
• When the gear A makes one revolution anticlockwise,the
gear B will make T A /TB revolutions,clockwise.
Tabular method.
• when gear A makes + 1 revolution, then the gear B will make (– TA /TB)
revolutions. This statement of relative motion is entered in the first row of the
table.
• Secondly, if the gear A makes + x revolutions, then the gear B will make – x × TA /
TB revolutions. This statement is entered in the second row of the table. In other
words, multiply the each motion (entered in the first row) by x.
• Thirdly, each element of an epicyclic train is given + y revolutions and entered in the
third row.
• Finally, the motion of each element of the gear train is added up and entered in the
fourth row.
Thank you
