EP603
EP603
Microwave
Microwave Devices
Devices
CHAPTER 2
WAVEGUIDE AND COMPONENTS
- Propagation mode of Electromagnetic Wave
- Microwave Waveguide & Transmission Line
-Characteristic of Waveguide
- Methods of Propagation Modes/ Excitation in
Waveguides
- Discontinuities in Waveguide Components
- Attenuation in Waveguide Components
2.1 Propagation Mode of EM Wave
Transverse Electromagnetic (TEM)
• The electric field, E and the magnetic field, H are oriented
transverse to the direction of propagation of wave.
• Exists in plane waves and transmission lines (2 conductors).
• No cut-off frequency.
y
Ey
Direction of
Travel
x
Hz
Hz
z
• The electric field, E is transverse to the direction of
propagation of wave and the magnetic field, H has
components transverse and in the direction of the wave.
• Exists in waveguide modes.
Ey Direction of
travel
Hx
x
Hy
H
z
Transverse Magnetic (TM)
• The magnetic field, H is transverse to the direction of
propagation of wave and the electric field, E has
components transverse and in the direction of the wave.
• Exists in waveguide modes.
E
Ey
Direction of
travel
x
Ex
Hz
z
Poynting Vector
• It determines that the power radiation is away from the
antenna (the E and H field are perpendicular to each
other).
• Can be expressed mathematically as:
where ;
P=
E
power, W/m²
E = electric field, V/m V
H = magnetic field, A/m
• It represents the power in watts per square meter of the
electromagnetic wave and the velocity of its wave is equal
to the speed of light.
• Steps to sketch the direction of e.m. wave propagation
according to Poynting vector:
a) Determine the direction of propagation.
b) Refer to the electric and magnetic field orientation.
c) Sketch the em wave propagation base on step no. 2.
1. If E-field propagates in the direction of +ve x-axis and H-
field propagates in the direction of +ve y-axis, sketch the
direction of the electromagnetic wave propagation.
Boundary Condition
• It refers to the conditions that E-field and H-field within a
waveguide must meet before energy travels down the
waveguide.
• There are 2 conditions that must be met:
a)For an electric field to exist at the surface of a conductor, it
must be perpendicular to the conductor. An electric field
CANNOT exist parallel to a perfect conductor.
a)For a varying magnetic field to exist, it must form closed
loops in parallel with the conductors and be perpendicular
to the electric field.
• Energy travelling down a waveguide is similar to the
electromagnetic waves travel in free space. The difference
is that the energy in a waveguide is confined to the physical
limits of the guide.
• Since E-field causes a current flow that in turn produces H-
field, both fields always exist at the same time in a
waveguide.
• If one field satisfies one of these boundary conditions, it
must also satisfy the other since neither field can exist
alone.
Spherical Wave
• Is a sphere of constant phase moving away from the
antenna with a velocity equal to the speed of light in a
direction determined by Poynting vector.
• Radiates in all direction uniformly.
Isotropic source Circular curve
(source of e.m. wave form a straight
radiation: radiates in line.
all direction uniformly)
• At a given distance from an antenna radiating an
electromagnetic wave, the phase of the electric field
at that instant of time would be the same over the
surface of the sphere.
H field P points outward
H
E field
Wavefront at a given instant of time Direction of wavefront
Plane Wave
• A small part of the sphere that appears as a flat surface
with the electric field, E and the magnetic field, H be at
right angles (90˚) to each other and are straight lines.
H
2.2 Waveguide & Transmission Line
• Waveguide: hollow metal tube used to guide e.m. energy
from one point to another or through which e.m. waves
propagate.
• Typically one enclosed conductor filled with an insulating
medium.
• The transmission of e.m. energy along waveguide travels at
velocity slower than e.m. energy traveling through free
space.
• Transmission line: Two or more conductors separated by
some insulating medium.
Cont.
Transmission
Waveguides
Line
Coaxial
Stripline Rectangular Circular
Line
Microstrip Ridge Flexible
• It consists of a hollow rectangular waveguide (rectangular
cross section) that can propagate TM and TE modes but not
TEM since only one conductor is present.
• The wall of the guides are conductors and therefore
reflection from them may take place.
• Applications: high-power systems, millimeter wave
applications, satellite systems, precision test applications.
• It is a standard convention to have the longest side of the
waveguide along x-axis [a (width) > b (length)]
• It consists of a hollow, round (circular cross section) metal
pipe that supports TE and TM waveguide modes.
• Applications: used in transmission of circularly polarized
waves, to connect components having circular cross-section
(e.g.: isolators or attenuators) to rectangular waveguide.
• The structure of such a circular waveguide with inner radius
a, is shown below:
• It is formed with a rectangular ridge projecting inward from
one or both of the wide walls in a rectangular waveguide.
• Ridge is used to concentrate the electric field across the
ridge and to lower the cutoff frequency of TE10 mode.
• Applications: attractive for UHF and low microwave ranges.
Ridged Waveguide Using Metal Singled Ridged Waveguide
Bar
Double Ridged Waveguide
• Coaxial line: an electrical cable with an inner conductor
surrounded by a flexible insulating layer, surrounded by a
conducting shield (outer conductor).
• Microwaves travel through the flexible insulation layer.
• Applications: feed lines connecting radio transmitter and
receivers with their antennas, computer network (internet)
connections and distributing cable television(signal).
• It consists of a thin conducting strip of width W that is
centered between two wide conducting ground planes.
• Dielectric material is placed on both sides of the strip
conductor.
• Applications: used inside of the microwave devices
themselves (e.g.: microwave integrated circuitry).
Outer
Conductor
E-field
Dielectric
Ground
plane
w Inner Conductor H-field
• It consists of a conducting strip separated from a ground
plane by a dielectric layer known as the substrate.
• A conductor of width W is printed on a thin, grounded
dielectric substrate of thickness h and relative permittivity
ᵋr.
• Applications: used inside of the microwave devices
themselves (e.g.: microwave integrated circuitry).
• It is used for bends, twists or in applications where certain
criteria may not be fulfilled by normal waveguides.
• Figure below shows some of the flexible waveguides:
• The H bend of Figure (a) is used to turn a 90° corner.
• The E bend Figure (b) also completes a 90° turn in either
an upward or downward direction.
• The twist of Figure (c) is used to effect a shift in the
polarization of the wave.
• Critical (cut-off) frequency, fc(Hz): the lowest frequency for
which a mode will propagate in a waveguide.
• Critical (cut-off) wavelength, λc (m/cycle): the largest
wavelength that can propagate in the waveguide without
any / minimum attenuation (or the smallest free space
wavelength that is just unable to propagate in the
waveguide).
• Group velocity (vg, m/s):
a)The velocity at which a wave propagates.
b)Refers to the velocity of a group of waves.
c)It is also the velocity at which information signals or energy
is propagated.
• Phase velocity (vp, m/s):
a)The velocity at which the wave changes phase.
b)It is the apparent velocity of the wave (i.e.: max electric
intensity point).
c)vp always equal to or greater than vg (vp ≥ vg).
d)It may exceed the velocity of light (velocity in free space).
• In theory: c < vg ≤ vp.
• The relationship between vg, vp and speed of light, c is
given by:
c2 = v + v
g p
• Propagation wavelength in the waveguide (λg, m/s):
a)Wavelength of travelling wave that propagates down the
waveguide.
b)λg will be greater in the waveguide than in free space (λo).
• Waveguide characteristic impedance (Zo, Ω):
a)It depends on the cut-off frequency, which in turn is
determined by the guide dimension.
b)It is also closely related to the characteristic impedance of
free space (377 Ω).
c)Generally, Zo > 377 Ω.
• Dominant mode (mode with lowest cutoff frequency) for
rectangular waveguide is TE1,0.
• A waveguide acts as a high-pass filter in that it passes only
those frequencies above the cutoff frequency.
vp
vg v p c 2
g o
c
c o
g g
f f 1 fc f
2 2 2
c
c c c ( g ) c
fc vp
2a c o 1 fc f
2
377 g
Zo 377 (TE mod e)
1 fc f o
2
o
Z o 377 (TM mod e)
g
1.For a rectangular waveguide with a width of 3 cm and a
desired frequency of operation of 6 GHz (for dominant
mode), determine:
a)Cut-off frequency
b)Cut-off wavelength
c)Group velocity
d)Phase velocity
e)Propagation wavelength in the waveguide
f)Characteristic impedance
2.Repeat Example 1 for a rectangular waveguide with a width
of 2.5 cm and a desired frequency of operation of 7 GHz.
• Dominant mode for circular waveguide is TE1,1.
• For TE1,1 mode, x’11 = 1.841 (solution of Bessel function
equation).
cxnp 2a
fc c
2a xnp
c
vp vg v p c 2
1 fc f
2
o
g
1 fc f
2
g
Z o 377 (TE mod e)
o
o
Z o 377 (TM mod e)
g
1.For a circular waveguide with a radius of 1 cm and a
desired frequency of operation of 10 GHz (for dominant
mode), determine:
a)Cut-off frequency
b)Cut-off wavelength
c)Group velocity
d)Phase velocity
e)Propagation wavelength in the waveguide
f)Characteristic impedance
2.Repeat Example 1 for a circular waveguide with a radius of
2.5 cm and a desired frequency of operation of 7 GHz.
